diff options
Diffstat (limited to 'cpu/mcf52x2/cpu_init.c')
| -rw-r--r-- | cpu/mcf52x2/cpu_init.c | 92 |
1 files changed, 72 insertions, 20 deletions
diff --git a/cpu/mcf52x2/cpu_init.c b/cpu/mcf52x2/cpu_init.c index 5736d0f26..f41d77bc5 100644 --- a/cpu/mcf52x2/cpu_init.c +++ b/cpu/mcf52x2/cpu_init.c @@ -6,6 +6,10 @@ * (C) Copyright 2005 * BuS Elektronik GmbH & Co. KG <esw@bus-elektronik.de> * + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + * Hayden Fraser (Hayden.Fraser@freescale.com) + * * See file CREDITS for list of people who contributed to this * project. * @@ -29,6 +33,74 @@ #include <watchdog.h> #include <asm/immap.h> +#if defined(CONFIG_M5253) +/* + * Breath some life into the CPU... + * + * Set up the memory map, + * initialize a bunch of registers, + * initialize the UPM's + */ +void cpu_init_f(void) +{ + mbar_writeByte(MCFSIM_MPARK, 0x40); /* 5249 Internal Core takes priority over DMA */ + mbar_writeByte(MCFSIM_SYPCR, 0x00); + mbar_writeByte(MCFSIM_SWIVR, 0x0f); + mbar_writeByte(MCFSIM_SWSR, 0x00); + mbar_writeByte(MCFSIM_SWDICR, 0x00); + mbar_writeByte(MCFSIM_TIMER1ICR, 0x00); + mbar_writeByte(MCFSIM_TIMER2ICR, 0x88); + mbar_writeByte(MCFSIM_I2CICR, 0x00); + mbar_writeByte(MCFSIM_UART1ICR, 0x00); + mbar_writeByte(MCFSIM_UART2ICR, 0x00); + mbar_writeByte(MCFSIM_ICR6, 0x00); + mbar_writeByte(MCFSIM_ICR7, 0x00); + mbar_writeByte(MCFSIM_ICR8, 0x00); + mbar_writeByte(MCFSIM_ICR9, 0x00); + mbar_writeByte(MCFSIM_QSPIICR, 0x00); + + mbar2_writeLong(MCFSIM_GPIO_INT_EN, 0x00000080); + mbar2_writeByte(MCFSIM_INTBASE, 0x40); /* Base interrupts at 64 */ + mbar2_writeByte(MCFSIM_SPURVEC, 0x00); + + /*mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020); *//* Enable a 1 cycle pre-drive cycle on CS1 */ + + /* + * Setup chip selects... + */ + + mbar_writeShort(MCFSIM_CSAR1, CFG_CSAR1); + mbar_writeShort(MCFSIM_CSCR1, CFG_CSCR1); + mbar_writeLong(MCFSIM_CSMR1, CFG_CSMR1); + + mbar_writeShort(MCFSIM_CSAR0, CFG_CSAR0); + mbar_writeShort(MCFSIM_CSCR0, CFG_CSCR0); + mbar_writeLong(MCFSIM_CSMR0, CFG_CSMR0); + + /* enable instruction cache now */ + icache_enable(); +} + +/*initialize higher level parts of CPU like timers */ +int cpu_init_r(void) +{ + return (0); +} + +void uart_port_conf(void) +{ + /* Setup Ports: */ + switch (CFG_UART_PORT) { + case 0: + break; + case 1: + break; + case 2: + break; + } +} +#endif /* #if defined(CONFIG_M5253) */ + #if defined(CONFIG_M5271) void cpu_init_f(void) { @@ -394,26 +466,6 @@ void uart_port_conf(void) */ void cpu_init_f(void) { -#ifndef CFG_PLL_BYPASS - /* - * Setup the PLL to run at the specified speed - * - */ - volatile unsigned long cpll = mbar2_readLong(MCFSIM_PLLCR); - unsigned long pllcr; -#ifdef CFG_FAST_CLK - pllcr = 0x925a3100; /* ~140MHz clock (PLL bypass = 0) */ -#else - pllcr = 0x135a4140; /* ~72MHz clock (PLL bypass = 0) */ -#endif - cpll = cpll & 0xfffffffe; /* Set PLL bypass mode = 0 (PSTCLK = crystal) */ - mbar2_writeLong(MCFSIM_PLLCR, cpll); /* Set the PLL to bypass mode (PSTCLK = crystal) */ - mbar2_writeLong(MCFSIM_PLLCR, pllcr); /* set the clock speed */ - pllcr ^= 0x00000001; /* Set pll bypass to 1 */ - mbar2_writeLong(MCFSIM_PLLCR, pllcr); /* Start locking (pll bypass = 1) */ - udelay(0x20); /* Wait for a lock ... */ -#endif /* #ifndef CFG_PLL_BYPASS */ - /* * NOTE: by setting the GPIO_FUNCTION registers, we ensure that the UART pins * (UART0: gpio 30,27, UART1: gpio 31, 28) will be used as UART pins |