diff options
Diffstat (limited to 'include/tsec.h')
| -rw-r--r-- | include/tsec.h | 298 |
1 files changed, 23 insertions, 275 deletions
diff --git a/include/tsec.h b/include/tsec.h index a066d97be..8ed30aca0 100644 --- a/include/tsec.h +++ b/include/tsec.h @@ -19,30 +19,36 @@ #include <net.h> #include <config.h> +#include <phy.h> +#include <asm/fsl_enet.h> #define TSEC_SIZE 0x01000 #define TSEC_MDIO_OFFSET 0x01000 +#define CONFIG_SYS_MDIO_BASE_ADDR (TSEC_BASE_ADDR + 0x520) + +#define DEFAULT_MII_NAME "FSL_MDIO" + #define STD_TSEC_INFO(num) \ { \ .regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)), \ - .miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR), \ - .miiregs_sgmii = (tsec_mdio_t *)(MDIO_BASE_ADDR \ + .miiregs_sgmii = (struct tsec_mii_mng *)(CONFIG_SYS_MDIO_BASE_ADDR \ + (num - 1) * TSEC_MDIO_OFFSET), \ .devname = CONFIG_TSEC##num##_NAME, \ .phyaddr = TSEC##num##_PHY_ADDR, \ - .flags = TSEC##num##_FLAGS \ + .flags = TSEC##num##_FLAGS, \ + .mii_devname = DEFAULT_MII_NAME \ } #define SET_STD_TSEC_INFO(x, num) \ { \ x.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)); \ - x.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR); \ - x.miiregs_sgmii = (tsec_mdio_t *)(MDIO_BASE_ADDR \ + x.miiregs_sgmii = (struct tsec_mii_mng *)(CONFIG_SYS_MDIO_BASE_ADDR \ + (num - 1) * TSEC_MDIO_OFFSET); \ x.devname = CONFIG_TSEC##num##_NAME; \ x.phyaddr = TSEC##num##_PHY_ADDR; \ x.flags = TSEC##num##_FLAGS;\ + x.mii_devname = DEFAULT_MII_NAME;\ } #define MAC_ADDR_LEN 6 @@ -51,8 +57,6 @@ #define TSEC_TIMEOUT 1000 #define TOUT_LOOP 1000000 -#define PHY_AUTONEGOTIATE_TIMEOUT 5000 /* in ms */ - /* TBI register addresses */ #define TBI_CR 0x00 #define TBI_SR 0x01 @@ -96,204 +100,14 @@ #define ECNTRL_INIT_SETTINGS 0x00001000 #define ECNTRL_TBI_MODE 0x00000020 +#define ECNTRL_REDUCED_MODE 0x00000010 #define ECNTRL_R100 0x00000008 +#define ECNTRL_REDUCED_MII_MODE 0x00000004 #define ECNTRL_SGMII_MODE 0x00000002 -#define miim_end -2 -#define miim_read -1 - #ifndef CONFIG_SYS_TBIPA_VALUE #define CONFIG_SYS_TBIPA_VALUE 0x1f #endif -#define MIIMCFG_INIT_VALUE 0x00000003 -#define MIIMCFG_RESET 0x80000000 - -#define MIIMIND_BUSY 0x00000001 -#define MIIMIND_NOTVALID 0x00000004 - -#define MIIM_CONTROL 0x00 -#define MIIM_CONTROL_RESET 0x00009140 -#define MIIM_CONTROL_INIT 0x00001140 -#define MIIM_CONTROL_RESTART 0x00001340 -#define MIIM_ANEN 0x00001000 - -#define MIIM_CR 0x00 -#define MIIM_CR_RST 0x00008000 -#define MIIM_CR_INIT 0x00001000 - -#define MIIM_STATUS 0x1 -#define MIIM_STATUS_AN_DONE 0x00000020 -#define MIIM_STATUS_LINK 0x0004 - -#define MIIM_PHYIR1 0x2 -#define MIIM_PHYIR2 0x3 - -#define MIIM_ANAR 0x4 -#define MIIM_ANAR_INIT 0x1e1 - -#define MIIM_TBI_ANLPBPA 0x5 -#define MIIM_TBI_ANLPBPA_HALF 0x00000040 -#define MIIM_TBI_ANLPBPA_FULL 0x00000020 - -#define MIIM_TBI_ANEX 0x6 -#define MIIM_TBI_ANEX_NP 0x00000004 -#define MIIM_TBI_ANEX_PRX 0x00000002 - -#define