diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/ACEX1K.h | 19 | ||||
| -rw-r--r-- | include/altera.h | 4 | ||||
| -rw-r--r-- | include/common.h | 2 | ||||
| -rw-r--r-- | include/configs/TQM5200.h | 46 | ||||
| -rw-r--r-- | include/configs/alpr.h | 346 | ||||
| -rw-r--r-- | include/configs/sequoia.h | 13 | ||||
| -rw-r--r-- | include/configs/v38b.h | 4 | ||||
| -rw-r--r-- | include/configs/yellowstone.h | 1 | ||||
| -rw-r--r-- | include/configs/yosemite.h | 1 | ||||
| -rw-r--r-- | include/environment.h | 3 | ||||
| -rw-r--r-- | include/flash.h | 8 | ||||
| -rw-r--r-- | include/ppc440.h | 2 |
12 files changed, 401 insertions, 48 deletions
diff --git a/include/ACEX1K.h b/include/ACEX1K.h index f75c463f3..f249d6402 100644 --- a/include/ACEX1K.h +++ b/include/ACEX1K.h @@ -35,6 +35,11 @@ extern int ACEX1K_dump( Altera_desc *desc, void *buf, size_t bsize ); extern int ACEX1K_info( Altera_desc *desc ); extern int ACEX1K_reloc( Altera_desc *desc, ulong reloc_off ); +extern int CYC2_load( Altera_desc *desc, void *image, size_t size ); +extern int CYC2_dump( Altera_desc *desc, void *buf, size_t bsize ); +extern int CYC2_info( Altera_desc *desc ); +extern int CYC2_reloc( Altera_desc *desc, ulong reloc_off ); + /* Slave Serial Implementation function table */ typedef struct { Altera_pre_fn pre; @@ -48,6 +53,18 @@ typedef struct { int relocated; } Altera_ACEX1K_Passive_Serial_fns; +/* Slave Serial Implementation function table */ +typedef struct { + Altera_pre_fn pre; + Altera_config_fn config; + Altera_status_fn status; + Altera_done_fn done; + Altera_write_fn write; + Altera_abort_fn abort; + Altera_post_fn post; + int relocated; +} Altera_CYC2_Passive_Serial_fns; + /* Device Image Sizes *********************************************************************/ /* ACEX1K */ @@ -60,6 +77,8 @@ typedef struct { #endif #define Altera_EP1K100_SIZE (166965*8) +#define Altera_EP2C35_SIZE 883905 + /* Descriptor Macros *********************************************************************/ /* ACEX1K devices */ diff --git a/include/altera.h b/include/altera.h index 74b6729f9..7b8cb4a55 100644 --- a/include/altera.h +++ b/include/altera.h @@ -34,8 +34,10 @@ /* Altera Model definitions *********************************************************************/ #define CFG_ACEX1K CFG_FPGA_DEV( 0x1 ) +#define CFG_CYCLON2 CFG_FPGA_DEV( 0x2 ) #define CFG_ALTERA_ACEX1K (CFG_FPGA_ALTERA | CFG_ACEX1K) +#define CFG_ALTERA_CYCLON2 (CFG_FPGA_ALTERA | CFG_CYCLON2) /* Add new models here */ /* Altera Interface definitions @@ -56,6 +58,7 @@ typedef enum { /* typedef Altera_iface */ typedef enum { /* typedef Altera_Family */ min_altera_type, /* insert all new types after this */ Altera_ACEX1K, /* ACEX1K Family */ + Altera_CYC2, /* CYCLONII Family */ /* Add new models here */ max_altera_type /* insert all new types before this */ } Altera_Family; /* end, typedef Altera_Family */ @@ -84,6 +87,7 @@ typedef int (*Altera_status_fn)( int cookie ); typedef int (*Altera_done_fn)( int cookie ); typedef int (*Altera_clk_fn)( int assert_clk, int flush, int cookie ); typedef int (*Altera_data_fn)( int assert_data, int flush, int cookie ); +typedef int (*Altera_write_fn)(void *buf, size_t len, int flush, int cookie); typedef int (*Altera_abort_fn)( int cookie ); typedef int (*Altera_post_fn)( int cookie ); diff --git a/include/common.h b/include/common.h index 349d5cf72..ac78d1c00 100644 --- a/include/common.h +++ b/include/common.h @@ -270,7 +270,7 @@ int misc_init_r (void); void jumptable_init(void); /* common/memsize.c */ -int get_ram_size (volatile long *, long); +long get_ram_size (volatile long *, long); /* $(BOARD)/$(BOARD).c */ void reset_phy (void); diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 4bae103e0..08674ca49 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -217,43 +217,19 @@ #undef CONFIG_BOOTARGS -#ifdef CONFIG_STK52XX -# if defined(CONFIG_TQM5200_B) -# if defined(CFG_LOWBOOT) -# define ENV_UPDT \ - "update=protect off FC000000 FC07FFFF;" \ - "erase FC000000 FC07FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC07FFFF\0" -# else /* highboot */ -# define ENV_UPDT \ - "update=protect off FFF00000 FFF7FFFF;" \ - "erase FFF00000 FFF7FFFF;" \ +#if defined(CONFIG_TQM5200_B) && !defined(CFG_LOWBOOT) +# define ENV_UPDT \ + "update=protect off FFF00000 +${filesize};" \ + "erase FFF00000 +${filesize};" \ "cp.b 200000 FFF00000 ${filesize};" \ - "protect on FFF00000 FFF7FFFF\0" -# endif /* CFG_LOWBOOT */ -# else /* !CONFIG_TQM5200_B */ -# define ENV_UPDT \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" -# endif /* CONFIG_TQM5200_B */ -#elif defined (CONFIG_CAM5200) -# define ENV_UPDT \ - "update=protect off FC000000 FC03FFFF;" \ - "erase FC000000 FC03FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC03FFFF\0" -#elif