diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/405_mal.h | 2 | ||||
| -rw-r--r-- | include/440_i2c.h | 3 | ||||
| -rw-r--r-- | include/asm-ppc/processor.h | 4 | ||||
| -rw-r--r-- | include/asm-ppc/u-boot.h | 3 | ||||
| -rw-r--r-- | include/configs/bamboo.h | 1 | ||||
| -rw-r--r-- | include/configs/pcs440ep.h | 1 | ||||
| -rw-r--r-- | include/configs/sequoia.h | 431 | ||||
| -rw-r--r-- | include/configs/yellowstone.h | 1 | ||||
| -rw-r--r-- | include/configs/yosemite.h | 1 | ||||
| -rw-r--r-- | include/linux/mtd/compat.h | 2 | ||||
| -rw-r--r-- | include/linux/mtd/ndfc.h | 67 | ||||
| -rw-r--r-- | include/ppc440.h | 609 | ||||
| -rw-r--r-- | include/ppc4xx_enet.h | 22 | ||||
| -rw-r--r-- | include/ppc_asm.tmpl | 2 |
14 files changed, 1113 insertions, 36 deletions
diff --git a/include/405_mal.h b/include/405_mal.h index 059858695..2a421848b 100644 --- a/include/405_mal.h +++ b/include/405_mal.h @@ -92,7 +92,7 @@ #define MAL_ESR_PBEI 0x00000001 /* ^^ ^^ */ /* Mal IER */ -#ifdef CONFIG_440SPE +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define MAL_IER_PT 0x00000080 #define MAL_IER_PRE 0x00000040 #define MAL_IER_PWE 0x00000020 diff --git a/include/440_i2c.h b/include/440_i2c.h index 9c90a9e3c..0c2bf3627 100644 --- a/include/440_i2c.h +++ b/include/440_i2c.h @@ -1,7 +1,8 @@ #ifndef _440_i2c_h_ #define _440_i2c_h_ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000700) #else #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000400) diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 44b23f1eb..bbd3497c5 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -728,6 +728,10 @@ #define PVR_440EP_RC 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ #define PVR_440GR_RA 0x422218D3 /* 440EP rev B and 440GR rev A have same PVR */ #define PVR_440GR_RB 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ +#define PVR_440EPX1_RA 0x216218D0 /* 440EPX rev A with Security / Kasumi */ +#define PVR_440EPX2_RA 0x216218D4 /* 440EPX rev A without Security / Kasumi */ +#define PVR_440GRX1_RA 0x216218D8 /* 440GRX rev A with Security / Kasumi */ +#define PVR_440GRX2_RA 0x216218DC /* 440GRX rev A without Security / Kasumi */ #define PVR_440GX_RA 0x51B21850 #define PVR_440GX_RB 0x51B21851 #define PVR_440GX_RC 0x51B21892 diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h index f7aa55f33..794a6d497 100644 --- a/include/asm-ppc/u-boot.h +++ b/include/asm-ppc/u-boot.h @@ -108,7 +108,8 @@ typedef struct bd_info { #endif #if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined (CONFIG_440GX) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) unsigned int bi_opbfreq; /* OPB clock in Hz */ int bi_iic_fast[2]; /* Use fast i2c mode */ #endif diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index cd4339b58..4961011b5 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -73,6 +73,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (4 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 50c1c4fd4..23bdfc8df 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -63,6 +63,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h new file mode 100644 index 000000000..d3fcc032a --- /dev/null +++ b/include/configs/sequoia.h @@ -0,0 +1,431 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * sequoia.h - configuration for Sequoia board (PowerPC440EPx) + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_SEQUOIA 1 /* Board is Sequoia */ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ + +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CFG_OCM_BASE 0xe0010000 /* ocm */ +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 + +/* Don't change either of these */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ + +#define CFG_USB2D0_BASE 0xe0000100 +#define CFG_USB_DEVICE 0xe0000000 +#define CFG_USB_HOST 0xe0000400 +#define CFG_BCSR_BASE 0xc0000000 + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +#if 0 +/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#else +#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#endif + +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +/* + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#if 1 /* test-only */ +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#endif +#if 0 +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#endif + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE CFG_NAND_ADDR + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */ +#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#ifdef CFG_ENV_IS_IN_NAND +#define CFG_ENV_SIZE 0x4000 +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_NAND_U_BOOT_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0xa8>>1) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x0 +#endif /* CFG_ENV_IS_IN_EEPROM */ + +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_AD7414 1 /* use AD7414 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=sequoia\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/sequoia/uImage\0" \ + "kernel_addr=FE000000\0" \ + "ramdisk_addr=FE180000\0" \ + "load=tftp 100000 /tftpboot/sequoia/u-boot.bin\0" \ + "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ + "cp.b 100000 FFFA0000 60000\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_M88E1111_PHY 1 +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 1 + +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* Comment this out to enable USB 1.1 device */ +#define