diff options
Diffstat (limited to 'include/configs/v38b.h')
| -rw-r--r-- | include/configs/v38b.h | 154 |
1 files changed, 77 insertions, 77 deletions
diff --git a/include/configs/v38b.h b/include/configs/v38b.h index 35745484d..0156ce1c1 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -29,7 +29,7 @@ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ #define CONFIG_V38B 1 /* ...on V38B board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ...running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ...running at 33.000000MHz */ #define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ #define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ @@ -41,7 +41,7 @@ #define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */ -#define CFG_XLB_PIPELINING 1 /* gives better performance */ +#define CONFIG_SYS_XLB_PIPELINING 1 /* gives better performance */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ @@ -53,7 +53,7 @@ */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* * DDR @@ -121,8 +121,8 @@ /* * Boot low with 16 MB Flash */ -#define CFG_LOWBOOT 1 -#define CFG_LOWBOOT16 1 +#define CONFIG_SYS_LOWBOOT 1 +#define CONFIG_SYS_LOWBOOT16 1 /* * Autobooting @@ -173,75 +173,75 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 /* * RTC configuration */ -#define CFG_I2C_RTC_ADDR 0x51 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* * Flash configuration - use CFI driver */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_CFI_AMD_RESET 1 -#define CFG_FLASH_BASE 0xFF000000 -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } -#define CFG_FLASH_SIZE 0x01000000 /* 16 MiB */ -#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ +#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 +#define CONFIG_SYS_FLASH_BASE 0xFF000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MiB */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ /* * Environment settings */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000) -#define CFG_ENV_SIZE 0x10000 -#define CFG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000) +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_OVERWRITE 1 /* * Memory map */ -#define CFG_MBAR 0xF0000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 /* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Linux initial memory map */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */ /* * Ethernet configuration @@ -253,50 +253,50 @@ /* * GPIO configuration */ -#define CFG_GPS_PORT_CONFIG 0x90001404 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x90001404 /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Various low-level settings */ -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00047801 -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00047801 +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 -#define CFG_RESET_ADDRESS 0xff000000 +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 /* * IDE/ATA (supports IDE harddisk) @@ -308,20 +308,20 @@ #define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -#define CFG_ATA_DATA_OFFSET (0x0060) /* data I/O offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* data I/O offset */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) /* normal register accesses offset */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* normal register accesses offset */ -#define CFG_ATA_ALT_OFFSET (0x005C) /* alternate registers offset */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* alternate registers offset */ -#define CFG_ATA_STRIDE 4 /* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ /* * Status LED @@ -329,26 +329,26 @@ #define CONFIG_STATUS_LED /* Status LED enabled */ #define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ -#define CFG_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */ +#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */ #ifndef __ASSEMBLY__ typedef unsigned int led_id_t; #define __led_toggle(_msk) \ do { \ - *((volatile long *) (CFG_LED_BASE)) ^= (_msk); \ + *((volatile long *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \ } while(0) #define __led_set(_msk, _st) \ do { \ if ((_st)) \ - *((volatile long *) (CFG_LED_BASE)) &= ~(_msk); \ + *((volatile long *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \ else \ - *((volatile long *) (CFG_LED_BASE)) |= (_msk); \ + *((volatile long *) (CONFIG_SYS_LED_BASE)) |= (_msk); \ } while(0) #define __led_init(_msk, st) \ do { \ - *((volatile long *) (CFG_LED_BASE)) |= 0x34; \ + *((volatile long *) (CONFIG_SYS_LED_BASE)) |= 0x34; \ } while(0) #endif /* __ASSEMBLY__ */ |