MPC824x: remove obsolete "PN62" board

The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade.  It is now
causing build issues.  Instead of wasting time on things nobody is
interested in any more, we rather drop this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>

1 files changed, 0 insertions, 285 deletions

diff --git a/include/configs/PN62.h b/include/configs/PN62.h
deleted file mode 100644
index 2a82f94b6..000000000
--- a/include/configs/PN62.h
+++ /dev/null
@@ -1,285 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC824X		1
-#define CONFIG_MPC8240		1
-#define CONFIG_PN62		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define CONFIG_CONS_INDEX	1
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BSP
-
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_SOURCE
-
-
-#define CONFIG_BAUDRATE		19200	/* console baudrate		*/
-
-#define CONFIG_BOOTDELAY	1	/* autoboot after n seconds	*/
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_SERVERIP		10.0.0.201
-#define CONFIG_IPADDR		10.0.0.200
-#define CONFIG_ROOTPATH		"/opt/eldk/ppc_82xx"
-#define CONFIG_NETMASK		255.255.255.0
-#undef CONFIG_BOOTARGS
-#if 0
-/* Boot Linux with NFS root filesystem */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify y;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 100000; bootm"
-			/* "tftpboot 100000 uImage; bootm" */
-#else
-/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify n;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/ram rw " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 200000; bootm"
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
-
-#define CONFIG_PRAM		1024		/* reserve 1 MB protected RAM	*/
-
-#define CONFIG_MISC_INIT_R	1		/* call misc_init_r() on init	*/
-
-#define CONFIG_HAS_ETH1		1		/* add support for eth1addr	*/
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1		/* Show boot progress on LEDs   */
-
-/*
- * PCI stuff
- */
-#define CONFIG_PCI				/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP				/* we need Plug 'n Play		*/
-#if 0
-#define CONFIG_PCI_SCAN_SHOW			/* show PCI auto-scan at boot	*/
-#endif
-
-/*
- * Networking stuff
- */
-
-#define CONFIG_PCNET				/* there are 2 AMD PCnet 79C973	*/
-#define CONFIG_PCNET_79C973
-
-#define _IO_BASE		0xfe000000	/* points to PCI I/O space	*/
-
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	0x10000000
-
-#define CONFIG_SYS_RESET_ADDRESS	0xfff00100
-
-#undef	CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN		0x00030000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-
-#define CONFIG_SYS_NO_FLASH		1		/* There is no FLASH memory	*/
-
-#define CONFIG_ENV_IS_NOWHERE	1		/* Store ENV in memory only	*/
-#define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x01f00000	/* 0 ... 32 MB in DRAM		*/
-
-/*
- * Serial port configuration
- */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#define CONFIG_SYS_NS16550_CLK		1843200
-
-#define CONFIG_SYS_NS16550_COM1	0xff800008
-#define CONFIG_SYS_NS16550_COM2	0xff800000
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER  3
-
-#define CONFIG_SYS_EUMB_ADDR		0xFCE00000
-
-/* MCCR1 */
-#define CONFIG_SYS_ROMNAL		3	/* rom/flash next access time		*/
-#define CONFIG_SYS_ROMFAL		7	/* rom/flash access time		*/
-
-/* MCCR2 */
-#define CONFIG_SYS_ASRISE		6	/* ASRISE in clocks			*/
-#define CONFIG_SYS_ASFALL		12	/* ASFALL in clocks			*/
-#define CONFIG_SYS_REFINT		5600	/* REFINT in clocks			*/
-
-/* MCCR3 */
-#define CONFIG_SYS_BSTOPRE		0x3cf	/* Burst To Precharge			*/
-#define CONFIG_SYS_REFREC		2	/* Refresh to activate interval		*/
-#define CONFIG_SYS_RDLAT		3	/* data latency from read command	*/
-
-/* MCCR4 */
-#define CONFIG_SYS_PRETOACT		1	/* Precharge to activate interval	*/
-#define CONFIG_SYS_ACTTOPRE		3	/* Activate to Precharge interval	*/
-#define CONFIG_SYS_ACTORW		2	/* Activate to R/W			*/
-#define CONFIG_SYS_SDMODE_CAS_LAT	2	/* SDMODE CAS latency			*/
-#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE Wrap type			*/
-#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* SDMODE Burst length 2=4, 3=8		*/
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
-
-/* Memory bank settings:
- *
- * only bits 20-29 are actually used from these vales to set the
- * start/qend address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START		0x00000000
-#define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE	1
-#define CONFIG_SYS_BANK1_START		0x00000000
-#define CONFIG_SYS_BANK1_END		0x00000000
-#define CONFIG_SYS_BANK1_ENABLE	0
-#define CONFIG_SYS_BANK2_START		0x00000000
-#define CONFIG_SYS_BANK2_END		0x00000000
-#define CONFIG_SYS_BANK2_ENABLE	0
-#define CONFIG_SYS_BANK3_START		0x00000000
-#define CONFIG_SYS_BANK3_END		0x00000000
-#define CONFIG_SYS_BANK3_ENABLE	0
-#define CONFIG_SYS_BANK4_START		0x00000000
-#define CONFIG_SYS_BANK4_END		0x00000000
-#define CONFIG_SYS_BANK4_ENABLE	0
-#define CONFIG_SYS_BANK5_START		0x00000000
-#define CONFIG_SYS_BANK5_END		0x00000000
-#define CONFIG_SYS_BANK5_ENABLE	0
-#define CONFIG_SYS_BANK6_START		0x00000000
-#define CONFIG_SYS_BANK6_END		0x00000000
-#define CONFIG_SYS_BANK6_ENABLE	0
-#define CONFIG_SYS_BANK7_START		0x00000000
-#define CONFIG_SYS_BANK7_END		0x00000000
-#define CONFIG_SYS_BANK7_ENABLE	0
-
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- * are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE		0x01
-
-#define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
-					/* see 8240 book for bit definitions	*/
-#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
-					/* currently accessed page in memory	*/
-					/* see 8240 book for details		*/
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* PCI memory space */
-#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Config addrs, etc */
-#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-#endif	/* __CONFIG_H */