diff options
Diffstat (limited to 'include/ps2mult.h')
| -rw-r--r-- | include/ps2mult.h | 99 |
1 files changed, 0 insertions, 99 deletions
diff --git a/include/ps2mult.h b/include/ps2mult.h index 599cb6dc4..1a38733b7 100644 --- a/include/ps2mult.h +++ b/include/ps2mult.h @@ -53,103 +53,4 @@ struct serial_state { u8 *iomem_base; }; -#define UART_RX 0 /* In: Receive buffer (DLAB=0) */ -#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ -#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ - -#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ -#define UART_IER 1 /* Out: Interrupt Enable Register */ - -#define UART_IIR 2 /* In: Interrupt ID Register */ -#define UART_FCR 2 /* Out: FIFO Control Register */ - -#define UART_LCR 3 /* Out: Line Control Register */ -#define UART_MCR 4 /* Out: Modem Control Register */ -#define UART_LSR 5 /* In: Line Status Register */ -#define UART_MSR 6 /* In: Modem Status Register */ -#define UART_SCR 7 /* I/O: Scratch Register */ - -/* - * These are the definitions for the FIFO Control Register - * (16650 only) - */ -#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ -#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ -#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ -#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ -#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ -#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ -#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ -#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ -#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ - -/* - * These are the definitions for the Line Control Register - * - * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting - * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. - */ -#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ -#define UART_LCR_SBC 0x40 /* Set break control */ -#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ -#define UART_LCR_EPAR 0x10 /* Even parity select */ -#define UART_LCR_PARITY 0x08 /* Parity Enable */ -#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ -#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ -#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ -#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ -#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ - -/* - * These are the definitions for the Line Status Register - */ -#define UART_LSR_TEMT 0x40 /* Transmitter empty */ -#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ -#define UART_LSR_BI 0x10 /* Break interrupt indicator */ -#define UART_LSR_FE 0x08 /* Frame error indicator */ -#define UART_LSR_PE 0x04 /* Parity error indicator */ -#define UART_LSR_OE 0x02 /* Overrun error indicator */ -#define UART_LSR_DR 0x01 /* Receiver data ready */ - -/* - * These are the definitions for the Interrupt Identification Register - */ -#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ -#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ - -#define UART_IIR_MSI 0x00 /* Modem status interrupt */ -#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ -#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ -#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ - -/* - * These are the definitions for the Interrupt Enable Register - */ -#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ -#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ -#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ -#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ - -/* - * These are the definitions for the Modem Control Register - */ -#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ -#define UART_MCR_OUT2 0x08 /* Out2 complement */ -#define UART_MCR_OUT1 0x04 /* Out1 complement */ -#define UART_MCR_RTS 0x02 /* RTS complement */ -#define UART_MCR_DTR 0x01 /* DTR complement */ - -/* - * These are the definitions for the Modem Status Register - */ -#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ -#define UART_MSR_RI 0x40 /* Ring Indicator */ -#define UART_MSR_DSR 0x20 /* Data Set Ready */ -#define UART_MSR_CTS 0x10 /* Clear to Send */ -#define UART_MSR_DDCD 0x08 /* Delta DCD */ -#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ -#define UART_MSR_DDSR 0x02 /* Delta DSR */ -#define UART_MSR_DCTS 0x01 /* Delta CTS */ -#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ - #endif /* __LINUX_PS2MULT_H */ |