Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

32 files changed, 396 insertions, 40 deletions

diff --git a/arch/powerpc/cpu/mpc83xx/pcie.c b/arch/powerpc/cpu/mpc83xx/pcie.c
index 09970b058..28c25e5fe 100644
--- a/arch/powerpc/cpu/mpc83xx/pcie.c
+++ b/arch/powerpc/cpu/mpc83xx/pcie.c
@@ -299,6 +299,8 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
 
 	printf("PCIE%d: ", bus);
 
+#define PCI_LTSSM	0x404 /* PCIe Link Training, Status State Machine */
+#define PCI_LTSSM_L0	0x16 /* L0 state */
 	reg16 = in_le16(hose_cfg_base + PCI_LTSSM);
 	if (reg16 >= PCI_LTSSM_L0)
 		printf("link\n");
diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index 0d1e8f1f0..f70f0d747 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -46,6 +46,7 @@ COBJS-$(CONFIG_MPC8568) += ddr-gen2.o
 COBJS-$(CONFIG_MPC8544) += ddr-gen2.o
 
 # supports ddr1/2/3
+COBJS-$(CONFIG_PPC_C29X)	+= ddr-gen3.o
 COBJS-$(CONFIG_MPC8572) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8536) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8569)	+= ddr-gen3.o
@@ -100,6 +101,7 @@ COBJS-$(CONFIG_SYS_FSL_QORIQ_CHASSIS1) += fsl_corenet_serdes.o
 COBJS-$(CONFIG_SYS_FSL_QORIQ_CHASSIS2) += fsl_corenet2_serdes.o
 
 # SoC specific SERDES support
+COBJS-$(CONFIG_PPC_C29X)	+= c29x_serdes.o
 COBJS-$(CONFIG_MPC8536) += mpc8536_serdes.o
 COBJS-$(CONFIG_MPC8544) += mpc8544_serdes.o
 COBJS-$(CONFIG_MPC8548) += mpc8548_serdes.o
diff --git a/arch/powerpc/cpu/mpc85xx/b4860_ids.c b/arch/powerpc/cpu/mpc85xx/b4860_ids.c
index 53c6a7faf..39b8e3ecc 100644
--- a/arch/powerpc/cpu/mpc85xx/b4860_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/b4860_ids.c
@@ -41,8 +41,8 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
 
 #ifdef CONFIG_SYS_SRIO
 struct srio_liodn_id_table srio_liodn_tbl[] = {
-	SET_SRIO_LIODN_1(1, 307),
-	SET_SRIO_LIODN_1(2, 387),
+	SET_SRIO_LIODN_BASE(1, 307),
+	SET_SRIO_LIODN_BASE(2, 387),
 };
 int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
 #endif
@@ -112,10 +112,10 @@ int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
 #ifdef CONFIG_SYS_DPAA_RMAN
 struct liodn_id_table rman_liodn_tbl[] = {
 	/* Set RMan block 0-3 liodn offset */
-	SET_RMAN_LIODN(0, 678),
-	SET_RMAN_LIODN(1, 679),
-	SET_RMAN_LIODN(2, 680),
-	SET_RMAN_LIODN(3, 681),
+	SET_RMAN_LIODN(0, 6),
+	SET_RMAN_LIODN(1, 7),
+	SET_RMAN_LIODN(2, 8),
+	SET_RMAN_LIODN(3, 9),
 };
 int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl);
 #endif
diff --git a/arch/powerpc/cpu/mpc85xx/c29x_serdes.c b/arch/powerpc/cpu/mpc85xx/c29x_serdes.c
new file mode 100644
index 000000000..51972cb7c
--- /dev/null
+++ b/arch/powerpc/cpu/mpc85xx/c29x_serdes.c
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_serdes.h>
+
+#define SRDS1_MAX_LANES		4
+
+static u32 serdes1_prtcl_map;
+
+struct serdes_config {
+	u32 protocol;
+	u8 lanes[SRDS1_MAX_LANES];
+};
+
+static const struct serdes_config serdes1_cfg_tbl[] = {
+	/* SerDes 1 */
+	{1, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{2, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{3, {PCIE1, PCIE1, NONE, NONE} },
+	{4, {PCIE1, PCIE1, NONE, NONE} },
+	{5, {PCIE1, NONE, NONE, NONE} },
+	{6, {PCIE1, NONE, NONE, NONE} },
+	{}
+};
+
+int is_serdes_configured(enum srds_prtcl device)
+{
+	return (1 << device) & serdes1_prtcl_map;
+}
+
+void fsl_serdes_init(void)
+{
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+	u32 pordevsr = in_be32(&gur->pordevsr);
+	u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
+				MPC85xx_PORDEVSR_IO_SEL_SHIFT;
+	const struct serdes_config *ptr;
+	int lane;
+
+	debug("PORDEVSR[IO_SEL_SRDS] = %x\n", srds_cfg);
+
+	if (srds_cfg > ARRAY_SIZE(serdes1_cfg_tbl)) {
+		printf("Invalid PORDEVSR[IO_SEL_SRDS] = %d\n", srds_cfg);
+		return;
+	}
+
+	ptr = &serdes1_cfg_tbl[srds_cfg];
+	if (!ptr->protocol)
+		return;
+
+	for (lane = 0; lane < SRDS1_MAX_LANES; lane++) {
+		enum srds_prtcl lane_prtcl = ptr->lanes[lane];
+		serdes1_prtcl_map |= (1 << lane_prtcl);
+	}
+}
diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
index 5cd02ccde..cbb443fd2 100644
--- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c
+++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
@@ -245,6 +245,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 #ifdef CONFIG_SYS_FSL_ERRATUM_A006593
 	puts("Work-around for Erratum A006593 enabled\n");
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	puts("Work-around for Erratum A-005812 enabled\n");
+#endif
 	return 0;
 }
 
diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c
index 91ac4ee61..66bc6a2ea 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu.c
@@ -44,10 +44,10 @@ int checkcpu (void)
 	uint major, minor;
 	struct cpu_type *cpu;
 	char buf1[32], buf2[32];
-#if (defined(CONFIG_DDR_CLK_FREQ) || \
-	defined(CONFIG_FSL_CORENET)) && !defined(CONFIG_SYS_FSL_QORIQ_CHASSIS2)
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-#endif /* CONFIG_FSL_CORENET */
+#if defined(CONFIG_DDR_CLK_FREQ) || defined(CONFIG_FSL_CORENET)
+	ccsr_gur_t __iomem *gur =
+		(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
 
 	/*
 	 * Cornet platforms use ddr sync bit in RCW to indicate sync vs async
@@ -211,6 +211,21 @@ int checkcpu (void)
 
 	puts("L1:    D-cache 32 kB enabled\n       I-cache 32 kB enabled\n");
 
+#ifdef CONFIG_FSL_CORENET
+	/* Display the RCW, so that no one gets confused as to what RCW
+	 * we're actually using for this boot.
+	 */
+	puts("Reset Configuration Word (RCW):");
+	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+		u32 rcw = in_be32(&gur->rcwsr[i]);
+
+		if ((i % 4) == 0)
+			printf("\n       %08x:", i * 4);
+		printf(" %08x", rcw);
+	}
+	puts("\n");
+#endif
+
 	return 0;
 }
 
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c
index 25beda233..48b38263f 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c
@@ -399,6 +399,14 @@ int cpu_init_r(void)
 		sync();
 	}
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	/*
+	 * A-005812 workaround sets bit 32 of SPR 976 for SoCs running
+	 * in write shadow mode. Checking DCWS before setting SPR 976.
+	 */
+	if (mfspr(L1CSR2) & L1CSR2_DCWS)
+		mtspr(SPRN_HDBCR0, (mfspr(SPRN_HDBCR0) | 0x80000000));
+#endif
 
 #if defined(CONFIG_PPC_SPINTABLE_COMPATIBLE) && defined(CONFIG_MP)
 	spin = getenv("spin_table_compat");
@@ -532,8 +540,10 @@ skip_l2:
 
 	enable_cpc();
 
+#ifndef CONFIG_SYS_FSL_NO_SERDES
 	/* needs to be in ram since code uses global static vars */
 	fsl_serdes_init();
+#endif
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A005871
 	if (IS_SVR_REV(svr, 1, 0)) {
diff --git a/arch/powerpc/cpu/mpc85xx/ddr-gen1.c b/arch/powerpc/cpu/mpc85xx/ddr-gen1.c
index 8a86819fb..4dd8c0b5b 100644
--- a/arch/powerpc/cpu/mpc85xx/ddr-gen1.c
+++ b/arch/powerpc/cpu/mpc85xx/ddr-gen1.c
@@ -15,7 +15,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
diff --git a/arch/powerpc/cpu/mpc85xx/ddr-gen2.c b/arch/powerpc/cpu/mpc85xx/ddr-gen2.c
index a70586252..542bc84ac 100644
--- a/arch/powerpc/cpu/mpc85xx/ddr-gen2.c
+++ b/arch/powerpc/cpu/mpc85xx/ddr-gen2.c
@@ -16,7 +16,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
diff --git a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c
index c5b47200e..1be51d330 100644
--- a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c
+++ b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c
@@ -15,8 +15,18 @@
 #error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
 #endif
 
+
+/*
+ * regs has the to-be-set values for DDR controller registers
+ * ctrl_num is the DDR controller number
+ * step: 0 goes through the initialization in one pass
+ *       1 sets registers and returns before enabling controller
+ *       2 resumes from step 1 and continues to initialize
+ * Dividing the initialization to two steps to deassert DDR reset signal
+ * to comply with JEDEC specs for RDIMMs.
+ */
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i, bus_width;
 	volatile ccsr_ddr_t *ddr;
@@ -54,6 +64,9 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 		return;
 	}
 
+	if (step == 2)
+		goto step2;
+
 	if (regs->ddr_eor)
 		out_be32(&ddr->eor, regs->ddr_eor);
 #ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134
@@ -123,10 +136,17 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5);
 	out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
 	out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
+#ifndef CONFIG_SYS_FSL_DDR_EMU
+	/*
+	 * Skip these two registers if running on emulator
+	 * because emulator doesn't have skew between bytes.
+	 */
+
 	if (regs->ddr_wrlvl_cntl_2)
 		out_be32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2);
 	if (regs->ddr_wrlvl_cntl_3)
 		out_be32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3);
+#endif
 
 	out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr);
 	out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
@@ -150,6 +170,20 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	out_be32(&ddr->debug[21], 0x24000000);
 #endif /* CONFIG_SYS_FSL_ERRATUM_DDR_A003474 */
 
+	/*
+	 * For RDIMMs, JEDEC spec requires clocks to be stable before reset is
+	 * deasserted. Clocks start when any chip select is enabled and clock
+	 * control register is set. Because all DDR components are connected to
+	 * one reset signal, this needs to be done in two steps. Step 1 is to
+	 * get the clocks started. Step 2 resumes after reset signal is
+	 * deasserted.
+	 */
+	if (step == 1) {
+		udelay(200);
+		return;
+	}
+
+step2:
 	/* Set, but do not enable the memory */
 	temp_sdram_cfg = regs->ddr_sdram_cfg;
 	temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN);
diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c
index cfaa2edce..84bb8fab8 100644
--- a/arch/powerpc/cpu/mpc85xx/fdt.c
+++ b/arch/powerpc/cpu/mpc85xx/fdt.c
@@ -604,8 +604,12 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 
 	fdt_add_enet_stashing(blob);
 
+#ifndef CONFIG_FSL_TBCLK_EXTRA_DIV
+#define CONFIG_FSL_TBCLK_EXTRA_DIV 1
+#endif
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
-		"timebase-frequency", get_tbclk(), 1);
+		"timebase-frequency", get_tbclk() / CONFIG_FSL_TBCLK_EXTRA_DIV,
+		1);
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
 		"bus-frequency", bd->bi_busfreq, 1);
 	get_sys_info(&sysinfo);
diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.h b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.h
index 6de572d59..d515b234a 100644
--- a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.h
+++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.h
@@ -9,5 +9,4 @@
 
 int is_serdes_prtcl_valid(int serdes, u32 prtcl);
 int serdes_lane_enabled(int lane);
-enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane);
 #endif /* __FSL_CORENET2_SERDES_H */
diff --git a/arch/powerpc/cpu/mpc85xx/release.S b/arch/powerpc/cpu/mpc85xx/release.S
index 15bbbc15a..c15e83b52 100644
--- a/arch/powerpc/cpu/mpc85xx/release.S
+++ b/arch/powerpc/cpu/mpc85xx/release.S
@@ -226,6 +226,21 @@ __secondary_start_page:
 2:
 #endif
 
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	/*
+	 * A-005812 workaround sets bit 32 of SPR 976 for SoCs running in
+	 * write shadow mode. This code should run after other code setting
+	 * DCWS.
+	 */
+	mfspr	r3,L1CSR2
+	andis.	r3,r3,(L1CSR2_DCWS)@h
+	beq	1f
+	mfspr	r3, SPRN_HDBCR0
+	oris	r3, r3, 0x8000
+	mtspr	SPRN_HDBCR0, r3
+1:
+#endif
+
 #ifdef CONFIG_BACKSIDE_L2_CACHE
 	/* skip L2 setup on P2040/P2040E as they have no L2 */
 	mfspr	r3,SPRN_SVR
diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S
index cfc3a60d2..ad57a9cfa 100644
--- a/arch/powerpc/cpu/mpc85xx/start.S
+++ b/arch/powerpc/cpu/mpc85xx/start.S
@@ -33,7 +33,8 @@
 #define MINIMAL_SPL
 #endif
 
-#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SECURE_BOOT)
+#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && \
+	!defined(CONFIG_SECURE_BOOT) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define NOR_BOOT
 #endif
 
diff --git a/arch/powerpc/cpu/mpc85xx/t4240_ids.c b/arch/powerpc/cpu/mpc85xx/t4240_ids.c
index e173cb5f9..54c1cfd2c 100644
--- a/arch/powerpc/cpu/mpc85xx/t4240_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/t4240_ids.c
@@ -65,8 +65,8 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
 #endif
 
 struct srio_liodn_id_table srio_liodn_tbl[] = {
-	SET_SRIO_LIODN_1(1, 307),
-	SET_SRIO_LIODN_1(2, 387),
+	SET_SRIO_LIODN_BASE(1, 307),
+	SET_SRIO_LIODN_BASE(2, 387),
 };
 int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
 
@@ -159,10 +159,10 @@ int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
 #ifdef CONFIG_SYS_DPAA_RMAN
 struct liodn_id_table rman_liodn_tbl[] = {
 	/* Set RMan block 0-3 liodn offset */
-	SET_RMAN_LIODN(0, 678),
-	SET_RMAN_LIODN(1, 679),
-	SET_RMAN_LIODN(2, 680),
-	SET_RMAN_LIODN(3, 681),
+	SET_RMAN_LIODN(0, 6),
+	SET_RMAN_LIODN(1, 7),
+	SET_RMAN_LIODN(2, 8),
+	SET_RMAN_LIODN(3, 9),
 };
 int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl);
 #endif
diff --git a/arch/powerpc/cpu/mpc86xx/ddr-8641.c b/arch/powerpc/cpu/mpc86xx/ddr-8641.c
index 92ba26dc8..33a91f9f7 100644
--- a/arch/powerpc/cpu/mpc86xx/ddr-8641.c
+++ b/arch/powerpc/cpu/mpc86xx/ddr-8641.c
@@ -15,7 +15,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	volatile ccsr_ddr_t *ddr;
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index 7369582ef..c67be4ef2 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -79,6 +79,9 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(BSC9131, 9131, 1),
 	CPU_TYPE_ENTRY(BSC9132, 9132, 2),
 	CPU_TYPE_ENTRY(BSC9232, 9232, 2),
+	CPU_TYPE_ENTRY(C291, C291, 1),
+	CPU_TYPE_ENTRY(C292, C292, 1),
+	CPU_TYPE_ENTRY(C293, C293, 1),
 #elif defined(CONFIG_MPC86xx)
 	CPU_TYPE_ENTRY(8610, 8610, 1),
 	CPU_TYPE_ENTRY(8641, 8641, 2),
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c
index ff5812df5..242eb47ac 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c
@@ -364,7 +364,7 @@ static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
 
