diff options
Diffstat (limited to 'include/configs/cobra5272.h')
| -rw-r--r-- | include/configs/cobra5272.h | 148 |
1 files changed, 74 insertions, 74 deletions
diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index ee5116e09..fb32f3f3c 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -53,13 +53,13 @@ /* --- * Defines processor clock - important for correct timings concerning serial * interface etc. - * CFG_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms + * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms * --- */ -#define CFG_HZ 1000 -#define CFG_CLK 66000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 66000000 +#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ /* --- * Enable use of Ethernet @@ -73,15 +73,15 @@ /* --- * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CFG_BAUDRATE_TABLE defines values that can be selected in u-boot command + * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command * interface * --- */ #define CONFIG_MCFUART -#define CFG_UART_PORT (0) +#define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 19200 -#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } /* --- * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change @@ -159,22 +159,22 @@ # define CONFIG_NET_MULTI 1 # define CONFIG_MII 1 # define CONFIG_MII_INIT 1 -# define CFG_DISCOVER_PHY -# define CFG_RX_ETH_BUFFER 8 -# define CFG_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_DISCOVER_PHY +# define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CFG_FEC0_PINMUX 0 -# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define CONFIG_SYS_FEC0_PINMUX 0 +# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE # define MCFFEC_TOUT_LOOP 50000 -/* If CFG_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CFG_DISCOVER_PHY +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CONFIG_SYS_DISCOVER_PHY # define FECDUPLEX FULL # define FECSPEED _100BASET # else -# ifndef CFG_FAULT_ECHO_LINK_DOWN -# define CFG_FAULT_ECHO_LINK_DOWN +# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # endif -# endif /* CFG_DISCOVER_PHY */ +# endif /* CONFIG_SYS_DISCOVER_PHY */ #endif /* @@ -211,23 +211,23 @@ considered during boot */ #endif -#define CFG_PROMPT "COBRA > " /* Layout of u-boot prompt*/ +#define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/ -#define CFG_LOAD_ADDR 0x20000 /*Defines default RAM address +#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address from which user programs will be started */ /*---*/ -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ /* *----------------------------------------------------------------------------- @@ -240,8 +240,8 @@ from which user programs will be started */ * --- */ -#define CFG_MEMTEST_START 0x400 -#define CFG_MEMTEST_END 0x380000 +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 /* --- * Low Level Configuration Settings @@ -255,39 +255,39 @@ from which user programs will be started */ * --- */ -#define CFG_MBAR 0x10000000 /* Register Base Addrs */ +#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ /* --- * System Conf. Reg. & System Protection Reg. * --- */ -#define CFG_SCR 0x0003 -#define CFG_SPR 0xffff +#define CONFIG_SYS_SCR 0x0003 +#define CONFIG_SYS_SPR 0xffff /* --- * Ethernet settings * --- */ -#define CFG_DISCOVER_PHY -#define CFG_ENET_BD_BASE 0x780000 +#define CONFIG_SYS_DISCOVER_PHY +#define CONFIG_SYS_ENET_BD_BASE 0x780000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in internal SRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* *------------------------------------------------------------------------- @@ -295,42 +295,42 @@ from which user programs will be started */ *----------------------------------------------------------------------- */ -/* #define CFG_SDRAM_SIZE 16 */ +/* #define CONFIG_SYS_SDRAM_SIZE 16 */ /* *----------------------------------------------------------------------- */ -#define CFG_FLASH_BASE 0xffe00000 +#define CONFIG_SYS_FLASH_BASE 0xffe00000 #ifdef CONFIG_MONITOR_IS_IN_RAM -#define CFG_MONITOR_BASE 0x20000 +#define CONFIG_SYS_MONITOR_BASE 0x20000 #else -#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #endif -#define CFG_MONITOR_LEN 0x20000 -#define CFG_MALLOC_LEN (256 << 10) -#define CFG_BOOTPARAMS_LEN 64*1024 +#define CONFIG_SYS_MONITOR_LEN 0x20000 +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 1000 /* flash timeout */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 +#define CONFIG_SYS_CACHELINE_SIZE 16 /*----------------------------------------------------------------------- * Memory bank definitions @@ -338,29 +338,29 @@ from which user programs will be started */ * Please refer also to Motorola Coldfire user manual - Chapter XXX * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf> */ -#define CFG_BR0_PRELIM 0xFFE00201 -#define CFG_OR0_PRELIM 0xFFE00014 +#define CONFIG_SYS_BR0_PRELIM 0xFFE00201 +#define CONFIG_SYS_OR0_PRELIM 0xFFE00014 -#define CFG_BR1_PRELIM 0 -#define CFG_OR1_PRELIM 0 +#define CONFIG_SYS_BR1_PRELIM 0 +#define CONFIG_SYS_OR1_PRELIM 0 -#define CFG_BR2_PRELIM 0 -#define CFG_OR2_PRELIM 0 +#define CONFIG_SYS_BR2_PRELIM 0 +#define CONFIG_SYS_OR2_PRELIM 0 -#define CFG_BR3_PRELIM 0 -#define CFG_OR3_PRELIM 0 +#define CONFIG_SYS_BR3_PRELIM 0 +#define CONFIG_SYS_OR3_PRELIM 0 -#define CFG_BR4_PRELIM 0 -#define CFG_OR4_PRELIM 0 +#define CONFIG_SYS_BR4_PRELIM 0 +#define CONFIG_SYS_OR4_PRELIM 0 -#define CFG_BR5_PRELIM 0 -#define CFG_OR5_PRELIM 0 +#define CONFIG_SYS_BR5_PRELIM 0 +#define CONFIG_SYS_OR5_PRELIM 0 -#define CFG_BR6_PRELIM 0 -#define CFG_OR6_PRELIM 0 +#define CONFIG_SYS_BR6_PRELIM 0 +#define CONFIG_SYS_OR6_PRELIM 0 -#define CFG_BR7_PRELIM 0x00000701 -#define CFG_OR7_PRELIM 0xFF00007C +#define CONFIG_SYS_BR7_PRELIM 0x00000701 +#define CONFIG_SYS_OR7_PRELIM 0xFF00007C /*----------------------------------------------------------------------- * LED config @@ -377,15 +377,15 @@ from which user programs will be started */ /*----------------------------------------------------------------------- * Port configuration (GPIO) */ -#define CFG_PACNT 0x00000000 /* PortA control reg.: All pins are external +#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external GPIO*/ -#define CFG_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs +#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs (1^=output, 0^=input) */ -#define CFG_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ -#define CFG_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART +#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ +#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART configuration */ -#define CFG_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ -#define CFG_PBDAT 0x0000 /* PortB value reg. */ -#define CFG_PDCNT 0x00000000 /* PortD control reg. */ +#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ +#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ +#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ #endif /* _CONFIG_COBRA5272_H */ |