USB_2_0_DEVICE + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DTT | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NAND | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM | \ + CFG_CMD_USB ) + +#define CONFIG_SUPPORT_VFAT + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT +#define CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH CFG_FLASH_BASE +#define CFG_NAND 0xD0000000 +#define CFG_CPLD 0xC0000000 + +/* + * On Sequoia CS0 and CS3 are switched when configuring for NAND booting + */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 3 /* NAND chip connected to CSx */ +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03017300 +#define CFG_EBC_PB0CR (CFG_FLASH | 0xba000) + +/* Memory Bank 3 (NAND-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x018003c0 +#define CFG_EBC_PB3CR (CFG_NAND | 0x1c000) +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 3 (NOR-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x03017300 +#define CFG_EBC_PB3CR (CFG_FLASH | 0xba000) + +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND | 0x1c000) +#endif + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x24814580 +#define CFG_EBC_PB2CR (CFG_CPLD | 0x38000) + +/*----------------------------------------------------------------------- + * Cache Configuration + *----------------------------------------------------------------------*/ +#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h index cf42b666b..bcafd8ba8 100644 --- a/include/configs/yellowstone.h +++ b/include/configs/yellowstone.h @@ -65,6 +65,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 86a85b8a6..3d7b4a2f4 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -65,6 +65,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/linux/mtd/compat.h b/include/linux/mtd/compat.h index 460cd45c8..fe55087ea 100644 --- a/include/linux/mtd/compat.h +++ b/include/linux/mtd/compat.h @@ -31,11 +31,13 @@ #define max_t(type,x,y) \ ({ type __x = (x); type __y = (y); __x > __y ? __x: __y; }) +#ifndef BUG #define BUG() do { \ printf("U-Boot BUG at %s:%d!\n", __FILE__, __LINE__); \ } while (0) #define BUG_ON(condition) do { if (condition) BUG(); } while(0) +#endif /* BUG */ #define likely(x) __builtin_expect(!!(x), 1) #define unlikely(x) __builtin_expect(!!(x), 0) diff --git a/include/linux/mtd/ndfc.h b/include/linux/mtd/ndfc.h new file mode 100644 index 000000000..d0558a982 --- /dev/null +++ b/include/linux/mtd/ndfc.h @@ -0,0 +1,67 @@ +/* + * linux/include/linux/mtd/ndfc.h + * + * Copyright (c) 2006 Thomas Gleixner <tglx@linutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Info: + * Contains defines, datastructures for ndfc nand controller + * + */ +#ifndef __LINUX_MTD_NDFC_H +#define __LINUX_MTD_NDFC_H + +/* NDFC Register definitions */ +#define NDFC_CMD 0x00 +#define NDFC_ALE 0x04 +#define NDFC_DATA 0x08 +#define NDFC_ECC 0x10 +#define NDFC_BCFG0 0x30 +#define NDFC_BCFG1 0x34 +#define NDFC_BCFG2 0x38 +#define NDFC_BCFG3 0x3c +#define NDFC_CCR 0x40 +#define NDFC_STAT 0x44 +#define NDFC_HWCTL 0x48 +#define NDFC_REVID 0x50 + +#define NDFC_STAT_IS_READY 0x01000000 + +#define NDFC_CCR_RESET_CE 0x80000000 /* CE Reset */ +#define NDFC_CCR_RESET_ECC 0x40000000 /* ECC Reset */ +#define NDFC_CCR_RIE 0x20000000 /* Interrupt Enable on Device Rdy */ +#define NDFC_CCR_REN 0x10000000 /* Enable wait for Rdy in LinearR */ +#define NDFC_CCR_ROMEN 0x08000000 /* Enable ROM In LinearR */ +#define NDFC_CCR_ARE 0x04000000 /* Auto-Read Enable */ +#define NDFC_CCR_BS(x) (((x) & 0x3) << 24) /* Select Bank on CE[x] */ +#define NDFC_CCR_BS_MASK 0x03000000 /* Select Bank */ +#define NDFC_CCR_ARAC0 0x00000000 /* 3 Addr, 1 Col 2 Row 512b page */ +#define NDFC_CCR_ARAC1 0x00001000 /* 4 Addr, 1 Col 3 Row 512b page */ +#define NDFC_CCR_ARAC2 0x00002000 /* 4 Addr, 2 Col 2 Row 2K page */ +#define NDFC_CCR_ARAC3 0x00003000 /* 5 Addr, 2 Col 3 Row 2K page */ +#define NDFC_CCR_ARAC_MASK 0x00003000 /* Auto-Read mode Addr Cycles */ +#define NDFC_CCR_RPG 0x0000C000 /* Auto-Read Page */ +#define NDFC_CCR_EBCC 0x00000004 /* EBC Configuration Completed */ +#define NDFC_CCR_DHC 0x00000002 /* Direct Hardware Control Enable */ + +#define NDFC_BxCFG_EN 0x80000000 /* Bank Enable */ +#define NDFC_BxCFG_CED 0x40000000 /* nCE Style */ +#define NDFC_BxCFG_SZ_MASK 0x08000000 /* Bank Size */ +#define NDFC_BxCFG_SZ_8BIT 0x00000000 /* 8bit */ +#define NDFC_BxCFG_SZ_16BIT 0x08000000 /* 16bit */ + +#define NDFC_MAX_BANKS 4 + +struct ndfc_controller_settings { + uint32_t ccr_settings; + uint64_t ndfc_erpn; +}; + +struct ndfc_chip_settings { + uint32_t bank_settings; +}; + +#endif diff --git a/include/ppc440.h b/include/ppc440.h index d5a9f66a4..c4a3ed548 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -82,7 +82,10 @@ #define ivor13 0x19d /* interrupt vector offset register 13 */ #define ivor14 0x19e /* interrupt vector offset register 14 */ #define ivor15 0x19f /* interrupt vector offset register 15 */ -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) #define mcsrr0 0x23a /* machine check save/restore register 0 */ #define mcsrr1 0x23b /* mahcine check save/restore register 1 */ #define mcsr 0x23c /* machine check status register */ @@ -151,7 +154,18 @@ #define sdr_ecid1 0x0081 #define sdr_ecid2 0x0082 #define sdr_jtag 0x00c0 +#if !