From 4d0df9c1e94f32a9695be352fead3167fb5135c7 Mon Sep 17 00:00:00 2001 From: Andrii Tseglytskyi Date: Mon, 20 May 2013 22:42:08 +0000 Subject: OMAP3+: introduce generic ABB support Adaptive Body Biasing (ABB) modulates transistor bias voltages dynamically in order to optimize switching speed versus leakage. Adaptive Body-Bias ldos are present for some voltage domains starting with OMAP3630. There are three modes of operation: * Bypass - the default, it just follows the vdd voltage * Foward Body-Bias - applies voltage bias to increase transistor performance at the cost of power. Used to operate safely at high OPPs. * Reverse Body-Bias - applies voltage bias to decrease leakage and save power. Used to save power at lower OPPs. Signed-off-by: Andrii Tseglytskyi Acked-by: Nishanth Menon --- arch/arm/include/asm/omap_common.h | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index ee7b188d3..f8f3719bd 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -242,6 +242,8 @@ struct prcm_regs { u32 cm_l3init_fsusb_clkctrl; u32 cm_l3init_ocp2scp1_clkctrl; + u32 prm_irqstatus_mpu_2; + /* cm2.l4per */ u32 cm_l4per_clkstctrl; u32 cm_l4per_dynamicdep; @@ -328,6 +330,8 @@ struct prcm_regs { u32 prm_sldo_mpu_ctrl; u32 prm_sldo_mm_setup; u32 prm_sldo_mm_ctrl; + u32 prm_abbldo_mpu_setup; + u32 prm_abbldo_mpu_ctrl; u32 cm_div_m4_dpll_core; u32 cm_div_m5_dpll_core; @@ -350,6 +354,7 @@ struct prcm_regs { struct omap_sys_ctrl_regs { u32 control_status; + u32 control_std_fuse_opp_vdd_mpu_2; u32 control_core_mmr_lock1; u32 control_core_mmr_lock2; u32 control_core_mmr_lock3; @@ -419,6 +424,7 @@ struct omap_sys_ctrl_regs { u32 control_port_emif2_sdram_config; u32 control_emif1_sdram_config_ext; u32 control_emif2_sdram_config_ext; + u32 control_wkup_ldovbb_mpu_voltage_ctrl; u32 control_smart1nopmio_padconf_0; u32 control_smart1nopmio_padconf_1; u32 control_padconf_mode; @@ -545,6 +551,9 @@ void enable_non_essential_clocks(void); void scale_vcores(struct vcores_data const *); u32 get_offset_code(u32 volt_offset, struct pmic_data *pmic); void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic); +void abb_setup(u32 fuse, u32 ldovbb, u32 setup, u32 control, + u32 txdone, u32 txdone_mask, u32 opp); +s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb); /* Max value for DPLL multiplier M */ #define OMAP_DPLL_MAX_N 127 @@ -555,6 +564,19 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic); #define OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL 2 #define OMAP_INIT_CONTEXT_UBOOT_AFTER_CH 3 +/* ABB */ +#define OMAP_ABB_NOMINAL_OPP 0 +#define OMAP_ABB_FAST_OPP 1 +#define OMAP_ABB_SLOW_OPP 3 +#define OMAP_ABB_CONTROL_FAST_OPP_SEL_MASK (0x1 << 0) +#define OMAP_ABB_CONTROL_SLOW_OPP_SEL_MASK (0x1 << 1) +#define OMAP_ABB_CONTROL_OPP_CHANGE_MASK (0x1 << 2) +#define OMAP_ABB_CONTROL_SR2_IN_TRANSITION_MASK (0x1 << 6) +#define OMAP_ABB_SETUP_SR2EN_MASK (0x1 << 0) +#define OMAP_ABB_SETUP_ACTIVE_FBB_SEL_MASK (0x1 << 2) +#define OMAP_ABB_SETUP_ACTIVE_RBB_SEL_MASK (0x1 << 1) +#define OMAP_ABB_SETUP_SR2_WTCNT_VALUE_MASK (0xff << 8) + static inline u32 omap_revision(void) { extern u32 *const omap_si_rev; -- cgit v1.2.3-70-g09d2 From 9239f5b62550e9f1438c784cb8d1e578dc3852a8 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 30 May 2013 02:54:30 +0000 Subject: ARM: OMAP4+: Cleanup header files After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap4/prcm-regs.c | 3 +++ arch/arm/cpu/armv7/omap5/prcm-regs.c | 2 ++ arch/arm/include/asm/arch-omap4/clocks.h | 28 ---------------------------- arch/arm/include/asm/arch-omap4/cpu.h | 12 ------------ arch/arm/include/asm/arch-omap4/omap.h | 14 -------------- arch/arm/include/asm/arch-omap5/clocks.h | 22 ---------------------- arch/arm/include/asm/arch-omap5/cpu.h | 12 ------------ arch/arm/include/asm/arch-omap5/omap.h | 31 +------------------------------ arch/arm/include/asm/omap_common.h | 4 +--- board/ti/omap5_uevm/evm.c | 12 ++++++++---- board/ti/panda/panda.c | 20 ++++++++++++-------- board/ti/sdp4430/sdp.c | 16 ++++++++++------ drivers/usb/musb/omap3.c | 4 +++- 13 files changed, 40 insertions(+), 140 deletions(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap4/prcm-regs.c b/arch/arm/cpu/armv7/omap4/prcm-regs.c index 7225a301b..7e71ca0a2 100644 --- a/arch/arm/cpu/armv7/omap4/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap4/prcm-regs.c @@ -301,6 +301,8 @@ struct omap_sys_ctrl_regs const omap4_ctrl = { .control_ldosram_iva_voltage_ctrl = 0x4A002320, .control_ldosram_mpu_voltage_ctrl = 0x4A002324, .control_ldosram_core_voltage_ctrl = 0x4A002328, + .control_usbotghs_ctrl = 0x4A00233C, + .control_padconf_core_base = 0x4A100000, .control_pbiaslite = 0x4A100600, .control_lpddr2io1_0 = 0x4A100638, .control_lpddr2io1_1 = 0x4A10063C, @@ -312,4 +314,5 @@ struct omap_sys_ctrl_regs const omap4_ctrl = { .control_lpddr2io2_3 = 0x4A100654, .control_efuse_1 = 0x4A100700, .control_efuse_2 = 0x4A100704, + .control_padconf_wkup_base = 0x4A31E000, }; diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index 501073902..f3b315516 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -313,6 +313,7 @@ struct prcm_regs const omap5_es1_prcm = { struct omap_sys_ctrl_regs const omap5_ctrl = { .control_status = 0x4A002134, .control_std_fuse_opp_vdd_mpu_2 = 0x4A0021B4, + .control_padconf_core_base = 0x4A002800, .control_paconf_global = 0x4A002DA0, .control_paconf_mode = 0x4A002DA4, .control_smart1io_padconf_0 = 0x4A002DA8, @@ -361,6 +362,7 @@ struct omap_sys_ctrl_regs const omap5_ctrl = { .control_emif1_sdram_config_ext = 0x4AE0C144, .control_emif2_sdram_config_ext = 0x4AE0C148, .control_wkup_ldovbb_mpu_voltage_ctrl = 0x4AE0C318, + .control_padconf_wkup_base = 0x4AE0C800, .control_smart1nopmio_padconf_0 = 0x4AE0CDA0, .control_smart1nopmio_padconf_1 = 0x4AE0CDA4, .control_padconf_mode = 0x4AE0CDA8, diff --git a/arch/arm/include/asm/arch-omap4/clocks.h b/arch/arm/include/asm/arch-omap4/clocks.h index ed7a1c8be..f544edfbd 100644 --- a/arch/arm/include/asm/arch-omap4/clocks.h +++ b/arch/arm/include/asm/arch-omap4/clocks.h @@ -34,25 +34,6 @@ */ #define LDELAY 1000000 -#define CM_CLKMODE_DPLL_CORE 0x4A004120 -#define CM_CLKMODE_DPLL_PER 0x4A008140 -#define CM_CLKMODE_DPLL_MPU 0x4A004160 -#define CM_CLKSEL_CORE 0x4A004100 - -/* DPLL register offsets */ -#define CM_CLKMODE_DPLL 0 -#define CM_IDLEST_DPLL 0x4 -#define CM_AUTOIDLE_DPLL 0x8 -#define CM_CLKSEL_DPLL 0xC -#define CM_DIV_M2_DPLL 0x10 -#define CM_DIV_M3_DPLL 0x14 -#define CM_DIV_M4_DPLL 0x18 -#define CM_DIV_M5_DPLL 0x1C -#define CM_DIV_M6_DPLL 0x20 -#define CM_DIV_M7_DPLL 0x24 - -#define DPLL_CLKOUT_DIV_MASK 0x1F /* post-divider mask */ - /* CM_DLL_CTRL */ #define CM_DLL_CTRL_OVERRIDE_SHIFT 0 #define CM_DLL_CTRL_OVERRIDE_MASK (1 << 0) @@ -94,8 +75,6 @@ #define CM_CLKSEL_DCC_EN_SHIFT 22 #define CM_CLKSEL_DCC_EN_MASK (1 << 22) -#define OMAP4_DPLL_MAX_N 127 - /* CM_SYS_CLKSEL */ #define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 @@ -181,9 +160,7 @@ #define MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_MASK (1 << 25) /* Clock frequencies */ -#define OMAP_SYS_CLK_FREQ_38_4_MHZ 38400000 #define OMAP_SYS_CLK_IND_38_4_MHZ 6 -#define OMAP_32K_CLK_FREQ 32768 /* PRM_VC_VAL_BYPASS */ #define PRM_VC_I2C_CHANNEL_FREQ_KHZ 400 @@ -234,11 +211,6 @@ #define ALTCLKSRC_MODE_ACTIVE 1 -/* Defines for DPLL setup */ -#define DPLL_LOCKED_FREQ_TOLERANCE_0 0 -#define DPLL_LOCKED_FREQ_TOLERANCE_500_KHZ 500 -#define DPLL_LOCKED_FREQ_TOLERANCE_1_MHZ 1000 - #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 diff --git a/arch/arm/include/asm/arch-omap4/cpu.h b/arch/arm/include/asm/arch-omap4/cpu.h index 3a0bfbf0c..311c6ff52 100644 --- a/arch/arm/include/asm/arch-omap4/cpu.h +++ b/arch/arm/include/asm/arch-omap4/cpu.h @@ -115,18 +115,6 @@ struct watchdog { #define WD_UNLOCK1 0xAAAA #define WD_UNLOCK2 0x5555 -#define SYSCLKDIV_1 (0x1 << 6) -#define SYSCLKDIV_2 (0x1 << 7) - -#define CLKSEL_GPT1 (0x1 << 0) - -#define EN_GPT1 (0x1 << 0) -#define EN_32KSYNC (0x1 << 2) - -#define ST_WDT2 (0x1 << 5) - -#define RESETDONE (0x1 << 0) - #define TCLR_ST (0x1 << 0) #define TCLR_AR (0x1 << 1) #define TCLR_PRE (0x1 << 5) diff --git a/arch/arm/include/asm/arch-omap4/omap.h b/arch/arm/include/asm/arch-omap4/omap.h index 55a07605b..66afd9249 100644 --- a/arch/arm/include/asm/arch-omap4/omap.h +++ b/arch/arm/include/asm/arch-omap4/omap.h @@ -47,14 +47,6 @@ #define DRAM_ADDR_SPACE_START OMAP44XX_DRAM_ADDR_SPACE_START #define DRAM_ADDR_SPACE_END OMAP44XX_DRAM_ADDR_SPACE_END -/* CONTROL */ -#define CTRL_BASE (OMAP44XX_L4_CORE_BASE + 0x2000) -#define CONTROL_PADCONF_CORE (OMAP44XX_L4_CORE_BASE + 0x100000) -#define CONTROL_PADCONF_WKUP (OMAP44XX_L4_CORE_BASE + 0x31E000) - -/* LPDDR2 IO regs */ -#define LPDDR2_IO_REGS_BASE 0x4A100638 - /* CONTROL_ID_CODE */ #define CONTROL_ID_CODE 0x4A002204 @@ -79,15 +71,9 @@ /* Watchdog Timer2 - MPU watchdog */ #define WDT2_BASE (OMAP44XX_L4_WKUP_BASE + 0x14000) -/* 32KTIMER */ -#define SYNC_32KTIMER_BASE (OMAP44XX_L4_WKUP_BASE + 0x4000) - /* GPMC */ #define OMAP44XX_GPMC_BASE 0x50000000 -/* SYSTEM CONTROL MODULE */ -#define SYSCTRL_GENERAL_CORE_BASE 0x4A002000 - /* * Hardware Register Details */ diff --git a/arch/arm/include/asm/arch-omap5/clocks.h b/arch/arm/include/asm/arch-omap5/clocks.h index 68afa7669..6673a025f 100644 --- a/arch/arm/include/asm/arch-omap5/clocks.h +++ b/arch/arm/include/asm/arch-omap5/clocks.h @@ -35,19 +35,6 @@ */ #define LDELAY 1000000 -#define CM_CLKMODE_DPLL_CORE (OMAP54XX_L4_CORE_BASE + 0x4120) -#define CM_CLKMODE_DPLL_PER (OMAP54XX_L4_CORE_BASE + 0x8140) -#define CM_CLKMODE_DPLL_MPU (OMAP54XX_L4_CORE_BASE + 0x4160) -#define CM_CLKSEL_CORE (OMAP54XX_L4_CORE_BASE + 0x4100) - -/* DPLL register offsets */ -#define CM_CLKMODE_DPLL 0 -#define CM_IDLEST_DPLL 0x4 -#define CM_AUTOIDLE_DPLL 0x8 -#define CM_CLKSEL_DPLL 0xC - -#define DPLL_CLKOUT_DIV_MASK 0x1F /* post-divider mask */ - /* CM_DLL_CTRL */ #define CM_DLL_CTRL_OVERRIDE_SHIFT 0 #define CM_DLL_CTRL_OVERRIDE_MASK (1 << 0) @@ -93,8 +80,6 @@ #define CM_CLKSEL_DCC_EN_SHIFT 22 #define CM_CLKSEL_DCC_EN_MASK (1 << 22) -#define OMAP4_DPLL_MAX_N 127 - /* CM_SYS_CLKSEL */ #define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 @@ -195,9 +180,7 @@ #define RSTTIME1_MASK (0x3ff << 0) /* Clock frequencies */ -#define OMAP_SYS_CLK_FREQ_38_4_MHZ 38400000 #define OMAP_SYS_CLK_IND_38_4_MHZ 6 -#define OMAP_32K_CLK_FREQ 32768 /* PRM_VC_VAL_BYPASS */ #define PRM_VC_I2C_CHANNEL_FREQ_KHZ 400 @@ -247,11 +230,6 @@ #define TPS62361_BASE_VOLT_MV 500 #define TPS62361_VSEL0_GPIO 7 -/* Defines for DPLL setup */ -#define DPLL_LOCKED_FREQ_TOLERANCE_0 0 -#define DPLL_LOCKED_FREQ_TOLERANCE_500_KHZ 500 -#define DPLL_LOCKED_FREQ_TOLERANCE_1_MHZ 1000 - #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 diff --git a/arch/arm/include/asm/arch-omap5/cpu.h b/arch/arm/include/asm/arch-omap5/cpu.h index 044ab5581..4753f4624 100644 --- a/arch/arm/include/asm/arch-omap5/cpu.h +++ b/arch/arm/include/asm/arch-omap5/cpu.h @@ -119,18 +119,6 @@ struct watchdog { #define WD_UNLOCK1 0xAAAA #define WD_UNLOCK2 0x5555 -#define SYSCLKDIV_1 (0x1 << 6) -#define SYSCLKDIV_2 (0x1 << 7) - -#define CLKSEL_GPT1 (0x1 << 0) - -#define EN_GPT1 (0x1 << 0) -#define EN_32KSYNC (0x1 << 2) - -#define ST_WDT2 (0x1 << 5) - -#define RESETDONE (0x1 << 0) - #define TCLR_ST (0x1 << 0) #define TCLR_AR (0x1 << 1) #define TCLR_PRE (0x1 << 5) diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h index 1c1a64bd2..4fcd99f99 100644 --- a/arch/arm/include/asm/arch-omap5/omap.h +++ b/arch/arm/include/asm/arch-omap5/omap.h @@ -44,16 +44,8 @@ #define DRAM_ADDR_SPACE_START OMAP54XX_DRAM_ADDR_SPACE_START #define DRAM_ADDR_SPACE_END OMAP54XX_DRAM_ADDR_SPACE_END -/* CONTROL */ -#define CTRL_BASE (OMAP54XX_L4_CORE_BASE + 0x2000) -#define CONTROL_PADCONF_CORE (CTRL_BASE + 0x0800) -#define CONTROL_PADCONF_WKUP (OMAP54XX_L4_WKUP_BASE + 0xc800) - -/* LPDDR2 IO regs. To be verified */ -#define LPDDR2_IO_REGS_BASE 0x4A100638 - /* CONTROL_ID_CODE */ -#define CONTROL_ID_CODE (CTRL_BASE + 0x204) +#define CONTROL_ID_CODE 0x4A002204 /* To be verified */ #define OMAP5430_CONTROL_ID_CODE_ES1_0 0x0B94202F @@ -62,11 +54,6 @@ #define OMAP5432_CONTROL_ID_CODE_ES2_0 0x1B99802F #define DRA752_CONTROL_ID_CODE_ES1_0 0x0B99002F -/* STD_FUSE_PROD_ID_1 */ -#define STD_FUSE_PROD_ID_1 (CTRL_BASE + 0x218) -#define PROD_ID_1_SILICON_TYPE_SHIFT 16 -#define PROD_ID_1_SILICON_TYPE_MASK (3 << 16) - /* UART */ #define UART1_BASE (OMAP54XX_L4_PER_BASE + 0x6a000) #define UART2_BASE (OMAP54XX_L4_PER_BASE + 0x6c000) @@ -80,15 +67,9 @@ /* Watchdog Timer2 - MPU watchdog */ #define WDT2_BASE (OMAP54XX_L4_WKUP_BASE + 0x14000) -/* 32KTIMER */ -#define SYNC_32KTIMER_BASE (OMAP54XX_L4_WKUP_BASE + 0x4000) - /* GPMC */ #define OMAP54XX_GPMC_BASE 0x50000000 -/* SYSTEM CONTROL MODULE */ -#define SYSCTRL_GENERAL_CORE_BASE 0x4A002000 - /* * Hardware Register Details */ @@ -191,16 +172,6 @@ struct s32ktimer { /* base address for indirect vectors (internal boot mode) */ #define SRAM_ROM_VECT_BASE 0x4031F000 -/* Silicon revisions */ -#define OMAP4430_SILICON_ID_INVALID 0xFFFFFFFF -#define OMAP4430_ES1_0 0x44300100 -#define OMAP4430_ES2_0 0x44300200 -#define OMAP4430_ES2_1 0x44300210 -#define OMAP4430_ES2_2 0x44300220 -#define OMAP4430_ES2_3 0x44300230 -#define OMAP4460_ES1_0 0x44600100 -#define OMAP4460_ES1_1 0x44600110 - /* CONTROL_SRCOMP_XXX_SIDE */ #define OVERRIDE_XS_SHIFT 30 #define OVERRIDE_XS_MASK (1 << 30) diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index f8f3719bd..712d78b0a 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -367,6 +367,7 @@ struct omap_sys_ctrl_regs { u32 control_ldosram_iva_voltage_ctrl; u32 control_ldosram_mpu_voltage_ctrl; u32 control_ldosram_core_voltage_ctrl; + u32 control_usbotghs_ctrl; u32 control_padconf_core_base; u32 control_paconf_global; u32 control_paconf_mode; @@ -555,9 +556,6 @@ void abb_setup(u32 fuse, u32 ldovbb, u32 setup, u32 control, u32 txdone, u32 txdone_mask, u32 opp); s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb); -/* Max value for DPLL multiplier M */ -#define OMAP_DPLL_MAX_N 127 - /* HW Init Context */ #define OMAP_INIT_CONTEXT_SPL 0 #define OMAP_INIT_CONTEXT_UBOOT_FROM_NOR 1 diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c index 46db1bfe6..90046e896 100644 --- a/board/ti/omap5_uevm/evm.c +++ b/board/ti/omap5_uevm/evm.c @@ -71,22 +71,26 @@ int misc_init_r(void) void set_muxconf_regs_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_essential, sizeof(core_padconf_array_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_essential, sizeof(wkup_padconf_array_essential) / sizeof(struct pad_conf_entry)); } void set_muxconf_regs_non_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_non_essential, sizeof(core_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_non_essential, sizeof(wkup_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); } diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index 2bbe392d8..4335259e5 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -139,16 +139,18 @@ int misc_init_r(void) void set_muxconf_regs_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_essential, sizeof(core_padconf_array_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_essential, sizeof(wkup_padconf_array_essential) / sizeof(struct pad_conf_entry)); if (omap_revision() >= OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_WKUP, + do_set_mux((*ctrl)->control_padconf_wkup_base, wkup_padconf_array_essential_4460, sizeof(wkup_padconf_array_essential_4460) / sizeof(struct pad_conf_entry)); @@ -156,27 +158,29 @@ void set_muxconf_regs_essential(void) void set_muxconf_regs_non_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_non_essential, sizeof(core_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); if (omap_revision() < OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_CORE, + do_set_mux((*ctrl)->control_padconf_core_base, core_padconf_array_non_essential_4430, sizeof(core_padconf_array_non_essential_4430) / sizeof(struct pad_conf_entry)); else - do_set_mux(CONTROL_PADCONF_CORE, + do_set_mux((*ctrl)->control_padconf_core_base, core_padconf_array_non_essential_4460, sizeof(core_padconf_array_non_essential_4460) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_non_essential, sizeof(wkup_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); if (omap_revision() < OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_WKUP, + do_set_mux((*ctrl)->control_padconf_wkup_base, wkup_padconf_array_non_essential_4430, sizeof(wkup_padconf_array_non_essential_4430) / sizeof(struct pad_conf_entry)); diff --git a/board/ti/sdp4430/sdp.c b/board/ti/sdp4430/sdp.c index 4c1a4f7e7..5dd1ba3cb 100644 --- a/board/ti/sdp4430/sdp.c +++ b/board/ti/sdp4430/sdp.c @@ -72,16 +72,18 @@ int misc_init_r(void) void set_muxconf_regs_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_essential, sizeof(core_padconf_array_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_essential, sizeof(wkup_padconf_array_essential) / sizeof(struct pad_conf_entry)); if (omap_revision() >= OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_WKUP, + do_set_mux((*ctrl)->control_padconf_wkup_base, wkup_padconf_array_essential_4460, sizeof(wkup_padconf_array_essential_4460) / sizeof(struct pad_conf_entry)); @@ -89,16 +91,18 @@ void set_muxconf_regs_essential(void) void set_muxconf_regs_non_essential(void) { - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_core_base, + core_padconf_array_non_essential, sizeof(core_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + do_set_mux((*ctrl)->control_padconf_wkup_base, + wkup_padconf_array_non_essential, sizeof(wkup_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); if (omap_revision() < OMAP4460_ES1_0) { - do_set_mux(CONTROL_PADCONF_WKUP, + do_set_mux((*ctrl)->control_padconf_wkup_base, wkup_padconf_array_non_essential_4430, sizeof(wkup_padconf_array_non_essential_4430) / sizeof(struct pad_conf_entry)); diff --git a/drivers/usb/musb/omap3.c b/drivers/usb/musb/omap3.c index c7876ed09..a395ebcc6 100644 --- a/drivers/usb/musb/omap3.c +++ b/drivers/usb/musb/omap3.c @@ -30,6 +30,7 @@ * MA 02111-1307 USA */ +#include #include #include #include "omap3.h" @@ -135,7 +136,8 @@ int musb_platform_init(void) #endif #ifdef CONFIG_OMAP4430 - u32 *usbotghs_control = (u32 *)(CTRL_BASE + 0x33C); + u32 *usbotghs_control = + (u32 *)((*ctrl)->control_usbotghs_ctrl); *usbotghs_control = 0x15; #endif platform_needs_initialization = 0; -- cgit v1.2.3-70-g09d2 From 4ca94d81869f8c9ba3e72eac3a99d3eef29df991 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 30 May 2013 02:54:33 +0000 Subject: ARM: OMAP4+: pmic: Make generic bus init and write functions Voltage scaling can be done in two ways: -> Using SR I2C -> Using GP I2C In order to support both, have a function pointer in pmic_data so that we can call as per our requirement. Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 6 ++---- arch/arm/cpu/armv7/omap-common/vc.c | 14 +++++++++++++- arch/arm/cpu/armv7/omap4/hw_data.c | 11 ++++++++++- arch/arm/cpu/armv7/omap5/hw_data.c | 3 +++ arch/arm/include/asm/arch-omap4/sys_proto.h | 2 +- arch/arm/include/asm/arch-omap5/sys_proto.h | 2 +- arch/arm/include/asm/omap_common.h | 3 +++ 7 files changed, 33 insertions(+), 8 deletions(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 403b672f7..6c8e0632c 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -487,6 +487,7 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) u32 offset = volt_mv; int ret = 0; + pmic->pmic_bus_init(); /* See if we can first get the GPIO if needed */ if (pmic->gpio_en) ret = gpio_request(pmic->gpio, "PMIC_GPIO"); @@ -509,8 +510,7 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) debug("do_scale_vcore: volt - %d offset_code - 0x%x\n", volt_mv, offset_code); - if (omap_vc_bypass_send_value(SMPS_I2C_SLAVE_ADDR, - vcore_reg, offset_code)) + if (pmic->pmic_write(pmic->i2c_slave_addr, vcore_reg, offset_code)) printf("Scaling voltage failed for 0x%x\n", vcore_reg); if (pmic->gpio_en) @@ -525,8 +525,6 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) */ void scale_vcores(struct vcores_data const *vcores) { - omap_vc_init(PRM_VC_I2C_CHANNEL_FREQ_KHZ); - do_scale_vcore(vcores->core.addr, vcores->core.value, vcores->core.pmic); diff --git a/arch/arm/cpu/armv7/omap-common/vc.c b/arch/arm/cpu/armv7/omap-common/vc.c index e6e5f7893..a68f1d145 100644 --- a/arch/arm/cpu/armv7/omap-common/vc.c +++ b/arch/arm/cpu/armv7/omap-common/vc.c @@ -17,6 +17,7 @@ #include #include #include +#include /* * Define Master code if there are multiple masters on the I2C_SR bus. @@ -57,7 +58,7 @@ * omap_vc_init() - Initialization for Voltage controller * @speed_khz: I2C buspeed in KHz */ -void omap_vc_init(u16 speed_khz) +static void omap_vc_init(u16 speed_khz) { u32 val; u32 sys_clk_khz, cycles_hi, cycles_low; @@ -137,3 +138,14 @@ int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data) /* All good.. */ return 0; } + +void sri2c_init(void) +{ + static int sri2c = 1; + + if (sri2c) { + omap_vc_init(PRM_VC_I2C_CHANNEL_FREQ_KHZ); + sri2c = 0; + } + return; +} diff --git a/arch/arm/cpu/armv7/omap4/hw_data.c b/arch/arm/cpu/armv7/omap4/hw_data.c index 650319ad3..b97cad436 100644 --- a/arch/arm/cpu/armv7/omap4/hw_data.c +++ b/arch/arm/cpu/armv7/omap4/hw_data.c @@ -219,6 +219,9 @@ struct pmic_data twl6030_4430es1 = { .step = 12660, /* 12.66 mV represented in uV */ /* The code starts at 1 not 0 */ .start_code = 1, + .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR, + .pmic_bus_init = sri2c_init, + .pmic_write = omap_vc_bypass_send_value, }; struct pmic_data twl6030 = { @@ -226,6 +229,9 @@ struct pmic_data twl6030 = { .step = 12660, /* 12.66 mV represented in uV */ /* The code starts at 1 not 0 */ .start_code = 1, + .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR, + .pmic_bus_init = sri2c_init, + .pmic_write = omap_vc_bypass_send_value, }; struct pmic_data tps62361 = { @@ -233,7 +239,10 @@ struct pmic_data tps62361 = { .step = 10000, /* 10 mV represented in uV */ .start_code = 0, .gpio = TPS62361_VSEL0_GPIO, - .gpio_en = 1 + .gpio_en = 1, + .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR, + .pmic_bus_init = sri2c_init, + .pmic_write = omap_vc_bypass_send_value, }; struct vcores_data omap4430_volts_es1 = { diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c index d2f590001..585e31867 100644 --- a/arch/arm/cpu/armv7/omap5/hw_data.c +++ b/arch/arm/cpu/armv7/omap5/hw_data.c @@ -289,6 +289,9 @@ struct pmic_data palmas = { * Offset code 0 switches OFF the SMPS */ .start_code = 6, + .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR, + .pmic_bus_init = sri2c_init, + .pmic_write = omap_vc_bypass_send_value, }; struct vcores_data omap5430_volts = { diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index 0126a85bd..15e368224 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -57,7 +57,7 @@ u32 cortex_rev(void); void save_omap_boot_params(void); void init_omap_revision(void); void do_io_settings(void); -void omap_vc_init(u16 speed_khz); +void sri2c_init(void); int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h index fb35a82d4..91eb36cf8 100644 --- a/arch/arm/include/asm/arch-omap5/sys_proto.h +++ b/arch/arm/include/asm/arch-omap5/sys_proto.h @@ -61,7 +61,7 @@ u32 cortex_rev(void); void save_omap_boot_params(void); void init_omap_revision(void); void do_io_settings(void); -void omap_vc_init(u16 speed_khz); +void sri2c_init(void); int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index 712d78b0a..b70575b1b 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -501,6 +501,9 @@ struct pmic_data { u32 start_code; unsigned gpio; int gpio_en; + u32 i2c_slave_addr; + void (*pmic_bus_init)(void); + int (*pmic_write)(u8 sa, u8 reg_addr, u8 reg_data); }; struct volts { -- cgit v1.2.3-70-g09d2 From 63fc0c775c1eb86b9a1abb4e37311bbcf1dca008 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 30 May 2013 03:19:29 +0000 Subject: ARM: DRA7xx: power Add support for tps659038 PMIC TPS659038 is the power IC used in DRA7XX boards. Adding support for this and also adding pmic data for DRA7XX boards. Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 23 ++++++++++++++++ arch/arm/cpu/armv7/omap5/hw_data.c | 38 +++++++++++++++++++++++++- arch/arm/include/asm/arch-omap4/sys_proto.h | 1 + arch/arm/include/asm/arch-omap5/clock.h | 15 ++++++++++ arch/arm/include/asm/arch-omap5/sys_proto.h | 1 + arch/arm/include/asm/omap_common.h | 3 ++ 6 files changed, 80 insertions(+), 1 deletion(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 6c8e0632c..eda3451e7 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -30,6 +30,7 @@ * MA 02111-1307 USA */ #include +#include #include #include #include @@ -487,6 +488,9 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) u32 offset = volt_mv; int ret = 0; + if (!volt_mv) + return; + pmic->pmic_bus_init(); /* See if we can first get the GPIO if needed */ if (pmic->gpio_en) @@ -543,6 +547,15 @@ void scale_vcores(struct vcores_data const *vcores) do_scale_vcore(vcores->mm.addr, vcores->mm.value, vcores->mm.pmic); + do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, + vcores->gpu.pmic); + + do_scale_vcore(vcores->eve.addr, vcores->eve.value, + vcores->eve.pmic); + + do_scale_vcore(vcores->iva.addr, vcores->iva.value, + vcores->iva.pmic); + if (emif_sdram_type() == EMIF_SDRAM_TYPE_DDR3) { /* Configure LDO SRAM "magic" bits */ writel(2, (*prcm)->prm_sldo_core_setup); @@ -732,3 +745,13 @@ void prcm_init(void) if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context()) enable_basic_uboot_clocks(); } + +void gpi2c_init(void) +{ + static int gpi2c = 1; + + if (gpi2c) { + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + gpi2c = 0; + } +} diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c index 585e31867..90274a02c 100644 --- a/arch/arm/cpu/armv7/omap5/hw_data.c +++ b/arch/arm/cpu/armv7/omap5/hw_data.c @@ -26,6 +26,7 @@ * MA 02111-1307 USA */ #include +#include #include #include #include @@ -294,6 +295,19 @@ struct pmic_data palmas = { .pmic_write = omap_vc_bypass_send_value, }; +struct pmic_data tps659038 = { + .base_offset = PALMAS_SMPS_BASE_VOLT_UV, + .step = 10000, /* 10 mV represented in uV */ + /* + * Offset codes 1-6 all give the base voltage in Palmas + * Offset code 0 switches OFF the SMPS + */ + .start_code = 6, + .i2c_slave_addr = TPS659038_I2C_SLAVE_ADDR, + .pmic_bus_init = gpi2c_init, + .pmic_write = palmas_i2c_write_u8, +}; + struct vcores_data omap5430_volts = { .mpu.value = VDD_MPU, .mpu.addr = SMPS_REG_ADDR_12_MPU, @@ -322,6 +336,28 @@ struct vcores_data omap5430_volts_es2 = { .mm.pmic = &palmas, }; +struct vcores_data dra752_volts = { + .mpu.value = VDD_MPU_DRA752, + .mpu.addr = TPS659038_REG_ADDR_SMPS12_MPU, + .mpu.pmic = &tps659038, + + .eve.value = VDD_EVE_DRA752, + .eve.addr = TPS659038_REG_ADDR_SMPS45_EVE, + .eve.pmic = &tps659038, + + .gpu.value = VDD_GPU_DRA752, + .gpu.addr = TPS659038_REG_ADDR_SMPS6_GPU, + .gpu.pmic = &tps659038, + + .core.value = VDD_CORE_DRA752, + .core.addr = TPS659038_REG_ADDR_SMPS7_CORE, + .core.pmic = &tps659038, + + .iva.value = VDD_IVA_DRA752, + .iva.addr = TPS659038_REG_ADDR_SMPS8_IVA, + .iva.pmic = &tps659038, +}; + /* * Enable essential clock domains, modules and * do some additional special settings needed @@ -562,7 +598,7 @@ void hw_data_init(void) case DRA752_ES1_0: *prcm = &dra7xx_prcm; *dplls_data = &dra7xx_dplls; - *omap_vcores = &omap5430_volts_es2; + *omap_vcores = &dra752_volts; *ctrl = &dra7xx_ctrl; break; diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index 15e368224..e41346614 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -58,6 +58,7 @@ void save_omap_boot_params(void); void init_omap_revision(void); void do_io_settings(void); void sri2c_init(void); +void gpi2c_init(void); int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 6673a025f..f7ddd5ffe 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -212,9 +212,24 @@ #define VDD_MPU_ES2_LOW 880 #define VDD_MM_ES2_LOW 880 +/* TPS659038 Voltage settings in mv for OPP_NOMINAL */ +#define VDD_MPU_DRA752 1090 +#define VDD_EVE_DRA752 1060 +#define VDD_GPU_DRA752 1060 +#define VDD_CORE_DRA752 1030 +#define VDD_IVA_DRA752 1060 + /* Standard offset is 0.5v expressed in uv */ #define PALMAS_SMPS_BASE_VOLT_UV 500000 +/* TPS659038 */ +#define TPS659038_I2C_SLAVE_ADDR 0x58 +#define TPS659038_REG_ADDR_SMPS12_MPU 0x23 +#define TPS659038_REG_ADDR_SMPS45_EVE 0x2B +#define TPS659038_REG_ADDR_SMPS6_GPU 0x2F +#define TPS659038_REG_ADDR_SMPS7_CORE 0x33 +#define TPS659038_REG_ADDR_SMPS8_IVA 0x37 + /* TPS */ #define TPS62361_I2C_SLAVE_ADDR 0x60 #define TPS62361_REG_ADDR_SET0 0x0 diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h index 91eb36cf8..0bb59d869 100644 --- a/arch/arm/include/asm/arch-omap5/sys_proto.h +++ b/arch/arm/include/asm/arch-omap5/sys_proto.h @@ -62,6 +62,7 @@ void save_omap_boot_params(void); void init_omap_revision(void); void do_io_settings(void); void sri2c_init(void); +void gpi2c_init(void); int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index b70575b1b..3b8bece69 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -516,6 +516,9 @@ struct vcores_data { struct volts mpu; struct volts core; struct volts mm; + struct volts gpu; + struct volts eve; + struct volts iva; }; extern struct prcm_regs const **prcm; -- cgit v1.2.3-70-g09d2 From 18c9d55ac611784d161440bb9f127e372e132856 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 30 May 2013 03:19:31 +0000 Subject: ARM: OMAP5: DRA7xx: support class 0 optimized voltages DRA752 now uses AVS Class 0 voltages which are voltages in efuse. This means that we can now use the optimized voltages which are stored as mV values in efuse and program PMIC accordingly. This allows us to go with higher OPP as needed in the system without the need for implementing complex AVS logic. Signed-off-by: Nishanth Menon Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 58 ++++++++++++++++++++------ arch/arm/cpu/armv7/omap5/hw_data.c | 10 +++++ arch/arm/include/asm/arch-omap5/clock.h | 30 +++++++++++++ arch/arm/include/asm/omap_common.h | 11 +++++ 4 files changed, 97 insertions(+), 12 deletions(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 6c8226d39..9c75c13c9 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -521,6 +521,38 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) gpio_direction_output(pmic->gpio, 1); } +static u32 optimize_vcore_voltage(struct volts const *v) +{ + u32 val; + if (!v->value) + return 0; + if (!v->efuse.reg) + return v->value; + + switch (v->efuse.reg_bits) { + case 16: + val = readw(v->efuse.reg); + break; + case 32: + val = readl(v->efuse.reg); + break; + default: + printf("Error: efuse 0x%08x bits=%d unknown\n", + v->efuse.reg, v->efuse.reg_bits); + return v->value; + } + + if (!val) { + printf("Error: efuse 0x%08x bits=%d val=0, using %d\n", + v->efuse.reg, v->efuse.reg_bits, v->value); + return v->value; + } + + debug("%s:efuse 0x%08x bits=%d Vnom=%d, using efuse value %d\n", + __func__, v->efuse.reg, v->efuse.reg_bits, v->value, val); + return val; +} + /* * Setup the voltages for vdd_mpu, vdd_core, and vdd_iva * We set the maximum voltages allowed here because Smart-Reflex is not @@ -529,11 +561,13 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) */ void scale_vcores(struct vcores_data const *vcores) { - do_scale_vcore(vcores->core.addr, vcores->core.value, - vcores->core.pmic); + u32 val; + + val = optimize_vcore_voltage(&vcores->core); + do_scale_vcore(vcores->core.addr, val, vcores->core.pmic); - do_scale_vcore(vcores->mpu.addr, vcores->mpu.value, - vcores->mpu.pmic); + val = optimize_vcore_voltage(&vcores->mpu); + do_scale_vcore(vcores->mpu.addr, val, vcores->mpu.pmic); /* Configure MPU ABB LDO after scale */ abb_setup((*ctrl)->control_std_fuse_opp_vdd_mpu_2, @@ -544,17 +578,17 @@ void scale_vcores(struct vcores_data const *vcores) OMAP_ABB_MPU_TXDONE_MASK, OMAP_ABB_FAST_OPP); - do_scale_vcore(vcores->mm.addr, vcores->mm.value, - vcores->mm.pmic); + val = optimize_vcore_voltage(&vcores->mm); + do_scale_vcore(vcores->mm.addr, val, vcores->mm.pmic); - do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, - vcores->gpu.pmic); + val = optimize_vcore_voltage(&vcores->gpu); + do_scale_vcore(vcores->gpu.addr, val, vcores->gpu.pmic); - do_scale_vcore(vcores->eve.addr, vcores->eve.value, - vcores->eve.pmic); + val = optimize_vcore_voltage(&vcores->eve); + do_scale_vcore(vcores->eve.addr, val, vcores->eve.pmic); - do_scale_vcore(vcores->iva.addr, vcores->iva.value, - vcores->iva.pmic); + val = optimize_vcore_voltage(&vcores->iva); + do_scale_vcore(vcores->iva.addr, val, vcores->iva.pmic); if (emif_sdram_type() == EMIF_SDRAM_TYPE_DDR3) { /* Configure LDO SRAM "magic" bits */ diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c index 90274a02c..bddcaed17 100644 --- a/arch/arm/cpu/armv7/omap5/hw_data.c +++ b/arch/arm/cpu/armv7/omap5/hw_data.c @@ -338,22 +338,32 @@ struct vcores_data omap5430_volts_es2 = { struct vcores_data dra752_volts = { .mpu.value = VDD_MPU_DRA752, + .mpu.efuse.reg = STD_FUSE_OPP_VMIN_MPU_NOM, + .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, .mpu.addr = TPS659038_REG_ADDR_SMPS12_MPU, .mpu.pmic = &tps659038, .eve.value = VDD_EVE_DRA752, + .eve.efuse.reg = STD_FUSE_OPP_VMIN_DSPEVE_NOM, + .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, .eve.addr = TPS659038_REG_ADDR_SMPS45_EVE, .eve.pmic = &tps659038, .gpu.value = VDD_GPU_DRA752, + .gpu.efuse.reg = STD_FUSE_OPP_VMIN_GPU_NOM, + .