mpc83xx: Add MPC8360EMDS basic board support

Add support for the Freescale MPC8360EMDS board.
Includes DDR, DUART, Local Bus, PCI.

1 files changed, 151 insertions, 153 deletions

diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c
index 3dfde8ac0..acc8c9e79 100644
--- a/cpu/mpc83xx/spd_sdram.c
+++ b/cpu/mpc83xx/spd_sdram.c
@@ -4,7 +4,7 @@
  * (C) Copyright 2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright (C) 2004-2006 Freescale Semiconductor, Inc.
  * (C) Copyright 2003 Motorola Inc.
  * Xianghua Xiao (X.Xiao@motorola.com)
  *
@@ -112,14 +112,10 @@ static void spd_debug(spd_eeprom_t *spd)
 
 long int spd_sdram()
 {
-#ifdef CONFIG_MPC834X
-	int caslat_83xx;  /* For Errata DDR6 */
-#endif
 	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
 	volatile ddr83xx_t *ddr = &immap->ddr;
 	volatile law83xx_t *ecm = &immap->sysconf.ddrlaw[0];
 	spd_eeprom_t spd;
-	unsigned int tmp, tmp1;
 	unsigned int memsize;
 	unsigned int law_size;
 	unsigned char caslat, caslat_ctrl;
@@ -131,28 +127,7 @@ long int spd_sdram()
 	unsigned sdram_cfg;
 	unsigned int ddrc_ecc_enable;
 
-
         /* Read SPD parameters with I2C */
-#ifdef CFG_83XX_DDR_USES_CS0
-	ddr->csbnds[0].csbnds = (banksize(spd.row_dens) >> 24) - 1;
-	ddr->cs_config[0] = ( 1 << 31
-			    | (spd.nrow_addr - 12) << 8
-			    | (spd.ncol_addr - 8) );
-	debug("\n");
-	debug("cs0_bnds = 0x%08x\n",ddr->csbnds[0].csbnds);
-	debug("cs0_config = 0x%08x\n",ddr->cs_config[0]);
-
-	if (spd.nrows == 2) {
-		ddr->csbnds[1].csbnds = ( (banksize(spd.row_dens) >> 8)
-				  | ((banksize(spd.row_dens) >> 23) - 1) );
-		ddr->cs_config[1] = ( 1<<31
-				    | (spd.nrow_addr-12) << 8
-				    | (spd.ncol_addr-8) );
-		debug("cs1_bnds = 0x%08x\n",ddr->csbnds[1].csbnds);
-		debug("cs1_config = 0x%08x\n",ddr->cs_config[1]);
-	}
-
-#else
 	CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd));
 #ifdef SPD_DEBUG
 	spd_debug(&spd);
@@ -183,6 +158,26 @@ long int spd_sdram()
 		return 0;
 	}
         /* Setup DDR chip select register */
+#ifdef CFG_83XX_DDR_USES_CS0
+	ddr->csbnds[0].csbnds = (banksize(spd.row_dens) >> 24) - 1;
+	ddr->cs_config[0] = ( 1 << 31
+			    | (spd.nrow_addr - 12) << 8
+			    | (spd.ncol_addr - 8) );
+	debug("\n");
+	debug("cs0_bnds = 0x%08x\n",ddr->csbnds[0].csbnds);
+	debug("cs0_config = 0x%08x\n",ddr->cs_config[0]);
+
+	if (spd.nrows == 2) {
+		ddr->csbnds[1].csbnds = ( (banksize(spd.row_dens) >> 8)
+				  | ((banksize(spd.row_dens) >> 23) - 1) );
+		ddr->cs_config[1] = ( 1<<31
+				    | (spd.nrow_addr-12) << 8
+				    | (spd.ncol_addr-8) );
+		debug("cs1_bnds = 0x%08x\n",ddr->csbnds[1].csbnds);
+		debug("cs1_config = 0x%08x\n",ddr->cs_config[1]);
+	}
+
+#else
 	ddr->csbnds[2].csbnds = (banksize(spd.row_dens) >> 24) - 1;
 	ddr->cs_config[2] = ( 1 << 31
 			    | (spd.nrow_addr - 12) << 8
@@ -243,8 +238,9 @@ long int spd_sdram()
 	 */
 	caslat = __ilog2(spd.cas_lat);
 