MIIM_GBIT_CONTROL 0x9 -#define MIIM_GBIT_CONTROL_INIT 0xe00 - -#define MIIM_EXT_PAGE_ACCESS 0x1f - -/* Broadcom BCM54xx -- taken from linux sungem_phy */ -#define MIIM_BCM54xx_AUXCNTL 0x18 -#define MIIM_BCM54xx_AUXCNTL_ENCODE(val) ((val & 0x7) << 12)|(val & 0x7) -#define MIIM_BCM54xx_AUXSTATUS 0x19 -#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK 0x0700 -#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT 8 - -#define MIIM_BCM54XX_SHD 0x1c /* 0x1c shadow registers */ -#define MIIM_BCM54XX_SHD_WRITE 0x8000 -#define MIIM_BCM54XX_SHD_VAL(x) ((x & 0x1f) << 10) -#define MIIM_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0) -#define MIIM_BCM54XX_SHD_WR_ENCODE(val, data) \ - (MIIM_BCM54XX_SHD_WRITE | MIIM_BCM54XX_SHD_VAL(val) | \ - MIIM_BCM54XX_SHD_DATA(data)) - -#define MIIM_BCM54XX_EXP_DATA 0x15 /* Expansion register data */ -#define MIIM_BCM54XX_EXP_SEL 0x17 /* Expansion register select */ -#define MIIM_BCM54XX_EXP_SEL_SSD 0x0e00 /* Secondary SerDes select */ -#define MIIM_BCM54XX_EXP_SEL_ER 0x0f00 /* Expansion register select */ - -/* Cicada Auxiliary Control/Status Register */ -#define MIIM_CIS8201_AUX_CONSTAT 0x1c -#define MIIM_CIS8201_AUXCONSTAT_INIT 0x0004 -#define MIIM_CIS8201_AUXCONSTAT_DUPLEX 0x0020 -#define MIIM_CIS8201_AUXCONSTAT_SPEED 0x0018 -#define MIIM_CIS8201_AUXCONSTAT_GBIT 0x0010 -#define MIIM_CIS8201_AUXCONSTAT_100 0x0008 - -/* Cicada Extended Control Register 1 */ -#define MIIM_CIS8201_EXT_CON1 0x17 -#define MIIM_CIS8201_EXTCON1_INIT 0x0000 - -/* Cicada 8204 Extended PHY Control Register 1 */ -#define MIIM_CIS8204_EPHY_CON 0x17 -#define MIIM_CIS8204_EPHYCON_INIT 0x0006 -#define MIIM_CIS8204_EPHYCON_RGMII 0x1100 - -/* Cicada 8204 Serial LED Control Register */ -#define MIIM_CIS8204_SLED_CON 0x1b -#define MIIM_CIS8204_SLEDCON_INIT 0x1115 - -#define MIIM_GBIT_CON 0x09 -#define MIIM_GBIT_CON_ADVERT 0x0e00 - -/* Entry for Vitesse VSC8244 regs starts here */ -/* Vitesse VSC8244 Auxiliary Control/Status Register */ -#define MIIM_VSC8244_AUX_CONSTAT 0x1c -#define MIIM_VSC8244_AUXCONSTAT_INIT 0x0000 -#define MIIM_VSC8244_AUXCONSTAT_DUPLEX 0x0020 -#define MIIM_VSC8244_AUXCONSTAT_SPEED 0x0018 -#define MIIM_VSC8244_AUXCONSTAT_GBIT 0x0010 -#define MIIM_VSC8244_AUXCONSTAT_100 0x0008 -#define MIIM_CONTROL_INIT_LOOPBACK 0x4000 - -/* Vitesse VSC8244 Extended PHY Control Register 1 */ -#define MIIM_VSC8244_EPHY_CON 0x17 -#define MIIM_VSC8244_EPHYCON_INIT 0x0006 - -/* Vitesse VSC8244 Serial LED Control Register */ -#define MIIM_VSC8244_LED_CON 0x1b -#define MIIM_VSC8244_LEDCON_INIT 0xF011 - -/* Entry for Vitesse VSC8601 regs starts here (Not complete) */ -/* Vitesse VSC8601 Extended PHY Control Register 1 */ -#define MIIM_VSC8601_EPHY_CON 0x17 -#define MIIM_VSC8601_EPHY_CON_INIT_SKEW 0x1120 -#define MIIM_VSC8601_SKEW_CTRL 0x1c - -/* 88E1011 PHY Status Register */ -#define MIIM_88E1011_PHY_STATUS 0x11 -#define MIIM_88E1011_PHYSTAT_SPEED 0xc000 -#define