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, .gpu.addr = TPS659038_REG_ADDR_SMPS6_GPU, .gpu.pmic = &tps659038, .core.value = VDD_CORE_DRA752, + .core.efuse.reg = STD_FUSE_OPP_VMIN_CORE_NOM, + .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, .core.addr = TPS659038_REG_ADDR_SMPS7_CORE, .core.pmic = &tps659038, .iva.value = VDD_IVA_DRA752, + .iva.efuse.reg = STD_FUSE_OPP_VMIN_IVA_NOM, + .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, .iva.addr = TPS659038_REG_ADDR_SMPS8_IVA, .iva.pmic = &tps659038, }; diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index f7ddd5ffe..6d02835ea 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -219,6 +219,36 @@ #define VDD_CORE_DRA752 1030 #define VDD_IVA_DRA752 1060 +/* Efuse register offsets for DRA7xx platform */ +#define DRA752_EFUSE_BASE 0x4A002000 +#define DRA752_EFUSE_REGBITS 16 +/* STD_FUSE_OPP_VMIN_IVA_2 */ +#define STD_FUSE_OPP_VMIN_IVA_NOM (DRA752_EFUSE_BASE + 0x05CC) +/* STD_FUSE_OPP_VMIN_IVA_3 */ +#define STD_FUSE_OPP_VMIN_IVA_OD (DRA752_EFUSE_BASE + 0x05D0) +/* STD_FUSE_OPP_VMIN_IVA_4 */ +#define STD_FUSE_OPP_VMIN_IVA_HIGH (DRA752_EFUSE_BASE + 0x05D4) +/* STD_FUSE_OPP_VMIN_DSPEVE_2 */ +#define STD_FUSE_OPP_VMIN_DSPEVE_NOM (DRA752_EFUSE_BASE + 0x05E0) +/* STD_FUSE_OPP_VMIN_DSPEVE_3 */ +#define STD_FUSE_OPP_VMIN_DSPEVE_OD (DRA752_EFUSE_BASE + 0x05E4) +/* STD_FUSE_OPP_VMIN_DSPEVE_4 */ +#define STD_FUSE_OPP_VMIN_DSPEVE_HIGH (DRA752_EFUSE_BASE + 0x05E8) +/* STD_FUSE_OPP_VMIN_CORE_2 */ +#define STD_FUSE_OPP_VMIN_CORE_NOM (DRA752_EFUSE_BASE + 0x05F4) +/* STD_FUSE_OPP_VMIN_GPU_2 */ +#define STD_FUSE_OPP_VMIN_GPU_NOM (DRA752_EFUSE_BASE + 0x1B08) +/* STD_FUSE_OPP_VMIN_GPU_3 */ +#define STD_FUSE_OPP_VMIN_GPU_OD (DRA752_EFUSE_BASE + 0x1B0C) +/* STD_FUSE_OPP_VMIN_GPU_4 */ +#define STD_FUSE_OPP_VMIN_GPU_HIGH (DRA752_EFUSE_BASE + 0x1B10) +/* STD_FUSE_OPP_VMIN_MPU_2 */ +#define STD_FUSE_OPP_VMIN_MPU_NOM (DRA752_EFUSE_BASE + 0x1B20) +/* STD_FUSE_OPP_VMIN_MPU_3 */ +#define STD_FUSE_OPP_VMIN_MPU_OD (DRA752_EFUSE_BASE + 0x1B24) +/* STD_FUSE_OPP_VMIN_MPU_4 */ +#define STD_FUSE_OPP_VMIN_MPU_HIGH (DRA752_EFUSE_BASE + 0x1B28) + /* Standard offset is 0.5v expressed in uv */ #define PALMAS_SMPS_BASE_VOLT_UV 500000 diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index 3b8bece69..f51fccce5 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -506,9 +506,20 @@ struct pmic_data { int (*pmic_write)(u8 sa, u8 reg_addr, u8 reg_data); }; +/** + * struct volts_efuse_data - efuse definition for voltage + * @reg: register address for efuse + * @reg_bits: Number of bits in a register address, mandatory. + */ +struct volts_efuse_data { + u32 reg; + u8 reg_bits; +}; + struct volts { u32 value; u32 addr; + struct volts_efuse_data efuse; struct pmic_data *pmic; }; -- cgit v1.2.3-70-g09d2 From e9d6cd042d63d59a43dfe953d488cfbf1ece516c Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 30 May 2013 03:19:32 +0000 Subject: ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc's Slew rate compensation cells are not present for DRA7xx Soc's. So return from function srcomp_enable() if soc is not OMAP54xx. Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap5/hwinit.c | 3 +++ arch/arm/include/asm/omap_common.h | 8 ++++++++ 2 files changed, 11 insertions(+) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c index afb700022..40dbf4570 100644 --- a/arch/arm/cpu/armv7/omap5/hwinit.c +++ b/arch/arm/cpu/armv7/omap5/hwinit.c @@ -201,6 +201,9 @@ void srcomp_enable(void) u32 sysclk_ind = get_sys_clk_index(); u32 omap_rev = omap_revision(); + if (!is_omap54xx()) + return; + mul_factor = srcomp_parameters[sysclk_ind].multiply_factor; div_factor = srcomp_parameters[sysclk_ind].divide_factor; diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index f51fccce5..f33f28baf 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -597,6 +597,14 @@ static inline u32 omap_revision(void) extern u32 *const omap_si_rev; return *omap_si_rev; } + +#define OMAP54xx 0x54000000 + +static inline u8 is_omap54xx(void) +{ + extern u32 *const omap_si_rev; + return ((*omap_si_rev & 0xFF000000) == OMAP54xx); +} #endif /* -- cgit v1.2.3-70-g09d2 From 97405d843ece2a53e67b801e02ee42005d26e172 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 30 May 2013 03:19:38 +0000 Subject: ARM: DRA7xx: clocks: Update PLL values Update PLL values. SYS_CLKSEL value for 20MHz is changed to 2. In other platforms SYS_CLKSEL value 2 represents reserved. But in sys_clk array ind 1 is used for 13Mhz. Since other platforms are not using 13Mhz, reusing index 1 for 20MHz. Signed-off-by: Lokesh Vutla Signed-off-by: Sricharan R --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 16 +++-- arch/arm/cpu/armv7/omap5/hw_data.c | 87 ++++++++++++++++---------- arch/arm/cpu/armv7/omap5/prcm-regs.c | 1 + arch/arm/include/asm/arch-omap4/clock.h | 2 +- arch/arm/include/asm/arch-omap5/clock.h | 8 ++- arch/arm/include/asm/omap_common.h | 3 +- include/configs/dra7xx_evm.h | 2 + 7 files changed, 73 insertions(+), 46 deletions(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 9c75c13c9..ef23127bb 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -50,13 +50,12 @@ const u32 sys_clk_array[8] = { 12000000, /* 12 MHz */ - 13000000, /* 13 MHz */ + 20000000, /* 20 MHz */ 16800000, /* 16.8 MHz */ 19200000, /* 19.2 MHz */ 26000000, /* 26 MHz */ 27000000, /* 27 MHz */ 38400000, /* 38.4 MHz */ - 20000000, /* 20 MHz */ }; static inline u32 __get_sys_clk_index(void) @@ -75,13 +74,6 @@ static inline u32 __get_sys_clk_index(void) /* SYS_CLKSEL - 1 to match the dpll param array indices */ ind = (readl((*prcm)->cm_sys_clksel) & CM_SYS_CLKSEL_SYS_CLKSEL_MASK) - 1; - /* - * SYS_CLKSEL value for 20MHz is 0. This is introduced newly - * in DRA7XX socs. SYS_CLKSEL -1 will be greater than - * NUM_SYS_CLK. So considering the last 3 bits as the index - * for the dpll param array. - */ - ind &= CM_SYS_CLKSEL_SYS_CLKSEL_MASK; } return ind; } @@ -441,6 +433,12 @@ static void setup_non_essential_dplls(void) params = get_abe_dpll_params(*dplls_data); #ifdef CONFIG_SYS_OMAP_ABE_SYSCK abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK; + + if (omap_revision() == DRA752_ES1_0) + /* Select the sys clk for dpll_abe */ + clrsetbits_le32((*prcm)->cm_abe_pll_sys_clksel, + CM_CLKSEL_ABE_PLL_SYS_CLKSEL_MASK, + CM_ABE_PLL_SYS_CLKSEL_SYSCLK2); #else abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK; /* diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c index bddcaed17..44552c342 100644 --- a/arch/arm/cpu/armv7/omap5/hw_data.c +++ b/arch/arm/cpu/armv7/omap5/hw_data.c @@ -100,14 +100,13 @@ static const struct dpll_params mpu_dpll_params_499mhz[NUM_SYS_CLKS] = { }; static const struct dpll_params mpu_dpll_params_1ghz[NUM_SYS_CLKS] = { - {250, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ - {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */ - {119, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ - {625, 11, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ - {500, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ + {250, 2, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ + {500, 9, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 20 MHz */ + {119, 1, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ + {625, 11, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ + {500, 12, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ - {625, 23, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ - {50, 0, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 20 MHz */ + {625, 23, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ }; static const struct dpll_params @@ -133,15 +132,14 @@ static const struct dpll_params }; static const struct dpll_params - core_dpll_params_2128mhz_ddr532_dra7xx[NUM_SYS_CLKS] = { - {266, 2, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6}, /* 12 MHz */ - {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */ - {443, 6, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6}, /* 16.8 MHz */ - {277, 4, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6}, /* 19.2 MHz */ - {368, 8, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6}, /* 26 MHz */ + core_dpll_params_2128mhz_dra7xx[NUM_SYS_CLKS] = { + {266, 2, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 12 MHz */ + {266, 4, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 20 MHz */ + {443, 6, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 16.8 MHz */ + {277, 4, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 19.2 MHz */ + {368, 8, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 26 MHz */ {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ - {277, 9, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6}, /* 38.4 MHz */ - {266, 4, 2, -1, -1, 4, 62, 5, -1, 5, 7, 6} /* 20 MHz */ + {277, 9, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6}, /* 38.4 MHz */ }; static const struct dpll_params @@ -187,14 +185,13 @@ static const struct dpll_params per_dpll_params_768mhz_es2[NUM_SYS_CLKS] = { }; static const struct dpll_params per_dpll_params_768mhz_dra7xx[NUM_SYS_CLKS] = { - {32, 0, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 12 MHz */ - {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */ - {160, 6, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 16.8 MHz */ - {20, 0, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 19.2 MHz */ - {192, 12, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 26 MHz */ + {32, 0, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 12 MHz */ + {96, 4, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 20 MHz */ + {160, 6, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 16.8 MHz */ + {20, 0, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 19.2 MHz */ + {192, 12, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 26 MHz */ {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ - {10, 0, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 38.4 MHz */ - {96, 4, 4, -1, 3, 4, 10, 2, -1, -1, -1, -1} /* 20 MHz */ + {10, 0, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1}, /* 38.4 MHz */ }; static const struct dpll_params iva_dpll_params_2330mhz[NUM_SYS_CLKS] = { @@ -207,6 +204,16 @@ static const struct dpll_params iva_dpll_params_2330mhz[NUM_SYS_CLKS] = { {91, 2, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */ }; +static const struct dpll_params iva_dpll_params_2330mhz_dra7xx[NUM_SYS_CLKS] = { + {1165, 11, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ + {233, 3, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 20 MHz */ + {208, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ + {182, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ + {224, 4, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ + {91, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ +}; + /* ABE M & N values with sys_clk as source */ static const struct dpll_params abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = { @@ -224,26 +231,36 @@ static const struct dpll_params abe_dpll_params_32k_196608khz = { 750, 0, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1 }; +/* ABE M & N values with sysclk2(22.5792 MHz) as input */ +static const struct dpll_params + abe_dpll_params_sysclk2_361267khz[NUM_SYS_CLKS] = { + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ + {16, 1, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 20 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ + {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ +}; + static const struct dpll_params usb_dpll_params_1920mhz[NUM_SYS_CLKS] = { {400, 4, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ - {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */ + {480, 9, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 20 MHz */ {400, 6, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ {400, 7, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ {480, 12, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ {400, 15, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ - {48, 0, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 20 MHz */ }; -static const struct dpll_params ddr_dpll_params_1066mhz[NUM_SYS_CLKS] = { - {533, 11, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ - {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */ - {222, 6, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ - {111, 3, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ - {41, 1, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ +static const struct dpll_params ddr_dpll_params_2128mhz[NUM_SYS_CLKS] = { + {266, 2, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */ + {266, 4, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 20 MHz */ + {190, 2, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */ + {665, 11, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */ + {532, 12, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */ {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */ - {347, 24, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ - {533, 19, 1, 1, 4, -1, -1, -1, -1, -1, -1, -1} /* 20 MHz */ + {665, 23, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1}, /* 38.4 MHz */ }; struct dplls omap5_dplls_es1 = { @@ -276,10 +293,12 @@ struct dplls omap5_dplls_es2 = { struct dplls dra7xx_dplls = { .mpu = mpu_dpll_params_1ghz, - .core = core_dpll_params_2128mhz_ddr532_dra7xx, + .core = core_dpll_params_2128mhz_dra7xx, .per = per_dpll_params_768mhz_dra7xx, + .abe = abe_dpll_params_sysclk2_361267khz, + .iva = iva_dpll_params_2330mhz_dra7xx, .usb = usb_dpll_params_1920mhz, - .ddr = ddr_dpll_params_1066mhz, + .ddr = ddr_dpll_params_2128mhz, }; struct pmic_data palmas = { diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index f3b315516..b7c2f98dd 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -951,6 +951,7 @@ struct prcm_regs const dra7xx_prcm = { /* l4 wkup regs */ .cm_abe_pll_ref_clksel = 0x4ae0610c, .cm_sys_clksel = 0x4ae06110, + .cm_abe_pll_sys_clksel = 0x4ae06118, .cm_wkup_clkstctrl = 0x4ae07800, .cm_wkup_l4wkup_clkctrl = 0x4ae07820, .cm_wkup_wdtimer1_clkctrl = 0x4ae07828, diff --git a/arch/arm/include/asm/arch-omap4/clock.h b/arch/arm/include/asm/arch-omap4/clock.h index d7b61c298..d14d8fb8a 100644 --- a/arch/arm/include/asm/arch-omap4/clock.h +++ b/arch/arm/include/asm/arch-omap4/clock.h @@ -76,7 +76,7 @@ #define CM_CLKSEL_DCC_EN_MASK (1 << 22) /* CM_SYS_CLKSEL */ -#define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 +#define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 /* CM_CLKSEL_CORE */ #define CLKSEL_CORE_SHIFT 0 diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 86d4711a1..1affa4f66 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -81,7 +81,7 @@ #define CM_CLKSEL_DCC_EN_MASK (1 << 22) /* CM_SYS_CLKSEL */ -#define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 +#define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7 /* CM_CLKSEL_CORE */ #define CLKSEL_CORE_SHIFT 0 @@ -98,6 +98,12 @@ #define CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK 0 #define CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK 1 +/* CM_CLKSEL_ABE_PLL_SYS */ +#define CM_CLKSEL_ABE_PLL_SYS_CLKSEL_SHIFT 0 +#define CM_CLKSEL_ABE_PLL_SYS_CLKSEL_MASK 1 +#define CM_ABE_PLL_SYS_CLKSEL_SYSCLK1 0 +#define CM_ABE_PLL_SYS_CLKSEL_SYSCLK2 1 + /* CM_BYPCLK_DPLL_IVA */ #define CM_BYPCLK_DPLL_IVA_CLKSEL_SHIFT 0 #define CM_BYPCLK_DPLL_IVA_CLKSEL_MASK 3 diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index f33f28baf..d5daa27d1 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -29,7 +29,7 @@ #include -#define NUM_SYS_CLKS 8 +#define NUM_SYS_CLKS 7 struct prcm_regs { /* cm1.ckgen */ @@ -303,6 +303,7 @@ struct prcm_regs { /* l4 wkup regs */ u32 cm_abe_pll_ref_clksel; u32 cm_sys_clksel; + u32 cm_abe_pll_sys_clksel; u32 cm_wkup_clkstctrl; u32 cm_wkup_l4wkup_clkctrl; u32 cm_wkup_wdtimer1_clkctrl; diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 35dec08a4..0eea28c80 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -39,4 +39,6 @@ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550_COM1 UART1_BASE #define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_OMAP_ABE_SYSCK #endif /* __CONFIG_DRA7XX_EVM_H */ -- cgit v1.2.3-70-g09d2 From 92b0482c17acf92f94ac74fd8536fd95d5b64b5e Mon Sep 17 00:00:00 2001 From: Sricharan R Date: Thu, 30 May 2013 03:19:39 +0000 Subject: ARM: DRA7xx: EMIF: Change settings required for EVM board DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R Signed-off-by: Lokesh Vutla --- arch/arm/cpu/armv7/omap-common/emif-common.c | 26 +++- arch/arm/cpu/armv7/omap5/hw_data.c | 21 +++- arch/arm/cpu/armv7/omap5/hwinit.c | 19 +-- arch/arm/cpu/armv7/omap5/prcm-regs.c | 