Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

1 files changed, 7 insertions, 10 deletions

diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index cc2bf979607..66338e7ebfb 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -77,12 +77,12 @@ static struct at91_cf_data __initdata dk_cf_data = {
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata dk_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata dk_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 #endif
 
@@ -177,9 +177,6 @@ static struct gpio_led dk_leds[] = {
 
 static void __init dk_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -208,7 +205,7 @@ static void __init dk_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(0, &dk_mmc_data);
+	at91_add_device_mci(0, &dk_mci0_data);
 #endif
 	/* NAND */
 	at91_add_device_nand(&dk_nand_data);