MIIM_88E1011_PHYSTAT_GBIT 0x8000 -#define MIIM_88E1011_PHYSTAT_100 0x4000 -#define MIIM_88E1011_PHYSTAT_DUPLEX 0x2000 -#define MIIM_88E1011_PHYSTAT_SPDDONE 0x0800 -#define MIIM_88E1011_PHYSTAT_LINK 0x0400 - -#define MIIM_88E1011_PHY_SCR 0x10 -#define MIIM_88E1011_PHY_MDI_X_AUTO 0x0060 - -/* 88E1111 PHY LED Control Register */ -#define MIIM_88E1111_PHY_LED_CONTROL 24 -#define MIIM_88E1111_PHY_LED_DIRECT 0x4100 -#define MIIM_88E1111_PHY_LED_COMBINE 0x411C - -/* 88E1121 PHY LED Control Register */ -#define MIIM_88E1121_PHY_LED_CTRL 16 -#define MIIM_88E1121_PHY_LED_PAGE 3 -#define MIIM_88E1121_PHY_LED_DEF 0x0030 - -/* 88E1121 PHY IRQ Enable/Status Register */ -#define MIIM_88E1121_PHY_IRQ_EN 18 -#define MIIM_88E1121_PHY_IRQ_STATUS 19 - -#define MIIM_88E1121_PHY_PAGE 22 - -/* 88E1145 Extended PHY Specific Control Register */ -#define MIIM_88E1145_PHY_EXT_CR 20 -#define MIIM_M88E1145_RGMII_RX_DELAY 0x0080 -#define MIIM_M88E1145_RGMII_TX_DELAY 0x0002 - -#define MIIM_88E1145_PHY_PAGE 29 -#define MIIM_88E1145_PHY_CAL_OV 30 - -/* RTL8211B PHY Status Register */ -#define MIIM_RTL8211B_PHY_STATUS 0x11 -#define MIIM_RTL8211B_PHYSTAT_SPEED 0xc000 -#define MIIM_RTL8211B_PHYSTAT_GBIT 0x8000 -#define MIIM_RTL8211B_PHYSTAT_100 0x4000 -#define MIIM_RTL8211B_PHYSTAT_DUPLEX 0x2000 -#define MIIM_RTL8211B_PHYSTAT_SPDDONE 0x0800 -#define MIIM_RTL8211B_PHYSTAT_LINK 0x0400 - -/* DM9161 Control register values */ -#define MIIM_DM9161_CR_STOP 0x0400 -#define MIIM_DM9161_CR_RSTAN 0x1200 - -#define MIIM_DM9161_SCR 0x10 -#define MIIM_DM9161_SCR_INIT 0x0610 - -/* DM9161 Specified Configuration and Status Register */ -#define MIIM_DM9161_SCSR 0x11 -#define MIIM_DM9161_SCSR_100F 0x8000 -#define MIIM_DM9161_SCSR_100H 0x4000 -#define MIIM_DM9161_SCSR_10F 0x2000 -#define MIIM_DM9161_SCSR_10H 0x1000 - -/* DM9161 10BT Configuration/Status */ -#define MIIM_DM9161_10BTCSR 0x12 -#define MIIM_DM9161_10BTCSR_INIT 0x7800 - -/* LXT971 Status 2 registers */ -#define MIIM_LXT971_SR2 0x11 /* Status Register 2 */ -#define MIIM_LXT971_SR2_SPEED_MASK 0x4200 -#define MIIM_LXT971_SR2_10HDX 0x0000 /* 10 Mbit half duplex selected */ -#define MIIM_LXT971_SR2_10FDX 0x0200 /* 10 Mbit full duplex selected */ -#define MIIM_LXT971_SR2_100HDX 0x4000 /* 100 Mbit half duplex selected */ -#define MIIM_LXT971_SR2_100FDX 0x4200 /* 100 Mbit full duplex selected */ - -/* DP83865 Control register values */ -#define MIIM_DP83865_CR_INIT 0x9200 - -/* DP83865 Link and Auto-Neg Status Register */ -#define MIIM_DP83865_LANR 0x11 -#define MIIM_DP83865_SPD_MASK 0x0018 -#define MIIM_DP83865_SPD_1000 0x0010 -#define MIIM_DP83865_SPD_100 0x0008 -#define MIIM_DP83865_DPX_FULL 0x0002 - -#define MIIM_READ_COMMAND 0x00000001 #define MRBLR_INIT_SETTINGS PKTSIZE_ALIGN @@ -467,22 +281,6 @@ typedef struct tsec_hash_regs uint res2[24]; } tsec_hash_t; -typedef struct tsec_mdio { - uint res1[4]; - uint ieventm; - uint imaskm; - uint res2; - uint emapm; - uint