General help message cleanup

Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.

Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.

This patch cleans this up - for example:

Before:
	=> help dtt
	dtt - Digital Thermometer and Thermostat

	Usage:
	dtt         - Read temperature from digital thermometer and thermostat.

After:
	=> help dtt
	dtt - Read temperature from Digital Thermometer and Thermostat

	Usage:
	dtt

Signed-off-by: Wolfgang Denk <wd@denx.de>

1 files changed, 6 insertions, 6 deletions

diff --git a/board/trab/cmd_trab.c b/board/trab/cmd_trab.c
index 7e2a67234..d0465fb7e 100644
--- a/board/trab/cmd_trab.c
+++ b/board/trab/cmd_trab.c
@@ -262,7 +262,7 @@ U_BOOT_CMD(
 	"\n"
 	"    -  start burn-in test application\n"
 	"       The burn-in test could took a while to finish!\n"
-	"       The content of the onboard EEPROM is modified!\n"
+	"       The content of the onboard EEPROM is modified!"
 );
 
 
@@ -295,7 +295,7 @@ U_BOOT_CMD(
 	"read dip switch on TRAB",
 	"\n"
 	"    - read state of dip switch (S1) on TRAB board\n"
-	"      read sequence: 1-2-3-4; ON=1; OFF=0; e.g.: \"0100\"\n"
+	"      read sequence: 1-2-3-4; ON=1; OFF=0; e.g.: \"0100\""
 );
 
 
@@ -323,7 +323,7 @@ U_BOOT_CMD(
 	vcc5v,	1,	1,	do_vcc5v,
 	"read VCC5V on TRAB",
 	"\n"
-	"    - read actual value of voltage VCC5V\n"
+	"    - read actual value of voltage VCC5V"
 );
 
 
@@ -347,7 +347,7 @@ int do_contact_temp (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 U_BOOT_CMD(
 	c_temp,	1,	1,	do_contact_temp,
 	"read contact temperature on TRAB",
-	"\n"
+	""
 	"    -  reads the onboard temperature (=contact temperature)\n"
 );
 
@@ -401,7 +401,7 @@ U_BOOT_CMD(
 	"print burn in status on TRAB",
 	"\n"
 	"    -  prints the status variables of the last burn in test\n"
-	"       stored in the onboard EEPROM on TRAB board\n"
+	"       stored in the onboard EEPROM on TRAB board"
 );
 
 static int read_dip (void)
@@ -890,7 +890,7 @@ U_BOOT_CMD(
 	"delay\n"
 	"    - contact temperature [1/100 C] is printed endlessly to console\n"
 	"      <delay> specifies the seconds to wait between two measurements\n"
-	"      For each measurment a timestamp is printeted\n"
+	"      For each measurment a timestamp is printeted"
 );
 
 #endif