-	if (caslat > 4 ) {
-		printf("DDR: Invalid SPD CAS Latency, caslat=%02X\n", caslat);
+	if (caslat > 6 ) {
+		printf("DDR: Invalid SPD CAS Latency, caslat=%02X\n",
+			spd.cas_lat);
 		return 0;
 	}
 	max_bus_clk = 1000 *10 / (((spd.clk_cycle & 0xF0) >> 4) * 10
@@ -256,89 +252,110 @@ long int spd_sdram()
 	ddrc_clk = get_ddr_clk(0) / 1000000;
 
 	if (max_data_rate >= 390) { /* it is DDR 400 */
-		printf("DDR: platform not support DDR 400\n");
-		return 0;
+		if (ddrc_clk <= 410 && ddrc_clk > 350) {
+			/* DDR controller clk at 350~410 */
+			effective_data_rate = 400; /* 5ns */
+			caslat = caslat;
+		} else if (ddrc_clk <= 350 && ddrc_clk > 280) {
+			/* DDR controller clk at 280~350 */
+			effective_data_rate = 333; /* 6ns */
+			if (spd.clk_cycle2 == 0x60) {
+				caslat = caslat - 1;
+			} else {
+				caslat = caslat;
+			}
+		} else if (ddrc_clk <= 280 && ddrc_clk > 230) {
+			/* DDR controller clk at 230~280 */
+			effective_data_rate = 266; /* 7.5ns */
+			if (spd.clk_cycle3 == 0x75) {
+				caslat = caslat - 2;
+			} else if (spd.clk_cycle2 == 0x60) {
+				caslat = caslat - 1;
+			} else {
+				caslat = caslat;
+			}
+		} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+			/* DDR controller clk at 90~230 */
+			effective_data_rate = 200; /* 10ns */
+			if (spd.clk_cycle3 == 0x75) {
+				caslat = caslat - 2;
+			} else if (spd.clk_cycle2 == 0x60) {
+				caslat = caslat - 1;
+			} else {
+				caslat = caslat;
+			}
+		}
 	} else if (max_data_rate >= 323) { /* it is DDR 333 */
 		if (ddrc_clk <= 350 && ddrc_clk > 280) {
-			/* DDRC clk at 280~350 */
+			/* DDR controller clk at 280~350 */
 			effective_data_rate = 333; /* 6ns */
 			caslat = caslat;
 		} else if (ddrc_clk <= 280 && ddrc_clk > 230) {
-			/* DDRC clk at 230~280 */
+			/* DDR controller clk at 230~280 */
+			effective_data_rate = 266; /* 7.5ns */
 			if (spd.clk_cycle2 == 0x75) {
-				effective_data_rate = 266; /* 7.5ns */
 				caslat = caslat - 1;
+			} else {
+				caslat = caslat;
 			}
 		} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
-			/* DDRC clk at 90~230 */
+			/* DDR controller clk at 90~230 */
+			effective_data_rate = 200; /* 10ns */
 			if (spd.clk_cycle3 == 0xa0) {
-				effective_data_rate = 200; /* 10ns */
 				caslat = caslat - 2;
+			} else if (spd.clk_cycle2 == 0x75) {
+				caslat = caslat - 1;
+			} else {
+				caslat = caslat;
 			}
 		}
 	} else if (max_data_rate >= 256) { /* it is DDR 266 */
 		if (ddrc_clk <= 350 && ddrc_clk > 280) {
-			/* DDRC clk at 280~350 */
+			/* DDR controller clk at 280~350 */
 			printf("DDR: DDR controller freq is more than "
 				"max data rate of the module\n");
 			return 0;
 		} else if (ddrc_clk <= 280 && ddrc_clk > 230) {
-			/* DDRC clk at 230~280 */
+			/* DDR controller clk at 230~280 */
 			effective_data_rate = 266; /* 7.5ns */
 			caslat = caslat;
 		} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
-			/* DDRC clk at 90~230 */
+			/* DDR controller clk at 90~230 */
+			effective_data_rate = 200; /* 10ns */
 			if (spd.clk_cycle2 == 0xa0) {
-				effective_data_rate = 200; /* 10ns */
 				caslat = caslat - 1;
 			}
 		}
 	} else if (max_data_rate >= 190) { /* it is DDR 200 */
 		if (ddrc_clk <= 350 && ddrc_clk > 230) {
-			/* DDRC clk at 230~350 */
+			/* DDR controller clk at 230~350 */
 			printf("DDR: DDR controller freq is more than "
 				"max data rate of the module\n");
 			return 0;
 		} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
-			/* DDRC clk at 90~230 */
+			/* DDR controller clk at 90~230 */
 			effective_data_rate = 200; /* 10ns */
 			caslat = caslat;
 		}
 	}
 
