diff options
Diffstat (limited to 'doc/README.ppc440')
| -rw-r--r-- | doc/README.ppc440 | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/doc/README.ppc440 b/doc/README.ppc440 index 2e04abacc..0a5f99fb1 100644 --- a/doc/README.ppc440 +++ b/doc/README.ppc440 @@ -47,25 +47,25 @@ the cpu-specific code (vs. board-specific code), so you should at least review these before deciding to make any changes ... it will probably save you some headaches ;-) -CFG_SDRAM_BASE - The virtual address where SDRAM is mapped (always 0) +CONFIG_SYS_SDRAM_BASE - The virtual address where SDRAM is mapped (always 0) -CFG_FLASH_BASE - The virtual address where FLASH is mapped. +CONFIG_SYS_FLASH_BASE - The virtual address where FLASH is mapped. -CFG_PCI_MEMBASE - The virtual address where PCI-bus memory is mapped. +CONFIG_SYS_PCI_MEMBASE - The virtual address where PCI-bus memory is mapped. This mapping provides access to PCI-bus memory. -CFG_PERIPHERAL_BASE - The virtual address where the 440 memory-mapped +CONFIG_SYS_PERIPHERAL_BASE - The virtual address where the 440 memory-mapped peripherals are mapped. (e.g. -- UART registers, IIC registers, etc). -CFG_ISRAM_BASE - The virtual address where the 440 internal SRAM is +CONFIG_SYS_ISRAM_BASE - The virtual address where the 440 internal SRAM is mapped. The internal SRAM is equivalent to 405gp OCM and is used for the initial stack. -CFG_PCI_BASE - The virtual address where the 440 PCI-x bridge config +CONFIG_SYS_PCI_BASE - The virtual address where the 440 PCI-x bridge config registers are mapped. -CFG_PCI_TARGBASE - The PCI address that is mapped to the virtual address - defined by CFG_PCI_MEMBASE. +CONFIG_SYS_PCI_TARGBASE - The PCI address that is mapped to the virtual address + defined by CONFIG_SYS_PCI_MEMBASE. UART / SERIAL @@ -73,7 +73,7 @@ UART / SERIAL The UART port works fine when an external serial clock is provided (like the one on the Ebony board) and when using internal clocking. -This is controlled with the CFG_EXT_SERIAL_CLOCK flag. When using +This is controlled with the CONFIG_SYS_EXT_SERIAL_CLOCK flag. When using internal clocking, the "ideal baud rate" settings in the 440GP user manual are automatically calculated. @@ -94,7 +94,7 @@ cause problems when a probe (read) is performed (for example the CDCV850 clock controller at address 0x69 on the ebony board). To prevent probing certain addresses you can define the -CFG_I2C_NOPROBES macro in your board-specific header file. When +CONFIG_SYS_I2C_NOPROBES macro in your board-specific header file. When defined, all specified addresses are skipped during a probe. The addresses that are skipped will be displayed in the output of the iprobe command. @@ -102,12 +102,12 @@ of the iprobe command. For example, to prevent probing address 0x69, define the macro as follows: -#define CFG_I2C_NOPROBES {0x69} +#define CONFIG_SYS_I2C_NOPROBES {0x69} Similarly, to prevent probing addresses 0x69 and 0x70, define the macro a: -#define CFG_I2C_NOPROBES {0x69, 0x70} +#define CONFIG_SYS_I2C_NOPROBES {0x69, 0x70} DDR SDRAM CONTROLLER @@ -144,7 +144,7 @@ utilities once you get to the U-Boot command prompt. NOTE: the default The cpu-specific code sets up a default pci_controller structure that maps in a single PCI I/O space and PCI memory space. The I/O space begins at PCI I/O address 0 and the PCI memory space is -256 MB starting at PCI address CFG_PCI_TARGBASE. After the +256 MB starting at PCI address CONFIG_SYS_PCI_TARGBASE. After the pci_controller structure is initialized, the cpu-specific code will call the routine pci_pre_init(). This routine is implemented by board-specific code & is where the board can over-ride/extend the @@ -157,7 +157,7 @@ initialization continues. The default 440GP PCI target configuration is minimal -- it assumes that the strapping registers are set as necessary. Since the strapping bits provide very limited flexibility, you may want to customize the boards -target configuration. If CFG_PCI_TARGET_INIT is defined, the cpu-specific +target configuration. If CONFIG_SYS_PCI_TARGET_INIT is defined, the cpu-specific code will call the routine pci_target_init() which you must implement in your board-specific code. @@ -166,7 +166,7 @@ initializing the subsystem id and subsystem vendor id, and then ensuring that the 'enable host configuration' bit in the PCIX0_BRDGOPT2 is set. The default PCI master initialization maps in 256 MB of pci memory -starting at PCI address CFG_PCI_MEMBASE. To customize this, define +starting at PCI address CONFIG_SYS_PCI_MEMBASE. To customize this, define PCI_MASTER_INIT. This will call the routine pci_master_init() in your board-specific code rather than performing the default master initialization. |