res3[320]; - uint miimcfg; /* MII Management: Configuration */ - uint miimcom; /* MII Management: Command */ - uint miimadd; /* MII Management: Address */ - uint miimcon; /* MII Management: Control */ - uint miimstat; /* MII Management: Status */ - uint miimind; /* MII Management: Indicators */ - uint res4[690]; -} tsec_mdio_t; - typedef struct tsec { /* General Control and Status Registers (0x2_n000) */ @@ -578,79 +376,29 @@ typedef struct tsec uint resc00[256]; } tsec_t; -#define TSEC_GIGABIT (1) +#define TSEC_GIGABIT (1 << 0) -/* This flag currently only has - * meaning if we're using the eTSEC */ +/* These flags currently only have meaning if we're using the eTSEC */ #define TSEC_REDUCED (1 << 1) /* MAC-PHY interface uses RGMII */ #define TSEC_SGMII (1 << 2) /* MAC-PHY interface uses SGMII */ -#define TSEC_FIBER (1 << 3) /* PHY uses fiber, eg 1000 Base-X */ struct tsec_private { tsec_t *regs; - tsec_mdio_t *phyregs; - tsec_mdio_t *phyregs_sgmii; - struct phy_info *phyinfo; + struct tsec_mii_mng *phyregs_sgmii; + struct phy_device *phydev; + phy_interface_t interface; + struct mii_dev *bus; uint phyaddr; + char mii_devname[16]; u32 flags; - uint link; - uint duplexity; - uint speed; -}; - - -/* - * struct phy_cmd: A command for reading or writing a PHY register - * - * mii_reg: The register to read or write - * - * mii_data: For writes, the value to put in the register. - * A value of -1 indicates this is a read. - * - * funct: A function pointer which is invoked for each command. - * For reads, this function will be passed the value read - * from the PHY, and process it. - * For writes, the result of this function will be written - * to the PHY register - */ -struct phy_cmd { - uint mii_reg; - uint mii_data; - uint (*funct) (uint mii_reg, struct tsec_private * priv); -}; - -/* struct phy_info: a structure which defines attributes for a PHY - * - * id will contain a number which represents the PHY. During - * startup, the driver will poll the PHY to find out what its - * UID--as defined by registers 2 and 3--is. The 32-bit result - * gotten from the PHY will be shifted right by "shift" bits to - * discard any bits which may change based on revision numbers - * unimportant to functionality - * - * The struct phy_cmd entries represent pointers to an arrays of - * commands which tell the driver what to do to the PHY. - */ -struct phy_info { - uint id; - char *name; - uint shift; - /* Called to configure the PHY, and modify the controller - * based on the results */ - struct phy_cmd *config; - - /* Called when starting up the controller */ - struct phy_cmd *startup; - - /* Called when bringing down the controller */ - struct phy_cmd *shutdown; }; struct tsec_info_struct { tsec_t *regs; - tsec_mdio_t *miiregs; - tsec_mdio_t *miiregs_sgmii; + struct tsec_mii_mng *miiregs_sgmii; char *devname; + char *mii_devname; + phy_interface_t interface; unsigned int phyaddr; u32 flags; }; |