diff options
Diffstat (limited to 'drivers')
103 files changed, 11815 insertions, 1600 deletions
diff --git a/drivers/Makefile b/drivers/Makefile index 9cec2ba6f..5d03f37a1 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -1,8 +1,8 @@ -obj-y += bios_emulator/ +obj-$(CONFIG_BIOSEMU) += bios_emulator/ obj-y += block/ obj-$(CONFIG_BOOTCOUNT_LIMIT) += bootcount/ obj-y += crypto/ -obj-y += fpga/ +obj-$(CONFIG_FPGA) += fpga/ obj-y += hwmon/ obj-y += misc/ obj-y += pcmcia/ @@ -13,3 +13,4 @@ obj-y += tpm/ obj-y += twserial/ obj-y += video/ obj-y += watchdog/ +obj-$(CONFIG_QE) += qe/ diff --git a/drivers/bios_emulator/Makefile b/drivers/bios_emulator/Makefile index dd42e0f76..52a2ceb47 100644 --- a/drivers/bios_emulator/Makefile +++ b/drivers/bios_emulator/Makefile @@ -1,8 +1,6 @@ X86DIR = x86emu -$(shell mkdir -p $(obj)$(X86DIR)) - -obj-$(CONFIG_BIOSEMU) = atibios.o biosemu.o besys.o bios.o \ +obj-y = atibios.o biosemu.o besys.o bios.o \ $(X86DIR)/decode.o \ $(X86DIR)/ops2.o \ $(X86DIR)/ops.o \ @@ -10,9 +8,8 @@ obj-$(CONFIG_BIOSEMU) = atibios.o biosemu.o besys.o bios.o \ $(X86DIR)/sys.o \ $(X86DIR)/debug.o -EXTRA_CFLAGS += -I. -I./include -I$(TOPDIR)/include \ +EXTRA_CFLAGS += -I. -I./include \ -D__PPC__ -D__BIG_ENDIAN__ CFLAGS += $(EXTRA_CFLAGS) -HOSTCFLAGS += $(EXTRA_CFLAGS) CPPFLAGS += $(EXTRA_CFLAGS) diff --git a/drivers/block/ahci.c b/drivers/block/ahci.c index 0daad364d..e64df4f98 100644 --- a/drivers/block/ahci.c +++ b/drivers/block/ahci.c @@ -379,6 +379,11 @@ static int ahci_init_one(pci_dev_t pdev) int rc; probe_ent = malloc(sizeof(struct ahci_probe_ent)); + if (!probe_ent) { + printf("%s: No memory for probe_ent\n", __func__); + return -ENOMEM; + } + memset(probe_ent, 0, sizeof(struct ahci_probe_ent)); probe_ent->dev = pdev; @@ -503,7 +508,7 @@ static int ahci_port_start(u8 port) mem = (u32) malloc(AHCI_PORT_PRIV_DMA_SZ + 2048); if (!mem) { free(pp); - printf("No mem for table!\n"); + printf("%s: No mem for table!\n", __func__); return -ENOMEM; } @@ -618,7 +623,7 @@ static int ata_scsiop_inquiry(ccb *pccb) 95 - 4, }; u8 fis[20]; - u16 *tmpid; + ALLOC_CACHE_ALIGN_BUFFER(u16, tmpid, ATA_ID_WORDS); u8 port; /* Clean ccb data buffer */ @@ -637,14 +642,10 @@ static int ata_scsiop_inquiry(ccb *pccb) /* Read id from sata */ port = pccb->target; - tmpid = malloc(ATA_ID_WORDS * 2); - if (!tmpid) - return -ENOMEM; if (ahci_device_data_io(port, (u8 *) &fis, sizeof(fis), (u8 *)tmpid, ATA_ID_WORDS * 2, 0)) { debug("scsi_ahci: SCSI inquiry command failure.\n"); - free(tmpid); return -EIO; } @@ -889,6 +890,11 @@ int ahci_init(u32 base) u32 linkmap; probe_ent = malloc(sizeof(struct ahci_probe_ent)); + if (!probe_ent) { + printf("%s: No memory for probe_ent\n", __func__); + return -ENOMEM; + } + memset(probe_ent, 0, sizeof(struct ahci_probe_ent)); probe_ent->host_flags = ATA_FLAG_SATA diff --git a/drivers/ddr/fsl/Makefile b/drivers/ddr/fsl/Makefile new file mode 100644 index 000000000..265204f31 --- /dev/null +++ b/drivers/ddr/fsl/Makefile @@ -0,0 +1,34 @@ +# +# Copyright 2008-2011 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License +# Version 2 as published by the Free Software Foundation. +# + +obj-$(CONFIG_SYS_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \ + lc_common_dimm_params.o + +obj-$(CONFIG_SYS_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \ + lc_common_dimm_params.o + +obj-$(CONFIG_SYS_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \ + lc_common_dimm_params.o +ifdef CONFIG_DDR_SPD +SPD := y +endif +ifdef CONFIG_SPD_EEPROM +SPD := y +endif +ifdef SPD +obj-$(CONFIG_SYS_FSL_DDR1) += ddr1_dimm_params.o +obj-$(CONFIG_SYS_FSL_DDR2) += ddr2_dimm_params.o +obj-$(CONFIG_SYS_FSL_DDR3) += ddr3_dimm_params.o +endif + +obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o +obj-$(CONFIG_SYS_FSL_DDRC_GEN1) += mpc85xx_ddr_gen1.o +obj-$(CONFIG_SYS_FSL_DDRC_GEN2) += mpc85xx_ddr_gen2.o +obj-$(CONFIG_SYS_FSL_DDRC_GEN3) += mpc85xx_ddr_gen3.o +obj-$(CONFIG_SYS_FSL_DDR_86XX) += mpc86xx_ddr.o +obj-$(CONFIG_SYS_FSL_DDRC_ARM_GEN3) += arm_ddr_gen3.o diff --git a/drivers/ddr/fsl/arm_ddr_gen3.c b/drivers/ddr/fsl/arm_ddr_gen3.c new file mode 100644 index 000000000..bf113908f --- /dev/null +++ b/drivers/ddr/fsl/arm_ddr_gen3.c @@ -0,0 +1,213 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Derived from mpc85xx_ddr_gen3.c, removed all workarounds + */ + +#include <common.h> +#include <asm/io.h> +#include <fsl_ddr_sdram.h> +#include <asm/processor.h> +#include <fsl_immap.h> + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + + +/* + * regs has the to-be-set values for DDR controller registers + * ctrl_num is the DDR controller number + * step: 0 goes through the initialization in one pass + * 1 sets registers and returns before enabling controller + * 2 resumes from step 1 and continues to initialize + * Dividing the initialization to two steps to deassert DDR reset signal + * to comply with JEDEC specs for RDIMMs. + */ +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step) +{ + unsigned int i, bus_width; + struct ccsr_ddr __iomem *ddr; + u32 temp_sdram_cfg; + u32 total_gb_size_per_controller; + int timeout; + + switch (ctrl_num) { + case 0: + ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR; + break; +#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1) + case 1: + ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR; + break; +#endif +#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2) + case 2: + ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR; + break; +#endif +#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3) + case 3: + ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR; + break; +#endif + default: + printf("%s unexpected ctrl_num = %u\n", __func__, ctrl_num); + return; + } + + if (step == 2) + goto step2; + + if (regs->ddr_eor) + out_be32(&ddr->eor, regs->ddr_eor); + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + out_be32(&ddr->cs0_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs0_config, regs->cs[i].config); + out_be32(&ddr->cs0_config_2, regs->cs[i].config_2); + + } else if (i == 1) { + out_be32(&ddr->cs1_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs1_config, regs->cs[i].config); + out_be32(&ddr->cs1_config_2, regs->cs[i].config_2); + + } else if (i == 2) { + out_be32(&ddr->cs2_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs2_config, regs->cs[i].config); + out_be32(&ddr->cs2_config_2, regs->cs[i].config_2); + + } else if (i == 3) { + out_be32(&ddr->cs3_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs3_config, regs->cs[i].config); + out_be32(&ddr->cs3_config_2, regs->cs[i].config_2); + } + } + + out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3); + out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0); + out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2); + out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); + out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2); + out_be32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3); + out_be32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4); + out_be32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5); + out_be32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6); + out_be32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7); + out_be32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8); + out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); + out_be32(&ddr->sdram_data_init, regs->ddr_data_init); + out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); + out_be32(&ddr->init_addr, regs->ddr_init_addr); + out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr); + + out_be32(&ddr->timing_cfg_4, regs->timing_cfg_4); + out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5); + out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl); + out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl); +#ifndef CONFIG_SYS_FSL_DDR_EMU + /* + * Skip these two registers if running on emulator + * because emulator doesn't have skew between bytes. + */ + + if (regs->ddr_wrlvl_cntl_2) + out_be32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2); + if (regs->ddr_wrlvl_cntl_3) + out_be32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3); +#endif + + out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr); + out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1); + out_be32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2); + out_be32(&ddr->ddr_cdr1, regs->ddr_cdr1); + out_be32(&ddr->ddr_cdr2, regs->ddr_cdr2); + out_be32(&ddr->err_disable, regs->err_disable); + out_be32(&ddr->err_int_en, regs->err_int_en); + for (i = 0; i < 32; i++) { + if (regs->debug[i]) { + debug("Write to debug_%d as %08x\n", i + 1, + regs->debug[i]); + out_be32(&ddr->debug[i], regs->debug[i]); + } + } + + /* + * For RDIMMs, JEDEC spec requires clocks to be stable before reset is + * deasserted. Clocks start when any chip select is enabled and clock + * control register is set. Because all DDR components are connected to + * one reset signal, this needs to be done in two steps. Step 1 is to + * get the clocks started. Step 2 resumes after reset signal is + * deasserted. + */ + if (step == 1) { + udelay(200); + return; + } + +step2: + /* Set, but do not enable the memory */ + temp_sdram_cfg = regs->ddr_sdram_cfg; + temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg); + + /* + * 500 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + * DDR2 need 200 us, and DDR3 need 500 us from spec, + * we choose the max, that is 500 us for all of case. + */ + udelay(500); + asm volatile("dsb sy;isb"); + + /* Let the controller go */ + temp_sdram_cfg = in_be32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI; + out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN); + asm volatile("dsb sy;isb"); + + total_gb_size_per_controller = 0; + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (!(regs->cs[i].config & 0x80000000)) + continue; + total_gb_size_per_controller += 1 << ( + ((regs->cs[i].config >> 14) & 0x3) + 2 + + ((regs->cs[i].config >> 8) & 0x7) + 12 + + ((regs->cs[i].config >> 0) & 0x7) + 8 + + 3 - ((regs->ddr_sdram_cfg >> 19) & 0x3) - + 26); /* minus 26 (count of 64M) */ + } + if (regs->cs[0].config & 0x20000000) { + /* 2-way interleaving */ + total_gb_size_per_controller <<= 1; + } + /* + * total memory / bus width = transactions needed + * transactions needed / data rate = seconds + * to add plenty of buffer, double the time + * For example, 2GB on 666MT/s 64-bit bus takes about 402ms + * Let's wait for 800ms + */ + bus_width = 3 - ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK) + >> SDRAM_CFG_DBW_SHIFT); + timeout = ((total_gb_size_per_controller << (6 - bus_width)) * 100 / + (get_ddr_freq(0) >> 20)) << 1; + total_gb_size_per_controller >>= 4; /* shift down to gb size */ + debug("total %d GB\n", total_gb_size_per_controller); + debug("Need to wait up to %d * 10ms\n", timeout); + + /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */ + while ((in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) && + (timeout >= 0)) { + udelay(10000); /* throttle polling rate */ + timeout--; + } + + if (timeout <= 0) + printf("Waiting for D_INIT timeout. Memory may not work.\n"); +} diff --git a/drivers/ddr/fsl/ctrl_regs.c b/drivers/ddr/fsl/ctrl_regs.c new file mode 100644 index 000000000..6bf22cfbd --- /dev/null +++ b/drivers/ddr/fsl/ctrl_regs.c @@ -0,0 +1,1662 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. + * Based on code from spd_sdram.c + * Author: James Yang [at freescale.com] + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> +#include <fsl_immap.h> +#include <asm/io.h> + +#define _DDR_ADDR CONFIG_SYS_FSL_DDR_ADDR + +static u32 fsl_ddr_get_version(void) +{ + struct ccsr_ddr __iomem *ddr; + u32 ver_major_minor_errata; + + ddr = (void *)_DDR_ADDR; + ver_major_minor_errata = (in_be32(&ddr->ip_rev1) & 0xFFFF) << 8; + ver_major_minor_errata |= (in_be32(&ddr->ip_rev2) & 0xFF00) >> 8; + + return ver_major_minor_errata; +} + +unsigned int picos_to_mclk(unsigned int picos); + +/* + * Determine Rtt value. + * + * This should likely be either board or controller specific. + * + * Rtt(nominal) - DDR2: + * 0 = Rtt disabled + * 1 = 75 ohm + * 2 = 150 ohm + * 3 = 50 ohm + * Rtt(nominal) - DDR3: + * 0 = Rtt disabled + * 1 = 60 ohm + * 2 = 120 ohm + * 3 = 40 ohm + * 4 = 20 ohm + * 5 = 30 ohm + * + * FIXME: Apparently 8641 needs a value of 2 + * FIXME: Old code seys if 667 MHz or higher, use 3 on 8572 + * + * FIXME: There was some effort down this line earlier: + * + * unsigned int i; + * for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) { + * if (popts->dimmslot[i].num_valid_cs + * && (popts->cs_local_opts[2*i].odt_rd_cfg + * || popts->cs_local_opts[2*i].odt_wr_cfg)) { + * rtt = 2; + * break; + * } + * } + */ +static inline int fsl_ddr_get_rtt(void) +{ + int rtt; + +#if defined(CONFIG_SYS_FSL_DDR1) + rtt = 0; +#elif defined(CONFIG_SYS_FSL_DDR2) + rtt = 3; +#else + rtt = 0; +#endif + + return rtt; +} + +/* + * compute the CAS write latency according to DDR3 spec + * CWL = 5 if tCK >= 2.5ns + * 6 if 2.5ns > tCK >= 1.875ns + * 7 if 1.875ns > tCK >= 1.5ns + * 8 if 1.5ns > tCK >= 1.25ns + * 9 if 1.25ns > tCK >= 1.07ns + * 10 if 1.07ns > tCK >= 0.935ns + * 11 if 0.935ns > tCK >= 0.833ns + * 12 if 0.833ns > tCK >= 0.75ns + */ +static inline unsigned int compute_cas_write_latency(void) +{ + unsigned int cwl; + const unsigned int mclk_ps = get_memory_clk_period_ps(); + + if (mclk_ps >= 2500) + cwl = 5; + else if (mclk_ps >= 1875) + cwl = 6; + else if (mclk_ps >= 1500) + cwl = 7; + else if (mclk_ps >= 1250) + cwl = 8; + else if (mclk_ps >= 1070) + cwl = 9; + else if (mclk_ps >= 935) + cwl = 10; + else if (mclk_ps >= 833) + cwl = 11; + else if (mclk_ps >= 750) + cwl = 12; + else { + cwl = 12; + printf("Warning: CWL is out of range\n"); + } + return cwl; +} + +/* Chip Select Configuration (CSn_CONFIG) */ +static void set_csn_config(int dimm_number, int i, fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const dimm_params_t *dimm_params) +{ + unsigned int cs_n_en = 0; /* Chip Select enable */ + unsigned int intlv_en = 0; /* Memory controller interleave enable */ + unsigned int intlv_ctl = 0; /* Interleaving control */ + unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */ + unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */ + unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */ + unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */ + unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */ + unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */ + int go_config = 0; + + /* Compute CS_CONFIG only for existing ranks of each DIMM. */ + switch (i) { + case 0: + if (dimm_params[dimm_number].n_ranks > 0) { + go_config = 1; + /* These fields only available in CS0_CONFIG */ + if (!popts->memctl_interleaving) + break; + switch (popts->memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + intlv_en = popts->memctl_interleaving; + intlv_ctl = popts->memctl_interleaving_mode; + break; + default: + break; + } + } + break; + case 1: + if ((dimm_number == 0 && dimm_params[0].n_ranks > 1) || \ + (dimm_number == 1 && dimm_params[1].n_ranks > 0)) + go_config = 1; + break; + case 2: + if ((dimm_number == 0 && dimm_params[0].n_ranks > 2) || \ + (dimm_number >= 1 && dimm_params[dimm_number].n_ranks > 0)) + go_config = 1; + break; + case 3: + if ((dimm_number == 0 && dimm_params[0].n_ranks > 3) || \ + (dimm_number == 1 && dimm_params[1].n_ranks > 1) || \ + (dimm_number == 3 && dimm_params[3].n_ranks > 0)) + go_config = 1; + break; + default: + break; + } + if (go_config) { + unsigned int n_banks_per_sdram_device; + cs_n_en = 1; + ap_n_en = popts->cs_local_opts[i].auto_precharge; + odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg; + odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg; + n_banks_per_sdram_device + = dimm_params[dimm_number].n_banks_per_sdram_device; + ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2; + row_bits_cs_n = dimm_params[dimm_number].n_row_addr - 12; + col_bits_cs_n = dimm_params[dimm_number].n_col_addr - 8; + } + ddr->cs[i].config = (0 + | ((cs_n_en & 0x1) << 31) + | ((intlv_en & 0x3) << 29) + | ((intlv_ctl & 0xf) << 24) + | ((ap_n_en & 0x1) << 23) + + /* XXX: some implementation only have 1 bit starting at left */ + | ((odt_rd_cfg & 0x7) << 20) + + /* XXX: Some implementation only have 1 bit starting at left */ + | ((odt_wr_cfg & 0x7) << 16) + + | ((ba_bits_cs_n & 0x3) << 14) + | ((row_bits_cs_n & 0x7) << 8) + | ((col_bits_cs_n & 0x7) << 0) + ); + debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config); +} + +/* Chip Select Configuration 2 (CSn_CONFIG_2) */ +/* FIXME: 8572 */ +static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int pasr_cfg = 0; /* Partial array self refresh config */ + + ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24); + debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2); +} + +/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */ + +#if !defined(CONFIG_SYS_FSL_DDR1) +static inline int avoid_odt_overlap(const dimm_params_t *dimm_params) +{ +#if CONFIG_DIMM_SLOTS_PER_CTLR == 1 + if (dimm_params[0].n_ranks == 4) + return 1; +#endif + +#if CONFIG_DIMM_SLOTS_PER_CTLR == 2 + if ((dimm_params[0].n_ranks == 2) && + (dimm_params[1].n_ranks == 2)) + return 1; + +#ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + if (dimm_params[0].n_ranks == 4) + return 1; +#endif +#endif + return 0; +} + +/* + * DDR SDRAM Timing Configuration 0 (TIMING_CFG_0) + * + * Avoid writing for DDR I. The new PQ38 DDR controller + * dreams up non-zero default values to be backwards compatible. + */ +static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const dimm_params_t *dimm_params) +{ + unsigned char trwt_mclk = 0; /* Read-to-write turnaround */ + unsigned char twrt_mclk = 0; /* Write-to-read turnaround */ + /* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */ + unsigned char trrt_mclk = 0; /* Read-to-read turnaround */ + unsigned char twwt_mclk = 0; /* Write-to-write turnaround */ + + /* Active powerdown exit timing (tXARD and tXARDS). */ + unsigned char act_pd_exit_mclk; + /* Precharge powerdown exit timing (tXP). */ + unsigned char pre_pd_exit_mclk; + /* ODT powerdown exit timing (tAXPD). */ + unsigned char taxpd_mclk; + /* Mode register set cycle time (tMRD). */ + unsigned char tmrd_mclk; + +#ifdef CONFIG_SYS_FSL_DDR3 + /* + * (tXARD and tXARDS). Empirical? + * The DDR3 spec has not tXARD, + * we use the tXP instead of it. + * tXP=max(3nCK, 7.5ns) for DDR3. + * spec has not the tAXPD, we use + * tAXPD=1, need design to confirm. + */ + int tXP = max((get_memory_clk_period_ps() * 3), 7500); /* unit=ps */ + unsigned int data_rate = get_ddr_freq(0); + tmrd_mclk = 4; + /* set the turnaround time */ + + /* + * for single quad-rank DIMM and two dual-rank DIMMs + * to avoid ODT overlap + */ + if (avoid_odt_overlap(dimm_params)) { + twwt_mclk = 2; + trrt_mclk = 1; + } + /* for faster clock, need more time for data setup */ + trwt_mclk = (data_rate/1000000 > 1800) ? 