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) #define sdr_ddrdl 0x00e0 +#else +#define sdr_cfg 0x00e0 +#define SDR_CFG_LT2_MASK 0x01000000 /* Leakage test 2*/ +#define SDR_CFG_64_32BITS_MASK 0x01000000 /* Switch DDR 64 bits or 32 bits */ +#define SDR_CFG_32BITS 0x00000000 /* 32 bits */ +#define SDR_CFG_64BITS 0x01000000 /* 64 bits */ +#define SDR_CFG_MC_V2518_MASK 0x02000000 /* Low VDD2518 (2.5 or 1.8V) */ +#define SDR_CFG_MC_V25 0x00000000 /* 2.5 V */ +#define SDR_CFG_MC_V18 0x02000000 /* 1.8 V */ +#endif /* !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) */ #define sdr_ebc 0x0100 #define sdr_uart0 0x0120 /* UART0 Config */ #define sdr_uart1 0x0121 /* UART1 Config */ @@ -180,6 +194,54 @@ #define sdr_plbtr 0x4200 #define sdr_mfr 0x4300 /* SDR0_MFR reg */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* test-only!!!! */ +#define DDR0_00 0x00 +#define DDR0_01 0x01 +#define DDR0_02 0x02 +#define DDR0_03 0x03 +#define DDR0_04 0x04 +#define DDR0_05 0x05 +#define DDR0_06 0x06 +#define DDR0_07 0x07 +#define DDR0_08 0x08 +#define DDR0_09 0x09 +#define DDR0_10 0x0A +#define DDR0_11 0x0B +#define DDR0_12 0x0C +#define DDR0_13 0x0D +#define DDR0_14 0x0E +#define DDR0_15 0x0F +#define DDR0_16 0x10 +#define DDR0_17 0x11 +#define DDR0_18 0x12 +#define DDR0_19 0x13 +#define DDR0_20 0x14 +#define DDR0_21 0x15 +#define DDR0_22 0x16 +#define DDR0_23 0x17 +#define DDR0_24 0x18 +#define DDR0_25 0x19 +#define DDR0_26 0x1A +#define DDR0_27 0x1B +#define DDR0_28 0x1C +#define DDR0_29 0x1D +#define DDR0_30 0x1E +#define DDR0_31 0x1F +#define DDR0_32 0x20 +#define DDR0_33 0x21 +#define DDR0_34 0x22 +#define DDR0_35 0x23 +#define DDR0_36 0x24 +#define DDR0_37 0x25 +#define DDR0_38 0x26 +#define DDR0_39 0x27 +#define DDR0_40 0x28 +#define DDR0_41 0x29 +#define DDR0_42 0x2A +#define DDR0_43 0x2B +#define DDR0_44 0x2C +#endif /*CONFIG_440EPX*/ + /*----------------------------------------------------------------------------- | SDRAM Controller +----------------------------------------------------------------------------*/ @@ -787,7 +849,8 @@ #define xbcfg 0x23 /* external bus configuration reg */ #define xbcid 0x24 /* external bus core id reg */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* PLB4 to PLB3 Bridge OUT */ #define P4P3_DCR_BASE 0x020 @@ -877,6 +940,7 @@ #define plb1_bearl (PLB_ARBITER_BASE+ 0x0C) #define plb1_bearh (PLB_ARBITER_BASE+ 0x0D) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) /* Pin Function Control Register 1 */ #define SDR0_PFC1 0x4101 #define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ @@ -918,6 +982,178 @@ #define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ #define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ +/* Miscealleneaous Function Reg. */ +#define SDR0_MFR 0x4300 +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ +#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ + +#endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */ + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR_USB2D0CR 0x0320 +#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC Master Selection */ +#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection */ +#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */ + +#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface Selection */ +#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ +#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ + +#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */ +#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ +#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ + +/* USB2 Host Control Register */ +#define SDR0_USB2H0CR 0x0340 +#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface */ +#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */ +#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */ +#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length Adjustment */ + +/* Pin Function Control Register 1 */ +#define SDR0_PFC1 0x4101 +#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ +#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ +#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ + +#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select EMAC 0 */ +#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII bridge */ + +#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ +#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ +#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ +#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ +#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ +#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ +#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ +#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ +#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ +#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */ +#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ +#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ +#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */ +#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ +#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ +#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */ +#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ +#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ +#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */ +#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */ +#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */ + +#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */ +#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ + +/* Ethernet PLL Configuration Register */ +#define SDR0_PFC2 0x4102 +#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */ +#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication selector */ +#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */ +#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */ + +#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */ +#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */ + +/* USB2PHY0 Control Register */ +#define SDR0_USB2PHY0CR 0x4103 +#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000 /* PHY UTMI interface connection */ +#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */ +#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */ + +#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */ +#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */ +#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */ + +#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000 /* VBus detect (Device mode only) */ +#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000 /* Pull-up resistance on D+ is disabled */ +#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000 /* Pull-up resistance on D+ is enabled */ + +#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000 /* PHY UTMI data width and clock select */ +#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */ +#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */ + +#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */ +#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */ +#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000 /* Loop back enabled (only test purposes) */ + +#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000 /* Force XO block on during a suspend */ +#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */ +#define SDR0_USB2PHY0CR_XO_OFF 0x04000000 /* PHY XO block is powered-off when all ports are suspended */ + +#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only for full-speed operation */ + +#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock source */ +#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal 48M clock as a reference */ +#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO block output as a reference */ + +#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO block */ +#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external clock */ +#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock from a crystal */ + +#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */ +#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq = 12 MHz*/ +#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq = 48 MHz*/ +#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq = 24 MHz*/ + +/* Miscealleneaous Function Reg. */ +#define SDR0_MFR 0x4300 +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ + +#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */ + /* CUST0 Customer Configuration Register0 */ #define SDR0_CUST0 0x4000 #define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ @@ -1007,27 +1243,18 @@ #define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ #define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ -/* Miscealleneaous Function Reg. */ -#define SDR0_MFR 0x4300 -#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */ -#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */ -#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ -#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ -#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ -#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ -#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ -#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ -#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ -#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) -#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) - -#define SDR0_MFR_ERRATA3_EN0 0x00800000 -#define SDR0_MFR_ERRATA3_EN1 0x00400000 -#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ -#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */ -#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ -#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ -#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ +/*----------------------------------------------------------------------------- + | Internal SRAM + +----------------------------------------------------------------------------*/ +#define ISRAM0_DCR_BASE 0x380 +#define isram0_sb0cr (ISRAM0_DCR_BASE+0x00) /* SRAM bank config 0*/ +#define isram0_bear (ISRAM0_DCR_BASE+0x04) /* SRAM bus error addr reg */ +#define isram0_besr0 (ISRAM0_DCR_BASE+0x05) /* SRAM bus error status reg 0 */ +#define isram0_besr1 (ISRAM0_DCR_BASE+0x06) /* SRAM bus error status reg 1 */ +#define isram0_pmeg (ISRAM0_DCR_BASE+0x07) /* SRAM power management */ +#define isram0_cid (ISRAM0_DCR_BASE+0x08) /* SRAM bus core id reg */ +#define isram0_revid (ISRAM0_DCR_BASE+0x09) /* SRAM bus revision id reg */ +#define isram0_dpc (ISRAM0_DCR_BASE+0x0a) /* SRAM data parity check reg */ #else @@ -1121,7 +1348,7 @@ #define uic1vr (UIC1_DCR_BASE+0x7) /* UIC1 vector */ #define uic1vcr (UIC1_DCR_BASE+0x8) /* UIC1 vector configuration */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define UIC2_DCR_BASE 0xe0 #define uic2sr (UIC0_DCR_BASE+0x0) /* UIC2 status-Read Clear */ #define uic2srs (UIC0_DCR_BASE+0x1) /* UIC2 status-Read Set */ @@ -1423,6 +1650,46 @@ #define UIC_EIR6 0x00000004 /* External interrupt 6 */ #define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ #define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UIC_U0 0x80000000 /* UART 0 */ +#define UIC_U1 0x40000000 /* UART 1 */ +#define UIC_IIC0 0x20000000 /* IIC */ +#define UIC_KRD 0x10000000 /* Kasumi Ready for data */ +#define UIC_KDA 0x08000000 /* Kasumi Data Available */ +#define UIC_PCRW 0x04000000 /* PCI command register write */ +#define UIC_PPM 0x02000000 /* PCI power management */ +#define UIC_IIC1 0x01000000 /* IIC */ +#define UIC_SPI 0x00800000 /* SPI */ +#define UIC_EPCISER 0x00400000 /* External PCI SERR */ +#define UIC_MTE 0x00200000 /* MAL TXEOB */ +#define UIC_MRE 0x00100000 /* MAL RXEOB */ +#define UIC_D0 0x00080000 /* DMA channel 0 */ +#define UIC_D1 0x00040000 /* DMA channel 1 */ +#define UIC_D2 0x00020000 /* DMA channel 2 */ +#define UIC_D3 0x00010000 /* DMA channel 3 */ +#define UIC_UD0 0x00008000 /* UDMA irq 0 */ +#define UIC_UD1 0x00004000 /* UDMA irq 1 */ +#define UIC_UD2 0x00002000 /* UDMA irq 2 */ +#define UIC_UD3 0x00001000 /* UDMA irq 3 */ +#define UIC_HSB2D 0x00000800 /* USB2.0 Device */ +#define UIC_OHCI1 0x00000400 /* USB2.0 Host OHCI irq 1 */ +#define UIC_OHCI2 0x00000200 /* USB2.0 Host OHCI irq 2 */ +#define UIC_EIP94 0x00000100 /* Security EIP94 */ +#define UIC_ETH0 0x00000080 /* Emac 0 */ +#define UIC_ETH1 0x00000040 /* Emac 1 */ +#define UIC_EHCI 0x00000020 /* USB2.0 Host EHCI */ +#define UIC_EIR4 0x00000010 /* External interrupt 4 */ +#define UIC_UIC2NC 0x00000008 /* UIC2 non-critical interrupt */ +#define UIC_UIC2C 0x00000004 /* UIC2 critical interrupt */ +#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ +#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ + +/* For compatibility with 405 code */ +#define UIC_MAL_TXEOB UIC_MTE +#define UIC_MAL_RXEOB UIC_MRE + #elif !defined(CONFIG_440SPE) #define UIC_U0 0x80000000 /* UART 0 */ #define UIC_U1 0x40000000 /* UART 1 */ @@ -1531,6 +1798,48 @@ #define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ #define UIC_ETH1 0x00000002 /* Ethernet 1 */ #define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UIC_MS 0x80000000 /* MAL SERR */ +#define UIC_MTDE 0x40000000 /* MAL TXDE */ +#define UIC_MRDE 0x20000000 /* MAL RXDE */ +#define UIC_U2 0x10000000 /* UART 2 */ +#define UIC_U3 0x08000000 /* UART 3 */ +#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ +#define UIC_NDFC 0x02000000 /* NDFC */ +#define UIC_KSLE 0x01000000 /* KASUMI slave error */ +#define UIC_CT5 0x00800000 /* GPT compare timer 5 */ +#define UIC_CT6 0x00400000 /* GPT compare timer 6 */ +#define UIC_PLB34I0 0x00200000 /* PLB3X4X MIRQ0 */ +#define UIC_PLB34I1 0x00100000 /* PLB3X4X MIRQ1 */ +#define UIC_PLB34I2 0x00080000 /* PLB3X4X MIRQ2 */ +#define UIC_PLB34I3 0x00040000 /* PLB3X4X MIRQ3 */ +#define UIC_PLB34I4 0x00020000 /* PLB3X4X MIRQ4 */ +#define UIC_PLB34I5 0x00010000 /* PLB3X4X MIRQ5 */ +#define UIC_CT0 0x00008000 /* GPT compare timer 0 */ +#define UIC_CT1 0x00004000 /* GPT compare timer 1 */ +#define UIC_EIR7 0x00002000 /* External interrupt 7 */ +#define UIC_EIR8 0x00001000 /* External interrupt 8 */ +#define UIC_EIR9 0x00000800 /* External interrupt 9 */ +#define UIC_CT2 0x00000400 /* GPT compare timer 2 */ +#define UIC_CT3 0x00000200 /* GPT compare timer 3 */ +#define UIC_CT4 0x00000100 /* GPT compare timer 4 */ +#define UIC_SRE 0x00000080 /* Serial ROM error */ +#define UIC_GPTDC 0x00000040 /* GPT decrementer pulse */ +#define UIC_RSVD0 0x00000020 /* Reserved */ +#define UIC_EPCIPER 0x00000010 /* External PCI PERR */ +#define UIC_EIR0 0x00000008 /* External interrupt 0 */ +#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ +#define UIC_EIR1 0x00000002 /* External interrupt 1 */ +#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ + +/* For compatibility with 405 code */ +#define UIC_MAL_SERR UIC_MS +#define UIC_MAL_TXDE UIC_MTDE +#define UIC_MAL_RXDE UIC_MRDE +#define UIC_ENET UIC_ETH0 + #elif !defined(CONFIG_440SPE) #define UIC_MS 0x80000000 /* MAL SERR */ #define UIC_MTDE 0x40000000 /* MAL TXDE */ @@ -1608,6 +1917,20 @@ #define UIC_RSVD29 0x00000004 /* Reserved */ #define UIC_RSVD30 0x00000002 /* Reserved */ #define UIC_RSVD31 0x00000001 /* Reserved */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* UIC2 */ + +#define UIC_EIR5 0x80000000 /* External interrupt 5 */ +#define UIC_EIR6 0x40000000 /* External interrupt 6 */ +#define UIC_OPB 0x20000000 /* OPB to PLB bridge interrupt stat */ +#define UIC_EIR2 0x10000000 /* External interrupt 2 */ +#define UIC_EIR3 0x08000000 /* External interrupt 3 */ +#define UIC_DDR2 0x04000000 /* DDR2 sdram */ +#define UIC_MCTX0 0x02000000 /* MAl intp coalescence TX0 */ +#define UIC_MCTX1 0x01000000 /* MAl intp coalescence TX1 */ +#define UIC_MCTR0 0x00800000 /* MAl intp coalescence TR0 */ +#define UIC_MCTR1 0x00400000 /* MAl intp coalescence TR1 */ + #endif /* CONFIG_440GX */ /*---------------------------------------------------------------------------+ @@ -1623,6 +1946,17 @@ #define UICB0_ALL (UICB0_UIC0CI | UICB0_UIC0NCI | UICB0_UIC1CI | \ UICB0_UIC1NCI | UICB0_UIC2CI | UICB0_UIC2NCI) + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UICB0_UIC1CI 0x00000000 /* UIC1 Critical Interrupt */ +#define UICB0_UIC1NCI 0x00000000 /* UIC1 Noncritical Interrupt */ +#define UICB0_UIC2CI 0x00000000 /* UIC2 Critical Interrupt */ +#define UICB0_UIC2NCI 0x00000000 /* UIC2 Noncritical Interrupt */ + +#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | \ + UICB0_UIC1CI | UICB0_UIC2NCI) + #endif /* CONFIG_440GX */ /*---------------------------------------------------------------------------+ | Universal interrupt controller interrupts @@ -2262,7 +2596,8 @@ #define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13) #define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15) #endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 21) #define SDR0_SDSTP1_PAME_MASK (0x80000000 >> 27) #endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */ @@ -2390,11 +2725,81 @@ #define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ #define SDR0_MFR_ERRATA3_EN0 0x00800000 #define SDR0_MFR_ERRATA3_EN1 0x00400000 +#if defined(CONFIG_440GX) /* test-only: only 440GX or 440SPE??? */ #define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ #define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */ #define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ #define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ #define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ +#endif + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_PFC1_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<22) +#define SDR0_PFC1_EPS_DECODE(n) ((((unsigned long)(n))>>22)&0x07) +#define SDR0_PFC2_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<29) +#define SDR0_PFC2_EPS_DECODE(n) ((((unsigned long)(n))>>29)&0x07) +#endif + +#define SDR0_MFR_ECS_MASK 0x10000000 +#define SDR0_MFR_ECS_INTERNAL 0x10000000 + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_SRST0 0x200 +#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */ +#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */ +#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */ +#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */ +#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */ +#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */ +#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */ +#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */ +#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */ +#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */ +#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */ +#define SDR0_SRST0_PCI 0x00100000 /* PCI */ +#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */ +#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */ +#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */ +#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */ +#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */ +#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */ +#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */ +#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */ +#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */ +#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */ +#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */ +#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */ +#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */ +#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */ +#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */ +#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */ +#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */ +#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/transmitter 2 */ +#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/transmitter 3 */ + +#define SDR0_SRST1 0x201 +#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */ +#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */ +#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */ +#define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0 +#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */ +#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */ +#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4 USB 2.0 Host */ +#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to USB 2.0 Host */ +#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to USB 2.0 Host */ +#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */ +#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2 */ +#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */ +#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */ +#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */ +#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */ +#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */ +#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */ +#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */ +#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */ +#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */ + +#else #define SDR0_SRST_BGO 0x80000000 #define SDR0_SRST_PLB 0x40000000 @@ -2427,10 +2832,15 @@ #define SDR0_SRST_EMAC3 0x00000008 #define SDR0_SRST_RGMII 0x00000001 +#endif + /*-----------------------------------------------------------------------------+ | Clocking +-----------------------------------------------------------------------------*/ -#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) +#if !defined (CONFIG_440GX) && \ + !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \ + !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) #define PLLSYS0_TUNE_MASK 0xffc00000 /* PLL TUNE bits */ #define PLLSYS0_FB_DIV_MASK 0x003c0000 /* Feedback divisor */ #define PLLSYS0_FWD_DIV_A_MASK 0x00038000 /* Forward divisor A */ @@ -2498,6 +2908,120 @@ #define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */ #endif /* CONFIG_440GX */ +#if defined (CONFIG_440EPX) || defined (CONFIG_440GRX) +/*--------------------------------------*/ +#define CPR0_PLLC 0x40 +#define CPR0_PLLC_RST_MASK 0x80000000 +#define CPR0_PLLC_RST_PLLLOCKED 0x00000000 +#define CPR0_PLLC_RST_PLLRESET 0x80000000 +#define CPR0_PLLC_ENG_MASK 0x40000000 +#define CPR0_PLLC_ENG_DISABLE 0x00000000 +#define CPR0_PLLC_ENG_ENABLE 0x40000000 +#define CPR0_PLLC_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<30) +#define CPR0_PLLC_ENG_DECODE(n) ((((unsigned long)(n))>>30)&0x01) +#define CPR0_PLLC_SRC_MASK 0x20000000 +#define CPR0_PLLC_SRC_PLLOUTA 0x00000000 +#define CPR0_PLLC_SRC_PLLOUTB 0x20000000 +#define CPR0_PLLC_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<29) +#define CPR0_PLLC_SRC_DECODE(n) ((((unsigned long)(n))>>29)&0x01) +#define CPR0_PLLC_SEL_MASK 0x07000000 +#define CPR0_PLLC_SEL_PLL 0x00000000 +#define CPR0_PLLC_SEL_CPU 0x01000000 +#define CPR0_PLLC_SEL_PER 0x05000000 +#define CPR0_PLLC_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PLLC_SEL_DECODE(n) ((((unsigned long)(n))>>24)&0x07) +#define CPR0_PLLC_TUNE_MASK 0x000003FF +#define CPR0_PLLC_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) +#define CPR0_PLLC_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) +/*--------------------------------------*/ +#define CPR0_PLLD 0x60 +#define CPR0_PLLD_FBDV_MASK 0x1F000000 +#define CPR0_PLLD_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define CPR0_PLLD_FBDV_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x1F)+1) +#define CPR0_PLLD_FWDVA_MASK 0x000F0000 +#define CPR0_PLLD_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<16) +#define CPR0_PLLD_FWDVA_DECODE(n) ((((((unsigned long)(n))>>16)-1)&0x0F)+1) +#define CPR0_PLLD_FWDVB_MASK 0x00000700 +#define CPR0_PLLD_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<8) +#define CPR0_PLLD_FWDVB_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x07)+1) +#define CPR0_PLLD_LFBDV_MASK 0x0000003F +#define CPR0_PLLD_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) +#define CPR0_PLLD_LFBDV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1) +/*--------------------------------------*/ +#define CPR0_PRIMAD 0x80 +#define CPR0_PRIMAD_PRADV0_MASK 0x07000000 +#define CPR0_PRIMAD_PRADV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PRIMAD_PRADV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#define CPR0_PRIMBD 0xA0 +#define CPR0_PRIMBD_PRBDV0_MASK 0x07000000 +#define CPR0_PRIMBD_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PRIMBD_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#if 0 +#define CPR0_CPM0_ER 0xB0 /* CPM Enable Register */ +#define CPR0_CPM0_FR 0xB1 /* CPM Force Register */ +#define CPR0_CPM0_SR 0xB2 /* CPM Status Register */ +#define CPR0_CPM0_IIC0 0x80000000 /* Inter-Intergrated Circuit0 */ +#define CPR0_CPM0_IIC1 0x40000000 /* Inter-Intergrated Circuit1 */ +#define CPR0_CPM0_PCI 0x20000000 /* Peripheral Component Interconnect */ +#define CPR0_CPM0_USB1H 0x08000000 /* USB1.1 Host */ +#define CPR0_CPM0_FPU 0x04000000 /* PPC440 FPU */ +#define CPR0_CPM0_CPU 0x02000000 /* PPC440x5 Processor Core */ +#define CPR0_CPM0_DMA 0x01000000 /* Direct Memory Access Controller */ +#define CPR0_CPM0_BGO 0x00800000 /* PLB to OPB Bridge */ +#define CPR0_CPM0_BGI 0x00400000 /* OPB to PLB Bridge */ +#define CPR0_CPM0_EBC 0x00200000 /* External Bus Controller */ +#define CPR0_CPM0_NDFC 0x00100000 /* Nand Flash Controller */ +#define CPR0_CPM0_MADMAL 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ +#define CPR0_CPM0_DMC 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ +#define CPR0_CPM0_PLB4 0x00040000 /* PLB4 Arbiter */ +#define CPR0_CPM0_PLB4x3x 0x00020000 /* PLB4 to PLB3 */ +#define CPR0_CPM0_PLB3x4x 0x00010000 /* PLB3 to PLB4 */ +#define CPR0_CPM0_PLB3 0x00008000 /* PLB3 Arbiter */ +#define CPR0_CPM0_PPM 0x00002000 /* PLB Performance Monitor */ +#define CPR0_CPM0_UIC1 0x00001000 /* Universal Interrupt Controller 1 */ +#define CPR0_CPM0_GPIO 0x00000800 /* General Purpose IO */ +#define CPR0_CPM0_GPT 0x00000400 /* General Purpose Timer */ +#define CPR0_CPM0_UART0 0x00000200 /* Universal Asynchronous Rcver/Xmitter 0 */ +#define CPR0_CPM0_UART1 0x00000100 /* Universal Asynchronous Rcver/Xmitter 1 */ +#define CPR0_CPM0_UIC0 0x00000080 /* Universal Interrupt Controller 0 */ +#define CPR0_CPM0_TMRCLK 0x00000040 /* CPU Timer */ +#define CPR0_CPM0_EMC0 0x00000020 /* Ethernet 0 */ +#define CPR0_CPM0_EMC1 0x00000010 /* Ethernet 1 */ +#define CPR0_CPM0_UART2 0x00000008 /* Universal Asynchronous Rcver/Xmitter 2 */ +#define CPR0_CPM0_UART3 0x00000004 /* Universal Asynchronous Rcver/Xmitter 3 */ +#define CPR0_CPM0_USB2D 0x00000002 /* USB2.0 Device */ +#define CPR0_CPM0_USB2H 0x00000001 /* USB2.0 Host */ +#endif +/*--------------------------------------*/ +#define CPR0_OPBD 0xC0 +#define CPR0_OPBD_OPBDV0_MASK 0x03000000 +#define CPR0_OPBD_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_OPBD_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_PERD 0xE0 +#define CPR0_PERD_PERDV0_MASK 0x07000000 +#define CPR0_PERD_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PERD_PERDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#define CPR0_MALD 