diff options
Diffstat (limited to 'include/configs/bamboo.h')
| -rw-r--r-- | include/configs/bamboo.h | 401 |
1 files changed, 401 insertions, 0 deletions
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h new file mode 100644 index 000000000..64ea6bef9 --- /dev/null +++ b/include/configs/bamboo.h @@ -0,0 +1,401 @@ +/* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * bamboo.h - configuration for BAMBOO board + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_BAMBOO 1 /* Board is BAMBOO */ +#define CONFIG_440EP 1 /* Specific PPC440EP support */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ + +/* + * Please note that, if NAND support is enabled, the 2nd ethernet port + * can't be used because of pin multiplexing. So, if you want to use the + * 2nd ethernet port you have to "undef" the following define. + */ +#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ +#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 + +/*Don't change either of these*/ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ +#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/ +/*Don't change either of these*/ + +#define CFG_USB_DEVICE 0x50000000 +#define CFG_NVRAM_BASE_ADDR 0x80000000 +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_NAND_ADDR 0x90000000 +#define CFG_NAND2_ADDR 0x94000000 + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in SDRAM) + *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_END (8 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * NVRAM/RTC + * + * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF + * The DS1558 code assumes this condition + * + *----------------------------------------------------------------------*/ +#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ +#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +/* + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#if 1 +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#endif + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_ADDR0 0x555 +#define CFG_FLASH_ADDR1 0x2aa +#define CFG_FLASH_WORD_SIZE unsigned char + +#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ + +/*----------------------------------------------------------------------- + * NAND-FLASH related + *----------------------------------------------------------------------*/ +#define NAND_CMD_REG (0x00) /* NandFlash Command Register */ +#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */ +#define NAND_DATA_REG (0x08) /* NandFlash Data Register */ +#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */ +#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */ +#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */ +#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */ +#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */ +#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */ +#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */ +#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */ +#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */ +#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */ +#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */ +#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */ +#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */ +#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */ +#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */ +#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */ + +/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */ +#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */ +#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */ +#define NAND0_CMD_READ2 0x50 +#define NAND0_CMD_READ_ID 0x90 +#define NAND0_CMD_READ_STATUS 0x70 +#define NAND0_CMD_RESET 0xFF +#define NAND0_CMD_PAGE_PROG 0x80 +#define NAND0_CMD_PAGE_PROG_TRUE 0x10 +#define NAND0_CMD_PAGE_PROG_DUMMY 0x11 +#define NAND0_CMD_BLOCK_ERASE 0x60 +#define NAND0_CMD_BLOCK_ERASE_END 0xD0 + +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define SECTORSIZE 512 + +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 + +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0) +#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0) +#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0) +#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG)) +#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01)) + +/* not needed with 440EP NAND controller */ +#define NAND_CTL_CLRALE(nandptr) +#define NAND_CTL_SETALE(nandptr) +#define NAND_CTL_CLRCLE(nandptr) +#define NAND_CTL_SETCLE(nandptr) +#define NAND_DISABLE_CE(nand) +#define NAND_ENABLE_CE(nand) + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------------- */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ +#define SPD_EEPROM_ADDRESS {0x50,0x51} /* SPD i2c spd addresses */ +#define CFG_SDRAM_ONBOARD_SIZE (64 << 20) /* Bamboo has onboard and DIMM-slots!*/ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0xa8>>1) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x0 +#endif /* CFG_ENV_IS_IN_EEPROM */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=bamboo\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/bamboo/uImage\0" \ + "kernel_addr=fff00000\0" \ + "ramdisk_addr=fff10000\0" \ + "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ + "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ + "cp.b 100000 fff80000 80000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#ifndef CONFIG_BAMBOO_NAND +#define CONFIG_NET_MULTI 1 /* required for netconsole */ +#define CONFIG_PHY1_ADDR 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#endif /* CONFIG_BAMBOO_NAND */ + +#define CONFIG_NO_PHY_RESET 1 /* no PHY reset on bamboo!!! */ + +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +#ifdef CONFIG_440EP +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/*Comment this out to enable USB 1.1 device*/ +#define USB_2_0_DEVICE +#endif /*CONFIG_440EP*/ + +#ifdef CONFIG_BAMBOO_NAND +#define _CFG_CMD_NAND CFG_CMD_NAND +#else +#define _CFG_CMD_NAND 0 +#endif /* CONFIG_BAMBOO_NAND */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM | \ + CFG_CMD_USB | \ + _CFG_CMD_NAND | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_LYNXKDI 1 /* support kdi files */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT +#define CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE (32<<10) /* For IBM 440 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ |