diff options
Diffstat (limited to 'include/configs/Total5200.h')
| -rw-r--r-- | include/configs/Total5200.h | 194 |
1 files changed, 97 insertions, 97 deletions
diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h index 19b3be7db..75d1985ff 100644 --- a/include/configs/Total5200.h +++ b/include/configs/Total5200.h @@ -43,7 +43,7 @@ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ @@ -55,7 +55,7 @@ */ #define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* * Video console @@ -95,7 +95,7 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 #define CONFIG_EEPRO100 1 -#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 #else /* MGT5100 */ @@ -141,7 +141,7 @@ #if (TEXT_BASE == 0xFE000000) /* Boot low */ -# define CFG_LOWBOOT 1 +# define CONFIG_SYS_LOWBOOT 1 #endif /* @@ -180,54 +180,54 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 /* * Flash configuration */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #if CONFIG_TOTAL5200_REV==2 -# define CFG_MAX_FLASH_BANKS 3 /* max num of flash banks */ -# define CFG_FLASH_BANKS_LIST { CFG_CS5_START, CFG_CS4_START, CFG_BOOTCS_START } +# define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */ +# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START } #else -# define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ -# define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ +# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } #endif -#define CFG_FLASH_EMPTY_INFO -#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ #if CONFIG_TOTAL5200_REV==1 -# define CFG_FLASH_BASE 0xFE000000 -# define CFG_FLASH_SIZE 0x02000000 +# define CONFIG_SYS_FLASH_BASE 0xFE000000 +# define CONFIG_SYS_FLASH_SIZE 0x02000000 #elif CONFIG_TOTAL5200_REV==2 -# define CFG_FLASH_BASE 0xFA000000 -# define CFG_FLASH_SIZE 0x06000000 +# define CONFIG_SYS_FLASH_BASE 0xFA000000 +# define CONFIG_SYS_FLASH_SIZE 0x06000000 #endif /* CONFIG_TOTAL5200_REV */ -#if defined(CFG_LOWBOOT) +#if defined(CONFIG_SYS_LOWBOOT) # define CONFIG_ENV_ADDR 0xFE040000 -#else /* CFG_LOWBOOT */ +#else /* CONFIG_SYS_LOWBOOT */ # define CONFIG_ENV_ADDR 0xFFF40000 -#endif /* CFG_LOWBOOT */ +#endif /* CONFIG_SYS_LOWBOOT */ /* * Environment settings @@ -240,29 +240,29 @@ /* * Memory map */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 -#define CFG_MBAR 0xF0000000 /* 64 kB */ -#define CFG_FPGA_BASE 0xF0010000 /* 64 kB */ -#define CFG_CPLD_BASE 0xF0020000 /* 64 kB */ -#define CFG_LCD_BASE 0xF1000000 /* 4096 kB */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */ +#define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */ +#define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */ +#define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */ /* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration @@ -293,32 +293,32 @@ * PSC1: reset default, changed in AC'97 driver 000 * */ -#define CFG_GPS_PORT_CONFIG 0x00000C10 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10 /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif @@ -326,11 +326,11 @@ * Various low-level settings */ #if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 #endif #if defined (CONFIG_MGT5100) @@ -338,43 +338,43 @@ #endif #if CONFIG_TOTAL5200_REV==1 -# define CFG_BOOTCS_START CFG_FLASH_BASE -# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CFG_CS0_START CFG_FLASH_BASE -# define CFG_CS0_SIZE 0x02000000 /* 32 MB */ +# define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ +# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +# define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */ #else -# define CFG_BOOTCS_START (CFG_CS4_START + CFG_CS4_SIZE) -# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CFG_CS4_START (CFG_CS5_START + CFG_CS5_SIZE) -# define CFG_CS4_SIZE 0x02000000 /* 32 MB */ -# define CFG_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CFG_CS5_START CFG_FLASH_BASE -# define CFG_CS5_SIZE 0x02000000 /* 32 MB */ -# define CFG_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE) +# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ +# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE) +# define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */ +# define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ +# define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE +# define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */ +# define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ #endif -#define CFG_CS1_START CFG_FPGA_BASE -#define CFG_CS1_SIZE 0x00010000 /* 64 kB */ -#define CFG_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ +#define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE +#define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */ +#define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ -#define CFG_CS2_START CFG_LCD_BASE -#define CFG_CS2_SIZE 0x00400000 /* 4096 kB */ -#define CFG_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */ +#define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE +#define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */ +#define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */ #if CONFIG_TOTAL5200_REV==1 -# define CFG_CS3_START CFG_CPLD_BASE -# define CFG_CS3_SIZE 0x00010000 /* 64 kB */ -# define CFG_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ +# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE +# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ +# define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ #else -# define CFG_CS3_START CFG_CPLD_BASE -# define CFG_CS3_SIZE 0x00010000 /* 64 kB */ -# define CFG_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ +# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE +# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ +# define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ #endif -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 /*----------------------------------------------------------------------- * USB stuff @@ -396,23 +396,23 @@ #define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA /* Offset for data I/O */ -#define CFG_ATA_DATA_OFFSET (0x0060) +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* Offset for normal register accesses */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for alternate registers */ -#define CFG_ATA_ALT_OFFSET (0x005C) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* Interval between registers */ -#define CFG_ATA_STRIDE 4 +#define CONFIG_SYS_ATA_STRIDE 4 #endif /* __CONFIG_H */ |