 	ddr->timing_cfg_3 = (0
 		| ((ext_pretoact & 0x1) << 28)
-		| ((ext_acttopre & 0x2) << 24)
+		| ((ext_acttopre & 0x3) << 24)
 		| ((ext_acttorw & 0x1) << 22)
 		| ((ext_refrec & 0x1F) << 16)
 		| ((ext_caslat & 0x3) << 12)
@@ -681,6 +681,7 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 	unsigned int odt_cfg = 0;	/* ODT configuration */
 	unsigned int num_pr;		/* Number of posted refreshes */
 	unsigned int slow = 0;		/* DDR will be run less than 1250 */
+	unsigned int x4_en = 0;		/* x4 DRAM enable */
 	unsigned int obc_cfg;		/* On-The-Fly Burst Chop Cfg */
 	unsigned int ap_en;		/* Address Parity Enable */
 	unsigned int d_init;		/* DRAM data initialization */
@@ -725,6 +726,8 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 		ap_en = 0;
 	}
 
+	x4_en = popts->x4_en ? 1 : 0;
+
 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/* Use the DDR controller to auto initialize memory. */
 	d_init = popts->ECC_init_using_memctl;
@@ -747,6 +750,7 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 		| ((odt_cfg & 0x3) << 21)
 		| ((num_pr & 0xf) << 12)
 		| ((slow & 1) << 11)
+		| (x4_en << 10)
 		| (qd_en << 9)
 		| (unq_mrs_en << 8)
 		| ((obc_cfg & 0x1) << 6)
@@ -1585,8 +1589,8 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts,
 				| ((ea & 0xFFF) << 0)	/* ending address MSB */
 				);
 		} else {
-			debug("FSLDDR: setting bnds to 0 for inactive CS\n");
-			ddr->cs[i].bnds = 0;
+			/* setting bnds to 0xffffffff for inactive CS */
+			ddr->cs[i].bnds = 0xffffffff;
 		}
 
 		debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds);
@@ -1638,5 +1642,10 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts,
 
 	set_ddr_sdram_rcw(ddr, popts, common_dimm);
 
+#ifdef CONFIG_SYS_FSL_DDR_EMU
+	/* disble DDR training for emulator */
+	ddr->debug[2] = 0x00000400;
+	ddr->debug[4] = 0xff800000;
+#endif
 	return check_fsl_memctl_config_regs(ddr);
 }
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h b/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h
index 4dd55fc4c..c173a5a74 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h
@@ -96,7 +96,7 @@ unsigned int check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr);
 
 /* processor specific function */
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-				   unsigned int ctrl_num);
+				   unsigned int ctrl_num, int step);
 
 /* board specific function */
 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c
index 3e7c269e4..b67158c0f 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c
@@ -129,6 +129,7 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd,
 		pdimm->ec_sdram_width = 0;
 	pdimm->data_width = pdimm->primary_sdram_width
 			  + pdimm->ec_sdram_width;
+	pdimm->device_width = 1 << ((spd->organization & 0x7) + 2);
 
 	/* These are the types defined by the JEDEC DDR3 SPD spec */
 	pdimm->mirrored_dimm = 0;
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c b/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c
index 1ed6c7715..260fce577 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c
@@ -205,6 +205,7 @@ static void fsl_ddr_dimm_parameters_edit(fsl_ddr_info_t *pinfo,
 		DIMM_PARM(primary_sdram_width),
 		DIMM_PARM(ec_sdram_width),
 		DIMM_PARM(registered_dimm),
+		DIMM_PARM(device_width),
 
 		DIMM_PARM(n_row_addr),
 		DIMM_PARM(n_col_addr),
@@ -263,6 +264,7 @@ static void print_dimm_parameters(const dimm_params_t *pdimm)
 		DIMM_PARM(primary_sdram_width),
 		DIMM_PARM(ec_sdram_width),
 		DIMM_PARM(registered_dimm),
+		DIMM_PARM(device_width),
 
 		DIMM_PARM(n_row_addr),
 		DIMM_PARM(n_col_addr),
@@ -443,6 +445,7 @@ static void fsl_ddr_options_edit(fsl_ddr_info_t *pinfo,
 		CTRL_OPTIONS(twoT_en),
 		CTRL_OPTIONS(threeT_en),
 		CTRL_OPTIONS(ap_en),
+		CTRL_OPTIONS(x4_en),
 		CTRL_OPTIONS(bstopre),
 		CTRL_OPTIONS(wrlvl_override),
 		CTRL_OPTIONS(wrlvl_sample),
@@ -687,6 +690,7 @@ static void print_memctl_options(const memctl_options_t *popts)
 		CTRL_OPTIONS(threeT_en),
 		CTRL_OPTIONS(registered_dimm_en),
 		CTRL_OPTIONS(ap_en),
+		CTRL_OPTIONS(x4_en),
 		CTRL_OPTIONS(bstopre),
 		CTRL_OPTIONS(wrlvl_override),
 		CTRL_OPTIONS(wrlvl_sample),
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/main.c b/arch/powerpc/cpu/mpc8xxx/ddr/main.c
index 7a8636de1..9f4f25343 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/main.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/main.c
@@ -25,10 +25,6 @@ void fsl_ddr_set_lawbar(
 		unsigned int ctrl_num);
 void fsl_ddr_set_intl3r(const unsigned int granule_size);
 
-/* processor specific function */
-extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-				   unsigned int ctrl_num);
-
 #if defined(SPD_EEPROM_ADDRESS) || \
     defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \
     defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4)
@@ -365,9 +361,11 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 {
 	unsigned int i, j;
 	unsigned long long total_mem = 0;
+	int assert_reset;
 
 	fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg;
 	common_timing_params_t *timing_params = pinfo->common_timing_params;
+	assert_reset = board_need_mem_reset();
 
 	/* data bus width capacity adjust shift amount */
 	unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS];
@@ -462,7 +460,20 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 					timing_params[i].all_DIMMs_registered,
 					&pinfo->memctl_opts[i],
 					pinfo->dimm_params[i], i);
+			/*
+			 * For RDIMMs, JEDEC spec requires clocks to be stable
+			 * before reset signal is deasserted. For the boards
+			 * using fixed parameters, this function should be
+			 * be called from board init file.
+			 */
+			if (timing_params[i].all_DIMMs_registered)
+				assert_reset = 1;
 		}
+		if (assert_reset) {
+			debug("Asserting mem reset\n");
+			board_assert_mem_reset();
+		}
+
 	case STEP_ASSIGN_ADDRESSES:
 		/* STEP 5:  Assign addresses to chip selects */
 		check_interleaving_options(pinfo);
@@ -504,7 +515,13 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 				fsl_ddr_cfg_regs_t *reg = &ddr_reg[i];
 				if (reg->cs[j].config & 0x80000000) {
 					unsigned int end;
-					end = reg->cs[j].bnds & 0xFFF;
+					/*
+					 * 0xfffffff is a special value we put
+					 * for unused bnds
+					 */
+					if (reg->cs[j].bnds == 0xffffffff)
+						continue;
+					end = reg->cs[j].bnds & 0xffff;
 					if (end > max_end) {
 						max_end = end;
 					}
@@ -531,6 +548,7 @@ phys_size_t fsl_ddr_sdram(void)
 	unsigned int law_memctl = LAW_TRGT_IF_DDR_1;
 	unsigned long long total_memory;
 	fsl_ddr_info_t info;
+	int deassert_reset;
 
 	/* Reset info structure. */
 	memset(&info, 0, sizeof(fsl_ddr_info_t));
@@ -559,7 +577,21 @@ phys_size_t fsl_ddr_sdram(void)
 		}
 	}
 
-	/* Program configuration registers. */
+	/*
+	 * Program configuration registers.
+	 * JEDEC specs requires clocks to be stable before deasserting reset
+	 * for RDIMMs. Clocks start after chip select is enabled and clock
+	 * control register is set. During step 1, all controllers have their
+	 * registers set but not enabled. Step 2 proceeds after deasserting
+	 * reset through board FPGA or GPIO.
+	 * For non-registered DIMMs, initialization can go through but it is
+	 * also OK to follow the same flow.
+	 */
+	deassert_reset = board_need_mem_reset();
+	for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+		if (info.common_timing_params[i].all_DIMMs_registered)
+			deassert_reset = 1;
+	}
 	for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
 		debug("Programming controller %u\n", i);
 		if (info.common_timing_params[i].ndimms_present == 0) {
@@ -567,8 +599,22 @@ phys_size_t fsl_ddr_sdram(void)
 					"skipping programming\n", i);
 			continue;
 		}
-
-		fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i);
+		/*
+		 * The following call with step = 1 returns before enabling
+		 * the controller. It has to finish with step = 2 later.
+		 */
+		fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i,
+					deassert_reset ? 1 : 0);
+	}
+	if (deassert_reset) {
+		/* Use board FPGA or GPIO to deassert reset signal */
+		debug("Deasserting mem reset\n");
+		board_deassert_mem_reset();
+		for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+			/* Call with step = 2 to continue initialization */
+			fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]),
+						i, 2);
+		}
 	}
 
 	/* program LAWs */
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/options.c b/arch/powerpc/cpu/mpc8xxx/ddr/options.c
index 26369e099..30cdca497 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/options.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/options.c
@@ -700,6 +700,8 @@ unsigned int populate_memctl_options(int all_DIMMs_registered,
 	}
 #endif
 
+	popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0;
+
 	/* Choose burst length. */
 #if defined(CONFIG_FSL_DDR3)
 #if defined(CONFIG_E500MC)
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index 7ed93acdc..ce1bf0554 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -303,6 +303,7 @@
 
 #elif defined(CONFIG_PPC_P2041) /* also supports P2040 */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -336,6 +337,7 @@
 