-#ifdef CONFIG_MPC834X
-/* Errata DDR6
-   This errata affects all MPC8349E, MPC8343E and MPC8347E processors.
-*/
-	if ((tmp1 >= 280) && (tmp1 < 350)) /* CSB=333 */
-	{
-		if (spd.mid[0] == 0x2c) {
-			/* Micron memory running at 333 MHz */
-			/* Chances are, U-Boot will crash before we get here,
-			   but just in case, display a message and return error. */
-			printf("Micron DDR not supported at 333MHz CSB\n");
-			return 0;
-		} else if (spd.mid[0] == 0xad) {
-			printf("Hynix DDR does not require Errata DDR6\n");
-		} else {
-			/* enable 2 cycle Earlier for CL=2.5 or 3 */
-			ddr->debug_reg = 0x202c0000;
-			printf("Errata DDR6 (debug_reg=0x%x)\n", ddr->debug_reg);
-		}
-		caslat_83xx = caslat;
-	}
-
-	if ((tmp1 >= 230) && (tmp1 < 280)) {  /* CSB=266 */
-		if (spd.mid[0] != 0x2c) /* non-Micron */
-			caslat_83xx = caslat - 1;
+	debug("DDR:Effective data rate is: %dMhz\n", effective_data_rate);
+	debug("DDR:The MSB 1 of CAS Latency is: %d\n", caslat);
 
+	/*
+	 * Errata DDR6 work around: input enable 2 cycles earlier.
+	 * including MPC834x Rev1.0/1.1 and MPC8360 Rev1.1/1.2.
+	 */
+	if (caslat == 2) {
+		ddr->debug_reg = 0x201c0000; /* CL=2 */
+	} else if (caslat == 3) {
+		ddr->debug_reg = 0x202c0000; /* CL=2.5 */
+	} else if (caslat == 4) {
+		ddr->debug_reg = 0x202c0000; /* CL=3.0 */
 	}
+	__asm__ __volatile__ ("sync");
 
-	if ((tmp1 >= 90) && (tmp1 < 230)) {  /* CSB=200 */
-		caslat = 3;
-		caslat_83xx = 2;
-	}
-#endif
+	debug("Errata DDR6 (debug_reg=0x%08x)\n", ddr->debug_reg);
 
 	/*
 	 * note: caslat must also be programmed into ddr->sdram_mode
@@ -353,11 +370,7 @@ long int spd_sdram()
 	    (((picos_to_clk(spd.trp * 250) & 0x07) << 28 ) |
 	     ((picos_to_clk(spd.tras * 1000) & 0x0f ) << 24 ) |
 	     ((picos_to_clk(spd.trcd * 250) & 0x07) << 20 ) |
-#ifdef CONFIG_MPC834x
-	     ((caslat_83xx & 0x07) << 16 ) |
-#else
 	     ((caslat_ctrl & 0x07) << 16 ) |
-#endif
 	     (((picos_to_clk(spd.trfc * 1000) - 8) & 0x0f) << 12 ) |
 	     ( 0x300 ) |
 	     ((picos_to_clk(spd.trrd * 250) & 0x07) << 4) | 1);
@@ -370,13 +383,10 @@ long int spd_sdram()
 	ddr->sdram_cfg = 0x42000000;
 
 	/* Check DIMM data bus width */
-	if (spd.dataw_lsb == 0x20)
-	{
+	if (spd.dataw_lsb == 0x20) {
 		burstlen = 0x03; /* 32 bit data bus, burst len is 8 */
 		printf("\n   DDR DIMM: data bus width is 32 bit");
-	}
-	else
-	{
+	} else {
 		burstlen = 0x02; /* Others act as 64 bit bus, burst len is 4 */
 		printf("\n   DDR DIMM: data bus width is 64 bit");
 	}
@@ -384,68 +394,67 @@ long int spd_sdram()
 	/* Is this an ECC DDR chip? */
 	if (spd.config == 0x02) {
 		printf(" with ECC\n");
-	}
-	else
+	} else {
 		printf(" without ECC\n");
+	}
 
 	/* Burst length is always 4 for 64 bit data bus, 8 for 32 bit data bus,
 	   Burst type is sequential
 	 */
-	switch(caslat) {
-	case 1:
-		ddr->sdram_mode = 0x50 | burstlen; /* CL=1.5 */
-		break;
-	case 2:
-		ddr->sdram_mode = 0x20 | burstlen; /* CL=2.0 */
-		break;
-	case 3:
-		ddr->sdram_mode = 0x60 | burstlen; /* CL=2.5 */
-		break;
-	case 4:
-		ddr->sdram_mode = 0x30 | burstlen; /* CL=3.0 */
-		break;
-	default:
-		printf("DDR:only CAS Latency 1.5, 2.0, 2.5, 3.0 "
-					"is supported.\n");
-		return 0;
+	switch (caslat) {
+		case 1:
+			ddr->sdram_mode = 0x50 | burstlen; /* CL=1.5 */
+			break;
+		case 2:
+			ddr->sdram_mode = 0x20 | burstlen; /* CL=2.0 */
+			break;
+		case 3:
+			ddr->sdram_mode = 0x60 | burstlen; /* CL=2.5 */
+			break;
+		case 4:
+			ddr->sdram_mode = 0x30 | burstlen; /* CL=3.0 */
+			break;
+		default:
+			printf("DDR:only CL 1.5, 2.0, 2.5, 3.0 is supported\n");
+			return 0;
 	}
 	debug("DDR:sdram_mode=0x%08x\n", ddr->sdram_mode);
 
-	switch(spd.refresh) {
-	case 0x00:
-	case 0x80:
-		tmp = picos_to_clk(15625000);
-		break;
-	case 0x01:
-	case 0x81:
-		tmp = picos_to_clk(3900000);
-		break;
-	case 0x02:
-	case 0x82:
-		tmp = picos_to_clk(7800000);
-		break;
-	case 0x03:
-	case 0x83:
-		tmp = picos_to_clk(31300000);
-		break;
-	case 0x04:
-	case 0x84:
-		tmp = picos_to_clk(62500000);
-		break;
-	case 0x05:
-	case 0x85:
-		tmp = picos_to_clk(125000000);
-		break;
-	default:
-		tmp = 0x512;
-		break;
+	switch (spd.refresh) {
+		case 0x00:
+		case 0x80:
+			refresh_clk = picos_to_clk(15625000);
+			break;
+		case 0x01:
+		case 0x81:
+			refresh_clk = picos_to_clk(3900000);
+			break;
+		case 0x02:
+		case 0x82:
+			refresh_clk = picos_to_clk(7800000);
+			break;
+		case 0x03:
+		case 0x83:
+			refresh_clk = picos_to_clk(31300000);
+			break;
+		case 0x04:
+		case 0x84:
+			refresh_clk = picos_to_clk(62500000);
+			break;
+		case 0x05:
+		case 0x85:
+			refresh_clk = picos_to_clk(125000000);
+			break;
+		default:
+			refresh_clk = 0x512;
+			break;
 	}
 