0x100 +#define CPR0_MALD_MALDV0_MASK 0x03000000 +#define CPR0_MALD_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_MALD_MALDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_SPCID 0x120 +#define CPR0_SPCID_SPCIDV0_MASK 0x03000000 +#define CPR0_SPCID_SPCIDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_SPCID_SPCIDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_ICFG 0x140 +#define CPR0_ICFG_RLI_MASK 0x80000000 +#define CPR0_ICFG_RLI_RESETCPR 0x00000000 +#define CPR0_ICFG_RLI_PRESERVECPR 0x80000000 +#define CPR0_ICFG_ICS_MASK 0x00000007 +#endif /* defined (CONFIG_440EPX) || defined (CONFIG_440GRX) */ + /*----------------------------------------------------------------------------- | IIC Register Offsets '----------------------------------------------------------------------------*/ @@ -2539,7 +3063,8 @@ #define PCIX0_CFGBASE (CFG_PCI_BASE + 0x0ec80000) #define PCIX0_IOBASE (CFG_PCI_BASE + 0x08000000) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* PCI Local Configuration Registers --------------------------------- */ @@ -2625,6 +3150,33 @@ #endif /* !defined(CONFIG_440EP) !defined(CONFIG_440GR) */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +/* USB2.0 Device */ +#define USB2D0_BASE CFG_USB2D0_BASE + +#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) + +#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for Endpoint 0 plus IN Endpoints 1 to 3 */ +#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management register */ +#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address register */ +#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRIN */ +#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for OUT Endpoints 1 to 3 */ +#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRUSB */ +#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for common USB interrupts */ +#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for IntrOut */ +#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0 test modes */ +#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for selecting the Endpoint status/control registers */ +#define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */ +#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status register for Endpoint 0. (Index register set to select Endpoint 0) */ +#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status register for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status register for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */ +#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in OUT Endpoint FIFO. (Index register set to select Endpoints 13) */ +#endif + /****************************************************************************** * GPIO macro register defines ******************************************************************************/ @@ -2640,7 +3192,8 @@ #define GPIO0_IR (GPIO0_BASE+0x1C) #endif /* CONFIG_440GP */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000B00) #define GPIO1_BASE (CFG_PERIPHERAL_BASE+0x00000C00) diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index ec2e3629b..43c5ca451 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -145,12 +145,14 @@ typedef struct emac_4xx_hw_st { #define EMAC_STACR_OC_MASK (0x00000000) #endif -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_PFC1_EM_1000 (0x00200000) #endif /*ZMII Bridge Register addresses */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define ZMII_BASE (CFG_PERIPHERAL_BASE + 0x0D00) #else #define ZMII_BASE (CFG_PERIPHERAL_BASE + 0x0780) @@ -163,6 +165,7 @@ typedef struct emac_4xx_hw_st { #define ZMII_MDI0 0x80000000 /* ZMII FER Register Bit Definitions */ +#define ZMII_FER_DIS (0x0) #define ZMII_FER_MDI (0x8) #define ZMII_FER_SMII (0x4) #define ZMII_FER_RMII (0x2) @@ -197,7 +200,11 @@ typedef struct emac_4xx_hw_st { #define ZMII_SMIISR_V(__x) ((3 - __x) * 8) /* RGMII Register Addresses */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x1000) +#else #define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x0790) +#endif #define RGMII_FER (RGMII_BASE + 0x00) #define RGMII_SSR (RGMII_BASE + 0x04) @@ -216,7 +223,11 @@ typedef struct emac_4xx_hw_st { #define RGMII_SSR_SP_100MBPS (0x02) #define RGMII_SSR_SP_1000MBPS (0x04) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define RGMII_SSR_V(__x) ((__x) * 8) +#else #define RGMII_SSR_V(__x) ((__x -2) * 8) +#endif /*---------------------------------------------------------------------------+ @@ -286,7 +297,8 @@ typedef struct emac_4xx_hw_st { /* Ethernet MAC Regsiter Addresses */ #if defined(CONFIG_440) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define EMAC_BASE (CFG_PERIPHERAL_BASE + 0x0E00) #else #define EMAC_BASE (CFG_PERIPHERAL_BASE + 0x0800) @@ -332,7 +344,9 @@ typedef struct emac_4xx_hw_st { #define EMAC_M0_WKE (0x04000000) /* on 440GX EMAC_MR1 has a different layout! */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* MODE Reg 1 */ #define EMAC_M1_FDE (0x80000000) #define EMAC_M1_ILE (0x40000000) diff --git a/include/ppc_asm.tmpl b/include/ppc_asm.tmpl index 72d690ef0..3e47e82ab 100644 --- a/include/ppc_asm.tmpl +++ b/include/ppc_asm.tmpl @@ -312,7 +312,7 @@ label: \ lwz r3,GOT(transfer_to_handler); \ mtlr r3; \ addi r3,r1,STACK_FRAME_OVERHEAD; \ - li r20,MSR_KERNEL; \ + li r20,(MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)); \ rlwimi r20,r23,0,25,25; \ blrl ; \ .L_ ## label : \ |