defined (CONFIG_FO300) + "protect on FFF00000 +${filesize}\0" +#else /* default lowboot configuration */ # define ENV_UPDT \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ + "update=protect off FC000000 +${filesize};" \ + "erase FC000000 +${filesize};" \ "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" -#else -# error "Unknown Carrier Board" -#endif /* CONFIG_STK52XX */ + "protect on FC000000 +${filesize}\0" +#endif #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ @@ -432,7 +408,7 @@ */ #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 0x4000 /* 16 k - keep small for fast booting */ -#if defined(CONFIG_TQM5200_B) +#if defined(CONFIG_TQM5200_B) || defined (CONFIG_CAM5200) #define CFG_ENV_SECT_SIZE 0x40000 #else #define CFG_ENV_SECT_SIZE 0x20000 diff --git a/include/configs/alpr.h b/include/configs/alpr.h new file mode 100644 index 000000000..bbe6b76bf --- /dev/null +++ b/include/configs/alpr.h @@ -0,0 +1,346 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_ALPR 1 /* Board is ebony */ +#define CONFIG_440GX 1 /* Specifc GX support */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ +#undef CFG_DRAM_TEST /* Disable-takes long time! */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ +#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ +#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 + + +#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) +#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CFG_TEMP_STACK_OCM 1 +#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE +#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ + +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK +#define CONFIG_BAUDRATE 115200 +#define CONFIG_UART1_CONSOLE /* define for uart1 as console */ + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI 1 /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ +#undef CONFIG_SDRAM_ECC /* enable ECC support */ +#define CFG_SDRAM_TABLE { \ + {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ + {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (PCF8594C) + *----------------------------------------------------------------------*/ +#define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ + /* 8 byte page write mode using */ + /* last 3 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth3\0" \ + "hostname=alpr\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ + "mem=193M\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/projects/alpr/nfs_root\0" \ + "bootfile=/alpr/uImage\0" \ + "kernel_addr=fff00000\0" \ + "ramdisk_addr=fff10000\0" \ + "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b 100000 fffc0000 40000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ +#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ +#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ +#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#define CONFIG_HAS_ETH3 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_FPGA | \ + CFG_CMD_NAND | \ + CFG_CMD_REGINFO) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT /* let board init pci target */ +#define CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ + +/*----------------------------------------------------------------------- + * FPGA stuff + *-----------------------------------------------------------------------*/ +#define CONFIG_FPGA CFG_ALTERA_CYCLON2 +#define CFG_FPGA_CHECK_CTRLC +#define CFG_FPGA_PROG_FEEDBACK +#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in + Reihe geschaltet -> sollte gehen, + aufpassen mit Datasize ist jetzt + halt doppelt so gross ... Seite 306 + ist das mit den multiple Device in PS + Mode erklaert ...*/ + +/* FPGA program pin configuration */ +#define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ +#define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */ +#define CFG_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ +#define CFG_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ +#define CFG_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ + +#define CFG_GPIO_SEL_DPR 14 /* cpu output */ +#define CFG_GPIO_SEL_AVR 15 /* cpu output */ +#define CFG_GPIO_PROG_EN 23 /* cpu output */ + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup + *-----------------------------------------------------------------------*/ +#define CFG_GPIO_EREADY (0x80000000 >> 26) +#define CFG_GPIO_REV0 (0x80000000 >> 14) +#define CFG_GPIO_REV1 (0x80000000 >> 15) + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *-----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 4 +#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE +#define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \ + CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 } +#define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH CFG_FLASH_BASE + +/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x92015480 +#define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (NAND-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ +#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 3a76315b4..00b92220c 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -53,7 +53,7 @@ #define CFG_BOOT_BASE_ADDR 0xf0000000 #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CFG_MONITOR_BASE TEXT_BASE #define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ #define CFG_OCM_BASE 0xe0010000 /* ocm */ @@ -102,6 +102,7 @@ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #else #define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /*----------------------------------------------------------------------- @@ -234,10 +235,10 @@ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ + "rootpath=/opt/eldk/ppc_4xxFP\0" \ "bootfile=/tftpboot/sequoia/uImage\0" \ - "kernel_addr=FE000000\0" \ - "ramdisk_addr=FE180000\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ "load=tftp 100000 /tftpboot/sequoia/u-boot.bin\0" \ "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ "cp.b 100000 FFFA0000 60000\0" \ @@ -378,7 +379,7 @@ #define CFG_NAND_CS 3 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x03017300 -#define CFG_EBC_PB0CR (CFG_FLASH | 0xba000) +#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000) /* Memory Bank 3 (NAND-FLASH) initialization */ #define CFG_EBC_PB3AP 0x018003c0 @@ -387,7 +388,7 @@ #define CFG_NAND_CS 0 /* NAND chip connected to CSx */ /* Memory Bank 3 (NOR-FLASH) initialization */ #define CFG_EBC_PB3AP 0x03017300 -#define CFG_EBC_PB3CR (CFG_FLASH | 0xba000) +#define CFG_EBC_PB3CR (CFG_FLASH | 0xda000) /* Memory Bank 0 (NAND-FLASH) initialization */ #define CFG_EBC_PB0AP 0x018003c0 diff --git a/include/configs/v38b.h b/include/configs/v38b.h index cf2d031c9..554a7a41b 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -34,7 +34,7 @@ #define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ #define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ -#define CONFIG_HW_WATCHDOG 1 /* has watchdog */ +#undef CONFIG_HW_WATCHDOG /* don't use watchdog */ #define CONFIG_NETCONSOLE 1 @@ -246,7 +246,7 @@ /* * GPIO configuration */ -#define CFG_GPS_PORT_CONFIG 0x90000404 +#define CFG_GPS_PORT_CONFIG 0x90001404 /* * Miscellaneous configurable options diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h index ba27f37f6..58717f8a6 100644 --- a/include/configs/yellowstone.h +++ b/include/configs/yellowstone.h @@ -37,6 +37,7 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_BOARD_RESET 1 /* call board_reset() */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 3d7b4a2f4..6e942abca 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -37,6 +37,7 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_BOARD_RESET 1 /* call board_reset() */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the diff --git a/include/environment.h b/include/environment.h index 26b07120d..af605ab7a 100644 --- a/include/environment.h +++ b/include/environment.h @@ -79,8 +79,7 @@ # ifdef CFG_ENV_OFFSET_REDUND # define CFG_REDUNDAND_ENVIRONMENT # endif -# if defined(CONFIG_NAND_U_BOOT) -/* Use embedded environment in NAND boot versions */ +# ifdef CFG_ENV_IS_EMBEDDED # define ENV_IS_EMBEDDED 1 # endif #endif /* CFG_ENV_IS_IN_NAND */ diff --git a/include/flash.h b/include/flash.h index d91589a6c..9c57cbc42 100644 --- a/include/flash.h +++ b/include/flash.h @@ -43,9 +43,14 @@ typedef struct { ulong write_tout; /* maximum write timeout */ ulong buffer_write_tout; /* maximum buffer write timeout */ ushort vendor; /* the primary vendor id */ - ushort cmd_reset; /* Vendor specific reset command */ + ushort cmd_reset; /* vendor specific reset command */ ushort interface; /* used for x8/x16 adjustments */ ushort legacy_unlock; /* support Intel legacy (un)locking */ + uchar manufacturer_id; /* manufacturer id */ + ushort device_id; /* device id */ + ushort device_id2; /* extended device id */ + ushort ext_addr; /* extended query table address */ + ushort cfi_version; /* cfi version */ #endif } flash_info_t; @@ -439,6 +444,7 @@ extern void flash_read_factory_serial(flash_info_t * info, void * buffer, int of #define FLASH_MAN_MT 0x00400000 #define FLASH_MAN_SHARP 0x00500000 #define FLASH_MAN_ATM 0x00600000 +#define FLASH_MAN_CFI 0x01000000 #define FLASH_TYPEMASK 0x0000FFFF /* extract FLASH type information */ diff --git a/include/ppc440.h b/include/ppc440.h index e407320a9..407daaebe 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -3183,7 +3183,7 @@ #define GPIO0 0 #define GPIO1 1 -#if defined(CONFIG_440GP) +#if defined(CONFIG_440GP) || defined(CONFIG_440GX) #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000700) #define GPIO0_OR (GPIO0_BASE+0x0) |