Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

1 files changed, 27 insertions, 10 deletions

diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 5d96cb85175..abe9fed7a3e 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -69,12 +69,12 @@ static struct at91_udc_data __initdata kb9202_udc_data = {
 	.pullup_pin	= AT91_PIN_PB22,
 };
 
-static struct at91_mmc_data __initdata kb9202_mmc_data = {
-	.det_pin	= AT91_PIN_PB2,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata kb9202_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB2,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -96,11 +96,26 @@ static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.num_parts	= ARRAY_SIZE(kb9202_nand_partition),
 };
 
+/*
+ * LEDs
+ */
+static struct gpio_led kb9202_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PC19,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* D2 */
+		.name			= "led2",
+		.gpio			= AT91_PIN_PC18,
+		.active_low		= 1,
+		.default_trigger	= "timer",
+	}
+};
+
 static void __init kb9202_board_init(void)
 {
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -121,13 +136,15 @@ static void __init kb9202_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&kb9202_udc_data);
 	/* MMC */
-	at91_add_device_mmc(0, &kb9202_mmc_data);
+	at91_add_device_mci(0, &kb9202_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* SPI */
 	at91_add_device_spi(NULL, 0);
 	/* NAND */
 	at91_add_device_nand(&kb9202_nand_data);
+	/* LEDs */
+	at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
 }
 
 MACHINE_START(KB9200, "KB920x")