diff options
Diffstat (limited to 'include/configs/PLU405.h')
| -rw-r--r-- | include/configs/PLU405.h | 230 |
1 files changed, 115 insertions, 115 deletions
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 337cbfb1e..675dbe667 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -49,7 +49,7 @@ #define CONFIG_PREBOOT /* enable preboot variable */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_NET_MULTI 1 #undef CONFIG_HAS_ETH1 @@ -103,53 +103,53 @@ #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ +#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#undef CFG_HUSH_PARSER /* use "hush" command parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ +#define CONFIG_SYS_BASE_BAUD 691200 #undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ @@ -166,23 +166,23 @@ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /* * NAND-FLASH stuff */ -#define CFG_NAND_BASE_LIST {CFG_NAND_BASE} +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} #define NAND_MAX_CHIPS 1 -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define NAND_BIG_DELAY_US 25 -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ +#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ -#define CFG_NAND_QUIET 1 +#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ +#define CONFIG_SYS_NAND_QUIET 1 /* * PCI stuff @@ -200,15 +200,15 @@ #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CFG_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */ /* * IDE/ATA stuff @@ -217,58 +217,58 @@ #undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET 1 /* reset for ide supported */ -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ /* max. 1 drives per IDE bus */ -#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) -#define CFG_ATA_BASE_ADDR 0xF0100000 -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ -#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * FLASH organization */ #define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CFG_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */ -#define CFG_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */ +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */ /* * The following defines are added for buggy IOP480 byte interface. * All other boards should use the standard values (CPCI405 etc.) */ -#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ -#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ -#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ /* * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFFA0000 -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384kB for Monitor */ -#define CFG_MALLOC_LEN (384 * 1024) /* Reserve 384kB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFFA0000 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserve 384kB for malloc() */ /* * Environment Variable setup @@ -281,20 +281,20 @@ * I2C EEPROM (24WC16) for environment */ #define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */ -#define CFG_EEPROM_WREN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */ +#define CONFIG_SYS_EEPROM_WREN 1 /* 24WC16 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */ /* 16 byte page write mode using */ /* last 4 bits of the address */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ /* * External Bus Controller (EBC) Setup @@ -304,69 +304,69 @@ #define DUART1_BA 0xF0000408 /* DUART Base Address */ #define RTC_BA 0xF0000500 /* RTC Base Address */ #define VGA_BA 0xF1000000 /* Epson VGA Base Address */ -#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */ +#define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */ /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ /* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */ -#define CFG_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0AP 0x92015480 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ -#define CFG_EBC_PB0CR 0xFFC5A000 +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1AP 0x92015480 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB1CR 0xF4018000 +#define CONFIG_SYS_EBC_PB1CR 0xF4018000 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */ /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB2AP 0x010053C0 +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB2CR 0xF0018000 +#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */ /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3AP 0x010053C0 +#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ -#define CFG_EBC_PB3CR 0xF011A000 +#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* * FPGA stuff */ -#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */ +#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */ /* FPGA internal regs */ -#define CFG_FPGA_CTRL 0x000 +#define CONFIG_SYS_FPGA_CTRL 0x000 /* FPGA Control Reg */ -#define CFG_FPGA_CTRL_CF_RESET 0x0001 -#define CFG_FPGA_CTRL_WDI 0x0002 -#define CFG_FPGA_CTRL_PS2_RESET 0x0020 +#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 +#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 +#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 -#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ /* FPGA program pin configuration */ -#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ /* * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CFG_TEMP_STACK_OCM 1 +#define CONFIG_SYS_TEMP_STACK_OCM 1 /* On Chip Memory location */ -#define CFG_OCM_DATA_ADDR 0xF8000000 -#define CFG_OCM_DATA_SIZE 0x1000 -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Definitions for GPIO setup (PPC405EP specific) @@ -380,16 +380,16 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CFG_GPIO0_OSRH 0x00000550 -#define CFG_GPIO0_OSRL 0x00000110 -#define CFG_GPIO0_ISR1H 0x00000000 -#define CFG_GPIO0_ISR1L 0x15555445 -#define CFG_GPIO0_TSRH 0x00000000 -#define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0x77FE0014 +#define CONFIG_SYS_GPIO0_OSRH 0x00000550 +#define CONFIG_SYS_GPIO0_OSRL 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TCR 0x77FE0014 -#define CFG_DUART_RST (0x80000000 >> 14) -#define CFG_EEPROM_WP (0x80000000 >> 0) +#define CONFIG_SYS_DUART_RST (0x80000000 >> 14) +#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0) /* * Internal Definitions @@ -421,9 +421,9 @@ */ #define CONFIG_USB_OHCI_NEW 1 #define CONFIG_PCI_OHCI 1 -#define CFG_OHCI_SWAP_REG_ACCESS 1 -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 -#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" #define CONFIG_USB_STORAGE 1 #endif /* __CONFIG_H */ |