 #elif defined(CONFIG_PPC_P3041)
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -366,9 +368,11 @@
 #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000
 #define CONFIG_SYS_FSL_ERRATUM_SRIO_A004034
 #define CONFIG_SYS_FSL_ERRATUM_A004849
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_PPC_P4080) /* also supports P4040 */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			8
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	4
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -410,10 +414,12 @@
 #define CONFIG_SYS_FSL_ERRATUM_A004849
 #define CONFIG_SYS_FSL_ERRATUM_A004580
 #define CONFIG_SYS_P4080_ERRATUM_PCIE_A003
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_PPC_P5020) /* also supports P5010 */
 #define CONFIG_SYS_PPC64		/* 64-bit core */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -444,6 +450,7 @@
 #elif defined(CONFIG_PPC_P5040)
 #define CONFIG_SYS_PPC64
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	3
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -469,6 +476,7 @@
 #define CONFIG_SYS_FSL_ERRATUM_A004510
 #define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV	0x10
 #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_BSC9131)
 #define CONFIG_MAX_CPUS			1
@@ -492,6 +500,10 @@
 #define CONFIG_TSECV2
 #define CONFIG_SYS_FSL_SEC_COMPAT	4
 #define CONFIG_NUM_DDR_CONTROLLERS	2
+#define CONFIG_SYS_FSL_DSP_DDR_ADDR	0x40000000
+#define CONFIG_SYS_FSL_DSP_M2_RAM_ADDR	0xb0000000
+#define CONFIG_SYS_FSL_DSP_M3_RAM_ADDR	0xc0000000
+#define CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT	0xff600000
 #define CONFIG_SYS_FSL_IFC_BANK_COUNT	3
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_NAND_FSL_IFC
@@ -536,6 +548,7 @@
 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS	2
 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM	9
 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM	5
+#define CONFIG_SYS_FSL_SRIO_LIODN
 #define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
 #define CONFIG_SYS_FSL_ERRATUM_A004468
@@ -576,6 +589,7 @@
 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS	2
 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM	9
 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM	5
+#define CONFIG_SYS_FSL_SRIO_LIODN
 #else
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_CORES_PER_CLUSTER 2
@@ -612,6 +626,18 @@
 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 
+#elif defined(CONFIG_PPC_C29X)
+#define CONFIG_MAX_CPUS			1
+#define CONFIG_FSL_SDHC_V2_3
+#define CONFIG_SYS_FSL_NUM_LAWS		12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB	3
+#define CONFIG_TSECV2_1
+#define CONFIG_SYS_FSL_SEC_COMPAT	6
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_SYS_FSL_IFC_BANK_COUNT	8
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
+
 #else
 #error Processor type not defined for this platform
 #endif
diff --git a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h
index ffe4db8b8..bd312ad5c 100644
--- a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h
+++ b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h
@@ -26,6 +26,7 @@ typedef struct dimm_params_s {
 	unsigned int primary_sdram_width;
 	unsigned int ec_sdram_width;
 	unsigned int registered_dimm;
+	unsigned int device_width;	/* x4, x8, x16 components */
 
 	/* SDRAM device parameters */
 	unsigned int n_row_addr;
diff --git a/arch/powerpc/include/asm/fsl_ddr_sdram.h b/arch/powerpc/include/asm/fsl_ddr_sdram.h
index 640d3297d..f4eec82d5 100644
--- a/arch/powerpc/include/asm/fsl_ddr_sdram.h
+++ b/arch/powerpc/include/asm/fsl_ddr_sdram.h
@@ -277,6 +277,7 @@ typedef struct memctl_options_s {
 	unsigned int mirrored_dimm;
 	unsigned int quad_rank_present;
 	unsigned int ap_en;	/* address parity enable for RDIMM */
+	unsigned int x4_en;	/* enable x4 devices */
 
 	/* Global Timing Parameters */
 	unsigned int cas_latency_override;
@@ -330,9 +331,31 @@ extern phys_size_t fsl_ddr_sdram(void);
 extern phys_size_t fsl_ddr_sdram_size(void);
 extern int fsl_use_spd(void);
 extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-					unsigned int ctrl_num);
+					unsigned int ctrl_num, int step);
 u32 fsl_ddr_get_intl3r(void);
 
+static void __board_assert_mem_reset(void)
+{
+}
+
+static void __board_deassert_mem_reset(void)
+{
+}
+
+void board_assert_mem_reset(void)
+	__attribute__((weak, alias("__board_assert_mem_reset")));
+
+void board_deassert_mem_reset(void)
+	__attribute__((weak, alias("__board_deassert_mem_reset")));
+
+static int __board_need_mem_reset(void)
+{
+	return 0;
+}
+
+int board_need_mem_reset(void)
+	__attribute__((weak, alias("__board_need_mem_reset")));
+
 /*
  * The 85xx boards have a common prototype for fixed_sdram so put the
  * declaration here.
diff --git a/arch/powerpc/include/asm/fsl_law.h b/arch/powerpc/include/asm/fsl_law.h
index bea163676..37d3a2246 100644
--- a/arch/powerpc/include/asm/fsl_law.h
+++ b/arch/powerpc/include/asm/fsl_law.h
@@ -82,7 +82,7 @@ enum law_trgt_if {
 #ifndef CONFIG_MPC8641
 	LAW_TRGT_IF_PCIE_1 = 0x02,
 #endif
-#if defined(CONFIG_BSC9131)
+#if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 	LAW_TRGT_IF_OCN_DSP = 0x03,
 #else
 #if !defined(CONFIG_MPC8572) && !defined(CONFIG_P2020)
@@ -92,9 +92,14 @@ enum law_trgt_if {
 	LAW_TRGT_IF_LBC = 0x04,
 	LAW_TRGT_IF_CCSR = 0x08,
 	LAW_TRGT_IF_DSP_CCSR = 0x09,
+	LAW_TRGT_IF_PLATFORM_SRAM = 0x0a,
 	LAW_TRGT_IF_DDR_INTRLV = 0x0b,
 	LAW_TRGT_IF_RIO = 0x0c,
+#if defined(CONFIG_BSC9132)
+	LAW_TRGT_IF_CLASS_DSP = 0x0d,
+#else
 	LAW_TRGT_IF_RIO_2 = 0x0d,
+#endif
 	LAW_TRGT_IF_DPAA_SWP_SRAM = 0x0e,
 	LAW_TRGT_IF_DDR = 0x0f,
 	LAW_TRGT_IF_DDR_2 = 0x16,	/* 2nd controller */
diff --git a/arch/powerpc/include/asm/fsl_liodn.h b/arch/powerpc/include/asm/fsl_liodn.h
index 3f543d924..44bc88dce 100644
--- a/arch/powerpc/include/asm/fsl_liodn.h
+++ b/arch/powerpc/include/asm/fsl_liodn.h
@@ -29,6 +29,13 @@ struct srio_liodn_id_table {
 		+ CONFIG_SYS_MPC85xx_GUTS_OFFSET + CONFIG_SYS_CCSRBAR, \
 	}
 