2 : 1; + + if ((data_rate/1000000 > 1150) || (popts->memctl_interleaving)) + twrt_mclk = 1; + + if (popts->dynamic_power == 0) { /* powerdown is not used */ + act_pd_exit_mclk = 1; + pre_pd_exit_mclk = 1; + taxpd_mclk = 1; + } else { + /* act_pd_exit_mclk = tXARD, see above */ + act_pd_exit_mclk = picos_to_mclk(tXP); + /* Mode register MR0[A12] is '1' - fast exit */ + pre_pd_exit_mclk = act_pd_exit_mclk; + taxpd_mclk = 1; + } +#else /* CONFIG_SYS_FSL_DDR2 */ + /* + * (tXARD and tXARDS). Empirical? + * tXARD = 2 for DDR2 + * tXP=2 + * tAXPD=8 + */ + act_pd_exit_mclk = 2; + pre_pd_exit_mclk = 2; + taxpd_mclk = 8; + tmrd_mclk = 2; +#endif + + if (popts->trwt_override) + trwt_mclk = popts->trwt; + + ddr->timing_cfg_0 = (0 + | ((trwt_mclk & 0x3) << 30) /* RWT */ + | ((twrt_mclk & 0x3) << 28) /* WRT */ + | ((trrt_mclk & 0x3) << 26) /* RRT */ + | ((twwt_mclk & 0x3) << 24) /* WWT */ + | ((act_pd_exit_mclk & 0xf) << 20) /* ACT_PD_EXIT */ + | ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */ + | ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */ + | ((tmrd_mclk & 0x1f) << 0) /* MRS_CYC */ + ); + debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0); +} +#endif /* defined(CONFIG_SYS_FSL_DDR2) */ + +/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */ +static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency) +{ + /* Extended precharge to activate interval (tRP) */ + unsigned int ext_pretoact = 0; + /* Extended Activate to precharge interval (tRAS) */ + unsigned int ext_acttopre = 0; + /* Extended activate to read/write interval (tRCD) */ + unsigned int ext_acttorw = 0; + /* Extended refresh recovery time (tRFC) */ + unsigned int ext_refrec; + /* Extended MCAS latency from READ cmd */ + unsigned int ext_caslat = 0; + /* Extended additive latency */ + unsigned int ext_add_lat = 0; + /* Extended last data to precharge interval (tWR) */ + unsigned int ext_wrrec = 0; + /* Control Adjust */ + unsigned int cntl_adj = 0; + + ext_pretoact = picos_to_mclk(common_dimm->trp_ps) >> 4; + ext_acttopre = picos_to_mclk(common_dimm->tras_ps) >> 4; + ext_acttorw = picos_to_mclk(common_dimm->trcd_ps) >> 4; + ext_caslat = (2 * cas_latency - 1) >> 4; + ext_add_lat = additive_latency >> 4; + ext_refrec = (picos_to_mclk(common_dimm->trfc_ps) - 8) >> 4; + /* ext_wrrec only deals with 16 clock and above, or 14 with OTF */ + ext_wrrec = (picos_to_mclk(common_dimm->twr_ps) + + (popts->otf_burst_chop_en ? 2 : 0)) >> 4; + + ddr->timing_cfg_3 = (0 + | ((ext_pretoact & 0x1) << 28) + | ((ext_acttopre & 0x3) << 24) + | ((ext_acttorw & 0x1) << 22) + | ((ext_refrec & 0x1F) << 16) + | ((ext_caslat & 0x3) << 12) + | ((ext_add_lat & 0x1) << 10) + | ((ext_wrrec & 0x1) << 8) + | ((cntl_adj & 0x7) << 0) + ); + debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3); +} + +/* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */ +static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency) +{ + /* Precharge-to-activate interval (tRP) */ + unsigned char pretoact_mclk; + /* Activate to precharge interval (tRAS) */ + unsigned char acttopre_mclk; + /* Activate to read/write interval (tRCD) */ + unsigned char acttorw_mclk; + /* CASLAT */ + unsigned char caslat_ctrl; + /* Refresh recovery time (tRFC) ; trfc_low */ + unsigned char refrec_ctrl; + /* Last data to precharge minimum interval (tWR) */ + unsigned char wrrec_mclk; + /* Activate-to-activate interval (tRRD) */ + unsigned char acttoact_mclk; + /* Last write data pair to read command issue interval (tWTR) */ + unsigned char wrtord_mclk; + /* DDR_SDRAM_MODE doesn't support 9,11,13,15 */ + static const u8 wrrec_table[] = { + 1, 2, 3, 4, 5, 6, 7, 8, 10, 10, 12, 12, 14, 14, 0, 0}; + + pretoact_mclk = picos_to_mclk(common_dimm->trp_ps); + acttopre_mclk = picos_to_mclk(common_dimm->tras_ps); + acttorw_mclk = picos_to_mclk(common_dimm->trcd_ps); + + /* + * Translate CAS Latency to a DDR controller field value: + * + * CAS Lat DDR I DDR II Ctrl + * Clocks SPD Bit SPD Bit Value + * ------- ------- ------- ----- + * 1.0 0 0001 + * 1.5 1 0010 + * 2.0 2 2 0011 + * 2.5 3 0100 + * 3.0 4 3 0101 + * 3.5 5 0110 + * 4.0 4 0111 + * 4.5 1000 + * 5.0 5 1001 + */ +#if defined(CONFIG_SYS_FSL_DDR1) + caslat_ctrl = (cas_latency + 1) & 0x07; +#elif defined(CONFIG_SYS_FSL_DDR2) + caslat_ctrl = 2 * cas_latency - 1; +#else + /* + * if the CAS latency more than 8 cycle, + * we need set extend bit for it at + * TIMING_CFG_3[EXT_CASLAT] + */ + caslat_ctrl = 2 * cas_latency - 1; +#endif + + refrec_ctrl = picos_to_mclk(common_dimm->trfc_ps) - 8; + wrrec_mclk = picos_to_mclk(common_dimm->twr_ps); + + if (wrrec_mclk > 16) + printf("Error: WRREC doesn't support more than 16 clocks\n"); + else + wrrec_mclk = wrrec_table[wrrec_mclk - 1]; + if (popts->otf_burst_chop_en) + wrrec_mclk += 2; + + acttoact_mclk = picos_to_mclk(common_dimm->trrd_ps); + /* + * JEDEC has min requirement for tRRD + */ +#if defined(CONFIG_SYS_FSL_DDR3) + if (acttoact_mclk < 4) + acttoact_mclk = 4; +#endif + wrtord_mclk = picos_to_mclk(common_dimm->twtr_ps); + /* + * JEDEC has some min requirements for tWTR + */ +#if defined(CONFIG_SYS_FSL_DDR2) + if (wrtord_mclk < 2) + wrtord_mclk = 2; +#elif defined(CONFIG_SYS_FSL_DDR3) + if (wrtord_mclk < 4) + wrtord_mclk = 4; +#endif + if (popts->otf_burst_chop_en) + wrtord_mclk += 2; + + ddr->timing_cfg_1 = (0 + | ((pretoact_mclk & 0x0F) << 28) + | ((acttopre_mclk & 0x0F) << 24) + | ((acttorw_mclk & 0xF) << 20) + | ((caslat_ctrl & 0xF) << 16) + | ((refrec_ctrl & 0xF) << 12) + | ((wrrec_mclk & 0x0F) << 8) + | ((acttoact_mclk & 0x0F) << 4) + | ((wrtord_mclk & 0x0F) << 0) + ); + debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1); +} + +/* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */ +static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency) +{ + /* Additive latency */ + unsigned char add_lat_mclk; + /* CAS-to-preamble override */ + unsigned short cpo; + /* Write latency */ + unsigned char wr_lat; + /* Read to precharge (tRTP) */ + unsigned char rd_to_pre; + /* Write command to write data strobe timing adjustment */ + unsigned char wr_data_delay; + /* Minimum CKE pulse width (tCKE) */ + unsigned char cke_pls; + /* Window for four activates (tFAW) */ + unsigned short four_act; + + /* FIXME add check that this must be less than acttorw_mclk */ + add_lat_mclk = additive_latency; + cpo = popts->cpo_override; + +#if defined(CONFIG_SYS_FSL_DDR1) + /* + * This is a lie. It should really be 1, but if it is + * set to 1, bits overlap into the old controller's + * otherwise unused ACSM field. If we leave it 0, then + * the HW will magically treat it as 1 for DDR 1. Oh Yea. + */ + wr_lat = 0; +#elif defined(CONFIG_SYS_FSL_DDR2) + wr_lat = cas_latency - 1; +#else + wr_lat = compute_cas_write_latency(); +#endif + + rd_to_pre = picos_to_mclk(common_dimm->trtp_ps); + /* + * JEDEC has some min requirements for tRTP + */ +#if defined(CONFIG_SYS_FSL_DDR2) + if (rd_to_pre < 2) + rd_to_pre = 2; +#elif defined(CONFIG_SYS_FSL_DDR3) + if (rd_to_pre < 4) + rd_to_pre = 4; +#endif + if (popts->otf_burst_chop_en) + rd_to_pre += 2; /* according to UM */ + + wr_data_delay = popts->write_data_delay; + cke_pls = picos_to_mclk(popts->tcke_clock_pulse_width_ps); + four_act = picos_to_mclk(popts->tfaw_window_four_activates_ps); + + ddr->timing_cfg_2 = (0 + | ((add_lat_mclk & 0xf) << 28) + | ((cpo & 0x1f) << 23) + | ((wr_lat & 0xf) << 19) + | ((rd_to_pre & RD_TO_PRE_MASK) << RD_TO_PRE_SHIFT) + | ((wr_data_delay & WR_DATA_DELAY_MASK) << WR_DATA_DELAY_SHIFT) + | ((cke_pls & 0x7) << 6) + | ((four_act & 0x3f) << 0) + ); + debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2); +} + +/* DDR SDRAM Register Control Word */ +static void set_ddr_sdram_rcw(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm) +{ + if (common_dimm->all_dimms_registered && + !common_dimm->all_dimms_unbuffered) { + if (popts->rcw_override) { + ddr->ddr_sdram_rcw_1 = popts->rcw_1; + ddr->ddr_sdram_rcw_2 = popts->rcw_2; + } else { + ddr->ddr_sdram_rcw_1 = + common_dimm->rcw[0] << 28 | \ + common_dimm->rcw[1] << 24 | \ + common_dimm->rcw[2] << 20 | \ + common_dimm->rcw[3] << 16 | \ + common_dimm->rcw[4] << 12 | \ + common_dimm->rcw[5] << 8 | \ + common_dimm->rcw[6] << 4 | \ + common_dimm->rcw[7]; + ddr->ddr_sdram_rcw_2 = + common_dimm->rcw[8] << 28 | \ + common_dimm->rcw[9] << 24 | \ + common_dimm->rcw[10] << 20 | \ + common_dimm->rcw[11] << 16 | \ + common_dimm->rcw[12] << 12 | \ + common_dimm->rcw[13] << 8 | \ + common_dimm->rcw[14] << 4 | \ + common_dimm->rcw[15]; + } + debug("FSLDDR: ddr_sdram_rcw_1 = 0x%08x\n", ddr->ddr_sdram_rcw_1); + debug("FSLDDR: ddr_sdram_rcw_2 = 0x%08x\n", ddr->ddr_sdram_rcw_2); + } +} + +/* DDR SDRAM control configuration (DDR_SDRAM_CFG) */ +static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm) +{ + unsigned int mem_en; /* DDR SDRAM interface logic enable */ + unsigned int sren; /* Self refresh enable (during sleep) */ + unsigned int ecc_en; /* ECC enable. */ + unsigned int rd_en; /* Registered DIMM enable */ + unsigned int sdram_type; /* Type of SDRAM */ + unsigned int dyn_pwr; /* Dynamic power management mode */ + unsigned int dbw; /* DRAM dta bus width */ + unsigned int eight_be = 0; /* 8-beat burst enable, DDR2 is zero */ + unsigned int ncap = 0; /* Non-concurrent auto-precharge */ + unsigned int threet_en; /* Enable 3T timing */ + unsigned int twot_en; /* Enable 2T timing */ + unsigned int ba_intlv_ctl; /* Bank (CS) interleaving control */ + unsigned int x32_en = 0; /* x32 enable */ + unsigned int pchb8 = 0; /* precharge bit 8 enable */ + unsigned int hse; /* Global half strength override */ + unsigned int mem_halt = 0; /* memory controller halt */ + unsigned int bi = 0; /* Bypass initialization */ + + mem_en = 1; + sren = popts->self_refresh_in_sleep; + if (common_dimm->all_dimms_ecc_capable) { + /* Allow setting of ECC only if all DIMMs are ECC. */ + ecc_en = popts->ecc_mode; + } else { + ecc_en = 0; + } + + if (common_dimm->all_dimms_registered && + !common_dimm->all_dimms_unbuffered) { + rd_en = 1; + twot_en = 0; + } else { + rd_en = 0; + twot_en = popts->twot_en; + } + + sdram_type = CONFIG_FSL_SDRAM_TYPE; + + dyn_pwr = popts->dynamic_power; + dbw = popts->data_bus_width; + /* 8-beat burst enable DDR-III case + * we must clear it when use the on-the-fly mode, + * must set it when use the 32-bits bus mode. + */ + if (sdram_type == SDRAM_TYPE_DDR3) { + if (popts->burst_length == DDR_BL8) + eight_be = 1; + if (popts->burst_length == DDR_OTF) + eight_be = 0; + if (dbw == 0x1) + eight_be = 1; + } + + threet_en = popts->threet_en; + ba_intlv_ctl = popts->ba_intlv_ctl; + hse = popts->half_strength_driver_enable; + + ddr->ddr_sdram_cfg = (0 + | ((mem_en & 0x1) << 31) + | ((sren & 0x1) << 30) + | ((ecc_en & 0x1) << 29) + | ((rd_en & 0x1) << 28) + | ((sdram_type & 0x7) << 24) + | ((dyn_pwr & 0x1) << 21) + | ((dbw & 0x3) << 19) + | ((eight_be & 0x1) << 18) + | ((ncap & 0x1) << 17) + | ((threet_en & 0x1) << 16) + | ((twot_en & 0x1) << 15) + | ((ba_intlv_ctl & 0x7F) << 8) + | ((x32_en & 0x1) << 5) + | ((pchb8 & 0x1) << 4) + | ((hse & 0x1) << 3) + | ((mem_halt & 0x1) << 1) + | ((bi & 0x1) << 0) + ); + debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg); +} + +/* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */ +static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const unsigned int unq_mrs_en) +{ + unsigned int frc_sr = 0; /* Force self refresh */ + unsigned int sr_ie = 0; /* Self-refresh interrupt enable */ + unsigned int dll_rst_dis; /* DLL reset disable */ + unsigned int dqs_cfg; /* DQS configuration */ + unsigned int odt_cfg = 0; /* ODT configuration */ + unsigned int num_pr; /* Number of posted refreshes */ + unsigned int slow = 0; /* DDR will be run less than 1250 */ + unsigned int x4_en = 0; /* x4 DRAM enable */ + unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */ + unsigned int ap_en; /* Address Parity Enable */ + unsigned int d_init; /* DRAM data initialization */ + unsigned int rcw_en = 0; /* Register Control Word Enable */ + unsigned int md_en = 0; /* Mirrored DIMM Enable */ + unsigned int qd_en = 0; /* quad-rank DIMM Enable */ + int i; + + dll_rst_dis = 1; /* Make this configurable */ + dqs_cfg = popts->dqs_config; + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (popts->cs_local_opts[i].odt_rd_cfg + || popts->cs_local_opts[i].odt_wr_cfg) { + odt_cfg = SDRAM_CFG2_ODT_ONLY_READ; + break; + } + } + + num_pr = 1; /* Make this configurable */ + + /* + * 8572 manual says + * {TIMING_CFG_1[PRETOACT] + * + [DDR_SDRAM_CFG_2[NUM_PR] + * * ({EXT_REFREC || REFREC} + 8 + 2)]} + * << DDR_SDRAM_INTERVAL[REFINT] + */ +#if defined(CONFIG_SYS_FSL_DDR3) + obc_cfg = popts->otf_burst_chop_en; +#else + obc_cfg = 0; +#endif + +#if (CONFIG_SYS_FSL_DDR_VER >= FSL_DDR_VER_4_7) + slow = get_ddr_freq(0) < 1249000000; +#endif + + if (popts->registered_dimm_en) { + rcw_en = 1; + ap_en = popts->ap_en; + } else { + ap_en = 0; + } + + x4_en = popts->x4_en ? 1 : 0; + +#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Use the DDR controller to auto initialize memory. */ + d_init = popts->ecc_init_using_memctl; + ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE; + debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init); +#else + /* Memory will be initialized via DMA, or not at all. */ + d_init = 0; +#endif + +#if defined(CONFIG_SYS_FSL_DDR3) + md_en = popts->mirrored_dimm; +#endif + qd_en = popts->quad_rank_present ? 1 : 0; + ddr->ddr_sdram_cfg_2 = (0 + | ((frc_sr & 0x1) << 31) + | ((sr_ie & 0x1) << 30) + | ((dll_rst_dis & 0x1) << 29) + | ((dqs_cfg & 0x3) << 26) + | ((odt_cfg & 0x3) << 21) + | ((num_pr & 0xf) << 12) + | ((slow & 1) << 11) + | (x4_en << 10) + | (qd_en << 9) + | (unq_mrs_en << 8) + | ((obc_cfg & 0x1) << 6) + | ((ap_en & 0x1) << 5) + | ((d_init & 0x1) << 4) + | ((rcw_en & 0x1) << 2) + | ((md_en & 0x1) << 0) + ); + debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2); +} + +/* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ +static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + const unsigned int unq_mrs_en) +{ + unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ + unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */ + +#if defined(CONFIG_SYS_FSL_DDR3) + int i; + unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */ + unsigned int srt = 0; /* self-refresh temerature, normal range */ + unsigned int asr = 0; /* auto self-refresh disable */ + unsigned int cwl = compute_cas_write_latency() - 5; + unsigned int pasr = 0; /* partial array self refresh disable */ + + if (popts->rtt_override) + rtt_wr = popts->rtt_wr_override_value; + else + rtt_wr = popts->cs_local_opts[0].odt_rtt_wr; + + if (common_dimm->extended_op_srt) + srt = common_dimm->extended_op_srt; + + esdmode2 = (0 + | ((rtt_wr & 0x3) << 9) + | ((srt & 0x1) << 7) + | ((asr & 0x1) << 6) + | ((cwl & 0x7) << 3) + | ((pasr & 0x7) << 0)); +#endif + ddr->ddr_sdram_mode_2 = (0 + | ((esdmode2 & 0xFFFF) << 16) + | ((esdmode3 & 0xFFFF) << 0) + ); + debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2); + +#ifdef CONFIG_SYS_FSL_DDR3 + if (unq_mrs_en) { /* unique mode registers are supported */ + for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (popts->rtt_override) + rtt_wr = popts->rtt_wr_override_value; + else + rtt_wr = popts->cs_local_opts[i].odt_rtt_wr; + + esdmode2 &= 0xF9FF; /* clear bit 10, 9 */ + esdmode2 |= (rtt_wr & 0x3) << 9; + switch (i) { + case 1: + ddr->ddr_sdram_mode_4 = (0 + | ((esdmode2 & 0xFFFF) << 16) + | ((esdmode3 & 0xFFFF) << 0) + ); + break; + case 2: + ddr->ddr_sdram_mode_6 = (0 + | ((esdmode2 & 0xFFFF) << 16) + | ((esdmode3 & 0xFFFF) << 0) + ); + break; + case 3: + ddr->ddr_sdram_mode_8 = (0 + | ((esdmode2 & 0xFFFF) << 16) + | ((esdmode3 & 0xFFFF) << 0) + ); + break; + } + } + debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n", + ddr->ddr_sdram_mode_4); + debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n", + ddr->ddr_sdram_mode_6); + debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n", + ddr->ddr_sdram_mode_8); + } +#endif +} + +/* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */ +static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm) +{ + unsigned int refint; /* Refresh interval */ + unsigned int bstopre; /* Precharge interval */ + + refint = picos_to_mclk(common_dimm->refresh_rate_ps); + + bstopre = popts->bstopre; + + /* refint field used 0x3FFF in earlier controllers */ + ddr->ddr_sdram_interval = (0 + | ((refint & 0xFFFF) << 16) + | ((bstopre & 0x3FFF) << 0) + ); + debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval); +} + +#if defined(CONFIG_SYS_FSL_DDR3) +/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ +static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency, + const unsigned int unq_mrs_en) +{ + unsigned short esdmode; /* Extended SDRAM mode */ + unsigned short sdmode; /* SDRAM mode */ + + /* Mode Register - MR1 */ + unsigned int qoff = 0; /* Output buffer enable 0=yes, 1=no */ + unsigned int tdqs_en = 0; /* TDQS Enable: 0=no, 1=yes */ + unsigned int rtt; + unsigned int wrlvl_en = 0; /* Write level enable: 0=no, 1=yes */ + unsigned int al = 0; /* Posted CAS# additive latency (AL) */ + unsigned int dic = 0; /* Output driver impedance, 40ohm */ + unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), + 1=Disable (Test/Debug) */ + + /* Mode Register - MR0 */ + unsigned int dll_on; /* DLL control for precharge PD, 0=off, 1=on */ + unsigned int wr = 0; /* Write Recovery */ + unsigned int dll_rst; /* DLL Reset */ + unsigned int mode; /* Normal=0 or Test=1 */ + unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */ + /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */ + unsigned int bt; + unsigned int bl; /* BL: Burst Length */ + + unsigned int wr_mclk; + /* + * DDR_SDRAM_MODE doesn't support 9,11,13,15 + * Please refer JEDEC Standard No. 79-3E for Mode Register MR0 + * for this table + */ + static const u8 wr_table[] = {1, 2, 3, 4, 5, 5, 6, 6, 7, 7, 0, 0}; + + const unsigned int mclk_ps = get_memory_clk_period_ps(); + int i; + + if (popts->rtt_override) + rtt = popts->rtt_override_value; + else + rtt = popts->cs_local_opts[0].odt_rtt_norm; + + if (additive_latency == (cas_latency - 1)) + al = 1; + if (additive_latency == (cas_latency - 2)) + al = 2; + + if (popts->quad_rank_present) + dic = 1; /* output driver impedance 240/7 ohm */ + + /* + * The esdmode value will also be used for writing + * MR1 during write leveling for DDR3, although the + * bits specifically related to the write leveling + * scheme will be handled automatically by the DDR + * controller. so we set the wrlvl_en = 0 here. + */ + esdmode = (0 + | ((qoff & 0x1) << 12) + | ((tdqs_en & 0x1) << 11) + | ((rtt & 0x4) << 7) /* rtt field is split */ + | ((wrlvl_en & 0x1) << 7) + | ((rtt & 0x2) << 5) /* rtt field is split */ + | ((dic & 0x2) << 4) /* DIC field is split */ + | ((al & 0x3) << 3) + | ((rtt & 0x1) << 2) /* rtt field is split */ + | ((dic & 0x1) << 1) /* DIC field is split */ + | ((dll_en & 0x1) << 0) + ); + + /* + * DLL control for precharge PD + * 0=slow exit DLL off (tXPDLL) + * 1=fast exit DLL on (tXP) + */ + dll_on = 1; + + wr_mclk = (common_dimm->twr_ps + mclk_ps - 1) / mclk_ps; + if (wr_mclk <= 16) { + wr = wr_table[wr_mclk - 5]; + } else { + printf("Error: unsupported write recovery for mode register " + "wr_mclk = %d\n", wr_mclk); + } + + dll_rst = 0; /* dll no reset */ + mode = 0; /* normal mode */ + + /* look up table to get the cas latency bits */ + if (cas_latency >= 5 && cas_latency <= 16) { + unsigned char cas_latency_table[] = { + 0x2, /* 5 clocks */ + 0x4, /* 6 clocks */ + 0x6, /* 7 clocks */ + 0x8, /* 8 clocks */ + 0xa, /* 9 clocks */ + 0xc, /* 10 clocks */ + 0xe, /* 11 clocks */ + 0x1, /* 12 clocks */ + 0x3, /* 13 clocks */ + 0x5, /* 14 clocks */ + 0x7, /* 15 clocks */ + 0x9, /* 16 clocks */ + }; + caslat = cas_latency_table[cas_latency - 5]; + } else { + printf("Error: unsupported cas latency for mode register\n"); + } + + bt = 0; /* Nibble sequential */ + + switch (popts->burst_length) { + case DDR_BL8: + bl = 0; + break; + case DDR_OTF: + bl = 1; + break; + case DDR_BC4: + bl = 2; + break; + default: + printf("Error: invalid burst length of %u specified. " + " Defaulting to on-the-fly BC4 or BL8 beats.\n", + popts->burst_length); + bl = 1; + break; + } + + sdmode = (0 + | ((dll_on & 0x1) << 12) + | ((wr & 0x7) << 9) + | ((dll_rst & 0x1) << 8) + | ((mode & 0x1) << 7) + | (((caslat >> 1) & 0x7) << 4) + | ((bt & 0x1) << 3) + | ((caslat & 1) << 2) + | ((bl & 0x3) << 0) + ); + + ddr->ddr_sdram_mode = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + + debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); + + if (unq_mrs_en) { /* unique mode registers are supported */ + for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (popts->rtt_override) + rtt = popts->rtt_override_value; + else + rtt = popts->cs_local_opts[i].odt_rtt_norm; + + esdmode &= 0xFDBB; /* clear bit 9,6,2 */ + esdmode |= (0 + | ((rtt & 0x4) << 7) /* rtt field is split */ + | ((rtt & 0x2) << 5) /* rtt field is split */ + | ((rtt & 0x1) << 2) /* rtt field is split */ + ); + switch (i) { + case 1: + ddr->ddr_sdram_mode_3 = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + break; + case 2: + ddr->ddr_sdram_mode_5 = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + break; + case 3: + ddr->ddr_sdram_mode_7 = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + break; + } + } + debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n", + ddr->ddr_sdram_mode_3); + debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", + ddr->ddr_sdram_mode_5); + debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", + ddr->ddr_sdram_mode_5); + } +} + +#else /* !CONFIG_SYS_FSL_DDR3 */ + +/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ +static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency, + const unsigned int unq_mrs_en) +{ + unsigned short esdmode; /* Extended SDRAM mode */ + unsigned short sdmode; /* SDRAM mode */ + + /* + * FIXME: This ought to be pre-calculated in a + * technology-specific routine, + * e.g. compute_DDR2_mode_register(), and then the + * sdmode and esdmode passed in as part of common_dimm. + */ + + /* Extended Mode Register */ + unsigned int mrs = 0; /* Mode Register Set */ + unsigned int outputs = 0; /* 0=Enabled, 1=Disabled */ + unsigned int rdqs_en = 0; /* RDQS Enable: 0=no, 1=yes */ + unsigned int dqs_en = 0; /* DQS# Enable: 0=enable, 1=disable */ + unsigned int ocd = 0; /* 0x0=OCD not supported, + 0x7=OCD default state */ + unsigned int rtt; + unsigned int al; /* Posted CAS# additive latency (AL) */ + unsigned int ods = 0; /* Output Drive Strength: + 0 = Full strength (18ohm) + 1 = Reduced strength (4ohm) */ + unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), + 1=Disable (Test/Debug) */ + + /* Mode Register (MR) */ + unsigned int mr; /* Mode Register Definition */ + unsigned int pd; /* Power-Down Mode */ + unsigned int wr; /* Write Recovery */ + unsigned int dll_res; /* DLL Reset */ + unsigned int mode; /* Normal=0 or Test=1 */ + unsigned int caslat = 0;/* CAS# latency */ + /* BT: Burst Type (0=Sequential, 1=Interleaved) */ + unsigned int bt; + unsigned int bl; /* BL: Burst Length */ + +#if defined(CONFIG_SYS_FSL_DDR2) + const unsigned int mclk_ps = get_memory_clk_period_ps(); +#endif + dqs_en = !popts->dqs_config; + rtt = fsl_ddr_get_rtt(); + + al = additive_latency; + + esdmode = (0 + | ((mrs & 0x3) << 14) + | ((outputs & 0x1) << 12) + | ((rdqs_en & 0x1) << 11) + | ((dqs_en & 0x1) << 10) + | ((ocd & 0x7) << 7) + | ((rtt & 0x2) << 5) /* rtt field is split */ + | ((al & 0x7) << 3) + | ((rtt & 0x1) << 2) /* rtt field is split */ + | ((ods & 0x1) << 1) + | ((dll_en & 0x1) << 0) + ); + + mr = 0; /* FIXME: CHECKME */ + + /* + * 0 = Fast Exit (Normal) + * 1 = Slow Exit (Low Power) + */ + pd = 0; + +#if defined(CONFIG_SYS_FSL_DDR1) + wr = 0; /* Historical */ +#elif defined(CONFIG_SYS_FSL_DDR2) + wr = (common_dimm->twr_ps + mclk_ps - 1) / mclk_ps - 1; +#endif + dll_res = 0; + mode = 0; + +#if defined(CONFIG_SYS_FSL_DDR1) + if (1 <= cas_latency && cas_latency <= 4) { + unsigned char mode_caslat_table[4] = { + 0x5, /* 1.5 clocks */ + 0x2, /* 2.0 clocks */ + 0x6, /* 2.5 clocks */ + 0x3 /* 3.0 clocks */ + }; + caslat = mode_caslat_table[cas_latency - 1]; + } else { + printf("Warning: unknown cas_latency %d\n", cas_latency); + } +#elif defined(CONFIG_SYS_FSL_DDR2) + caslat = cas_latency; +#endif + bt = 0; + + switch (popts->burst_length) { + case DDR_BL4: + bl = 2; + break; + case DDR_BL8: + bl = 3; + break; + default: + printf("Error: invalid burst length of %u specified. " + " Defaulting to 4 beats.\n", + popts->burst_length); + bl = 2; + break; + } + + sdmode = (0 + | ((mr & 0x3) << 14) + | ((pd & 0x1) << 12) + | ((wr & 0x7) << 9) + | ((dll_res & 0x1) << 8) + | ((mode & 0x1) << 7) + | ((caslat & 0x7) << 4) + | ((bt & 0x1) << 3) + | ((bl & 0x7) << 0) + ); + + ddr->ddr_sdram_mode = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); +} +#endif + +/* DDR SDRAM Data Initialization (DDR_DATA_INIT) */ +static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int init_value; /* Initialization value */ + +#ifdef CONFIG_MEM_INIT_VALUE + init_value = CONFIG_MEM_INIT_VALUE; +#else + init_value = 0xDEADBEEF; +#endif + ddr->ddr_data_init = init_value; +} + +/* + * DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL) + * The old controller on the 8540/60 doesn't have this register. + * Hope it's OK to set it (to 0) anyway. + */ +static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned int clk_adjust; /* Clock adjust */ + + clk_adjust = popts->clk_adjust; + ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23; + debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl); +} + +/* DDR Initialization Address (DDR_INIT_ADDR) */ +static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int init_addr = 0; /* Initialization address */ + + ddr->ddr_init_addr = init_addr; +} + +/* DDR Initialization Address (DDR_INIT_EXT_ADDR) */ +static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int uia = 0; /* Use initialization address */ + unsigned int init_ext_addr = 0; /* Initialization address */ + + ddr->ddr_init_ext_addr = (0 + | ((uia & 0x1) << 31) + | (init_ext_addr & 0xF) + ); +} + +/* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */ +static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned int rwt = 0; /* Read-to-write turnaround for same CS */ + unsigned int wrt = 0; /* Write-to-read turnaround for same CS */ + unsigned int rrt = 0; /* Read-to-read turnaround for same CS */ + unsigned int wwt = 0; /* Write-to-write turnaround for same CS */ + unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */ + +#if defined(CONFIG_SYS_FSL_DDR3) + if (popts->burst_length == DDR_BL8) { + /* We set BL/2 for fixed BL8 */ + rrt = 0; /* BL/2 clocks */ + wwt = 0; /* BL/2 clocks */ + } else { + /* We need to set BL/2 + 2 to BC4 and OTF */ + rrt = 2; /* BL/2 + 2 clocks */ + wwt = 2; /* BL/2 + 2 clocks */ + } + dll_lock = 1; /* tDLLK = 512 clocks from spec */ +#endif + ddr->timing_cfg_4 = (0 + | ((rwt & 0xf) << 28) + | ((wrt & 0xf) << 24) + | ((rrt & 0xf) << 20) + | ((wwt & 0xf) << 16) + | (dll_lock & 0x3) + ); + debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4); +} + +/* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */ +static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr, unsigned int cas_latency) +{ + unsigned int rodt_on = 0; /* Read to ODT on */ + unsigned int rodt_off = 0; /* Read to ODT off */ + unsigned int wodt_on = 0; /* Write to ODT on */ + unsigned int wodt_off = 0; /* Write to ODT off */ + +#if defined(CONFIG_SYS_FSL_DDR3) + /* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */ + rodt_on = cas_latency - ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1; + rodt_off = 4; /* 4 clocks */ + wodt_on = 1; /* 1 clocks */ + wodt_off = 4; /* 4 clocks */ +#endif + + ddr->timing_cfg_5 = (0 + | ((rodt_on & 0x1f) << 24) + | ((rodt_off & 0x7) << 20) + | ((wodt_on & 0x1f) << 12) + | ((wodt_off & 0x7) << 8) + ); + debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5); +} + +/* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */ +static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int zq_en) +{ + unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */ + /* Normal Operation Full Calibration Time (tZQoper) */ + unsigned int zqoper = 0; + /* Normal Operation Short Calibration Time (tZQCS) */ + unsigned int zqcs = 0; + + if (zq_en) { + zqinit = 9; /* 512 clocks */ + zqoper = 8; /* 256 clocks */ + zqcs = 6; /* 64 clocks */ + } + + ddr->ddr_zq_cntl = (0 + | ((zq_en & 0x1) << 31) + | ((zqinit & 0xF) << 24) + | ((zqoper & 0xF) << 16) + | ((zqcs & 0xF) << 8) + ); + debug("FSLDDR: zq_cntl = 0x%08x\n", ddr->ddr_zq_cntl); +} + +/* DDR Write Leveling Control (DDR_WRLVL_CNTL) */ +static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int wrlvl_en, + const memctl_options_t *popts) +{ + /* + * First DQS pulse rising edge after margining mode + * is programmed (tWL_MRD) + */ + unsigned int wrlvl_mrd = 0; + /* ODT delay after margining mode is programmed (tWL_ODTEN) */ + unsigned int wrlvl_odten = 0; + /* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */ + unsigned int wrlvl_dqsen = 0; + /* WRLVL_SMPL: Write leveling sample time */ + unsigned int wrlvl_smpl = 0; + /* WRLVL_WLR: Write leveling repeition time */ + unsigned int wrlvl_wlr = 0; + /* WRLVL_START: Write leveling start time */ + unsigned int wrlvl_start = 0; + + /* suggest enable write leveling for DDR3 due to fly-by topology */ + if (wrlvl_en) { + /* tWL_MRD min = 40 nCK, we set it 64 */ + wrlvl_mrd = 0x6; + /* tWL_ODTEN 128 */ + wrlvl_odten = 0x7; + /* tWL_DQSEN min = 25 nCK, we set it 32 */ + wrlvl_dqsen = 0x5; + /* + * Write leveling sample time at least need 6 clocks + * higher than tWLO to allow enough time for progagation + * delay and sampling the prime data bits. + */ + wrlvl_smpl = 0xf; + /* + * Write leveling repetition time + * at least tWLO + 6 clocks clocks + * we set it 64 + */ + wrlvl_wlr = 0x6; + /* + * Write leveling start time + * The value use for the DQS_ADJUST for the first sample + * when write leveling is enabled. It probably needs to be + * overriden per platform. + */ + wrlvl_start = 0x8; + /* + * Override the write leveling sample and start time + * according to specific board + */ + if (popts->wrlvl_override) { + wrlvl_smpl = popts->wrlvl_sample; + wrlvl_start = popts->wrlvl_start; + } + } + + ddr->ddr_wrlvl_cntl = (0 + | ((wrlvl_en & 0x1) << 31) + | ((wrlvl_mrd & 0x7) << 24) + | ((wrlvl_odten & 0x7) << 20) + | ((wrlvl_dqsen & 0x7) << 16) + | ((wrlvl_smpl & 0xf) << 12) + | ((wrlvl_wlr & 0x7) << 8) + | ((wrlvl_start & 0x1F) << 0) + ); + debug("FSLDDR: wrlvl_cntl = 0x%08x\n", ddr->ddr_wrlvl_cntl); + ddr->ddr_wrlvl_cntl_2 = popts->wrlvl_ctl_2; + debug("FSLDDR: wrlvl_cntl_2 = 0x%08x\n", ddr->ddr_wrlvl_cntl_2); + ddr->ddr_wrlvl_cntl_3 = popts->wrlvl_ctl_3; + debug("FSLDDR: wrlvl_cntl_3 = 0x%08x\n", ddr->ddr_wrlvl_cntl_3); + +} + +/* DDR Self Refresh Counter (DDR_SR_CNTR) */ +static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it) +{ + /* Self Refresh Idle Threshold */ + ddr->ddr_sr_cntr = (sr_it & 0xF) << 16; +} + +static void set_ddr_eor(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) +{ + if (popts->addr_hash) { + ddr->ddr_eor = 0x40000000; /* address hash enable */ + puts("Address hashing enabled.\n"); + } +} + +static void set_ddr_cdr1(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) +{ + ddr->ddr_cdr1 = popts->ddr_cdr1; + debug("FSLDDR: ddr_cdr1 = 0x%08x\n", ddr->ddr_cdr1); +} + +static void set_ddr_cdr2(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) +{ + ddr->ddr_cdr2 = popts->ddr_cdr2; + debug("FSLDDR: ddr_cdr2 = 0x%08x\n", ddr->ddr_cdr2); +} + +unsigned int +check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int res = 0; + + /* + * Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are + * not set at the same time. + */ + if (ddr->ddr_sdram_cfg & 0x10000000 + && ddr->ddr_sdram_cfg & 0x00008000) { + printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] " + " should not be set at the same time.