 	/*
 	 * Set BSTOPRE to 0x100 for page mode
 	 * If auto-charge is used, set BSTOPRE = 0
 	 */
-	ddr->sdram_interval = ((tmp & 0x3fff) << 16) | 0x100;
+	ddr->sdram_interval = ((refresh_clk & 0x3fff) << 16) | 0x100;
 	debug("DDR:sdram_interval=0x%08x\n", ddr->sdram_interval);
 
 	/* SS_EN = 0, source synchronous disable
@@ -459,8 +468,8 @@ long int spd_sdram()
 	udelay(600);
 
 	/*
-	 * Figure out the settings for the sdram_cfg register.  Build up
-	 * the entire register in 'tmp' before writing since the write into
+	 * Figure out the settings for the sdram_cfg register. Build up
+	 * the value in 'sdram_cfg' before writing since the write into
 	 * the register will actually enable the memory controller, and all
 	 * settings must be done before enabling.
 	 *
@@ -493,13 +502,13 @@ long int spd_sdram()
 		/* set single bit error threshold to maximum value,
 		 * reset counter to zero */
 		ddr->err_sbe = (255 << ECC_ERROR_MAN_SBET_SHIFT) |
-			(0 << ECC_ERROR_MAN_SBEC_SHIFT);
+				(0 << ECC_ERROR_MAN_SBEC_SHIFT);
 	}
 
 	debug("DDR:err_disable=0x%08x\n", ddr->err_disable);
 	debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe);
 #endif
-	printf("   DDRC ECC mode: %s", ddrc_ecc_enable ? "ON":"OFF");
+	printf("   DDRC ECC mode: %s\n", ddrc_ecc_enable ? "ON":"OFF");
 
 #if defined(CONFIG_DDR_2T_TIMING)
 	/*
@@ -517,7 +526,6 @@ long int spd_sdram()
 }
 #endif /* CONFIG_SPD_EEPROM */
 
-
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
 /*
  * Use timebase counter, get_timer() is not availabe
@@ -602,26 +610,16 @@ void ddr_enable_ecc(unsigned int dram_size)
 		}
 	}
 
-	/* 8K */
-	dma_xfer((uint *)0x2000, 0x2000, (uint *)0);
-	/* 16K */
-	dma_xfer((uint *)0x4000, 0x4000, (uint *)0);
-	/* 32K */
-	dma_xfer((uint *)0x8000, 0x8000, (uint *)0);
-	/* 64K */
-	dma_xfer((uint *)0x10000, 0x10000, (uint *)0);
-	/* 128k */
-	dma_xfer((uint *)0x20000, 0x20000, (uint *)0);
-	/* 256k */
-	dma_xfer((uint *)0x40000, 0x40000, (uint *)0);
-	/* 512k */
-	dma_xfer((uint *)0x80000, 0x80000, (uint *)0);
-	/* 1M */
-	dma_xfer((uint *)0x100000, 0x100000, (uint *)0);
-	/* 2M */
-	dma_xfer((uint *)0x200000, 0x200000, (uint *)0);
-	/* 4M */
-	dma_xfer((uint *)0x400000, 0x400000, (uint *)0);
+	dma_xfer((uint *)0x2000, 0x2000, (uint *)0); /* 8K */
+	dma_xfer((uint *)0x4000, 0x4000, (uint *)0); /* 16K */
+	dma_xfer((uint *)0x8000, 0x8000, (uint *)0); /* 32K */
+	dma_xfer((uint *)0x10000, 0x10000, (uint *)0); /* 64K */
+	dma_xfer((uint *)0x20000, 0x20000, (uint *)0); /* 128K */
+	dma_xfer((uint *)0x40000, 0x40000, (uint *)0); /* 256K */
+	dma_xfer((uint *)0x80000, 0x80000, (uint *)0); /* 512K */
+	dma_xfer((uint *)0x100000, 0x100000, (uint *)0); /* 1M */
+	dma_xfer((uint *)0x200000, 0x200000, (uint *)0); /* 2M */
+	dma_xfer((uint *)0x400000, 0x400000, (uint *)0); /* 4M */
 
 	for (i = 1; i < dram_size / 0x800000; i++) {
 		dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);