+#define SET_SRIO_LIODN_BASE(port, id_a) \
+	{ .id = { id_a }, .num_ids = 1, .portid = port, \
+	  .reg_offset[0] = offsetof(struct ccsr_rio, liodn) \
+		+ (port - 1) * 0x200 \
+		+ CONFIG_SYS_FSL_SRIO_ADDR, \
+	}
+
 struct liodn_id_table {
 	const char * compat;
 	u32 id[2];
diff --git a/arch/powerpc/include/asm/fsl_pci.h b/arch/powerpc/include/asm/fsl_pci.h
index c740da37c..749411c10 100644
--- a/arch/powerpc/include/asm/fsl_pci.h
+++ b/arch/powerpc/include/asm/fsl_pci.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007,2009-2012 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -13,6 +13,34 @@
 
 #define PEX_IP_BLK_REV_2_2	0x02080202
 #define PEX_IP_BLK_REV_2_3	0x02080203
+#define PEX_IP_BLK_REV_3_0	0x02080300
+
+/* Freescale-specific PCI config registers */
+#define FSL_PCI_PBFR		0x44
+
+#ifdef CONFIG_SYS_FSL_PCI_VER_3_X
+/* Currently only the PCIe capability is used, so hardcode the offset.
+ * if more capabilities need to be justified, the capability link method
+ * should be applied here
+ */
+#define FSL_PCIE_CAP_ID		0x70
+#define PCI_DCR		0x78    /* PCIe Device Control Register */
+#define PCI_DSR		0x7a    /* PCIe Device Status Register */
+#define PCI_LSR		0x82    /* PCIe Link Status Register */
+#define PCI_LCR		0x80    /* PCIe Link Control Register */
+#else
+#define FSL_PCIE_CAP_ID		0x4c
+#define PCI_DCR		0x54    /* PCIe Device Control Register */
+#define PCI_DSR		0x56    /* PCIe Device Status Register */
+#define PCI_LSR		0x5e    /* PCIe Link Status Register */
+#define PCI_LCR		0x5c    /* PCIe Link Control Register */
+#endif
+
+#define FSL_PCIE_CFG_RDY	0x4b0
+#define FSL_PROG_IF_AGENT	0x1
+
+#define PCI_LTSSM	0x404   /* PCIe Link Training, Status State Machine */
+#define  PCI_LTSSM_L0	0x16    /* L0 state */
 
 int fsl_setup_hose(struct pci_controller *hose, unsigned long addr);
 int fsl_is_pci_agent(struct pci_controller *hose);
@@ -149,7 +177,10 @@ typedef struct ccsr_pci {
 	u32	perr_cap3;	/* 0xe34 - PCIE Error Capture Register 3 */
 	char	res23[200];
 	u32	pdb_stat;	/* 0xf00 - PCIE Debug Status */
-	char	res24[252];
+	char	res24[16];
+	u32	pex_csr0;	/* 0xf14 - PEX Control/Status register 0*/
+	u32	pex_csr1;	/* 0xf18 - PEX Control/Status register 1*/
+	char	res25[228];
 } ccsr_fsl_pci_t;
 #define PCIE_CONFIG_PC	0x00020000
 #define PCIE_CONFIG_OB_CK	0x00002000
diff --git a/arch/powerpc/include/asm/fsl_serdes.h b/arch/powerpc/include/asm/fsl_serdes.h
index 59189adb3..1106d2805 100644
--- a/arch/powerpc/include/asm/fsl_serdes.h
+++ b/arch/powerpc/include/asm/fsl_serdes.h
@@ -90,6 +90,7 @@ void fsl_serdes_init(void);
 #ifdef CONFIG_FSL_CORENET
 #ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2
 int serdes_get_first_lane(u32 sd, enum srds_prtcl device);
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane);
 #else
 int serdes_get_first_lane(enum srds_prtcl device);
 #endif
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 81b3322fe..2ed384e30 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -1544,6 +1544,18 @@ struct rio_pw {
 };
 #endif
 
+#ifdef CONFIG_SYS_FSL_SRIO_LIODN
+struct rio_liodn {
+	u32	plbr;
+	u8	res0[28];
+	u32	plaor;
+	u8	res1[12];
+	u32	pludr;
+	u32	plldr;
+	u8	res2[456];
+};
+#endif
+
 /* RapidIO Registers */
 struct ccsr_rio {
 	struct rio_arch	arch;
@@ -1566,6 +1578,10 @@ struct ccsr_rio {
 	u8	res7[100];
 	struct rio_pw	pw;
 #endif
+#ifdef CONFIG_SYS_FSL_SRIO_LIODN
+	u8	res5[8192];
+	struct rio_liodn liodn[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+#endif
 };
 #endif
 