1 + arch/arm/cpu/armv7/omap5/sdram.c | 170 +++++++++++++++++++++++++-- arch/arm/include/asm/arch-omap5/omap.h | 1 + arch/arm/include/asm/emif.h | 12 +- arch/arm/include/asm/omap_common.h | 1 + 8 files changed, 220 insertions(+), 31 deletions(-) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap-common/emif-common.c b/arch/arm/cpu/armv7/omap-common/emif-common.c index 882396759..652e5a71b 100644 --- a/arch/arm/cpu/armv7/omap-common/emif-common.c +++ b/arch/arm/cpu/armv7/omap-common/emif-common.c @@ -209,7 +209,8 @@ void emif_update_timings(u32 base, const struct emif_regs *regs) writel(regs->temp_alert_config, &emif->emif_temp_alert_config); writel(regs->emif_ddr_phy_ctlr_1, &emif->emif_ddr_phy_ctrl_1_shdw); - if (omap_revision() >= OMAP5430_ES1_0) { + if ((omap_revision() >= OMAP5430_ES1_0) || + (omap_revision() == DRA752_ES1_0)) { writel(EMIF_L3_CONFIG_VAL_SYS_10_MPU_5_LL_0, &emif->emif_l3_config); } else if (omap_revision() >= OMAP4460_ES1_0) { @@ -263,6 +264,18 @@ static void ddr3_leveling(u32 base, const struct emif_regs *regs) __udelay(130); } +static void ddr3_sw_leveling(u32 base, const struct emif_regs *regs) +{ + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; + + writel(regs->emif_ddr_phy_ctlr_1, &emif->emif_ddr_phy_ctrl_1); + writel(regs->emif_ddr_phy_ctlr_1, &emif->emif_ddr_phy_ctrl_1_shdw); + config_data_eye_leveling_samples(base); + + writel(regs->emif_rd_wr_lvl_ctl, &emif->emif_rd_wr_lvl_ctl); + writel(regs->sdram_config, &emif->emif_sdram_config); +} + static void ddr3_init(u32 base, const struct emif_regs *regs) { struct emif_reg_struct *emif = (struct emif_reg_struct *)base; @@ -273,6 +286,7 @@ static void ddr3_init(u32 base, const struct emif_regs *regs) * defined, contents of mode Registers must be fully initialized. * H/W takes care of this initialization */ + writel(regs->sdram_config2, &emif->emif_lpddr2_nvm_config); writel(regs->sdram_config_init, &emif->emif_sdram_config); writel(regs->emif_ddr_phy_ctlr_1_init, &emif->emif_ddr_phy_ctrl_1); @@ -290,7 +304,10 @@ static void ddr3_init(u32 base, const struct emif_regs *regs) /* enable leveling */ writel(regs->emif_rd_wr_lvl_rmp_ctl, &emif->emif_rd_wr_lvl_rmp_ctl); - ddr3_leveling(base, regs); + if (omap_revision() == DRA752_ES1_0) + ddr3_sw_leveling(base, regs); + else + ddr3_leveling(base, regs); } #ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS @@ -1078,7 +1095,10 @@ static void do_sdram_init(u32 base) if (warm_reset() && (emif_sdram_type() == EMIF_SDRAM_TYPE_DDR3)) { set_lpmode_selfrefresh(base); emif_reset_phy(base); - ddr3_leveling(base, regs); + if (omap_revision() == DRA752_ES1_0) + ddr3_sw_leveling(base, regs); + else + ddr3_leveling(base, regs); } /* Write to the shadow registers */ diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c index 44552c342..56cf1f8c6 100644 --- a/arch/arm/cpu/armv7/omap5/hw_data.c +++ b/arch/arm/cpu/armv7/omap5/hw_data.c @@ -602,6 +602,17 @@ const struct ctrl_ioregs ioregs_omap5432_es2 = { .ctrl_emif_sdram_config_ext = SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES, }; +const struct ctrl_ioregs ioregs_dra7xx_es1 = { + .ctrl_ddrch = 0x40404040, + .ctrl_lpddr2ch = 0x40404040, + .ctrl_ddr3ch = 0x80808080, + .ctrl_ddrio_0 = 0xbae8c631, + .ctrl_ddrio_1 = 0xb46318d8, + .ctrl_ddrio_2 = 0x84210000, + .ctrl_emif_sdram_config_ext = 0xb2c00000, + .ctrl_ddr_ctrl_ext_0 = 0xA2000000, +}; + void hw_data_init(void) { u32 omap_rev = omap_revision(); @@ -644,14 +655,16 @@ void get_ioregs(const struct ctrl_ioregs **regs) case OMAP5430_ES1_0: case OMAP5430_ES2_0: *regs = &ioregs_omap5430; - break; + break; case OMAP5432_ES1_0: *regs = &ioregs_omap5432_es1; - break; + break; case OMAP5432_ES2_0: - case DRA752_ES1_0: *regs = &ioregs_omap5432_es2; - break; + break; + case DRA752_ES1_0: + *regs = &ioregs_dra7xx_es1; + break; default: printf("\n INVALID OMAP REVISION "); diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c index 40dbf4570..daf124e99 100644 --- a/arch/arm/cpu/armv7/omap5/hwinit.c +++ b/arch/arm/cpu/armv7/omap5/hwinit.c @@ -100,16 +100,21 @@ static void io_settings_ddr3(void) writel(ioregs->ctrl_emif_sdram_config_ext, (*ctrl)->control_emif2_sdram_config_ext); - /* Disable DLL select */ - io_settings = (readl((*ctrl)->control_port_emif1_sdram_config) + if (is_omap54xx()) { + /* Disable DLL select */ + io_settings = (readl((*ctrl)->control_port_emif1_sdram_config) & 0xFFEFFFFF); - writel(io_settings, - (*ctrl)->control_port_emif1_sdram_config); + writel(io_settings, + (*ctrl)->control_port_emif1_sdram_config); - io_settings = (readl((*ctrl)->control_port_emif2_sdram_config) + io_settings = (readl((*ctrl)->control_port_emif2_sdram_config) & 0xFFEFFFFF); - writel(io_settings, - (*ctrl)->control_port_emif2_sdram_config); + writel(io_settings, + (*ctrl)->control_port_emif2_sdram_config); + } else { + writel(ioregs->ctrl_ddr_ctrl_ext_0, + (*ctrl)->control_ddr_control_ext_0); + } } /* diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index b7c2f98dd..5a7370c77 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -439,6 +439,7 @@ struct omap_sys_ctrl_regs const dra7xx_ctrl = { .control_srcomp_east_side = 0x4A002E7C, .control_srcomp_west_side = 0x4A002E80, .control_srcomp_code_latch = 0x4A002E84, + .control_ddr_control_ext_0 = 0x4A002E88, .control_padconf_core_base = 0x4A003400, .control_port_emif1_sdram_config = 0x4AE0C110, .control_port_emif1_lpddr2_nvm_config = 0x4AE0C114, diff --git a/arch/arm/cpu/armv7/omap5/sdram.c b/arch/arm/cpu/armv7/omap5/sdram.c index 6b461e484..1b445a61e 100644 --- a/arch/arm/cpu/armv7/omap5/sdram.c +++ b/arch/arm/cpu/armv7/omap5/sdram.c @@ -108,6 +108,7 @@ const struct emif_regs emif_regs_266_mhz_2cs = { const struct emif_regs emif_regs_ddr3_532_mhz_1cs = { .sdram_config_init = 0x61851B32, .sdram_config = 0x61851B32, + .sdram_config2 = 0x0, .ref_ctrl = 0x00001035, .sdram_tim1 = 0xCCCF36B3, .sdram_tim2 = 0x308F7FDA, @@ -131,6 +132,7 @@ const struct emif_regs emif_regs_ddr3_532_mhz_1cs = { const struct emif_regs emif_regs_ddr3_532_mhz_1cs_es2 = { .sdram_config_init = 0x61851B32, .sdram_config = 0x61851B32, + .sdram_config2 = 0x0, .ref_ctrl = 0x00001035, .sdram_tim1 = 0xCCCF36B3, .sdram_tim2 = 0x308F7FDA, @@ -151,6 +153,54 @@ const struct emif_regs emif_regs_ddr3_532_mhz_1cs_es2 = { .emif_rd_wr_exec_thresh = 0x40000305 }; +const struct emif_regs emif_1_regs_ddr3_532_mhz_1cs_dra_es1 = { + .sdram_config_init = 0x61851ab2, + .sdram_config = 0x61851ab2, + .sdram_config2 = 0x08000000, + .ref_ctrl = 0x00001035, + .sdram_tim1 = 0xCCCF36B3, + .sdram_tim2 = 0x308F7FDA, + .sdram_tim3 = 0x027F88A8, + .read_idle_ctrl = 0x00050000, + .zq_config = 0x0007190B, + .temp_alert_config = 0x00000000, + .emif_ddr_phy_ctlr_1_init = 0x0E20400A, + .emif_ddr_phy_ctlr_1 = 0x0E24400A, + .emif_ddr_ext_phy_ctrl_1 = 0x04040100, + .emif_ddr_ext_phy_ctrl_2 = 0x009E009E, + .emif_ddr_ext_phy_ctrl_3 = 0x009E009E, + .emif_ddr_ext_phy_ctrl_4 = 0x009E009E, + .emif_ddr_ext_phy_ctrl_5 = 0x009E009E, + .emif_rd_wr_lvl_rmp_win = 0x00000000, + .emif_rd_wr_lvl_rmp_ctl = 0x80000000, + .emif_rd_wr_lvl_ctl = 0x00000000, + .emif_rd_wr_exec_thresh = 0x00000305 +}; + +const struct emif_regs emif_2_regs_ddr3_532_mhz_1cs_dra_es1 = { + .sdram_config_init = 0x61851B32, + .sdram_config = 0x61851B32, + .sdram_config2 = 0x08000000, + .ref_ctrl = 0x00001035, + .sdram_tim1 = 0xCCCF36B3, + .sdram_tim2 = 0x308F7FDA, + .sdram_tim3 = 0x027F88A8, + .read_idle_ctrl = 0x00050000, + .zq_config = 0x0007190B, + .temp_alert_config = 0x00000000, + .emif_ddr_phy_ctlr_1_init = 0x0020400A, + .emif_ddr_phy_ctlr_1 = 0x0E24400A, + .emif_ddr_ext_phy_ctrl_1 = 0x04040100, + .emif_ddr_ext_phy_ctrl_2 = 0x009D009D, + .emif_ddr_ext_phy_ctrl_3 = 0x009D009D, + .emif_ddr_ext_phy_ctrl_4 = 0x009D009D, + .emif_ddr_ext_phy_ctrl_5 = 0x009D009D, + .emif_rd_wr_lvl_rmp_win = 0x00000000, + .emif_rd_wr_lvl_rmp_ctl = 0x80000000, + .emif_rd_wr_lvl_ctl = 0x00000000, + .emif_rd_wr_exec_thresh = 0x00000305 +}; + const struct dmm_lisa_map_regs lisa_map_4G_x_2_x_2 = { .dmm_lisa_map_0 = 0x0, .dmm_lisa_map_1 = 0x0, @@ -159,11 +209,39 @@ const struct dmm_lisa_map_regs lisa_map_4G_x_2_x_2 = { .is_ma_present = 0x1 }; -const struct dmm_lisa_map_regs lisa_map_512M_x_1 = { +/* + * DRA752 EVM board has 1.5 GB of memory + * EMIF1 --> 2Gb * 2 = 512MB + * EMIF2 --> 2Gb * 4 = 1GB + * so mapping 1GB interleaved and 512MB non-interleaved + */ +const struct dmm_lisa_map_regs lisa_map_2G_x_2_x_2_2G_x_1_x_2 = { + .dmm_lisa_map_0 = 0x0, + .dmm_lisa_map_1 = 0x80640300, + .dmm_lisa_map_2 = 0xC0500220, + .dmm_lisa_map_3 = 0xFF020100, + .is_ma_present = 0x1 +}; + +/* + * DRA752 EVM EMIF1 ONLY CONFIGURATION + */ +const struct dmm_lisa_map_regs lisa_map_2G_x_1_x_2 = { .dmm_lisa_map_0 = 0x0, .dmm_lisa_map_1 = 0x0, - .dmm_lisa_map_2 = 0x0, - .dmm_lisa_map_3 = 0x80500100, + .dmm_lisa_map_2 = 0x80500100, + .dmm_lisa_map_3 = 0xFF020100, + .is_ma_present = 0x1 +}; + +/* + * DRA752 EVM EMIF2 ONLY CONFIGURATION + */ +const struct dmm_lisa_map_regs lisa_map_2G_x_2_x_2 = { + .dmm_lisa_map_0 = 0x0, + .dmm_lisa_map_1 = 0x0, + .dmm_lisa_map_2 = 0x80600200, + .dmm_lisa_map_3 = 0xFF020100, .is_ma_present = 0x1 }; @@ -180,9 +258,20 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_532_mhz_2cs_es2; break; case OMAP5432_ES2_0: + *regs = &emif_regs_ddr3_532_mhz_1cs_es2; + break; case DRA752_ES1_0: + switch (emif_nr) { + case 1: + *regs = &emif_1_regs_ddr3_532_mhz_1cs_dra_es1; + break; + case 2: + *regs = &emif_2_regs_ddr3_532_mhz_1cs_dra_es1; + break; + } + break; default: - *regs = &emif_regs_ddr3_532_mhz_1cs_es2; + *regs = &emif_1_regs_ddr3_532_mhz_1cs_dra_es1; } } @@ -201,7 +290,7 @@ static void emif_get_dmm_regs_sdp(const struct dmm_lisa_map_regs break; case DRA752_ES1_0: default: - *dmm_lisa_regs = &lisa_map_512M_x_1; + *dmm_lisa_regs = &lisa_map_2G_x_2_x_2_2G_x_1_x_2; } } @@ -252,7 +341,8 @@ const u32 ext_phy_ctrl_const_base[EMIF_EXT_PHY_CTRL_CONST_REG] = { 0x00000000, 0x00000000, 0x00000000, - 0x00000077 + 0x00000077, + 0x0 }; const u32 ddr3_ext_phy_ctrl_const_base_es1[EMIF_EXT_PHY_CTRL_CONST_REG] = { @@ -274,7 +364,8 @@ const u32 ddr3_ext_phy_ctrl_const_base_es1[EMIF_EXT_PHY_CTRL_CONST_REG] = { 0x00000000, 0x00000000, 0x00000000, - 0x00000057 + 0x00000057, + 0x0 }; const u32 ddr3_ext_phy_ctrl_const_base_es2[EMIF_EXT_PHY_CTRL_CONST_REG] = { @@ -296,7 +387,56 @@ const u32 ddr3_ext_phy_ctrl_const_base_es2[EMIF_EXT_PHY_CTRL_CONST_REG] = { 0x00000000, 0x00000000, 0x00000000, - 0x00000057 + 0x00000057, + 0x0 +}; + +const u32 +dra_ddr3_ext_phy_ctrl_const_base_es1_emif1[EMIF_EXT_PHY_CTRL_CONST_REG] = { + 0x009E009E, + 0x002E002E, + 0x002E002E, + 0x002E002E, + 0x002E002E, + 0x002E002E, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x004D004D, + 0x0, + 0x600020, + 0x40010080, + 0x8102040 +}; + +const u32 +dra_ddr3_ext_phy_ctrl_const_base_es1_emif2[EMIF_EXT_PHY_CTRL_CONST_REG] = { + 0x009D009D, + 0x002D002D, + 0x002D002D, + 0x002D002D, + 0x002D002D, + 0x002D002D, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x00570057, + 0x0, + 0x600020, + 0x40010080, + 0x8102040 }; const struct lpddr2_mr_regs mr_regs = { @@ -307,7 +447,7 @@ const struct lpddr2_mr_regs mr_regs = { .mr16 = MR16_REF_FULL_ARRAY }; -static void emif_get_ext_phy_ctrl_const_regs(const u32 **regs) +static void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs) { switch (omap_revision()) { case OMAP5430_ES1_0: @@ -318,7 +458,14 @@ static void emif_get_ext_phy_ctrl_const_regs(const u32 **regs) *regs = ddr3_ext_phy_ctrl_const_base_es1; break; case OMAP5432_ES2_0: + *regs = ddr3_ext_phy_ctrl_const_base_es2; + break; case DRA752_ES1_0: + if (emif_nr == 1) + *regs = dra_ddr3_ext_phy_ctrl_const_base_es1_emif1; + else + *regs = dra_ddr3_ext_phy_ctrl_const_base_es1_emif2; + break; default: *regs = ddr3_ext_phy_ctrl_const_base_es2; @@ -334,9 +481,12 @@ void do_ext_phy_settings(u32 base, const struct emif_regs *regs) { u32 *ext_phy_ctrl_base = 0; u32 *emif_ext_phy_ctrl_base = 0; + u32 emif_nr; const u32 *ext_phy_ctrl_const_regs; u32 i = 0; + emif_nr = (base == EMIF1_BASE) ? 1 : 2; + struct emif_reg_struct *emif = (struct emif_reg_struct *)base; ext_phy_ctrl_base = (u32 *) &(regs->emif_ddr_ext_phy_ctrl_1); @@ -353,7 +503,7 @@ void do_ext_phy_settings(u32 base, const struct emif_regs *regs) * external phy 6-24 registers do not change with * ddr frequency */ - emif_get_ext_phy_ctrl_const_regs(&ext_phy_ctrl_const_regs); + emif_get_ext_phy_ctrl_const_regs(emif_nr, &ext_phy_ctrl_const_regs); for (i = 0; i < EMIF_EXT_PHY_CTRL_CONST_REG; i++) { writel(ext_phy_ctrl_const_regs[i], emif_ext_phy_ctrl_base++); diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h index bb6a757dc..817c1ff27 100644 --- a/arch/arm/include/asm/arch-omap5/omap.h +++ b/arch/arm/include/asm/arch-omap5/omap.h @@ -221,6 +221,7 @@ struct ctrl_ioregs { u32 ctrl_ddrio_1; u32 ctrl_ddrio_2; u32 ctrl_emif_sdram_config_ext; + u32 ctrl_ddr_ctrl_ext_0; }; #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm/include/asm/emif.h b/arch/arm/include/asm/emif.h index 5f11d7b72..1b94a99c5 100644 --- a/arch/arm/include/asm/emif.h +++ b/arch/arm/include/asm/emif.h @@ -581,7 +581,7 @@ (0xFF << EMIF_SYS_ADDR_SHIFT)) #define EMIF_EXT_PHY_CTRL_TIMING_REG 0x5 -#define EMIF_EXT_PHY_CTRL_CONST_REG 0x13 +#define EMIF_EXT_PHY_CTRL_CONST_REG 0x14 /* Reg mapping structure */ struct emif_reg_struct { @@ -855,13 +855,10 @@ struct dmm_lisa_map_regs { #define DPD_ENABLE 1 /* Maximum delay before Low Power Modes */ -#ifndef CONFIG_OMAP54XX -#define REG_CS_TIM 0xF -#else #define REG_CS_TIM 0x0 -#endif -#define REG_SR_TIM 0xF -#define REG_PD_TIM 0xF +#define REG_SR_TIM 0x0 +#define REG_PD_TIM 0x0 + /* EMIF_PWR_MGMT_CTRL register */ #define EMIF_PWR_MGMT_CTRL (\ @@ -1113,6 +1110,7 @@ struct emif_regs { u32 freq; u32 sdram_config_init; u32 sdram_config; + u32 sdram_config2; u32 ref_ctrl; u32 sdram_tim1; u32 sdram_tim2; diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index d5daa27d1..fa2963e56 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -401,6 +401,7 @@ struct omap_sys_ctrl_regs { u32 control_ddrio_0; u32 control_ddrio_1; u32 control_ddrio_2; + u32 control_ddr_control_ext_0; u32 control_lpddr2io1_0; u32 control_lpddr2io1_1; u32 control_lpddr2io1_2; -- cgit v1.2.3-70-g09d2 From ee28edac4322602685ea12dc46edad1ec6b60487 Mon Sep 17 00:00:00 2001 From: Lubomir Popov Date: Wed, 15 May 2013 04:41:01 +0000 Subject: OMAP5: Enable access to auxclk registers auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov --- arch/arm/cpu/armv7/omap5/prcm-regs.c | 8 ++++++++ arch/arm/include/asm/arch-omap5/clock.h | 18 ++++++++++++++++++ arch/arm/include/asm/omap_common.h | 4 ++++ 3 files changed, 30 insertions(+) (limited to 'arch/arm/include/asm/omap_common.h') diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index 5a7370c77..e839ff5fe 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -308,6 +308,10 @@ struct prcm_regs const omap5_es1_prcm = { .prm_sldo_mpu_ctrl = 0x4ae07bd0, .prm_sldo_mm_setup = 0x4ae07bd4, .prm_sldo_mm_ctrl = 0x4ae07bd8, + + /* SCRM stuff, used by some boards */ + .scrm_auxclk0 = 0x4ae0a310, + .scrm_auxclk1 = 0x4ae0a314, }; struct omap_sys_ctrl_regs const omap5_ctrl = { @@ -751,6 +755,10 @@ struct prcm_regs const omap5_es2_prcm = { .prm_sldo_mm_ctrl = 0x4ae07cd8, .prm_abbldo_mpu_setup = 0x4ae07cdc, .prm_abbldo_mpu_ctrl = 0x4ae07ce0, + + /* SCRM stuff, used by some boards */ + .scrm_auxclk0 = 0x4ae0a310, + .scrm_auxclk1 = 0x4ae0a314, }; struct prcm_regs const dra7xx_prcm = { diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 1affa4f66..4d2765d87 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -281,6 +281,11 @@ #define TPS62361_BASE_VOLT_MV 500 #define TPS62361_VSEL0_GPIO 7 +/* Defines for DPLL setup */ +#define DPLL_LOCKED_FREQ_TOLERANCE_0 0 +#define DPLL_LOCKED_FREQ_TOLERANCE_500_KHZ 500 +#define DPLL_LOCKED_FREQ_TOLERANCE_1_MHZ 1000 + #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 @@ -298,4 +303,17 @@ #endif #define V_SCLK V_OSCK + +/* AUXCLKx reg fields */ +#define AUXCLK_ENABLE_MASK (1 << 8) +#define AUXCLK_SRCSELECT_SHIFT 1 +#define AUXCLK_SRCSELECT_MASK (3 << 1) +#define AUXCLK_CLKDIV_SHIFT 16 +#define AUXCLK_CLKDIV_MASK (0xF << 16) + +#define AUXCLK_SRCSELECT_SYS_CLK 0 +#define AUXCLK_SRCSELECT_CORE_DPLL 1 +#define AUXCLK_SRCSELECT_PER_DPLL 2 +#define AUXCLK_SRCSELECT_ALTERNATE 3 + #endif /* _CLOCKS_OMAP5_H_ */ diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index fa2963e56..787e614ec 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -351,6 +351,10 @@ struct prcm_regs { u32 cm_l3init_usbphy_clkctrl; u32 cm_l4per_mcbsp4_clkctrl; u32 prm_vc_cfg_channel; + + /* SCRM stuff, used by some boards */ + u32 scrm_auxclk0; + u32 scrm_auxclk1; }; struct omap_sys_ctrl_regs { -- cgit v1.2.3-70-g09d2