diff options
Diffstat (limited to 'include/configs/CCM.h')
| -rw-r--r-- | include/configs/CCM.h | 190 |
1 files changed, 95 insertions, 95 deletions
diff --git a/include/configs/CCM.h b/include/configs/CCM.h index 435e8ecf5..d1c293ff0 100644 --- a/include/configs/CCM.h +++ b/include/configs/CCM.h @@ -65,7 +65,7 @@ "bootm" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #define CONFIG_WATCHDOG 1 /* watchdog enabled */ @@ -86,9 +86,9 @@ * far enough from the start of the data area (as well as from the * stack pointer). * ---------------------------------------------------------------- */ -#define CFG_SPI_INIT_OFFSET 0xB00 +#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */ #define CONFIG_MAC_PARTITION /* nod used yet */ @@ -120,46 +120,46 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ -#define CFG_LOAD_ADDR 0x00100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ /* Ethernet hardware configuration done using port pins */ -#define CFG_PA_ETH_RESET 0x0200 /* PA 6 */ -#define CFG_PA_ETH_MDDIS 0x4000 /* PA 1 */ -#define CFG_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */ -#define CFG_PB_ETH_CFG1 0x00000400 /* PB 21 */ -#define CFG_PB_ETH_CFG2 0x00000200 /* PB 22 */ -#define CFG_PB_ETH_CFG3 0x00000100 /* PB 23 */ +#define CONFIG_SYS_PA_ETH_RESET 0x0200 /* PA 6 */ +#define CONFIG_SYS_PA_ETH_MDDIS 0x4000 /* PA 1 */ +#define CONFIG_SYS_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */ +#define CONFIG_SYS_PB_ETH_CFG1 0x00000400 /* PB 21 */ +#define CONFIG_SYS_PB_ETH_CFG2 0x00000200 /* PB 22 */ +#define CONFIG_SYS_PB_ETH_CFG3 0x00000100 /* PB 23 */ /* Ethernet settings: * MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex */ -#define CFG_ETH_MDDIS_VALUE 0 -#define CFG_ETH_CFG1_VALUE 1 -#define CFG_ETH_CFG2_VALUE 1 -#define CFG_ETH_CFG3_VALUE 1 +#define CONFIG_SYS_ETH_MDDIS_VALUE 0 +#define CONFIG_SYS_ETH_CFG1_VALUE 1 +#define CONFIG_SYS_ETH_CFG2_VALUE 1 +#define CONFIG_SYS_ETH_CFG3_VALUE 1 /* PUMA configuration */ -#define CFG_PC_PUMA_PROG 0x0200 /* PC 6 */ -#define CFG_PC_PUMA_DONE 0x0008 /* PC 12 */ -#define CFG_PC_PUMA_INIT 0x0004 /* PC 13 */ +#define CONFIG_SYS_PC_PUMA_PROG 0x0200 /* PC 6 */ +#define CONFIG_SYS_PC_PUMA_DONE 0x0008 /* PC 12 */ +#define CONFIG_SYS_PC_PUMA_INIT 0x0004 /* PC 13 */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings @@ -169,52 +169,52 @@ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ -#define CFG_IMMR 0xF0000000 +#define CONFIG_SYS_IMMR 0xF0000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Address accessed to reset the board - must not be mapped/assigned */ -#define CFG_RESET_ADDRESS 0xFEFFFFFF +#define CONFIG_SYS_RESET_ADDRESS 0xFEFFFFFF /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0x40000000 #if defined(DEBUG) -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #else -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ #endif -#define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #if 1 /* Start port with environment in flash; switch to SPI EEPROM later */ @@ -235,15 +235,15 @@ /*----------------------------------------------------------------------- * Hardware Information Block */ -#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ +#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 @@ -252,10 +252,10 @@ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) -#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else -#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWP) #endif @@ -264,27 +264,27 @@ *----------------------------------------------------------------------- * we must activate GPL5 in the SIUMCR for CAN */ -#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ -#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) +#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 11-27 *----------------------------------------------------------------------- */ -#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) +#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ -#define CFG_PISCR (PISCR_PS | PISCR_PITF) +#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 @@ -295,10 +295,10 @@ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! */ #ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ -#define CFG_PLPRCR \ +#define CONFIG_SYS_PLPRCR \ ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST ) #else /* up to 50 MHz we use a 1:1 clock */ -#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) +#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) #endif /* CCM_80MHz */ /*----------------------------------------------------------------------- @@ -309,12 +309,12 @@ */ #define SCCR_MASK SCCR_EBDF11 #ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ -#define CFG_SCCR (/* SCCR_TBS | */ \ +#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ \ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ SCCR_DFALCD00) #else /* up to 50 MHz we use a 1:1 clock */ -#define CFG_SCCR (SCCR_TBS | \ +#define CONFIG_SYS_SCCR (SCCR_TBS | \ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ SCCR_DFALCD00) @@ -325,14 +325,14 @@ * Interrupt Levels *----------------------------------------------------------------------- */ -#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ +#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- * */ -#define CFG_DER 0 +#define CONFIG_SYS_DER 0 /* * Init Memory Controller: @@ -347,20 +347,20 @@ * restrict access enough to keep SRAM working (if any) * but not too much to meddle with FLASH accesses */ -#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ +#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ /* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ -#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ +#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ OR_SCY_5_CLK | OR_EHTR) -#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) -#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) -#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) +#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) -#define CFG_OR1_REMAP CFG_OR0_REMAP -#define CFG_OR1_PRELIM CFG_OR0_PRELIM -#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) +#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM +#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) /* * BR2 and OR2 (SDRAM) @@ -371,18 +371,18 @@ #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CFG_OR_TIMING_SDRAM 0x00000A00 +#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 -#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) -#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) +#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) /* * BR3 and OR3 (CAN Controller) */ -#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ -#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ -#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI) -#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ +#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ +#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI) +#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \ BR_PS_8 | BR_MS_UPMB | BR_V ) /* @@ -409,8 +409,8 @@ #define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) #define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING) -#define CFG_BR4_PRELIM PUMA_CONF_BR_READ -#define CFG_OR4_PRELIM PUMA_CONF_OR_READ +#define CONFIG_SYS_BR4_PRELIM PUMA_CONF_BR_READ +#define CONFIG_SYS_OR4_PRELIM PUMA_CONF_OR_READ /* * BR5/OR5: PUMA: SMA Bus 8 Bit @@ -420,8 +420,8 @@ #define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */ #define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) -#define CFG_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) -#define CFG_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) +#define CONFIG_SYS_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) /* * BR6/OR6: PUMA: SMA Bus 16 Bit @@ -431,8 +431,8 @@ #define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */ #define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) -#define CFG_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CFG_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) +#define CONFIG_SYS_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) /* * BR7/OR7: PUMA: external Flash @@ -442,8 +442,8 @@ #define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */ #define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) -#define CFG_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) -#define CFG_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA) +#define CONFIG_SYS_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA) /* @@ -451,26 +451,26 @@ */ /* periodic timer for refresh */ -#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ +#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ +#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MAMR settings for SDRAM */ /* 8 column SDRAM */ -#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ +#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* 9 column SDRAM */ -#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ +#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |