* Patch by Steven Scholz, 10 Oct 2003LABEL_2003_10_09_2320

  - Add support for Altera FPGA ACEX1K

* Patches by Thomas Lange, 09 Oct 2003:
  - Endian swap ATA identity for all big endian CPUs, not just PPC
  - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize
    args to linux
  - add support for dbau1x00 board (MIPS32)

1 files changed, 0 insertions, 368 deletions

diff --git a/cpu/mips/serial.c b/cpu/mips/serial.c
deleted file mode 100644
index 585227ad6..000000000
--- a/cpu/mips/serial.c
+++ /dev/null
@@ -1,368 +0,0 @@
-/*
- * (INCA) ASC UART support
- */
-
-#include <config.h>
-
-#ifdef CONFIG_PURPLE
-#define	serial_init	asc_serial_init
-#define	serial_putc	asc_serial_putc
-#define	serial_puts	asc_serial_puts
-#define	serial_getc	asc_serial_getc
-#define	serial_tstc	asc_serial_tstc
-#define	serial_setbrg	asc_serial_setbrg
-#endif
-
-#include <common.h>
-#include <asm/inca-ip.h>
-#include "serial.h"
-
-#ifdef CONFIG_PURPLE
-
-#undef ASC_FIFO_PRESENT
-#define TOUT_LOOP	100000
-
-/* Set base address for second FPI interrupt control register bank */
-#define SFPI_INTCON_BASEADDR	0xBF0F0000
-
-/* Register offset from base address */
-#define FBS_ISR		0x00000000	/* Interrupt status register */
-#define FBS_IMR		0x00000008	/* Interrupt mask register */
-#define FBS_IDIS	0x00000010	/* Interrupt disable register */
-
-/* Interrupt status register bits */
-#define FBS_ISR_AT	0x00000040	/* ASC transmit interrupt */
-#define FBS_ISR_AR 	0x00000020	/* ASC receive interrupt */
-#define FBS_ISR_AE	0x00000010	/* ASC error interrupt */
-#define FBS_ISR_AB	0x00000008	/* ASC transmit buffer interrupt */
-#define FBS_ISR_AS      0x00000004 	/* ASC start of autobaud detection interrupt */
-#define FBS_ISR_AF	0x00000002	/* ASC end of autobaud detection interrupt */
-
-#else
-
-#define ASC_FIFO_PRESENT
-
-#endif
-
-
-#define SET_BIT(reg, mask)                  reg |= (mask)
-#define CLEAR_BIT(reg, mask)                reg &= (~mask)
-#define CLEAR_BITS(reg, mask)               CLEAR_BIT(reg, mask)
-#define SET_BITS(reg, mask)                 SET_BIT(reg, mask)
-#define SET_BITFIELD(reg, mask, off, val)   {reg &= (~mask); reg |= (val << off);}
-
-extern uint incaip_get_fpiclk(void);
-
-static int serial_setopt (void);
-
-/* pointer to ASC register base address */
-static volatile incaAsc_t *pAsc = (incaAsc_t *)INCA_IP_ASC;
-
-/******************************************************************************
-*
-* serial_init - initialize a INCAASC channel
-*
-* This routine initializes the number of data bits, parity
-* and set the selected baud rate. Interrupts are disabled.
-* Set the modem control signals if the option is selected.
-*
-* RETURNS: N/A
-*/
-
-int serial_init (void)
-{
-#ifdef CONFIG_INCA_IP
-    /* we have to set PMU.EN13 bit to enable an ASC device*/
-    INCAASC_PMU_ENABLE(13);
-#endif
-
-    /* and we have to set CLC register*/
-    CLEAR_BIT(pAsc->asc_clc, ASCCLC_DISS);
-    SET_BITFIELD(pAsc->asc_clc, ASCCLC_RMCMASK, ASCCLC_RMCOFFSET, 0x0001);
-
-    /* initialy we are in async mode */
-    pAsc->asc_con = ASCCON_M_8ASYNC;
-
-    /* select input port */
-    pAsc->asc_pisel = (CONSOLE_TTY & 0x1);
-
-#ifdef ASC_FIFO_PRESENT
-    /* TXFIFO's filling level */
-    SET_BITFIELD(pAsc->asc_txfcon, ASCTXFCON_TXFITLMASK,
-		    ASCTXFCON_TXFITLOFF, INCAASC_TXFIFO_FL);
-    /* enable TXFIFO */
-    SET_BIT(pAsc->asc_txfcon, ASCTXFCON_TXFEN);
-
-    /* RXFIFO's filling level */
-    SET_BITFIELD(pAsc->asc_txfcon, ASCRXFCON_RXFITLMASK,
-		    ASCRXFCON_RXFITLOFF, INCAASC_RXFIFO_FL);
-    /* enable RXFIFO */
-    SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXFEN);
-#endif
-
-    /* enable error signals */
-    SET_BIT(pAsc->asc_con, ASCCON_FEN);
-    SET_BIT(pAsc->asc_con, ASCCON_OEN);
-
-#ifdef CONFIG_INCA_IP
-    /* acknowledge ASC interrupts */
-    ASC_INTERRUPTS_CLEAR(INCAASC_IRQ_LINE_ALL);
-
-    /* disable ASC interrupts */
-    ASC_INTERRUPTS_DISABLE(INCAASC_IRQ_LINE_ALL);
-#endif
-
-#ifdef ASC_FIFO_PRESENT
-    /* set FIFOs into the transparent mode */
-    SET_BIT(pAsc->asc_txfcon, ASCTXFCON_TXTMEN);
-    SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXTMEN);
-#endif
-
-    /* set baud rate */
-    serial_setbrg();
-
-    /* set the options */
-    serial_setopt();
-
-    return 0;
-}
-
-void serial_setbrg (void)
-{
-    ulong      uiReloadValue, fdv;
-    ulong      f_ASC;
-
-#ifdef CONFIG_INCA_IP
-    f_ASC = incaip_get_fpiclk();
-#else
-    f_ASC = ASC_CLOCK_RATE;
-#endif
-
-#ifndef INCAASC_USE_FDV
-    fdv = 2;
-    uiReloadValue = (f_ASC / (fdv * 16 * CONFIG_BAUDRATE)) - 1;
-#else
-    fdv = INCAASC_FDV_HIGH_BAUDRATE;
-    uiReloadValue = (f_ASC / (8192 * CONFIG_BAUDRATE / fdv)) - 1;
-#endif /* INCAASC_USE_FDV */
-
-    if ( (uiReloadValue < 0) || (uiReloadValue > 8191) )
-    {
-#ifndef INCAASC_USE_FDV
-	fdv = 3;
-	uiReloadValue = (f_ASC / (fdv * 16 * CONFIG_BAUDRATE)) - 1;
-#else
-	fdv = INCAASC_FDV_LOW_BAUDRATE;
-	uiReloadValue = (f_ASC / (8192 * CONFIG_BAUDRATE / fdv)) - 1;
-#endif /* INCAASC_USE_FDV */
-
-	if ( (uiReloadValue < 0) || (uiReloadValue > 8191) )
-	{
-	    return;    /* can't impossibly generate that baud rate */
-	}
-    }
-
-    /* Disable Baud Rate Generator; BG should only be written when R=0 */
-    CLEAR_BIT(pAsc->asc_con, ASCCON_R);
-
-#ifndef INCAASC_USE_FDV
-    /*
-     * Disable Fractional Divider (FDE)
-     * Divide clock by reload-value + constant (BRS)
-     */
-    /* FDE = 0 */
-    CLEAR_BIT(pAsc->asc_con, ASCCON_FDE);
-
-    if ( fdv == 2 )
-	CLEAR_BIT(pAsc->asc_con, ASCCON_BRS);   /* BRS = 0 */
-    else
-	SET_BIT(pAsc->asc_con, ASCCON_BRS); /* BRS = 1 */
-
-#else /* INCAASC_USE_FDV */
-
-    /* Enable Fractional Divider */
-    SET_BIT(pAsc->asc_con, ASCCON_FDE); /* FDE = 1 */
-
-    /* Set fractional divider value */
-    pAsc->asc_fdv = fdv & ASCFDV_VALUE_MASK;
-
-#endif /* INCAASC_USE_FDV */
-
-    /* Set reload value in BG */
-    pAsc->asc_bg = uiReloadValue;
-
-    /* Enable Baud Rate Generator */
-    SET_BIT(pAsc->asc_con, ASCCON_R);           /* R = 1 */
-}
-
-/*******************************************************************************
-*
-* serial_setopt - set the serial options
-*
-* Set the channel operating mode to that specified. Following options
-* are supported: CREAD, CSIZE, PARENB, and PARODD.
-*
-* Note, this routine disables the transmitter.  The calling routine
-* may have to re-enable it.
-*
-* RETURNS:
-* Returns 0 to indicate success, otherwise -1 is returned
-*/
-
-static int serial_setopt (void)
-{
-    ulong  con;
-
-    switch ( ASC_OPTIONS & ASCOPT_CSIZE )
-    {
-    /* 7-bit-data */
-    case ASCOPT_CS7:
-	con = ASCCON_M_7ASYNCPAR;   /* 7-bit-data and parity bit */
-	break;
-
-    /* 8-bit-data */
-    case ASCOPT_CS8:
-	if ( ASC_OPTIONS & ASCOPT_PARENB )
-	    con = ASCCON_M_8ASYNCPAR;   /* 8-bit-data and parity bit */
-	else
-	    con = ASCCON_M_8ASYNC;      /* 8-bit-data no parity */
-	break;
-
-    /*
-     *  only 7 and 8-bit frames are supported
-     *  if we don't use IOCTL extensions
-     */
-    default:
-	return -1;
-    }
-
-    if ( ASC_OPTIONS & ASCOPT_STOPB )
-	SET_BIT(con, ASCCON_STP);       /* 2 stop bits */
-    else
-	CLEAR_BIT(con, ASCCON_STP);     /* 1 stop bit */
-
-    if ( ASC_OPTIONS & ASCOPT_PARENB )
-	SET_BIT(con, ASCCON_PEN);           /* enable parity checking */
-    else
-	CLEAR_BIT(con, ASCCON_PEN);         /* disable parity checking */
-
-    if ( ASC_OPTIONS & ASCOPT_PARODD )
-	SET_BIT(con, ASCCON_ODD);       /* odd parity */
-    else
-	CLEAR_BIT(con, ASCCON_ODD);     /* even parity */
-
-    if ( ASC_OPTIONS & ASCOPT_CREAD )
-	SET_BIT(pAsc->asc_whbcon, ASCWHBCON_SETREN); /* Receiver enable */
-
-    pAsc->asc_con |= con;
-
-    return 0;
-}
-
-void serial_putc (const char c)
-{
-#ifdef ASC_FIFO_PRESENT
-    uint txFl = 0;
-#else
-    uint timeout = 0;
-#endif
-
-    if (c == '\n') serial_putc ('\r');
-
-#ifdef ASC_FIFO_PRESENT
-    /* check do we have a free space in the TX FIFO */
-    /* get current filling level */
-    do
-    {
-	txFl = ( pAsc->asc_fstat & ASCFSTAT_TXFFLMASK ) >> ASCFSTAT_TXFFLOFF;
-    }
-    while ( txFl == INCAASC_TXFIFO_FULL );
-#else
-
-    while(!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) &
-			   FBS_ISR_AB))
-    {
-	    if (timeout++ > TOUT_LOOP)
-	    {
-		    break;
-	    }
-    }
-#endif
-
-    pAsc->asc_tbuf = c; /* write char to Transmit Buffer Register */
-
-#ifndef ASC_FIFO_PRESENT
-    *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AB |
-								 FBS_ISR_AT;
-#endif
-
-    /* check for errors */
-    if ( pAsc->asc_con & ASCCON_OE )
-    {
-	SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLROE);
-	return;
-    }
-}
-
-void serial_puts (const char *s)
-{
-    while (*s)
-    {
-	serial_putc (*s++);
-    }
-}
-
-int serial_getc (void)
-{
-    ulong symbol_mask;
-    char c;
-
-    while (!serial_tstc());
-
-    symbol_mask =
-	((ASC_OPTIONS & ASCOPT_CSIZE) == ASCOPT_CS7) ? (0x7f) : (0xff);
-
-    c = (char)(pAsc->asc_rbuf & symbol_mask);
-
-#ifndef ASC_FIFO_PRESENT
-    *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AR;
-#endif
-
-    return c;
-}
-
-int serial_tstc (void)
-{
-    int res = 1;
-
-#ifdef ASC_FIFO_PRESENT
-    if ( (pAsc->asc_fstat & ASCFSTAT_RXFFLMASK) == 0 )
-    {
-	res = 0;
-    }
-#else
-    if (!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) &
-								FBS_ISR_AR))
-
-    {
-	res = 0;
-    }
-#endif
-    else if ( pAsc->asc_con & ASCCON_FE )
-    {
-	SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLRFE);
-	res = 0;
-    }
-    else if ( pAsc->asc_con & ASCCON_PE )
-    {
-	SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLRPE);
-	res = 0;
-    }
-    else if ( pAsc->asc_con & ASCCON_OE )
-    {
-	SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLROE);
-	res = 0;
-    }
-
-    return res;
-}