@@ -2131,6 +2147,11 @@ typedef struct ccsr_gur {
 #ifdef CONFIG_MPC8536
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x3e000000
 #define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT	25
+#elif defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORPLLSR_DDR_RATIO	0x00003f00
+#define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT	(9 - ((gur->pordevsr2 \
+					& MPC85xx_PORDEVSR2_DDR_SPD_0) \
+					>> MPC85xx_PORDEVSR2_DDR_SPD_0_SHIFT))
 #else
 #if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x00003f00
@@ -2178,6 +2199,9 @@ typedef struct ccsr_gur {
 #elif defined(CONFIG_BSC9132)
 #define MPC85xx_PORDEVSR_IO_SEL		0x00FE0000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	17
+#elif defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORDEVSR_IO_SEL		0x00e00000
+#define MPC85xx_PORDEVSR_IO_SEL_SHIFT	21
 #else
 #define MPC85xx_PORDEVSR_IO_SEL		0x00780000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	19
@@ -2193,6 +2217,10 @@ typedef struct ccsr_gur {
 #define MPC85xx_PORDEVSR_RIO_DEV_ID	0x00000007
 	u32	pordbgmsr;	/* POR debug mode status */
 	u32	pordevsr2;	/* POR I/O device status 2 */
+#if defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORDEVSR2_DDR_SPD_0	0x00000008
+#define MPC85xx_PORDEVSR2_DDR_SPD_0_SHIFT	3
+#endif
 /* The 8544 RM says this is bit 26, but it's really bit 24 */
 #define MPC85xx_PORDEVSR2_SEC_CFG	0x00000080
 	u8	res1[8];
@@ -2339,6 +2367,11 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR0_SIM_SEL_MASK	0x0003b000
 #define MPC85xx_PMUXCR0_SIM_SEL		0x00014000
 #endif
+#if defined(CONFIG_PPC_C29X)
+#define MPC85xx_PMUXCR_SPI_MASK			0x00000300
+#define MPC85xx_PMUXCR_SPI			0x00000000
+#define MPC85xx_PMUXCR_SPI_GPIO			0x00000100
+#endif
 	u32	pmuxcr2;	/* Alt. function signal multiplex control 2 */
 #if defined(CONFIG_P1010) || defined(CONFIG_P1014)
 #define MPC85xx_PMUXCR2_UART_GPIO		0x40000000
@@ -2526,7 +2559,9 @@ typedef struct serdes_corenet {
 #define SRDS_RSTCTL_RSTDONE	0x40000000
 #define SRDS_RSTCTL_RSTERR	0x20000000
 #define SRDS_RSTCTL_SWRST	0x10000000
-#define SRDS_RSTCTL_SDPD	0x00000020
+#define SRDS_RSTCTL_SDEN	0x00000020
+#define SRDS_RSTCTL_SDRST_B	0x00000040
+#define SRDS_RSTCTL_PLLRST_B	0x00000080
 		u32	pllcr0; /* PLL Control Register 0 */
 #define SRDS_PLLCR0_POFF		0x80000000
 #define SRDS_PLLCR0_RFCK_SEL_MASK	0x70000000
@@ -3008,12 +3043,18 @@ struct ccsr_pman {
 #define CONFIG_SYS_MPC85xx_USB2_OFFSET		0x23000
 #ifdef CONFIG_TSECV2
 #define CONFIG_SYS_TSEC1_OFFSET			0xB0000
+#elif defined(CONFIG_TSECV2_1)
+#define CONFIG_SYS_TSEC1_OFFSET			0x10000
 #else
 #define CONFIG_SYS_TSEC1_OFFSET			0x24000
 #endif
 #define CONFIG_SYS_MDIO1_OFFSET			0x24000
 #define CONFIG_SYS_MPC85xx_ESDHC_OFFSET		0x2e000
+#if defined(CONFIG_PPC_C29X)
+#define CONFIG_SYS_FSL_SEC_OFFSET		0x80000
+#else
 #define CONFIG_SYS_FSL_SEC_OFFSET		0x30000
+#endif
 #define CONFIG_SYS_MPC85xx_SERDES2_OFFSET	0xE3100
 #define CONFIG_SYS_MPC85xx_SERDES1_OFFSET	0xE3000
 #define CONFIG_SYS_SNVS_OFFSET			0xE6000
@@ -3031,6 +3072,12 @@ struct ccsr_pman {
 #define CONFIG_SYS_MPC85xx_GUTS_OFFSET		0xE0000
 #define CONFIG_SYS_FSL_SRIO_OFFSET		0xC0000
 
+#if defined(CONFIG_BSC9132)
+#define CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET	0x10000
+#define CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR \
+	(CONFIG_SYS_FSL_DSP_CCSRBAR + CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET)
+#endif
+
 #define CONFIG_SYS_FSL_CPC_ADDR	\
 	(CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_CPC_OFFSET)
 #define CONFIG_SYS_FSL_QMAN_ADDR \
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 56b22d840..64a6f9c54 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1119,6 +1119,9 @@
 #define SVR_T4240	0x824000
 #define SVR_T4120	0x824001
 #define SVR_T4160	0x824100
+#define SVR_C291	0x850000
+#define SVR_C292	0x850020
+#define SVR_C293	0x850030
 #define SVR_B4860	0X868000
 #define SVR_G4860	0x868001
 #define SVR_G4060	0x868003