\n"); + res++; + } + + return res; +} + +unsigned int +compute_fsl_memctl_config_regs(const memctl_options_t *popts, + fsl_ddr_cfg_regs_t *ddr, + const common_timing_params_t *common_dimm, + const dimm_params_t *dimm_params, + unsigned int dbw_cap_adj, + unsigned int size_only) +{ + unsigned int i; + unsigned int cas_latency; + unsigned int additive_latency; + unsigned int sr_it; + unsigned int zq_en; + unsigned int wrlvl_en; + unsigned int ip_rev = 0; + unsigned int unq_mrs_en = 0; + int cs_en = 1; + + memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t)); + + if (common_dimm == NULL) { + printf("Error: subset DIMM params struct null pointer\n"); + return 1; + } + + /* + * Process overrides first. + * + * FIXME: somehow add dereated caslat to this + */ + cas_latency = (popts->cas_latency_override) + ? popts->cas_latency_override_value + : common_dimm->lowest_common_SPD_caslat; + + additive_latency = (popts->additive_latency_override) + ? popts->additive_latency_override_value + : common_dimm->additive_latency; + + sr_it = (popts->auto_self_refresh_en) + ? popts->sr_it + : 0; + /* ZQ calibration */ + zq_en = (popts->zq_en) ? 1 : 0; + /* write leveling */ + wrlvl_en = (popts->wrlvl_en) ? 1 : 0; + + /* Chip Select Memory Bounds (CSn_BNDS) */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + unsigned long long ea, sa; + unsigned int cs_per_dimm + = CONFIG_CHIP_SELECTS_PER_CTRL / CONFIG_DIMM_SLOTS_PER_CTLR; + unsigned int dimm_number + = i / cs_per_dimm; + unsigned long long rank_density + = dimm_params[dimm_number].rank_density >> dbw_cap_adj; + + if (dimm_params[dimm_number].n_ranks == 0) { + debug("Skipping setup of CS%u " + "because n_ranks on DIMM %u is 0\n", i, dimm_number); + continue; + } + if (popts->memctl_interleaving) { + switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + break; + case FSL_DDR_CS0_CS1: + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + if (i > 1) + cs_en = 0; + break; + case FSL_DDR_CS2_CS3: + default: + if (i > 0) + cs_en = 0; + break; + } + sa = common_dimm->base_address; + ea = sa + common_dimm->total_mem - 1; + } else if (!popts->memctl_interleaving) { + /* + * If memory interleaving between controllers is NOT + * enabled, the starting address for each memory + * controller is distinct. However, because rank + * interleaving is enabled, the starting and ending + * addresses of the total memory on that memory + * controller needs to be programmed into its + * respective CS0_BNDS. + */ + switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + sa = common_dimm->base_address; + ea = sa + common_dimm->total_mem - 1; + break; + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + if ((i >= 2) && (dimm_number == 0)) { + sa = dimm_params[dimm_number].base_address + + 2 * rank_density; + ea = sa + 2 * rank_density - 1; + } else { + sa = dimm_params[dimm_number].base_address; + ea = sa + 2 * rank_density - 1; + } + break; + case FSL_DDR_CS0_CS1: + if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { + sa = dimm_params[dimm_number].base_address; + ea = sa + rank_density - 1; + if (i != 1) + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; + } else { + sa = 0; + ea = 0; + } + if (i == 0) + ea += rank_density; + break; + case FSL_DDR_CS2_CS3: + if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { + sa = dimm_params[dimm_number].base_address; + ea = sa + rank_density - 1; + if (i != 3) + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; + } else { + sa = 0; + ea = 0; + } + if (i == 2) + ea += (rank_density >> dbw_cap_adj); + break; + default: /* No bank(chip-select) interleaving */ + sa = dimm_params[dimm_number].base_address; + ea = sa + rank_density - 1; + if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; + } else { + sa = 0; + ea = 0; + } + break; + } + } + + sa >>= 24; + ea >>= 24; + + if (cs_en) { + ddr->cs[i].bnds = (0 + | ((sa & 0xffff) << 16) /* starting address */ + | ((ea & 0xffff) << 0) /* ending address */ + ); + } else { + /* setting bnds to 0xffffffff for inactive CS */ + ddr->cs[i].bnds = 0xffffffff; + } + + debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds); + set_csn_config(dimm_number, i, ddr, popts, dimm_params); + set_csn_config_2(i, ddr); + } + + /* + * In the case we only need to compute the ddr sdram size, we only need + * to set csn registers, so return from here. + */ + if (size_only) + return 0; + + set_ddr_eor(ddr, popts); + +#if !defined(CONFIG_SYS_FSL_DDR1) + set_timing_cfg_0(ddr, popts, dimm_params); +#endif + + set_timing_cfg_3(ddr, popts, common_dimm, cas_latency, + additive_latency); + set_timing_cfg_1(ddr, popts, common_dimm, cas_latency); + set_timing_cfg_2(ddr, popts, common_dimm, + cas_latency, additive_latency); + + set_ddr_cdr1(ddr, popts); + set_ddr_cdr2(ddr, popts); + set_ddr_sdram_cfg(ddr, popts, common_dimm); + ip_rev = fsl_ddr_get_version(); + if (ip_rev > 0x40400) + unq_mrs_en = 1; + + set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en); + set_ddr_sdram_mode(ddr, popts, common_dimm, + cas_latency, additive_latency, unq_mrs_en); + set_ddr_sdram_mode_2(ddr, popts, common_dimm, unq_mrs_en); + set_ddr_sdram_interval(ddr, popts, common_dimm); + set_ddr_data_init(ddr); + set_ddr_sdram_clk_cntl(ddr, popts); + set_ddr_init_addr(ddr); + set_ddr_init_ext_addr(ddr); + set_timing_cfg_4(ddr, popts); + set_timing_cfg_5(ddr, cas_latency); + + set_ddr_zq_cntl(ddr, zq_en); + set_ddr_wrlvl_cntl(ddr, wrlvl_en, popts); + + set_ddr_sr_cntr(ddr, sr_it); + + set_ddr_sdram_rcw(ddr, popts, common_dimm); + +#ifdef CONFIG_SYS_FSL_DDR_EMU + /* disble DDR training for emulator */ + ddr->debug[2] = 0x00000400; + ddr->debug[4] = 0xff800000; +#endif + return check_fsl_memctl_config_regs(ddr); +} diff --git a/drivers/ddr/fsl/ddr1_dimm_params.c b/drivers/ddr/fsl/ddr1_dimm_params.c new file mode 100644 index 000000000..7df27b90b --- /dev/null +++ b/drivers/ddr/fsl/ddr1_dimm_params.c @@ -0,0 +1,343 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> + +/* + * Calculate the Density of each Physical Rank. + * Returned size is in bytes. + * + * Study these table from Byte 31 of JEDEC SPD Spec. + * + * DDR I DDR II + * Bit Size Size + * --- ----- ------ + * 7 high 512MB 512MB + * 6 256MB 256MB + * 5 128MB 128MB + * 4 64MB 16GB + * 3 32MB 8GB + * 2 16MB 4GB + * 1 2GB 2GB + * 0 low 1GB 1GB + * + * Reorder Table to be linear by stripping the bottom + * 2 or 5 bits off and shifting them up to the top. + */ + +static unsigned long long +compute_ranksize(unsigned int mem_type, unsigned char row_dens) +{ + unsigned long long bsize; + + /* Bottom 2 bits up to the top. */ + bsize = ((row_dens >> 2) | ((row_dens & 3) << 6)); + bsize <<= 24ULL; + debug("DDR: DDR I rank density = 0x%16llx\n", bsize); + + return bsize; +} + +/* + * Convert a two-nibble BCD value into a cycle time. + * While the spec calls for nano-seconds, picos are returned. + * + * This implements the tables for bytes 9, 23 and 25 for both + * DDR I and II. No allowance for distinguishing the invalid + * fields absent for DDR I yet present in DDR II is made. + * (That is, cycle times of .25, .33, .66 and .75 ns are + * allowed for both DDR II and I.) + */ +static unsigned int +convert_bcd_tenths_to_cycle_time_ps(unsigned int spd_val) +{ + /* Table look up the lower nibble, allow DDR I & II. */ + unsigned int tenths_ps[16] = { + 0, + 100, + 200, + 300, + 400, + 500, + 600, + 700, + 800, + 900, + 250, /* This and the next 3 entries valid ... */ + 330, /* ... only for tCK calculations. */ + 660, + 750, + 0, /* undefined */ + 0 /* undefined */ + }; + + unsigned int whole_ns = (spd_val & 0xF0) >> 4; + unsigned int tenth_ns = spd_val & 0x0F; + unsigned int ps = whole_ns * 1000 + tenths_ps[tenth_ns]; + + return ps; +} + +static unsigned int +convert_bcd_hundredths_to_cycle_time_ps(unsigned int spd_val) +{ + unsigned int tenth_ns = (spd_val & 0xF0) >> 4; + unsigned int hundredth_ns = spd_val & 0x0F; + unsigned int ps = tenth_ns * 100 + hundredth_ns * 10; + + return ps; +} + +static unsigned int byte40_table_ps[8] = { + 0, + 250, + 330, + 500, + 660, + 750, + 0, /* supposed to be RFC, but not sure what that means */ + 0 /* Undefined */ +}; + +static unsigned int +compute_trfc_ps_from_spd(unsigned char trctrfc_ext, unsigned char trfc) +{ + unsigned int trfc_ps; + + trfc_ps = (((trctrfc_ext & 0x1) * 256) + trfc) * 1000 + + byte40_table_ps[(trctrfc_ext >> 1) & 0x7]; + + return trfc_ps; +} + +static unsigned int +compute_trc_ps_from_spd(unsigned char trctrfc_ext, unsigned char trc) +{ + unsigned int trc_ps; + + trc_ps = trc * 1000 + byte40_table_ps[(trctrfc_ext >> 4) & 0x7]; + + return trc_ps; +} + +/* + * tCKmax from DDR I SPD Byte 43 + * + * Bits 7:2 == whole ns + * Bits 1:0 == quarter ns + * 00 == 0.00 ns + * 01 == 0.25 ns + * 10 == 0.50 ns + * 11 == 0.75 ns + * + * Returns picoseconds. + */ +static unsigned int +compute_tckmax_from_spd_ps(unsigned int byte43) +{ + return (byte43 >> 2) * 1000 + (byte43 & 0x3) * 250; +} + +/* + * Determine Refresh Rate. Ignore self refresh bit on DDR I. + * Table from SPD Spec, Byte 12, converted to picoseconds and + * filled in with "default" normal values. + */ +static unsigned int +determine_refresh_rate_ps(const unsigned int spd_refresh) +{ + unsigned int refresh_time_ps[8] = { + 15625000, /* 0 Normal 1.00x */ + 3900000, /* 1 Reduced .25x */ + 7800000, /* 2 Extended .50x */ + 31300000, /* 3 Extended 2.00x */ + 62500000, /* 4 Extended 4.00x */ + 125000000, /* 5 Extended 8.00x */ + 15625000, /* 6 Normal 1.00x filler */ + 15625000, /* 7 Normal 1.00x filler */ + }; + + return refresh_time_ps[spd_refresh & 0x7]; +} + +/* + * The purpose of this function is to compute a suitable + * CAS latency given the DRAM clock period. The SPD only + * defines at most 3 CAS latencies. Typically the slower in + * frequency the DIMM runs at, the shorter its CAS latency can be. + * If the DIMM is operating at a sufficiently low frequency, + * it may be able to run at a CAS latency shorter than the + * shortest SPD-defined CAS latency. + * + * If a CAS latency is not found, 0 is returned. + * + * Do this by finding in the standard speed bin table the longest + * tCKmin that doesn't exceed the value of mclk_ps (tCK). + * + * An assumption made is that the SDRAM device allows the + * CL to be programmed for a value that is lower than those + * advertised by the SPD. This is not always the case, + * as those modes not defined in the SPD are optional. + * + * CAS latency de-rating based upon values JEDEC Standard No. 79-E + * Table 11. + * + * ordinal 2, ddr1_speed_bins[1] contains tCK for CL=2 + */ + /* CL2.0 CL2.5 CL3.0 */ +unsigned short ddr1_speed_bins[] = {0, 7500, 6000, 5000 }; + +unsigned int +compute_derated_DDR1_CAS_latency(unsigned int mclk_ps) +{ + const unsigned int num_speed_bins = ARRAY_SIZE(ddr1_speed_bins); + unsigned int lowest_tCKmin_found = 0; + unsigned int lowest_tCKmin_CL = 0; + unsigned int i; + + debug("mclk_ps = %u\n", mclk_ps); + + for (i = 0; i < num_speed_bins; i++) { + unsigned int x = ddr1_speed_bins[i]; + debug("i=%u, x = %u, lowest_tCKmin_found = %u\n", + i, x, lowest_tCKmin_found); + if (x && lowest_tCKmin_found <= x && x <= mclk_ps) { + lowest_tCKmin_found = x; + lowest_tCKmin_CL = i + 1; + } + } + + debug("lowest_tCKmin_CL = %u\n", lowest_tCKmin_CL); + + return lowest_tCKmin_CL; +} + +/* + * ddr_compute_dimm_parameters for DDR1 SPD + * + * Compute DIMM parameters based upon the SPD information in spd. + * Writes the results to the dimm_params_t structure pointed by pdimm. + * + * FIXME: use #define for the retvals + */ +unsigned int +ddr_compute_dimm_parameters(const ddr1_spd_eeprom_t *spd, + dimm_params_t *pdimm, + unsigned int dimm_number) +{ + unsigned int retval; + + if (spd->mem_type) { + if (spd->mem_type != SPD_MEMTYPE_DDR) { + printf("DIMM %u: is not a DDR1 SPD.\n", dimm_number); + return 1; + } + } else { + memset(pdimm, 0, sizeof(dimm_params_t)); + return 1; + } + + retval = ddr1_spd_check(spd); + if (retval) { + printf("DIMM %u: failed checksum\n", dimm_number); + return 2; + } + + /* + * The part name in ASCII in the SPD EEPROM is not null terminated. + * Guarantee null termination here by presetting all bytes to 0 + * and copying the part name in ASCII from the SPD onto it + */ + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, spd->mpart, sizeof(pdimm->mpart) - 1); + + /* DIMM organization parameters */ + pdimm->n_ranks = spd->nrows; + pdimm->rank_density = compute_ranksize(spd->mem_type, spd->bank_dens); + pdimm->capacity = pdimm->n_ranks * pdimm->rank_density; + pdimm->data_width = spd->dataw_lsb; + pdimm->primary_sdram_width = spd->primw; + pdimm->ec_sdram_width = spd->ecw; + + /* + * FIXME: Need to determine registered_dimm status. + * 1 == register buffered + * 0 == unbuffered + */ + pdimm->registered_dimm = 0; /* unbuffered */ + + /* SDRAM device parameters */ + pdimm->n_row_addr = spd->nrow_addr; + pdimm->n_col_addr = spd->ncol_addr; + pdimm->n_banks_per_sdram_device = spd->nbanks; + pdimm->edc_config = spd->config; + pdimm->burst_lengths_bitmask = spd->burstl; + pdimm->row_density = spd->bank_dens; + + /* + * Calculate the Maximum Data Rate based on the Minimum Cycle time. + * The SPD clk_cycle field (tCKmin) is measured in tenths of + * nanoseconds and represented as BCD. + */ + pdimm->tckmin_x_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle); + pdimm->tckmin_x_minus_1_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle2); + pdimm->tckmin_x_minus_2_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle3); + + pdimm->tckmax_ps = compute_tckmax_from_spd_ps(spd->tckmax); + + /* + * Compute CAS latencies defined by SPD + * The SPD caslat_x should have at least 1 and at most 3 bits set. + * + * If cas_lat after masking is 0, the __ilog2 function returns + * 255 into the variable. This behavior is abused once. + */ + pdimm->caslat_x = __ilog2(spd->cas_lat); + pdimm->caslat_x_minus_1 = __ilog2(spd->cas_lat + & ~(1 << pdimm->caslat_x)); + pdimm->caslat_x_minus_2 = __ilog2(spd->cas_lat + & ~(1 << pdimm->caslat_x) + & ~(1 << pdimm->caslat_x_minus_1)); + + /* Compute CAS latencies below that defined by SPD */ + pdimm->caslat_lowest_derated + = compute_derated_DDR1_CAS_latency(get_memory_clk_period_ps()); + + /* Compute timing parameters */ + pdimm->trcd_ps = spd->trcd * 250; + pdimm->trp_ps = spd->trp * 250; + pdimm->tras_ps = spd->tras * 1000; + + pdimm->twr_ps = mclk_to_picos(3); + pdimm->twtr_ps = mclk_to_picos(1); + pdimm->trfc_ps = compute_trfc_ps_from_spd(0, spd->trfc); + + pdimm->trrd_ps = spd->trrd * 250; + pdimm->trc_ps = compute_trc_ps_from_spd(0, spd->trc); + + pdimm->refresh_rate_ps = determine_refresh_rate_ps(spd->refresh); + + pdimm->tis_ps = convert_bcd_hundredths_to_cycle_time_ps(spd->ca_setup); + pdimm->tih_ps = convert_bcd_hundredths_to_cycle_time_ps(spd->ca_hold); + pdimm->tds_ps + = convert_bcd_hundredths_to_cycle_time_ps(spd->data_setup); + pdimm->tdh_ps + = convert_bcd_hundredths_to_cycle_time_ps(spd->data_hold); + + pdimm->trtp_ps = mclk_to_picos(2); /* By the book. */ + pdimm->tdqsq_max_ps = spd->tdqsq * 10; + pdimm->tqhs_ps = spd->tqhs * 10; + + return 0; +} diff --git a/drivers/ddr/fsl/ddr2_dimm_params.c b/drivers/ddr/fsl/ddr2_dimm_params.c new file mode 100644 index 000000000..d865df78a --- /dev/null +++ b/drivers/ddr/fsl/ddr2_dimm_params.c @@ -0,0 +1,342 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> +/* + * Calculate the Density of each Physical Rank. + * Returned size is in bytes. + * + * Study these table from Byte 31 of JEDEC SPD Spec. + * + * DDR I DDR II + * Bit Size Size + * --- ----- ------ + * 7 high 512MB 512MB + * 6 256MB 256MB + * 5 128MB 128MB + * 4 64MB 16GB + * 3 32MB 8GB + * 2 16MB 4GB + * 1 2GB 2GB + * 0 low 1GB 1GB + * + * Reorder Table to be linear by stripping the bottom + * 2 or 5 bits off and shifting them up to the top. + * + */ +static unsigned long long +compute_ranksize(unsigned int mem_type, unsigned char row_dens) +{ + unsigned long long bsize; + + /* Bottom 5 bits up to the top. */ + bsize = ((row_dens >> 5) | ((row_dens & 31) << 3)); + bsize <<= 27ULL; + debug("DDR: DDR II rank density = 0x%16llx\n", bsize); + + return bsize; +} + +/* + * Convert a two-nibble BCD value into a cycle time. + * While the spec calls for nano-seconds, picos are returned. + * + * This implements the tables for bytes 9, 23 and 25 for both + * DDR I and II. No allowance for distinguishing the invalid + * fields absent for DDR I yet present in DDR II is made. + * (That is, cycle times of .25, .33, .66 and .75 ns are + * allowed for both DDR II and I.) + */ +static unsigned int +convert_bcd_tenths_to_cycle_time_ps(unsigned int spd_val) +{ + /* Table look up the lower nibble, allow DDR I & II. */ + unsigned int tenths_ps[16] = { + 0, + 100, + 200, + 300, + 400, + 500, + 600, + 700, + 800, + 900, + 250, /* This and the next 3 entries valid ... */ + 330, /* ... only for tCK calculations. */ + 660, + 750, + 0, /* undefined */ + 0 /* undefined */ + }; + + unsigned int whole_ns = (spd_val & 0xF0) >> 4; + unsigned int tenth_ns = spd_val & 0x0F; + unsigned int ps = whole_ns * 1000 + tenths_ps[tenth_ns]; + + return ps; +} + +static unsigned int +convert_bcd_hundredths_to_cycle_time_ps(unsigned int spd_val) +{ + unsigned int tenth_ns = (spd_val & 0xF0) >> 4; + unsigned int hundredth_ns = spd_val & 0x0F; + unsigned int ps = tenth_ns * 100 + hundredth_ns * 10; + + return ps; +} + +static unsigned int byte40_table_ps[8] = { + 0, + 250, + 330, + 500, + 660, + 750, + 0, /* supposed to be RFC, but not sure what that means */ + 0 /* Undefined */ +}; + +static unsigned int +compute_trfc_ps_from_spd(unsigned char trctrfc_ext, unsigned char trfc) +{ + unsigned int trfc_ps; + + trfc_ps = (((trctrfc_ext & 0x1) * 256) + trfc) * 1000 + + byte40_table_ps[(trctrfc_ext >> 1) & 0x7]; + + return trfc_ps; +} + +static unsigned int +compute_trc_ps_from_spd(unsigned char trctrfc_ext, unsigned char trc) +{ + unsigned int trc_ps; + + trc_ps = trc * 1000 + byte40_table_ps[(trctrfc_ext >> 4) & 0x7]; + + return trc_ps; +} + +/* + * Determine Refresh Rate. Ignore self refresh bit on DDR I. + * Table from SPD Spec, Byte 12, converted to picoseconds and + * filled in with "default" normal values. + */ +static unsigned int +determine_refresh_rate_ps(const unsigned int spd_refresh) +{ + unsigned int refresh_time_ps[8] = { + 15625000, /* 0 Normal 1.00x */ + 3900000, /* 1 Reduced .25x */ + 7800000, /* 2 Extended .50x */ + 31300000, /* 3 Extended 2.00x */ + 62500000, /* 4 Extended 4.00x */ + 125000000, /* 5 Extended 8.00x */ + 15625000, /* 6 Normal 1.00x filler */ + 15625000, /* 7 Normal 1.00x filler */ + }; + + return refresh_time_ps[spd_refresh & 0x7]; +} + +/* + * The purpose of this function is to compute a suitable + * CAS latency given the DRAM clock period. The SPD only + * defines at most 3 CAS latencies. Typically the slower in + * frequency the DIMM runs at, the shorter its CAS latency can. + * be. If the DIMM is operating at a sufficiently low frequency, + * it may be able to run at a CAS latency shorter than the + * shortest SPD-defined CAS latency. + * + * If a CAS latency is not found, 0 is returned. + * + * Do this by finding in the standard speed bin table the longest + * tCKmin that doesn't exceed the value of mclk_ps (tCK). + * + * An assumption made is that the SDRAM device allows the + * CL to be programmed for a value that is lower than those + * advertised by the SPD. This is not always the case, + * as those modes not defined in the SPD are optional. + * + * CAS latency de-rating based upon values JEDEC Standard No. 79-2C + * Table 40, "DDR2 SDRAM stanadard speed bins and tCK, tRCD, tRP, tRAS, + * and tRC for corresponding bin" + * + * ordinal 2, ddr2_speed_bins[1] contains tCK for CL=3 + * Not certain if any good value exists for CL=2 + */ + /* CL2 CL3 CL4 CL5 CL6 CL7*/ +unsigned short ddr2_speed_bins[] = { 0, 5000, 3750, 3000, 2500, 1875 }; + +unsigned int +compute_derated_DDR2_CAS_latency(unsigned int mclk_ps) +{ + const unsigned int num_speed_bins = ARRAY_SIZE(ddr2_speed_bins); + unsigned int lowest_tCKmin_found = 0; + unsigned int lowest_tCKmin_CL = 0; + unsigned int i; + + debug("mclk_ps = %u\n", mclk_ps); + + for (i = 0; i < num_speed_bins; i++) { + unsigned int x = ddr2_speed_bins[i]; + debug("i=%u, x = %u, lowest_tCKmin_found = %u\n", + i, x, lowest_tCKmin_found); + if (x && x <= mclk_ps && x >= lowest_tCKmin_found ) { + lowest_tCKmin_found = x; + lowest_tCKmin_CL = i + 2; + } + } + + debug("lowest_tCKmin_CL = %u\n", lowest_tCKmin_CL); + + return lowest_tCKmin_CL; +} + +/* + * ddr_compute_dimm_parameters for DDR2 SPD + * + * Compute DIMM parameters based upon the SPD information in spd. + * Writes the results to the dimm_params_t structure pointed by pdimm. + * + * FIXME: use #define for the retvals + */ +unsigned int +ddr_compute_dimm_parameters(const ddr2_spd_eeprom_t *spd, + dimm_params_t *pdimm, + unsigned int dimm_number) +{ + unsigned int retval; + + if (spd->mem_type) { + if (spd->mem_type != SPD_MEMTYPE_DDR2) { + printf("DIMM %u: is not a DDR2 SPD.\n", dimm_number); + return 1; + } + } else { + memset(pdimm, 0, sizeof(dimm_params_t)); + return 1; + } + + retval = ddr2_spd_check(spd); + if (retval) { + printf("DIMM %u: failed checksum\n", dimm_number); + return 2; + } + + /* + * The part name in ASCII in the SPD EEPROM is not null terminated. + * Guarantee null termination here by presetting all bytes to 0 + * and copying the part name in ASCII from the SPD onto it + */ + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, spd->mpart, sizeof(pdimm->mpart) - 1); + + /* DIMM organization parameters */ + pdimm->n_ranks = (spd->mod_ranks & 0x7) + 1; + pdimm->rank_density = compute_ranksize(spd->mem_type, spd->rank_dens); + pdimm->capacity = pdimm->n_ranks * pdimm->rank_density; + pdimm->data_width = spd->dataw; + pdimm->primary_sdram_width = spd->primw; + pdimm->ec_sdram_width = spd->ecw; + + /* These are all the types defined by the JEDEC DDR2 SPD 1.3 spec */ + switch (spd->dimm_type) { + case DDR2_SPD_DIMMTYPE_RDIMM: + case DDR2_SPD_DIMMTYPE_72B_SO_RDIMM: + case DDR2_SPD_DIMMTYPE_MINI_RDIMM: + /* Registered/buffered DIMMs */ + pdimm->registered_dimm = 1; + break; + + case DDR2_SPD_DIMMTYPE_UDIMM: + case DDR2_SPD_DIMMTYPE_SO_DIMM: + case DDR2_SPD_DIMMTYPE_MICRO_DIMM: + case DDR2_SPD_DIMMTYPE_MINI_UDIMM: + /* Unbuffered DIMMs */ + pdimm->registered_dimm = 0; + break; + + case DDR2_SPD_DIMMTYPE_72B_SO_CDIMM: + default: + printf("unknown dimm_type 0x%02X\n", spd->dimm_type); + return 1; + } + + /* SDRAM device parameters */ + pdimm->n_row_addr = spd->nrow_addr; + pdimm->n_col_addr = spd->ncol_addr; + pdimm->n_banks_per_sdram_device = spd->nbanks; + pdimm->edc_config = spd->config; + pdimm->burst_lengths_bitmask = spd->burstl; + pdimm->row_density = spd->rank_dens; + + /* + * Calculate the Maximum Data Rate based on the Minimum Cycle time. + * The SPD clk_cycle field (tCKmin) is measured in tenths of + * nanoseconds and represented as BCD. + */ + pdimm->tckmin_x_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle); + pdimm->tckmin_x_minus_1_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle2); + pdimm->tckmin_x_minus_2_ps + = convert_bcd_tenths_to_cycle_time_ps(spd->clk_cycle3); + + pdimm->tckmax_ps = convert_bcd_tenths_to_cycle_time_ps(spd->tckmax); + + /* + * Compute CAS latencies defined by SPD + * The SPD caslat_x should have at least 1 and at most 3 bits set. + * + * If cas_lat after masking is 0, the __ilog2 function returns + * 255 into the variable. This behavior is abused once. + */ + pdimm->caslat_x = __ilog2(spd->cas_lat); + pdimm->caslat_x_minus_1 = __ilog2(spd->cas_lat + & ~(1 << pdimm->caslat_x)); + pdimm->caslat_x_minus_2 = __ilog2(spd->cas_lat + & ~(1 << pdimm->caslat_x) + & ~(1 << pdimm->caslat_x_minus_1)); + + /* Compute CAS latencies below that defined by SPD */ + pdimm->caslat_lowest_derated + = compute_derated_DDR2_CAS_latency(get_memory_clk_period_ps()); + + /* Compute timing parameters */ + pdimm->trcd_ps = spd->trcd * 250; + pdimm->trp_ps = spd->trp * 250; + pdimm->tras_ps = spd->tras * 1000; + + pdimm->twr_ps = spd->twr * 250; + pdimm->twtr_ps = spd->twtr * 250; + pdimm->trfc_ps = compute_trfc_ps_from_spd(spd->trctrfc_ext, spd->trfc); + + pdimm->trrd_ps = spd->trrd * 250; + pdimm->trc_ps = compute_trc_ps_from_spd(spd->trctrfc_ext, spd->trc); + + pdimm->refresh_rate_ps = determine_refresh_rate_ps(spd->refresh); + + pdimm->tis_ps = convert_bcd_hundredths_to_cycle_time_ps(spd->ca_setup); + pdimm->tih_ps = convert_bcd_hundredths_to_cycle_time_ps(spd->ca_hold); + pdimm->tds_ps + = convert_bcd_hundredths_to_cycle_time_ps(spd->data_setup); + pdimm->tdh_ps + = convert_bcd_hundredths_to_cycle_time_ps(spd->data_hold); + + pdimm->trtp_ps = spd->trtp * 250; + pdimm->tdqsq_max_ps = spd->tdqsq * 10; + pdimm->tqhs_ps = spd->tqhs * 10; + + return 0; +} diff --git a/drivers/ddr/fsl/ddr3_dimm_params.c b/drivers/ddr/fsl/ddr3_dimm_params.c new file mode 100644 index 000000000..a4b8c101f --- /dev/null +++ b/drivers/ddr/fsl/ddr3_dimm_params.c @@ -0,0 +1,341 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * Dave Liu <daveliu@freescale.com> + * + * calculate the organization and timing parameter + * from ddr3 spd, please refer to the spec + * JEDEC standard No.21-C 4_01_02_11R18.pdf + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> + +/* + * Calculate the Density of each Physical Rank. + * Returned size is in bytes. + * + * each rank size = + * sdram capacity(bit) / 8 * primary bus width / sdram width + * + * where: sdram capacity = spd byte4[3:0] + * primary bus width = spd byte8[2:0] + * sdram width = spd byte7[2:0] + * + * SPD byte4 - sdram density and banks + * bit[3:0] size(bit) size(byte) + * 0000 256Mb 32MB + * 0001 512Mb 64MB + * 0010 1Gb 128MB + * 0011 2Gb 256MB + * 0100 4Gb 512MB + * 0101 8Gb 1GB + * 0110 16Gb 2GB + * + * SPD byte8 - module memory bus width + * bit[2:0] primary bus width + * 000 8bits + * 001 16bits + * 010 32bits + * 011 64bits + * + * SPD byte7 - module organiztion + * bit[2:0] sdram device width + * 000 4bits + * 001 8bits + * 010 16bits + * 011 32bits + * + */ +static unsigned long long +compute_ranksize(const ddr3_spd_eeprom_t *spd) +{ + unsigned long long bsize; + + int nbit_sdram_cap_bsize = 0; + int nbit_primary_bus_width = 0; + int nbit_sdram_width = 0; + + if ((spd->density_banks & 0xf) < 7) + nbit_sdram_cap_bsize = (spd->density_banks & 0xf) + 28; + if ((spd->bus_width & 0x7) < 4) + nbit_primary_bus_width = (spd->bus_width & 0x7) + 3; + if ((spd->organization & 0x7) < 4) + nbit_sdram_width = (spd->organization & 0x7) + 2; + + bsize = 1ULL << (nbit_sdram_cap_bsize - 3 + + nbit_primary_bus_width - nbit_sdram_width); + + debug("DDR: DDR III rank density = 0x%16llx\n", bsize); + + return bsize; +} + +/* + * ddr_compute_dimm_parameters for DDR3 SPD + * + * Compute DIMM parameters based upon the SPD information in spd. + * Writes the results to the dimm_params_t structure pointed by pdimm. + * + */ +unsigned int +ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, + dimm_params_t *pdimm, + unsigned int dimm_number) +{ + unsigned int retval; + unsigned int mtb_ps; + int ftb_10th_ps; + int i; + + if (spd->mem_type) { + if (spd->mem_type != SPD_MEMTYPE_DDR3) { + printf("DIMM %u: is not a DDR3 SPD.\n", dimm_number); + return 1; + } + } else { + memset(pdimm, 0, sizeof(dimm_params_t)); + return 1; + } + + retval = ddr3_spd_check(spd); + if (retval) { + printf("DIMM %u: failed checksum\n", dimm_number); + return 2; + } + + /* + * The part name in ASCII in the SPD EEPROM is not null terminated. + * Guarantee null termination here by presetting all bytes to 0 + * and copying the part name in ASCII from the SPD onto it + */ + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + if ((spd->info_size_crc & 0xF) > 1) + memcpy(pdimm->mpart, spd->mpart, sizeof(pdimm->mpart) - 1); + + /* DIMM organization parameters */ + pdimm->n_ranks = ((spd->organization >> 3) & 0x7) + 1; + pdimm->rank_density = compute_ranksize(spd); + pdimm->capacity = pdimm->n_ranks * pdimm->rank_density; + pdimm->primary_sdram_width = 1 << (3 + (spd->bus_width & 0x7)); + if ((spd->bus_width >> 3) & 0x3) + pdimm->ec_sdram_width = 8; + else + pdimm->ec_sdram_width = 0; + pdimm->data_width = pdimm->primary_sdram_width + + pdimm->ec_sdram_width; + pdimm->device_width = 1 << ((spd->organization & 0x7) + 2); + + /* These are the types defined by the JEDEC DDR3 SPD spec */ + pdimm->mirrored_dimm = 0; + pdimm->registered_dimm = 0; + switch (spd->module_type & DDR3_SPD_MODULETYPE_MASK) { + case DDR3_SPD_MODULETYPE_RDIMM: + case DDR3_SPD_MODULETYPE_MINI_RDIMM: + case DDR3_SPD_MODULETYPE_72B_SO_RDIMM: + /* Registered/buffered DIMMs */ + pdimm->registered_dimm = 1; + for (i = 0; i < 16; i += 2) { + u8 rcw = spd->mod_section.registered.rcw[i/2]; + pdimm->rcw[i] = (rcw >> 0) & 0x0F; + pdimm->rcw[i+1] = (rcw >> 4) & 0x0F; + } + break; + + case DDR3_SPD_MODULETYPE_UDIMM: + case DDR3_SPD_MODULETYPE_SO_DIMM: + case DDR3_SPD_MODULETYPE_MICRO_DIMM: + case DDR3_SPD_MODULETYPE_MINI_UDIMM: + case DDR3_SPD_MODULETYPE_MINI_CDIMM: + case DDR3_SPD_MODULETYPE_72B_SO_UDIMM: + case DDR3_SPD_MODULETYPE_72B_SO_CDIMM: + case DDR3_SPD_MODULETYPE_LRDIMM: + case DDR3_SPD_MODULETYPE_16B_SO_DIMM: + case DDR3_SPD_MODULETYPE_32B_SO_DIMM: + /* Unbuffered DIMMs */ + if (spd->mod_section.unbuffered.addr_mapping & 0x1) + pdimm->mirrored_dimm = 1; + break; + + default: + printf("unknown module_type 0x%02X\n", spd->module_type); + return 1; + } + + /* SDRAM device parameters */ + pdimm->n_row_addr = ((spd->addressing >> 3) & 0x7) + 12; + pdimm->n_col_addr = (spd->addressing & 0x7) + 9; + pdimm->n_banks_per_sdram_device = 8 << ((spd->density_banks >> 4) & 0x7); + + /* + * The SPD spec has not the ECC bit, + * We consider the DIMM as ECC capability + * when the extension bus exist + */ + if (pdimm->ec_sdram_width) + pdimm->edc_config = 0x02; + else + pdimm->edc_config = 0x00; + + /* + * The SPD spec has not the burst length byte + * but DDR3 spec has nature BL8 and BC4, + * BL8 -bit3, BC4 -bit2 + */ + pdimm->burst_lengths_bitmask = 0x0c; + pdimm->row_density = __ilog2(pdimm->rank_density); + + /* MTB - medium timebase + * The unit in the SPD spec is ns, + * We convert it to ps. + * eg: MTB = 0.125ns (125ps) + */ + mtb_ps = (spd->mtb_dividend * 1000) /spd->mtb_divisor; + pdimm->mtb_ps = mtb_ps; + + /* + * FTB - fine timebase + * use 1/10th of ps as our unit to avoid floating point + * eg, 10 for 1ps, 25 for 2.5ps, 50 for 5ps + */ + ftb_10th_ps = + ((spd->ftb_div & 0xf0) >> 4) * 10 / (spd->ftb_div & 0x0f); + pdimm->ftb_10th_ps = ftb_10th_ps; + /* + * sdram minimum cycle time + * we assume the MTB is 0.125ns + * eg: + * tck_min=15 MTB (1.875ns) ->DDR3-1066 + * =12 MTB (1.5ns) ->DDR3-1333 + * =10 MTB (1.25ns) ->DDR3-1600 + */ + pdimm->tckmin_x_ps = spd->tck_min * mtb_ps + + (spd->fine_tck_min * ftb_10th_ps) / 10; + + /* + * CAS latency supported + * bit4 - CL4 + * bit5 - CL5 + * bit18 - CL18 + */ + pdimm->caslat_x = ((spd->caslat_msb << 8) | spd->caslat_lsb) << 4; + + /* + * min CAS latency time + * eg: taa_min = + * DDR3-800D 100 MTB (12.5ns) + * DDR3-1066F 105 MTB (13.125ns) + * DDR3-1333H 108 MTB (13.5ns) + * DDR3-1600H 90 MTB (11.25ns) + */ + pdimm->taa_ps = spd->taa_min * mtb_ps + + (spd->fine_taa_min * ftb_10th_ps) / 10; + + /* + * min write recovery time + * eg: + * twr_min = 120 MTB (15ns) -> all speed grades. + */ + pdimm->twr_ps = spd->twr_min * mtb_ps; + + /* + * min RAS to CAS delay time + * eg: trcd_min = + * DDR3-800 100 MTB (12.5ns) + * DDR3-1066F 105 MTB (13.125ns) + * DDR3-1333H 108 MTB (13.5ns) + * DDR3-1600H 90 MTB (11.25) + */ + pdimm->trcd_ps = spd->trcd_min * mtb_ps + + (spd->fine_trcd_min * ftb_10th_ps) / 10; + + /* + * min row active to row active delay time + * eg: trrd_min = + * DDR3-800(1KB page) 80 MTB (10ns) + * DDR3-1333(1KB page) 48 MTB (6ns) + */ + pdimm->trrd_ps = spd->trrd_min * mtb_ps; + + /* + * min row precharge delay time + * eg: trp_min = + * DDR3-800D 100 MTB (12.5ns) + * DDR3-1066F 105 MTB (13.125ns) + * DDR3-1333H 108 MTB (13.5ns) + * DDR3-1600H 90 MTB (11.25ns) + */ + pdimm->trp_ps = spd->trp_min * mtb_ps + + (spd->fine_trp_min * ftb_10th_ps) / 10; + + /* min active to precharge delay time + * eg: tRAS_min = + * DDR3-800D 300 MTB (37.5ns) + * DDR3-1066F 300 MTB (37.5ns) + * DDR3-1333H 288 MTB (36ns) + * DDR3-1600H 280 MTB (35ns) + */ + pdimm->tras_ps = (((spd->tras_trc_ext & 0xf) << 8) | spd->tras_min_lsb) + * mtb_ps; + /* + * min active to actice/refresh delay time + * eg: tRC_min = + * DDR3-800D 400 MTB (50ns) + * DDR3-1066F 405 MTB (50.625ns) + * DDR3-1333H 396 MTB (49.5ns) + * DDR3-1600H 370 MTB (46.25ns) + */ + pdimm->trc_ps = (((spd->tras_trc_ext & 0xf0) << 4) | spd->trc_min_lsb) + * mtb_ps + (spd->fine_trc_min * ftb_10th_ps) / 10; + /* + * min refresh recovery delay time + * eg: tRFC_min = + * 512Mb 720 MTB (90ns) + * 1Gb 880 MTB (110ns) + * 2Gb 1280 MTB (160ns) + */ + pdimm->trfc_ps = ((spd->trfc_min_msb << 8) | spd->trfc_min_lsb) + * mtb_ps; + /* + * min internal write to read command delay time + * eg: twtr_min = 40 MTB (7.5ns) - all speed bins. + * tWRT is at least 4 mclk independent of operating freq. + */ + pdimm->twtr_ps = spd->twtr_min * mtb_ps; + + /* + * min internal read to precharge command delay time + * eg: trtp_min = 40 MTB (7.5ns) - all speed bins. + * tRTP is at least 4 mclk independent of operating freq. + */ + pdimm->trtp_ps = spd->trtp_min * mtb_ps; + + /* + * Average periodic refresh interval + * tREFI = 7.8 us at normal temperature range + * = 3.9 us at ext temperature range + */ + pdimm->refresh_rate_ps = 7800000; + if ((spd->therm_ref_opt & 0x1) && !(spd->therm_ref_opt & 0x2)) { + pdimm->refresh_rate_ps = 3900000; + pdimm->extended_op_srt = 1; + } + + /* + * min four active window delay time + * eg: tfaw_min = + * DDR3-800(1KB page) 320 MTB (40ns) + * DDR3-1066(1KB page) 300 MTB (37.5ns) + * DDR3-1333(1KB page) 240 MTB (30ns) + * DDR3-1600(1KB page) 240 MTB (30ns) + */ + pdimm->tfaw_ps = (((spd->tfaw_msb & 0xf) << 8) | spd->tfaw_min) + * mtb_ps; + + return 0; +} diff --git a/drivers/ddr/fsl/interactive.c b/drivers/ddr/fsl/interactive.c new file mode 100644 index 000000000..ebf3ed6f3 --- /dev/null +++ b/drivers/ddr/fsl/interactive.c @@ -0,0 +1,1871 @@ +/* + * Copyright 2010-2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. + * Based on code from spd_sdram.c + * Author: James Yang [at freescale.com] + * York Sun [at freescale.com] + */ + +#include <common.h> +#include <linux/ctype.h> +#include <asm/types.h> +#include <asm/io.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr.h> + +/* Option parameter Structures */ +struct options_string { + const char *option_name; + size_t offset; + unsigned int size; + const char printhex; +}; + +static unsigned int picos_to_mhz(unsigned int picos) +{ + return 1000000 / picos; +} + +static void print_option_table(const struct options_string *table, + int table_size, + const void *base) +{ + unsigned int i; + unsigned int *ptr; + unsigned long long *ptr_l; + + for (i = 0; i < table_size; i++) { + switch (table[i].size) { + case 4: + ptr = (unsigned int *) (base + table[i].offset); + if (table[i].printhex) { + printf("%s = 0x%08X\n", + table[i].option_name, *ptr); + } else { + printf("%s = %u\n", + table[i].option_name, *ptr); + } + break; + case 8: + ptr_l = (unsigned long long *) (base + table[i].offset); + printf("%s = %llu\n", + table[i].option_name, *ptr_l); + break; + default: + printf("Unrecognized size!\n"); + break; + } + } +} + +static int handle_option_table(const struct options_string *table, + int table_size, + void *base, + const char *opt, + const char *val) +{ + unsigned int i; + unsigned int value, *ptr; + unsigned long long value_l, *ptr_l; + + for (i = 0; i < table_size; i++) { + if (strcmp(table[i].option_name, opt) != 0) + continue; + switch (table[i].size) { + case 4: + value = simple_strtoul(val, NULL, 0); + ptr = base + table[i].offset; + *ptr = value; + break; + case 8: + value_l = simple_strtoull(val, NULL, 0); + ptr_l = base + table[i].offset; + *ptr_l = value_l; + break; + default: + printf("Unrecognized size!\n"); + break; + } + return 1; + } + + return 0; +} + +static void fsl_ddr_generic_edit(void *pdata, + void *pend, + unsigned int element_size, + unsigned int element_num, + unsigned int value) +{ + char *pcdata = (char *)pdata; /* BIG ENDIAN ONLY */ + + pcdata += element_num * element_size; + if ((pcdata + element_size) > (char *) pend) { + printf("trying to write past end of data\n"); + return; + } + + switch (element_size) { + case 1: + __raw_writeb(value, pcdata); + break; + case 2: + __raw_writew(value, pcdata); + break; + case 4: + __raw_writel(value, pcdata); + break; + default: + printf("unexpected element size %u\n", element_size); + break; + } +} + +static void fsl_ddr_spd_edit(fsl_ddr_info_t *pinfo, + unsigned int ctrl_num, + unsigned int dimm_num, + unsigned int element_num, + unsigned int value) +{ + generic_spd_eeprom_t *pspd; + + pspd = &(pinfo->spd_installed_dimms[ctrl_num][dimm_num]); + fsl_ddr_generic_edit(pspd, pspd + 1, 1, element_num, value); +} + +#define COMMON_TIMING(x) {#x, offsetof(common_timing_params_t, x), \ + sizeof((common_timing_params_t *)0)->x, 0} + +static void lowest_common_dimm_parameters_edit(fsl_ddr_info_t *pinfo, + unsigned int ctrl_num, + const char *optname_str, + const char *value_str) +{ + common_timing_params_t *p = &pinfo->common_timing_params[ctrl_num]; + + static const struct options_string options[] = { + COMMON_TIMING(tckmin_x_ps), + COMMON_TIMING(tckmax_ps), + COMMON_TIMING(tckmax_max_ps), + COMMON_TIMING(trcd_ps), + COMMON_TIMING(trp_ps), + COMMON_TIMING(tras_ps), + COMMON_TIMING(twr_ps), + COMMON_TIMING(twtr_ps), + COMMON_TIMING(trfc_ps), + COMMON_TIMING(trrd_ps), + COMMON_TIMING(trc_ps), + COMMON_TIMING(refresh_rate_ps), + COMMON_TIMING(tis_ps), + COMMON_TIMING(tih_ps), + COMMON_TIMING(tds_ps), + COMMON_TIMING(tdh_ps), + COMMON_TIMING(trtp_ps), + COMMON_TIMING(tdqsq_max_ps), + COMMON_TIMING(tqhs_ps), + COMMON_TIMING(ndimms_present), + COMMON_TIMING(lowest_common_SPD_caslat), + COMMON_TIMING(highest_common_derated_caslat), + COMMON_TIMING(additive_latency), + COMMON_TIMING(all_dimms_burst_lengths_bitmask), + COMMON_TIMING(all_dimms_registered), + COMMON_TIMING(all_dimms_unbuffered), + COMMON_TIMING(all_dimms_ecc_capable), + COMMON_TIMING(total_mem), + COMMON_TIMING(base_address), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + if (handle_option_table(options, n_opts, p, optname_str, value_str)) + return; + + printf("Error: couldn't find option string %s\n", optname_str); +} + +#define DIMM_PARM(x) {#x, offsetof(dimm_params_t, x), \ + sizeof((dimm_params_t *)0)->x, 0} + +static void fsl_ddr_dimm_parameters_edit(fsl_ddr_info_t *pinfo, + unsigned int ctrl_num, + unsigned int dimm_num, + const char *optname_str, + const char *value_str) +{ + dimm_params_t *p = &(pinfo->dimm_params[ctrl_num][dimm_num]); + + static const struct options_string options[] = { + DIMM_PARM(n_ranks), + DIMM_PARM(data_width), + DIMM_PARM(primary_sdram_width), + DIMM_PARM(ec_sdram_width), + DIMM_PARM(registered_dimm), + DIMM_PARM(device_width), + + DIMM_PARM(n_row_addr), + DIMM_PARM(n_col_addr), + DIMM_PARM(edc_config), + DIMM_PARM(n_banks_per_sdram_device), + DIMM_PARM(burst_lengths_bitmask), + DIMM_PARM(row_density), + + DIMM_PARM(tckmin_x_ps), + DIMM_PARM(tckmin_x_minus_1_ps), + DIMM_PARM(tckmin_x_minus_2_ps), + DIMM_PARM(tckmax_ps), + + DIMM_PARM(caslat_x), + DIMM_PARM(caslat_x_minus_1), + DIMM_PARM(caslat_x_minus_2), + + DIMM_PARM(caslat_lowest_derated), + + DIMM_PARM(trcd_ps), + DIMM_PARM(trp_ps), + DIMM_PARM(tras_ps), + DIMM_PARM(twr_ps), + DIMM_PARM(twtr_ps), + DIMM_PARM(trfc_ps), + DIMM_PARM(trrd_ps), + DIMM_PARM(trc_ps), + DIMM_PARM(refresh_rate_ps), + + DIMM_PARM(tis_ps), + DIMM_PARM(tih_ps), + DIMM_PARM(tds_ps), + DIMM_PARM(tdh_ps), + DIMM_PARM(trtp_ps), + DIMM_PARM(tdqsq_max_ps), + DIMM_PARM(tqhs_ps), + + DIMM_PARM(rank_density), + DIMM_PARM(capacity), + DIMM_PARM(base_address), + }; + + static const unsigned int n_opts = ARRAY_SIZE(options); + + if (handle_option_table(options, n_opts, p, optname_str, value_str)) + return; + + printf("couldn't find option string %s\n", optname_str); +} + +static void print_dimm_parameters(const dimm_params_t *pdimm) +{ + static const struct options_string options[] = { + DIMM_PARM(n_ranks), + DIMM_PARM(data_width), + DIMM_PARM(primary_sdram_width), + DIMM_PARM(ec_sdram_width), + DIMM_PARM(registered_dimm), + DIMM_PARM(device_width), + + DIMM_PARM(n_row_addr), + DIMM_PARM(n_col_addr), + DIMM_PARM(edc_config), + DIMM_PARM(n_banks_per_sdram_device), + + DIMM_PARM(tckmin_x_ps), + DIMM_PARM(tckmin_x_minus_1_ps), + DIMM_PARM(tckmin_x_minus_2_ps), + DIMM_PARM(tckmax_ps), + + DIMM_PARM(caslat_x), + DIMM_PARM(taa_ps), + DIMM_PARM(caslat_x_minus_1), + DIMM_PARM(caslat_x_minus_2), + DIMM_PARM(caslat_lowest_derated), + + DIMM_PARM(trcd_ps), + DIMM_PARM(trp_ps), + DIMM_PARM(tras_ps), + DIMM_PARM(twr_ps), + DIMM_PARM(twtr_ps), + DIMM_PARM(trfc_ps), + DIMM_PARM(trrd_ps), + DIMM_PARM(trc_ps), + DIMM_PARM(refresh_rate_ps), + + DIMM_PARM(tis_ps), + DIMM_PARM(tih_ps), + DIMM_PARM(tds_ps), + DIMM_PARM(tdh_ps), + DIMM_PARM(trtp_ps), + DIMM_PARM(tdqsq_max_ps), + DIMM_PARM(tqhs_ps), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + if (pdimm->n_ranks == 0) { + printf("DIMM not present\n"); + return; + } + printf("DIMM organization parameters:\n"); + printf("module part name = %s\n", pdimm->mpart); + printf("rank_density = %llu bytes (%llu megabytes)\n", + pdimm->rank_density, pdimm->rank_density / 0x100000); + printf("capacity = %llu bytes (%llu megabytes)\n", + pdimm->capacity, pdimm->capacity / 0x100000); + printf("burst_lengths_bitmask = %02X\n", + pdimm->burst_lengths_bitmask); + printf("base_addresss = %llu (%08llX %08llX)\n", + pdimm->base_address, + (pdimm->base_address >> 32), + pdimm->base_address & 0xFFFFFFFF); + print_option_table(options, n_opts, pdimm); +} + +static void print_lowest_common_dimm_parameters( + const common_timing_params_t *plcd_dimm_params) +{ + static const struct options_string options[] = { + COMMON_TIMING(tckmax_max_ps), + COMMON_TIMING(trcd_ps), + COMMON_TIMING(trp_ps), + COMMON_TIMING(tras_ps), + COMMON_TIMING(twr_ps), + COMMON_TIMING(twtr_ps), + COMMON_TIMING(trfc_ps), + COMMON_TIMING(trrd_ps), + COMMON_TIMING(trc_ps), + COMMON_TIMING(refresh_rate_ps), + COMMON_TIMING(tis_ps), + COMMON_TIMING(tds_ps), + COMMON_TIMING(tdh_ps), + COMMON_TIMING(trtp_ps), + COMMON_TIMING(tdqsq_max_ps), + COMMON_TIMING(tqhs_ps), + COMMON_TIMING(lowest_common_SPD_caslat), + COMMON_TIMING(highest_common_derated_caslat), + COMMON_TIMING(additive_latency), + COMMON_TIMING(ndimms_present), + COMMON_TIMING(all_dimms_registered), + COMMON_TIMING(all_dimms_unbuffered), + COMMON_TIMING(all_dimms_ecc_capable), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + /* Clock frequencies */ + printf("tckmin_x_ps = %u (%u MHz)\n", + plcd_dimm_params->tckmin_x_ps, + picos_to_mhz(plcd_dimm_params->tckmin_x_ps)); + printf("tckmax_ps = %u (%u MHz)\n", + plcd_dimm_params->tckmax_ps, + picos_to_mhz(plcd_dimm_params->tckmax_ps)); + printf("all_dimms_burst_lengths_bitmask = %02X\n", + plcd_dimm_params->all_dimms_burst_lengths_bitmask); + + print_option_table(options, n_opts, plcd_dimm_params); + + printf("total_mem = %llu (%llu megabytes)\n", + plcd_dimm_params->total_mem, + plcd_dimm_params->total_mem / 0x100000); + printf("base_address = %llu (%llu megabytes)\n", + plcd_dimm_params->base_address, + plcd_dimm_params->base_address / 0x100000); +} + +#define CTRL_OPTIONS(x) {#x, offsetof(memctl_options_t, x), \ + sizeof((memctl_options_t *)0)->x, 0} +#define CTRL_OPTIONS_CS(x, y) {"cs" #x "_" #y, \ + offsetof(memctl_options_t, cs_local_opts[x].y), \ + sizeof((memctl_options_t *)0)->cs_local_opts[x].y, 0} + +static void fsl_ddr_options_edit(fsl_ddr_info_t *pinfo, + unsigned int ctl_num, + const char *optname_str, + const char *value_str) +{ + memctl_options_t *p = &(pinfo->memctl_opts[ctl_num]); + /* + * This array all on the stack and *computed* each time this + * function is rung. + */ + static const struct options_string options[] = { + CTRL_OPTIONS_CS(0, odt_rd_cfg), + CTRL_OPTIONS_CS(0, odt_wr_cfg), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CTRL_OPTIONS_CS(1, odt_rd_cfg), + CTRL_OPTIONS_CS(1, odt_wr_cfg), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(2, odt_rd_cfg), + CTRL_OPTIONS_CS(2, odt_wr_cfg), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(3, odt_rd_cfg), + CTRL_OPTIONS_CS(3, odt_wr_cfg), +#endif +#if defined(CONFIG_SYS_FSL_DDR3) + CTRL_OPTIONS_CS(0, odt_rtt_norm), + CTRL_OPTIONS_CS(0, odt_rtt_wr), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CTRL_OPTIONS_CS(1, odt_rtt_norm), + CTRL_OPTIONS_CS(1, odt_rtt_wr), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(2, odt_rtt_norm), + CTRL_OPTIONS_CS(2, odt_rtt_wr), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(3, odt_rtt_norm), + CTRL_OPTIONS_CS(3, odt_rtt_wr), +#endif +#endif + CTRL_OPTIONS(memctl_interleaving), + CTRL_OPTIONS(memctl_interleaving_mode), + CTRL_OPTIONS(ba_intlv_ctl), + CTRL_OPTIONS(ecc_mode), + CTRL_OPTIONS(ecc_init_using_memctl), + CTRL_OPTIONS(dqs_config), + CTRL_OPTIONS(self_refresh_in_sleep), + CTRL_OPTIONS(dynamic_power), + CTRL_OPTIONS(data_bus_width), + CTRL_OPTIONS(burst_length), + CTRL_OPTIONS(cas_latency_override), + CTRL_OPTIONS(cas_latency_override_value), + CTRL_OPTIONS(use_derated_caslat), + CTRL_OPTIONS(additive_latency_override), + CTRL_OPTIONS(additive_latency_override_value), + CTRL_OPTIONS(clk_adjust), + CTRL_OPTIONS(cpo_override), + CTRL_OPTIONS(write_data_delay), + CTRL_OPTIONS(half_strength_driver_enable), + + /* + * These can probably be changed to 2T_EN and 3T_EN + * (using a leading numerical character) without problem + */ + CTRL_OPTIONS(twot_en), + CTRL_OPTIONS(threet_en), + CTRL_OPTIONS(ap_en), + CTRL_OPTIONS(x4_en), + CTRL_OPTIONS(bstopre), + CTRL_OPTIONS(wrlvl_override), + CTRL_OPTIONS(wrlvl_sample), + CTRL_OPTIONS(wrlvl_start), + CTRL_OPTIONS(rcw_override), + CTRL_OPTIONS(rcw_1), + CTRL_OPTIONS(rcw_2), + CTRL_OPTIONS(ddr_cdr1), + CTRL_OPTIONS(ddr_cdr2), + CTRL_OPTIONS(tcke_clock_pulse_width_ps), + CTRL_OPTIONS(tfaw_window_four_activates_ps), + CTRL_OPTIONS(trwt_override), + CTRL_OPTIONS(trwt), + }; + + static const unsigned int n_opts = ARRAY_SIZE(options); + + if (handle_option_table(options, n_opts, p, + optname_str, value_str)) + return; + + printf("couldn't find option string %s\n", optname_str); +} + +#define CFG_REGS(x) {#x, offsetof(fsl_ddr_cfg_regs_t, x), \ + sizeof((fsl_ddr_cfg_regs_t *)0)->x, 1} +#define CFG_REGS_CS(x, y) {"cs" #x "_" #y, \ + offsetof(fsl_ddr_cfg_regs_t, cs[x].y), \ + sizeof((fsl_ddr_cfg_regs_t *)0)->cs[x].y, 1} + +static void print_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int i; + static const struct options_string options[] = { + CFG_REGS_CS(0, bnds), + CFG_REGS_CS(0, config), + CFG_REGS_CS(0, config_2), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CFG_REGS_CS(1, bnds), + CFG_REGS_CS(1, config), + CFG_REGS_CS(1, config_2), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CFG_REGS_CS(2, bnds), + CFG_REGS_CS(2, config), + CFG_REGS_CS(2, config_2), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CFG_REGS_CS(3, bnds), + CFG_REGS_CS(3, config), + CFG_REGS_CS(3, config_2), +#endif + CFG_REGS(timing_cfg_3), + CFG_REGS(timing_cfg_0), + CFG_REGS(timing_cfg_1), + CFG_REGS(timing_cfg_2), + CFG_REGS(ddr_sdram_cfg), + CFG_REGS(ddr_sdram_cfg_2), + CFG_REGS(ddr_sdram_mode), + CFG_REGS(ddr_sdram_mode_2), + CFG_REGS(ddr_sdram_mode_3), + CFG_REGS(ddr_sdram_mode_4), + CFG_REGS(ddr_sdram_mode_5), + CFG_REGS(ddr_sdram_mode_6), + CFG_REGS(ddr_sdram_mode_7), + CFG_REGS(ddr_sdram_mode_8), + CFG_REGS(ddr_sdram_interval), + CFG_REGS(ddr_data_init), + CFG_REGS(ddr_sdram_clk_cntl), + CFG_REGS(ddr_init_addr), + CFG_REGS(ddr_init_ext_addr), + CFG_REGS(timing_cfg_4), + CFG_REGS(timing_cfg_5), + CFG_REGS(ddr_zq_cntl), + CFG_REGS(ddr_wrlvl_cntl), + CFG_REGS(ddr_wrlvl_cntl_2), + CFG_REGS(ddr_wrlvl_cntl_3), + CFG_REGS(ddr_sr_cntr), + CFG_REGS(ddr_sdram_rcw_1), + CFG_REGS(ddr_sdram_rcw_2), + CFG_REGS(ddr_cdr1), + CFG_REGS(ddr_cdr2), + CFG_REGS(err_disable), + CFG_REGS(err_int_en), + CFG_REGS(ddr_eor), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + print_option_table(options, n_opts, ddr); + + for (i = 0; i < 32; i++) + printf("debug_%02d = 0x%08X\n", i+1, ddr->debug[i]); +} + +static void fsl_ddr_regs_edit(fsl_ddr_info_t *pinfo, + unsigned int ctrl_num, + const char *regname, + const char *value_str) +{ + unsigned int i; + fsl_ddr_cfg_regs_t *ddr; + char buf[20]; + static const struct options_string options[] = { + CFG_REGS_CS(0, bnds), + CFG_REGS_CS(0, config), + CFG_REGS_CS(0, config_2), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CFG_REGS_CS(1, bnds), + CFG_REGS_CS(1, config), + CFG_REGS_CS(1, config_2), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CFG_REGS_CS(2, bnds), + CFG_REGS_CS(2, config), + CFG_REGS_CS(2, config_2), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3) + CFG_REGS_CS(3, bnds), + CFG_REGS_CS(3, config), + CFG_REGS_CS(3, config_2), +#endif + CFG_REGS(timing_cfg_3), + CFG_REGS(timing_cfg_0), + CFG_REGS(timing_cfg_1), + CFG_REGS(timing_cfg_2), + CFG_REGS(ddr_sdram_cfg), + CFG_REGS(ddr_sdram_cfg_2), + CFG_REGS(ddr_sdram_mode), + CFG_REGS(ddr_sdram_mode_2), + CFG_REGS(ddr_sdram_mode_3), + CFG_REGS(ddr_sdram_mode_4), + CFG_REGS(ddr_sdram_mode_5), + CFG_REGS(ddr_sdram_mode_6), + CFG_REGS(ddr_sdram_mode_7), + CFG_REGS(ddr_sdram_mode_8), + CFG_REGS(ddr_sdram_interval), + CFG_REGS(ddr_data_init), + CFG_REGS(ddr_sdram_clk_cntl), + CFG_REGS(ddr_init_addr), + CFG_REGS(ddr_init_ext_addr), + CFG_REGS(timing_cfg_4), + CFG_REGS(timing_cfg_5), + CFG_REGS(ddr_zq_cntl), + CFG_REGS(ddr_wrlvl_cntl), + CFG_REGS(ddr_wrlvl_cntl_2), + CFG_REGS(ddr_wrlvl_cntl_3), + CFG_REGS(ddr_sr_cntr), + CFG_REGS(ddr_sdram_rcw_1), + CFG_REGS(ddr_sdram_rcw_2), + CFG_REGS(ddr_cdr1), + CFG_REGS(ddr_cdr2), + CFG_REGS(err_disable), + CFG_REGS(err_int_en), + CFG_REGS(ddr_sdram_rcw_2), + CFG_REGS(ddr_sdram_rcw_2), + CFG_REGS(ddr_eor), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + debug("fsl_ddr_regs_edit: ctrl_num = %u, " + "regname = %s, value = %s\n", + ctrl_num, regname, value_str); + if (ctrl_num > CONFIG_NUM_DDR_CONTROLLERS) + return; + + ddr = &(pinfo->fsl_ddr_config_reg[ctrl_num]); + + if (handle_option_table(options, n_opts, ddr, regname, value_str)) + return; + + for (i = 0; i < 32; i++) { + unsigned int value = simple_strtoul(value_str, NULL, 0); + sprintf(buf, "debug_%u", i + 1); + if (strcmp(buf, regname) == 0) { + ddr->debug[i] = value; + return; + } + } + printf("Error: couldn't find register string %s\n", regname); +} + +#define CTRL_OPTIONS_HEX(x) {#x, offsetof(memctl_options_t, x), \ + sizeof((memctl_options_t *)0)->x, 1} + +static void print_memctl_options(const memctl_options_t *popts) +{ + static const struct options_string options[] = { + CTRL_OPTIONS_CS(0, odt_rd_cfg), + CTRL_OPTIONS_CS(0, odt_wr_cfg), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CTRL_OPTIONS_CS(1, odt_rd_cfg), + CTRL_OPTIONS_CS(1, odt_wr_cfg), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(2, odt_rd_cfg), + CTRL_OPTIONS_CS(2, odt_wr_cfg), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3) + CTRL_OPTIONS_CS(3, odt_rd_cfg), + CTRL_OPTIONS_CS(3, odt_wr_cfg), +#endif +#if defined(CONFIG_SYS_FSL_DDR3) + CTRL_OPTIONS_CS(0, odt_rtt_norm), + CTRL_OPTIONS_CS(0, odt_rtt_wr), +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1) + CTRL_OPTIONS_CS(1, odt_rtt_norm), + CTRL_OPTIONS_CS(1, odt_rtt_wr), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2) + CTRL_OPTIONS_CS(2, odt_rtt_norm), + CTRL_OPTIONS_CS(2, odt_rtt_wr), +#endif +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3) + CTRL_OPTIONS_CS(3, odt_rtt_norm), + CTRL_OPTIONS_CS(3, odt_rtt_wr), +#endif +#endif + CTRL_OPTIONS(memctl_interleaving), + CTRL_OPTIONS(memctl_interleaving_mode), + CTRL_OPTIONS_HEX(ba_intlv_ctl), + CTRL_OPTIONS(ecc_mode), + CTRL_OPTIONS(ecc_init_using_memctl), + CTRL_OPTIONS(dqs_config), + CTRL_OPTIONS(self_refresh_in_sleep), + CTRL_OPTIONS(dynamic_power), + CTRL_OPTIONS(data_bus_width), + CTRL_OPTIONS(burst_length), + CTRL_OPTIONS(cas_latency_override), + CTRL_OPTIONS(cas_latency_override_value), + CTRL_OPTIONS(use_derated_caslat), + CTRL_OPTIONS(additive_latency_override), + CTRL_OPTIONS(additive_latency_override_value), + CTRL_OPTIONS(clk_adjust), + CTRL_OPTIONS(cpo_override), + CTRL_OPTIONS(write_data_delay), + CTRL_OPTIONS(half_strength_driver_enable), + /* + * These can probably be changed to 2T_EN and 3T_EN + * (using a leading numerical character) without problem + */ + CTRL_OPTIONS(twot_en), + CTRL_OPTIONS(threet_en), + CTRL_OPTIONS(registered_dimm_en), + CTRL_OPTIONS(ap_en), + CTRL_OPTIONS(x4_en), + CTRL_OPTIONS(bstopre), + CTRL_OPTIONS(wrlvl_override), + CTRL_OPTIONS(wrlvl_sample), + CTRL_OPTIONS(wrlvl_start), + CTRL_OPTIONS(rcw_override), + CTRL_OPTIONS(rcw_1), + CTRL_OPTIONS(rcw_2), + CTRL_OPTIONS_HEX(ddr_cdr1), + CTRL_OPTIONS_HEX(ddr_cdr2), + CTRL_OPTIONS(tcke_clock_pulse_width_ps), + CTRL_OPTIONS(tfaw_window_four_activates_ps), + CTRL_OPTIONS(trwt_override), + CTRL_OPTIONS(trwt), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + print_option_table(options, n_opts, popts); +} + +#ifdef CONFIG_SYS_FSL_DDR1 +void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd) +{ + unsigned int i; + + printf("%-3d : %02x %s\n", 0, spd->info_size, + " spd->info_size, * 0 # bytes written into serial memory *"); + printf("%-3d : %02x %s\n", 1, spd->chip_size, + " spd->chip_size, * 1 Total # bytes of SPD memory device *"); + printf("%-3d : %02x %s\n", 2, spd->mem_type, + " spd->mem_type, * 2 Fundamental memory type *"); + printf("%-3d : %02x %s\n", 3, spd->nrow_addr, + " spd->nrow_addr, * 3 # of Row Addresses on this assembly *"); + printf("%-3d : %02x %s\n", 4, spd->ncol_addr, + " spd->ncol_addr, * 4 # of Column Addrs on this assembly *"); + printf("%-3d : %02x %s\n", 5, spd->nrows, + " spd->nrows * 5 # of DIMM Banks *"); + printf("%-3d : %02x %s\n", 6, spd->dataw_lsb, + " spd->dataw_lsb, * 6 Data Width lsb of this assembly *"); + printf("%-3d : %02x %s\n", 7, spd->dataw_msb, + " spd->dataw_msb, * 7 Data Width msb of this assembly *"); + printf("%-3d : %02x %s\n", 8, spd->voltage, + " spd->voltage, * 8 Voltage intf std of this assembly *"); + printf("%-3d : %02x %s\n", 9, spd->clk_cycle, + " spd->clk_cycle, * 9 SDRAM Cycle time at CL=X *"); + printf("%-3d : %02x %s\n", 10, spd->clk_access, + " spd->clk_access, * 10 SDRAM Access from Clock at CL=X *"); + printf("%-3d : %02x %s\n", 11, spd->config, + " spd->config, * 11 DIMM Configuration type *"); + printf("%-3d : %02x %s\n", 12, spd->refresh, + " spd->refresh, * 12 Refresh Rate/Type *"); + printf("%-3d : %02x %s\n", 13, spd->primw, + " spd->primw, * 13 Primary SDRAM Width *"); + printf("%-3d : %02x %s\n", 14, spd->ecw, + " spd->ecw, * 14 Error Checking SDRAM width *"); + printf("%-3d : %02x %s\n", 15, spd->min_delay, + " spd->min_delay, * 15 Back to Back Random Access *"); + printf("%-3d : %02x %s\n", 16, spd->burstl, + " spd->burstl, * 16 Burst Lengths Supported *"); + printf("%-3d : %02x %s\n", 17, spd->nbanks, + " spd->nbanks, * 17 # of Banks on Each SDRAM Device *"); + printf("%-3d : %02x %s\n", 18, spd->cas_lat, + " spd->cas_lat, * 18 CAS# Latencies Supported *"); + printf("%-3d : %02x %s\n", 19, spd->cs_lat, + " spd->cs_lat, * 19 Chip Select Latency *"); + printf("%-3d : %02x %s\n", 20, spd->write_lat, + " spd->write_lat, * 20 Write Latency/Recovery *"); + printf("%-3d : %02x %s\n", 21, spd->mod_attr, + " spd->mod_attr, * 21 SDRAM Module Attributes *"); + printf("%-3d : %02x %s\n", 22, spd->dev_attr, + " spd->dev_attr, * 22 SDRAM Device Attributes *"); + printf("%-3d : %02x %s\n", 23, spd->clk_cycle2, + " spd->clk_cycle2, * 23 Min SDRAM Cycle time at CL=X-1 *"); + printf("%-3d : %02x %s\n", 24, spd->clk_access2, + " spd->clk_access2, * 24 SDRAM Access from Clock at CL=X-1 *"); + printf("%-3d : %02x %s\n", 25, spd->clk_cycle3, + " spd->clk_cycle3, * 25 Min SDRAM Cycle time at CL=X-2 *"); + printf("%-3d : %02x %s\n", 26, spd->clk_access3, + " spd->clk_access3, * 26 Max Access from Clock at CL=X-2 *"); + printf("%-3d : %02x %s\n", 27, spd->trp, + " spd->trp, * 27 Min Row Precharge Time (tRP)*"); + printf("%-3d : %02x %s\n", 28, spd->trrd, + " spd->trrd, * 28 Min Row Active to Row Active (tRRD) *"); + printf("%-3d : %02x %s\n", 29, spd->trcd, + " spd->trcd, * 29 Min RAS to CAS Delay (tRCD) *"); + printf("%-3d : %02x %s\n", 30, spd->tras, + " spd->tras, * 30 Minimum RAS Pulse Width (tRAS) *"); + printf("%-3d : %02x %s\n", 31, spd->bank_dens, + " spd->bank_dens, * 31 Density of each bank on module *"); + printf("%-3d : %02x %s\n", 32, spd->ca_setup, + " spd->ca_setup, * 32 Cmd + Addr signal input setup time *"); + printf("%-3d : %02x %s\n", 33, spd->ca_hold, + " spd->ca_hold, * 33 Cmd and Addr signal input hold time *"); + printf("%-3d : %02x %s\n", 34, spd->data_setup, + " spd->data_setup, * 34 Data signal input setup time *"); + printf("%-3d : %02x %s\n", 35, spd->data_hold, + " spd->data_hold, * 35 Data signal input hold time *"); + printf("%-3d : %02x %s\n", 36, spd->res_36_40[0], + " spd->res_36_40[0], * 36 Reserved / tWR *"); + printf("%-3d : %02x %s\n", 37, spd->res_36_40[1], + " spd->res_36_40[1], * 37 Reserved / tWTR *"); + printf("%-3d : %02x %s\n", 38, spd->res_36_40[2], + " spd->res_36_40[2], * 38 Reserved / tRTP *"); + printf("%-3d : %02x %s\n", 39, spd->res_36_40[3], + " spd->res_36_40[3], * 39 Reserved / mem_probe *"); + printf("%-3d : %02x %s\n", 40, spd->res_36_40[4], + " spd->res_36_40[4], * 40 Reserved / trc,trfc extensions *"); + printf("%-3d : %02x %s\n", 41, spd->trc, + " spd->trc, * 41 Min Active to Auto refresh time tRC *"); + printf("%-3d : %02x %s\n", 42, spd->trfc, + " spd->trfc, * 42 Min Auto to Active period tRFC *"); + printf("%-3d : %02x %s\n", 43, spd->tckmax, + " spd->tckmax, * 43 Max device cycle time tCKmax *"); + printf("%-3d : %02x %s\n", 44, spd->tdqsq, + " spd->tdqsq, * 44 Max DQS to DQ skew *"); + printf("%-3d : %02x %s\n", 45, spd->tqhs, + " spd->tqhs, * 45 Max Read DataHold skew tQHS *"); + printf("%-3d : %02x %s\n", 46, spd->res_46, + " spd->res_46, * 46 Reserved/ PLL Relock time *"); + printf("%-3d : %02x %s\n", 47, spd->dimm_height, + " spd->dimm_height * 47 SDRAM DIMM Height *"); + + printf("%-3d-%3d: ", 48, 61); + + for (i = 0; i < 14; i++) + printf("%02x", spd->res_48_61[i]); + + printf(" * 48-61 IDD in SPD and Reserved space *\n"); + + printf("%-3d : %02x %s\n", 62, spd->spd_rev, + " spd->spd_rev, * 62 SPD Data Revision Code *"); + printf("%-3d : %02x %s\n", 63, spd->cksum, + " spd->cksum, * 63 Checksum for bytes 0-62 *"); + printf("%-3d-%3d: ", 64, 71); + + for (i = 0; i < 8; i++) + printf("%02x", spd->mid[i]); + + printf("* 64 Mfr's JEDEC ID code per JEP-108E *\n"); + printf("%-3d : %02x %s\n", 72, spd->mloc, + " spd->mloc, * 72 Manufacturing Location *"); + + printf("%-3d-%3d: >>", 73, 90); + + for (i = 0; i < 18; i++) + printf("%c", spd->mpart[i]); + + printf("<<* 73 Manufacturer's Part Number *\n"); + + printf("%-3d-%3d: %02x %02x %s\n", 91, 92, spd->rev[0], spd->rev[1], + "* 91 Revision Code *"); + printf("%-3d-%3d: %02x %02x %s\n", 93, 94, spd->mdate[0], spd->mdate[1], + "* 93 Manufacturing Date *"); + printf("%-3d-%3d: ", 95, 98); + + for (i = 0; i < 4; i++) + printf("%02x", spd->sernum[i]); + + printf("* 95 Assembly Serial Number *\n"); + + printf("%-3d-%3d: ", 99, 127); + + for (i = 0; i < 27; i++) + printf("%02x", spd->mspec[i]); + + printf("* 99 Manufacturer Specific Data *\n"); +} +#endif + +#ifdef CONFIG_SYS_FSL_DDR2 +void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd) +{ + unsigned int i; + + printf("%-3d : %02x %s\n", 0, spd->info_size, + " spd->info_size, * 0 # bytes written into serial memory *"); + printf("%-3d : %02x %s\n", 1, spd->chip_size, + " spd->chip_size, * 1 Total # bytes of SPD memory device *"); + printf("%-3d : %02x %s\n", 2, spd->mem_type, + " spd->mem_type, * 2 Fundamental memory type *"); + printf("%-3d : %02x %s\n", 3, spd->nrow_addr, + " spd->nrow_addr, * 3 # of Row Addresses on this assembly *"); + printf("%-3d : %02x %s\n", 4, spd->ncol_addr, + " spd->ncol_addr, * 4 # of Column Addrs on this assembly *"); + printf("%-3d : %02x %s\n", 5, spd->mod_ranks, + " spd->mod_ranks * 5 # of Module Rows on this assembly *"); + printf("%-3d : %02x %s\n", 6, spd->dataw, + " spd->dataw, * 6 Data Width of this assembly *"); + printf("%-3d : %02x %s\n", 7, spd->res_7, + " spd->res_7, * 7 Reserved *"); + printf("%-3d : %02x %s\n", 8, spd->voltage, + " spd->voltage, * 8 Voltage intf std of this assembly *"); + printf("%-3d : %02x %s\n", 9, spd->clk_cycle, + " spd->clk_cycle, * 9 SDRAM Cycle time at CL=X *"); + printf("%-3d : %02x %s\n", 10, spd->clk_access, + " spd->clk_access, * 10 SDRAM Access from Clock at CL=X *"); + printf("%-3d : %02x %s\n", 11, spd->config, + " spd->config, * 11 DIMM Configuration type *"); + printf("%-3d : %02x %s\n", 12, spd->refresh, + " spd->refresh, * 12 Refresh Rate/Type *"); + printf("%-3d : %02x %s\n", 13, spd->primw, + " spd->primw, * 13 Primary SDRAM Width *"); + printf("%-3d : %02x %s\n", 14, spd->ecw, + " spd->ecw, * 14 Error Checking SDRAM width *"); + printf("%-3d : %02x %s\n", 15, spd->res_15, + " spd->res_15, * 15 Reserved *"); + printf("%-3d : %02x %s\n", 16, spd->burstl, + " spd->burstl, * 16 Burst Lengths Supported *"); + printf("%-3d : %02x %s\n", 17, spd->nbanks, + " spd->nbanks, * 17 # of Banks on Each SDRAM Device *"); + printf("%-3d : %02x %s\n", 18, spd->cas_lat, + " spd->cas_lat, * 18 CAS# Latencies Supported *"); + printf("%-3d : %02x %s\n", 19, spd->mech_char, + " spd->mech_char, * 19 Mechanical Characteristics *"); + printf("%-3d : %02x %s\n", 20, spd->dimm_type, + " spd->dimm_type, * 20 DIMM type *"); + printf("%-3d : %02x %s\n", 21, spd->mod_attr, + " spd->mod_attr, * 21 SDRAM Module Attributes *"); + printf("%-3d : %02x %s\n", 22, spd->dev_attr, + " spd->dev_attr, * 22 SDRAM Device Attributes *"); + printf("%-3d : %02x %s\n", 23, spd->clk_cycle2, + " spd->clk_cycle2, * 23 Min SDRAM Cycle time at CL=X-1 *"); + printf("%-3d : %02x %s\n", 24, spd->clk_access2, + " spd->clk_access2, * 24 SDRAM Access from Clock at CL=X-1 *"); + printf("%-3d : %02x %s\n", 25, spd->clk_cycle3, + " spd->clk_cycle3, * 25 Min SDRAM Cycle time at CL=X-2 *"); + printf("%-3d : %02x %s\n", 26, spd->clk_access3, + " spd->clk_access3, * 26 Max Access from Clock at CL=X-2 *"); + printf("%-3d : %02x %s\n", 27, spd->trp, + " spd->trp, * 27 Min Row Precharge Time (tRP)*"); + printf("%-3d : %02x %s\n", 28, spd->trrd, + " spd->trrd, * 28 Min Row Active to Row Active (tRRD) *"); + printf("%-3d : %02x %s\n", 29, spd->trcd, + " spd->trcd, * 29 Min RAS to CAS Delay (tRCD) *"); + printf("%-3d : %02x %s\n", 30, spd->tras, + " spd->tras, * 30 Minimum RAS Pulse Width (tRAS) *"); + printf("%-3d : %02x %s\n", 31, spd->rank_dens, + " spd->rank_dens, * 31 Density of each rank on module *"); + printf("%-3d : %02x %s\n", 32, spd->ca_setup, + " spd->ca_setup, * 32 Cmd + Addr signal input setup time *"); + printf("%-3d : %02x %s\n", 33, spd->ca_hold, + " spd->ca_hold, * 33 Cmd and Addr signal input hold time *"); + printf("%-3d : %02x %s\n", 34, spd->data_setup, + " spd->data_setup, * 34 Data signal input setup time *"); + printf("%-3d : %02x %s\n", 35, spd->data_hold, + " spd->data_hold, * 35 Data signal input hold time *"); + printf("%-3d : %02x %s\n", 36, spd->twr, + " spd->twr, * 36 Write Recovery time tWR *"); + printf("%-3d : %02x %s\n", 37, spd->twtr, + " spd->twtr, * 37 Int write to read delay tWTR *"); + printf("%-3d : %02x %s\n", 38, spd->trtp, + " spd->trtp, * 38 Int read to precharge delay tRTP *"); + printf("%-3d : %02x %s\n", 39, spd->mem_probe, + " spd->mem_probe, * 39 Mem analysis probe characteristics *"); + printf("%-3d : %02x %s\n", 40, spd->trctrfc_ext, + " spd->trctrfc_ext, * 40 Extensions to trc and trfc *"); + printf("%-3d : %02x %s\n", 41, spd->trc, + " spd->trc, * 41 Min Active to Auto refresh time tRC *"); + printf("%-3d : %02x %s\n", 42, spd->trfc, + " spd->trfc, * 42 Min Auto to Active period tRFC *"); + printf("%-3d : %02x %s\n", 43, spd->tckmax, + " spd->tckmax, * 43 Max device cycle time tCKmax *"); + printf("%-3d : %02x %s\n", 44, spd->tdqsq, + " spd->tdqsq, * 44 Max DQS to DQ skew *"); + printf("%-3d : %02x %s\n", 45, spd->tqhs, + " spd->tqhs, * 45 Max Read DataHold skew tQHS *"); + printf("%-3d : %02x %s\n", 46, spd->pll_relock, + " spd->pll_relock, * 46 PLL Relock time *"); + printf("%-3d : %02x %s\n", 47, spd->t_casemax, + " spd->t_casemax, * 47 t_casemax *"); + printf("%-3d : %02x %s\n", 48, spd->psi_ta_dram, + " spd->psi_ta_dram, * 48 Thermal Resistance of DRAM Package " + "from Top (Case) to Ambient (Psi T-A DRAM) *"); + printf("%-3d : %02x %s\n", 49, spd->dt0_mode, + " spd->dt0_mode, * 49 DRAM Case Temperature Rise from " + "Ambient due to Activate-Precharge/Mode Bits " + "(DT0/Mode Bits) *)"); + printf("%-3d : %02x %s\n", 50, spd->dt2n_dt2q, + " spd->dt2n_dt2q, * 50 DRAM Case Temperature Rise from " + "Ambient due to Precharge/Quiet Standby " + "(DT2N/DT2Q) *"); + printf("%-3d : %02x %s\n", 51, spd->dt2p, + " spd->dt2p, * 51 DRAM Case Temperature Rise from " + "Ambient due to Precharge Power-Down (DT2P) *"); + printf("%-3d : %02x %s\n", 52, spd->dt3n, + " spd->dt3n, * 52 DRAM Case Temperature Rise from " + "Ambient due to Active Standby (DT3N) *"); + printf("%-3d : %02x %s\n", 53, spd->dt3pfast, + " spd->dt3pfast, * 53 DRAM Case Temperature Rise from " + "Ambient due to Active Power-Down with Fast PDN Exit " + "(DT3Pfast) *"); + printf("%-3d : %02x %s\n", 54, spd->dt3pslow, + " spd->dt3pslow, * 54 DRAM Case Temperature Rise from " + "Ambient due to Active Power-Down with Slow PDN Exit " + "(DT3Pslow) *"); + printf("%-3d : %02x %s\n", 55, spd->dt4r_dt4r4w, + " spd->dt4r_dt4r4w, * 55 DRAM Case Temperature Rise from " + "Ambient due to Page Open Burst Read/DT4R4W Mode Bit " + "(DT4R/DT4R4W Mode Bit) *"); + printf("%-3d : %02x %s\n", 56, spd->dt5b, + " spd->dt5b, * 56 DRAM Case Temperature Rise from " + "Ambient due to Burst Refresh (DT5B) *"); + printf("%-3d : %02x %s\n", 57, spd->dt7, + " spd->dt7, * 57 DRAM Case Temperature Rise from " + "Ambient due to Bank Interleave Reads with " + "Auto-Precharge (DT7) *"); + printf("%-3d : %02x %s\n", 58, spd->psi_ta_pll, + " spd->psi_ta_pll, * 58 Thermal Resistance of PLL Package form" + " Top (Case) to Ambient (Psi T-A PLL) *"); + printf("%-3d : %02x %s\n", 59, spd->psi_ta_reg, + " spd->psi_ta_reg, * 59 Thermal Reisitance of Register Package" + " from Top (Case) to Ambient (Psi T-A Register) *"); + printf("%-3d : %02x %s\n", 60, spd->dtpllactive, + " spd->dtpllactive, * 60 PLL Case Temperature Rise from " + "Ambient due to PLL Active (DT PLL Active) *"); + printf("%-3d : %02x %s\n", 61, spd->dtregact, + " spd->dtregact, " + "* 61 Register Case Temperature Rise from Ambient due to " + "Register Active/Mode Bit (DT Register Active/Mode Bit) *"); + printf("%-3d : %02x %s\n", 62, spd->spd_rev, + " spd->spd_rev, * 62 SPD Data Revision Code *"); + printf("%-3d : %02x %s\n", 63, spd->cksum, + " spd->cksum, * 63 Checksum for bytes 0-62 *"); + + printf("%-3d-%3d: ", 64, 71); + + for (i = 0; i < 8; i++) + printf("%02x", spd->mid[i]); + + printf("* 64 Mfr's JEDEC ID code per JEP-108E *\n"); + + printf("%-3d : %02x %s\n", 72, spd->mloc, + " spd->mloc, * 72 Manufacturing Location *"); + + printf("%-3d-%3d: >>", 73, 90); + for (i = 0; i < 18; i++) + printf("%c", spd->mpart[i]); + + + printf("<<* 73 Manufacturer's Part Number *\n"); + + printf("%-3d-%3d: %02x %02x %s\n", 91, 92, spd->rev[0], spd->rev[1], + "* 91 Revision Code *"); + printf("%-3d-%3d: %02x %02x %s\n", 93, 94, spd->mdate[0], spd->mdate[1], + "* 93 Manufacturing Date *"); + printf("%-3d-%3d: ", 95, 98); + + for (i = 0; i < 4; i++) + printf("%02x", spd->sernum[i]); + + printf("* 95 Assembly Serial Number *\n"); + + printf("%-3d-%3d: ", 99, 127); + for (i = 0; i < 27; i++) + printf("%02x", spd->mspec[i]); + + + printf("* 99 Manufacturer Specific Data *\n"); +} +#endif + +#ifdef CONFIG_SYS_FSL_DDR3 +void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd) +{ + unsigned int i; + + /* General Section: Bytes 0-59 */ + +#define PRINT_NXS(x, y, z...) printf("%-3d : %02x " z "\n", x, (u8)y); +#define PRINT_NNXXS(n0, n1, x0, x1, s) \ + printf("%-3d-%3d: %02x %02x " s "\n", n0, n1, x0, x1); + + PRINT_NXS(0, spd->info_size_crc, + "info_size_crc bytes written into serial memory, " + "CRC coverage"); + PRINT_NXS(1, spd->spd_rev, + "spd_rev SPD Revision"); + PRINT_NXS(2, spd->mem_type, + "mem_type Key Byte / DRAM Device Type"); + PRINT_NXS(3, spd->module_type, + "module_type Key Byte / Module Type"); + PRINT_NXS(4, spd->density_banks, + "density_banks SDRAM Density and Banks"); + PRINT_NXS(5, spd->addressing, + "addressing SDRAM Addressing"); + PRINT_NXS(6, spd->module_vdd, + "module_vdd Module Nominal Voltage, VDD"); + PRINT_NXS(7, spd->organization, + "organization Module Organization"); + PRINT_NXS(8, spd->bus_width, + "bus_width Module Memory Bus Width"); + PRINT_NXS(9, spd->ftb_div, + "ftb_div Fine Timebase (FTB) Dividend / Divisor"); + PRINT_NXS(10, spd->mtb_dividend, + "mtb_dividend Medium Timebase (MTB) Dividend"); + PRINT_NXS(11, spd->mtb_divisor, + "mtb_divisor Medium Timebase (MTB) Divisor"); + PRINT_NXS(12, spd->tck_min, + "tck_min SDRAM Minimum Cycle Time"); + PRINT_NXS(13, spd->res_13, + "res_13 Reserved"); + PRINT_NXS(14, spd->caslat_lsb, + "caslat_lsb CAS Latencies Supported, LSB"); + PRINT_NXS(15, spd->caslat_msb, + "caslat_msb CAS Latencies Supported, MSB"); + PRINT_NXS(16, spd->taa_min, + "taa_min Min CAS Latency Time"); + PRINT_NXS(17, spd->twr_min, + "twr_min Min Write REcovery Time"); + PRINT_NXS(18, spd->trcd_min, + "trcd_min Min RAS# to CAS# Delay Time"); + PRINT_NXS(19, spd->trrd_min, + "trrd_min Min Row Active to Row Active Delay Time"); + PRINT_NXS(20, spd->trp_min, + "trp_min Min Row Precharge Delay Time"); + PRINT_NXS(21, spd->tras_trc_ext, + "tras_trc_ext Upper Nibbles for tRAS and tRC"); + PRINT_NXS(22, spd->tras_min_lsb, + "tras_min_lsb Min Active to Precharge Delay Time, LSB"); + PRINT_NXS(23, spd->trc_min_lsb, + "trc_min_lsb Min Active to Active/Refresh Delay Time, LSB"); + PRINT_NXS(24, spd->trfc_min_lsb, + "trfc_min_lsb Min Refresh Recovery Delay Time LSB"); + PRINT_NXS(25, spd->trfc_min_msb, + "trfc_min_msb Min Refresh Recovery Delay Time MSB"); + PRINT_NXS(26, spd->twtr_min, + "twtr_min Min Internal Write to Read Command Delay Time"); + PRINT_NXS(27, spd->trtp_min, + "trtp_min " + "Min Internal Read to Precharge Command Delay Time"); + PRINT_NXS(28, spd->tfaw_msb, + "tfaw_msb Upper Nibble for tFAW"); + PRINT_NXS(29, spd->tfaw_min, + "tfaw_min Min Four Activate Window Delay Time"); + PRINT_NXS(30, spd->opt_features, + "opt_features SDRAM Optional Features"); + PRINT_NXS(31, spd->therm_ref_opt, + "therm_ref_opt SDRAM Thermal and Refresh Opts"); + PRINT_NXS(32, spd->therm_sensor, + "therm_sensor SDRAM Thermal Sensor"); + PRINT_NXS(33, spd->device_type, + "device_type SDRAM Device Type"); + PRINT_NXS(34, spd->fine_tck_min, + "fine_tck_min Fine offset for tCKmin"); + PRINT_NXS(35, spd->fine_taa_min, + "fine_taa_min Fine offset for tAAmin"); + PRINT_NXS(36, spd->fine_trcd_min, + "fine_trcd_min Fine offset for tRCDmin"); + PRINT_NXS(37, spd->fine_trp_min, + "fine_trp_min Fine offset for tRPmin"); + PRINT_NXS(38, spd->fine_trc_min, + "fine_trc_min Fine offset for tRCmin"); + + printf("%-3d-%3d: ", 39, 59); /* Reserved, General Section */ + + for (i = 39; i <= 59; i++) + printf("%02x ", spd->res_39_59[i - 39]); + + puts("\n"); + + switch (spd->module_type) { + case 0x02: /* UDIMM */ + case 0x03: /* SO-DIMM */ + case 0x04: /* Micro-DIMM */ + case 0x06: /* Mini-UDIMM */ + PRINT_NXS(60, spd->mod_section.unbuffered.mod_height, + "mod_height (Unbuffered) Module Nominal Height"); + PRINT_NXS(61, spd->mod_section.unbuffered.mod_thickness, + "mod_thickness (Unbuffered) Module Maximum Thickness"); + PRINT_NXS(62, spd->mod_section.unbuffered.ref_raw_card, + "ref_raw_card (Unbuffered) Reference Raw Card Used"); + PRINT_NXS(63, spd->mod_section.unbuffered.addr_mapping, + "addr_mapping (Unbuffered) Address mapping from " + "Edge Connector to DRAM"); + break; + case 0x01: /* RDIMM */ + case 0x05: /* Mini-RDIMM */ + PRINT_NXS(60, spd->mod_section.registered.mod_height, + "mod_height (Registered) Module Nominal Height"); + PRINT_NXS(61, spd->mod_section.registered.mod_thickness, + "mod_thickness (Registered) Module Maximum Thickness"); + PRINT_NXS(62, spd->mod_section.registered.ref_raw_card, + "ref_raw_card (Registered) Reference Raw Card Used"); + PRINT_NXS(63, spd->mod_section.registered.modu_attr, + "modu_attr (Registered) DIMM Module Attributes"); + PRINT_NXS(64, spd->mod_section.registered.thermal, + "thermal (Registered) Thermal Heat " + "Spreader Solution"); + PRINT_NXS(65, spd->mod_section.registered.reg_id_lo, + "reg_id_lo (Registered) Register Manufacturer ID " + "Code, LSB"); + PRINT_NXS(66, spd->mod_section.registered.reg_id_hi, + "reg_id_hi (Registered) Register Manufacturer ID " + "Code, MSB"); + PRINT_NXS(67, spd->mod_section.registered.reg_rev, + "reg_rev (Registered) Register " + "Revision Number"); + PRINT_NXS(68, spd->mod_section.registered.reg_type, + "reg_type (Registered) Register Type"); + for (i = 69; i <= 76; i++) { + printf("%-3d : %02x rcw[%d]\n", i, + spd->mod_section.registered.rcw[i-69], i-69); + } + break; + default: + /* Module-specific Section, Unsupported Module Type */ + printf("%-3d-%3d: ", 60, 116); + + for (i = 60; i <= 116; i++) + printf("%02x", spd->mod_section.uc[i - 60]); + + break; + } + + /* Unique Module ID: Bytes 117-125 */ + PRINT_NXS(117, spd->mmid_lsb, "Module MfgID Code LSB - JEP-106"); + PRINT_NXS(118, spd->mmid_msb, "Module MfgID Code MSB - JEP-106"); + PRINT_NXS(119, spd->mloc, "Mfg Location"); + PRINT_NNXXS(120, 121, spd->mdate[0], spd->mdate[1], "Mfg Date"); + + printf("%-3d-%3d: ", 122, 125); + + for (i = 122; i <= 125; i++) + printf("%02x ", spd->sernum[i - 122]); + printf(" Module Serial Number\n"); + + /* CRC: Bytes 126-127 */ + PRINT_NNXXS(126, 127, spd->crc[0], spd->crc[1], " SPD CRC"); + + /* Other Manufacturer Fields and User Space: Bytes 128-255 */ + printf("%-3d-%3d: ", 128, 145); + for (i = 128; i <= 145; i++) + printf("%02x ", spd->mpart[i - 128]); + printf(" Mfg's Module Part Number\n"); + + PRINT_NNXXS(146, 147, spd->mrev[0], spd->mrev[1], + "Module Revision code"); + + PRINT_NXS(148, spd->dmid_lsb, "DRAM MfgID Code LSB - JEP-106"); + PRINT_NXS(149, spd->dmid_msb, "DRAM MfgID Code MSB - JEP-106"); + + printf("%-3d-%3d: ", 150, 175); + for (i = 150; i <= 175; i++) + printf("%02x ", spd->msd[i - 150]); + printf(" Mfg's Specific Data\n"); + + printf("%-3d-%3d: ", 176, 255); + for (i = 176; i <= 255; i++) + printf("%02x", spd->cust[i - 176]); + printf(" Mfg's Specific Data\n"); + +} +#endif + +static inline void generic_spd_dump(const generic_spd_eeprom_t *spd) +{ +#if defined(CONFIG_SYS_FSL_DDR1) + ddr1_spd_dump(spd); +#elif defined(CONFIG_SYS_FSL_DDR2) + ddr2_spd_dump(spd); +#elif defined(CONFIG_SYS_FSL_DDR3) + ddr3_spd_dump(spd); +#endif +} + +static void fsl_ddr_printinfo(const fsl_ddr_info_t *pinfo, + unsigned int ctrl_mask, + unsigned int dimm_mask, + unsigned int do_mask) +{ + unsigned int i, j, retval; + + /* STEP 1: DIMM SPD data */ + if (do_mask & STEP_GET_SPD) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + if (!(dimm_mask & (1 << j))) + continue; + + printf("SPD info: Controller=%u " + "DIMM=%u\n", i, j); + generic_spd_dump( + &(pinfo->spd_installed_dimms[i][j])); + printf("\n"); + } + printf("\n"); + } + printf("\n"); + } + + /* STEP 2: DIMM Parameters */ + if (do_mask & STEP_COMPUTE_DIMM_PARMS) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + if (!(dimm_mask & (1 << j))) + continue; + printf("DIMM parameters: Controller=%u " + "DIMM=%u\n", i, j); + print_dimm_parameters( + &(pinfo->dimm_params[i][j])); + printf("\n"); + } + printf("\n"); + } + printf("\n"); + } + + /* STEP 3: Common Parameters */ + if (do_mask & STEP_COMPUTE_COMMON_PARMS) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + printf("\"lowest common\" DIMM parameters: " + "Controller=%u\n", i); + print_lowest_common_dimm_parameters( + &pinfo->common_timing_params[i]); + printf("\n"); + } + printf("\n"); + } + + /* STEP 4: User Configuration Options */ + if (do_mask & STEP_GATHER_OPTS) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + printf("User Config Options: Controller=%u\n", i); + print_memctl_options(&pinfo->memctl_opts[i]); + printf("\n"); + } + printf("\n"); + } + + /* STEP 5: Address assignment */ + if (do_mask & STEP_ASSIGN_ADDRESSES) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + printf("Address Assignment: Controller=%u " + "DIMM=%u\n", i, j); + printf("Don't have this functionality yet\n"); + } + printf("\n"); + } + printf("\n"); + } + + /* STEP 6: computed controller register values */ + if (do_mask & STEP_COMPUTE_REGS) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (!(ctrl_mask & (1 << i))) + continue; + printf("Computed Register Values: Controller=%u\n", i); + print_fsl_memctl_config_regs( + &pinfo->fsl_ddr_config_reg[i]); + retval = check_fsl_memctl_config_regs( + &pinfo->fsl_ddr_config_reg[i]); + if (retval) { + printf("check_fsl_memctl_config_regs " + "result = %u\n", retval); + } + printf("\n"); + } + printf("\n"); + } +} + +struct data_strings { + const char *data_name; + unsigned int step_mask; + unsigned int dimm_number_required; +}; + +#define DATA_OPTIONS(name, step, dimm) {#name, step, dimm} + +static unsigned int fsl_ddr_parse_interactive_cmd( + char **argv, + int argc, + unsigned int *pstep_mask, + unsigned int *pctlr_mask, + unsigned int *pdimm_mask, + unsigned int *pdimm_number_required + ) { + + static const struct data_strings options[] = { + DATA_OPTIONS(spd, STEP_GET_SPD, 1), + DATA_OPTIONS(dimmparms, STEP_COMPUTE_DIMM_PARMS, 1), + DATA_OPTIONS(commonparms, STEP_COMPUTE_COMMON_PARMS, 0), + DATA_OPTIONS(opts, STEP_GATHER_OPTS, 0), + DATA_OPTIONS(addresses, STEP_ASSIGN_ADDRESSES, 0), + DATA_OPTIONS(regs, STEP_COMPUTE_REGS, 0), + }; + static const unsigned int n_opts = ARRAY_SIZE(options); + + unsigned int i, j; + unsigned int error = 0; + + for (i = 1; i < argc; i++) { + unsigned int matched = 0; + + for (j = 0; j < n_opts; j++) { + if (strcmp(options[j].data_name, argv[i]) != 0) + continue; + *pstep_mask |= options[j].step_mask; + *pdimm_number_required = + options[j].dimm_number_required; + matched = 1; + break; + } + + if (matched) + continue; + + if (argv[i][0] == 'c') { + char c = argv[i][1]; + if (isdigit(c)) + *pctlr_mask |= 1 << (c - '0'); + continue; + } + + if (argv[i][0] == 'd') { + char c = argv[i][1]; + if (isdigit(c)) + *pdimm_mask |= 1 << (c - '0'); + continue; + } + + printf("unknown arg %s\n", argv[i]); + *pstep_mask = 0; + error = 1; + break; + } + + return error; +} + +int fsl_ddr_interactive_env_var_exists(void) +{ + char buffer[CONFIG_SYS_CBSIZE]; + + if (getenv_f("ddr_interactive", buffer, CONFIG_SYS_CBSIZE) >= 0) + return 1; + + return 0; +} + +unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo, int var_is_set) +{ + unsigned long long ddrsize; + const char *prompt = "FSL DDR>"; + char buffer[CONFIG_SYS_CBSIZE]; + char buffer2[CONFIG_SYS_CBSIZE]; + char *p = NULL; + char *argv[CONFIG_SYS_MAXARGS + 1]; /* NULL terminated */ + int argc; + unsigned int next_step = STEP_GET_SPD; + const char *usage = { + "commands:\n" + "print print SPD and intermediate computed data\n" + "reset reboot machine\n" + "recompute reload SPD and options to default and recompute regs\n" + "edit modify spd, parameter, or option\n" + "compute recompute registers from current next_step to end\n" + "copy copy parameters\n" + "next_step shows current next_step\n" + "help this message\n" + "go program the memory controller and continue with u-boot\n" + }; + + if (var_is_set) { + if (getenv_f("ddr_interactive", buffer2, CONFIG_SYS_CBSIZE) > 0) { + p = buffer2; + } else { + var_is_set = 0; + } + } + + /* + * The strategy for next_step is that it points to the next + * step in the computation process that needs to be done. + */ + while (1) { + if (var_is_set) { + char *pend = strchr(p, ';'); + if (pend) { + /* found command separator, copy sub-command */ + *pend = '\0'; + strcpy(buffer, p); + p = pend + 1; + } else { + /* separator not found, copy whole string */ + strcpy(buffer, p); + p = NULL; + var_is_set = 0; + } + } else { + /* + * No need to worry for buffer overflow here in + * this function; readline() maxes out at CFG_CBSIZE + */ + readline_into_buffer(prompt, buffer, 0); + } + argc = parse_line(buffer, argv); + if (argc == 0) + continue; + + + if (strcmp(argv[0], "help") == 0) { + puts(usage); + continue; + } + + if (strcmp(argv[0], "next_step") == 0) { + printf("next_step = 0x%02X (%s)\n", + next_step, + step_to_string(next_step)); + continue; + } + + if (strcmp(argv[0], "copy") == 0) { + unsigned int error = 0; + unsigned int step_mask = 0; + unsigned int src_ctlr_mask = 0; + unsigned int src_dimm_mask = 0; + unsigned int dimm_number_required = 0; + unsigned int src_ctlr_num = 0; + unsigned int src_dimm_num = 0; + unsigned int dst_ctlr_num = -1; + unsigned int dst_dimm_num = -1; + unsigned int i, num_dest_parms; + + if (argc == 1) { + printf("copy <src c#> <src d#> <spd|dimmparms|commonparms|opts|addresses|regs> <dst c#> <dst d#>\n"); + continue; + } + + error = fsl_ddr_parse_interactive_cmd( + argv, argc, + &step_mask, + &src_ctlr_mask, + &src_dimm_mask, + &dimm_number_required + ); + + /* XXX: only dimm_number_required and step_mask will + be used by this function. Parse the controller and + DIMM number separately because it is easier. */ + + if (error) + continue; + + /* parse source destination controller / DIMM */ + + num_dest_parms = dimm_number_required ? 2 : 1; + + for (i = 0; i < argc; i++) { + if (argv[i][0] == 'c') { + char c = argv[i][1]; + if (isdigit(c)) { + src_ctlr_num = (c - '0'); + break; + } + } + } + + for (i = 0; i < argc; i++) { + if (argv[i][0] == 'd') { + char c = argv[i][1]; + if (isdigit(c)) { + src_dimm_num = (c - '0'); + break; + } + } + } + + /* parse destination controller / DIMM */ + + for (i = argc - 1; i >= argc - num_dest_parms; i--) { + if (argv[i][0] == 'c') { + char c = argv[i][1]; + if (isdigit(c)) { + dst_ctlr_num = (c - '0'); + break; + } + } + } + + for (i = argc - 1; i >= argc - num_dest_parms; i--) { + if (argv[i][0] == 'd') { + char c = argv[i][1]; + if (isdigit(c)) { + dst_dimm_num = (c - '0'); + break; + } + } + } + + /* TODO: validate inputs */ + + debug("src_ctlr_num = %u, src_dimm_num = %u, dst_ctlr_num = %u, dst_dimm_num = %u, step_mask = %x\n", + src_ctlr_num, src_dimm_num, dst_ctlr_num, dst_dimm_num, step_mask); + + + switch (step_mask) { + + case STEP_GET_SPD: + memcpy(&(pinfo->spd_installed_dimms[dst_ctlr_num][dst_dimm_num]), + &(pinfo->spd_installed_dimms[src_ctlr_num][src_dimm_num]), + sizeof(pinfo->spd_installed_dimms[0][0])); + break; + + case STEP_COMPUTE_DIMM_PARMS: + memcpy(&(pinfo->dimm_params[dst_ctlr_num][dst_dimm_num]), + &(pinfo->dimm_params[src_ctlr_num][src_dimm_num]), + sizeof(pinfo->dimm_params[0][0])); + break; + + case STEP_COMPUTE_COMMON_PARMS: + memcpy(&(pinfo->common_timing_params[dst_ctlr_num]), + &(pinfo->common_timing_params[src_ctlr_num]), + sizeof(pinfo->common_timing_params[0])); + break; + + case STEP_GATHER_OPTS: + memcpy(&(pinfo->memctl_opts[dst_ctlr_num]), + &(pinfo->memctl_opts[src_ctlr_num]), + sizeof(pinfo->memctl_opts[0])); + break; + + /* someday be able to have addresses to copy addresses... */ + + case STEP_COMPUTE_REGS: + memcpy(&(pinfo->fsl_ddr_config_reg[dst_ctlr_num]), + &(pinfo->fsl_ddr_config_reg[src_ctlr_num]), + sizeof(pinfo->memctl_opts[0])); + break; + + default: + printf("unexpected step_mask value\n"); + } + + continue; + + } + + if (strcmp(argv[0], "edit") == 0) { + unsigned int error = 0; + unsigned int step_mask = 0; + unsigned int ctlr_mask = 0; + unsigned int dimm_mask = 0; + char *p_element = NULL; + char *p_value = NULL; + unsigned int dimm_number_required = 0; + unsigned int ctrl_num; + unsigned int dimm_num; + + if (argc == 1) { + /* Only the element and value must be last */ + printf("edit <c#> <d#> " + "<spd|dimmparms|commonparms|opts|" + "addresses|regs> <element> <value>\n"); + printf("for spd, specify byte number for " + "element\n"); + continue; + } + + error = fsl_ddr_parse_interactive_cmd( + argv, argc - 2, + &step_mask, + &ctlr_mask, + &dimm_mask, + &dimm_number_required + ); + + if (error) + continue; + + + /* Check arguments */ + + /* ERROR: If no steps were found */ + if (step_mask == 0) { + printf("Error: No valid steps were specified " + "in argument.\n"); + continue; + } + + /* ERROR: If multiple steps were found */ + if (step_mask & (step_mask - 1)) { + printf("Error: Multiple steps specified in " + "argument.\n"); + continue; + } + + /* ERROR: Controller not specified */ + if (ctlr_mask == 0) { + printf("Error: controller number not " + "specified or no element and " + "value specified\n"); + continue; + } + + if (ctlr_mask & (ctlr_mask - 1)) { + printf("Error: multiple controllers " + "specified, %X\n", ctlr_mask); + continue; + } + + /* ERROR: DIMM number not specified */ + if (dimm_number_required && dimm_mask == 0) { + printf("Error: DIMM number number not " + "specified or no element and " + "value specified\n"); + continue; + } + + if (dimm_mask & (dimm_mask - 1)) { + printf("Error: multipled DIMMs specified\n"); + continue; + } + + p_element = argv[argc - 2]; + p_value = argv[argc - 1]; + + ctrl_num = __ilog2(ctlr_mask); + dimm_num = __ilog2(dimm_mask); + + switch (step_mask) { + case STEP_GET_SPD: + { + unsigned int element_num; + unsigned int value; + + element_num = simple_strtoul(p_element, + NULL, 0); + value = simple_strtoul(p_value, + NULL, 0); + fsl_ddr_spd_edit(pinfo, + ctrl_num, + dimm_num, + element_num, + value); + next_step = STEP_COMPUTE_DIMM_PARMS; + } + break; + + case STEP_COMPUTE_DIMM_PARMS: + fsl_ddr_dimm_parameters_edit( + pinfo, ctrl_num, dimm_num, + p_element, p_value); + next_step = STEP_COMPUTE_COMMON_PARMS; + break; + + case STEP_COMPUTE_COMMON_PARMS: + lowest_common_dimm_parameters_edit(pinfo, + ctrl_num, p_element, p_value); + next_step = STEP_GATHER_OPTS; + break; + + case STEP_GATHER_OPTS: + fsl_ddr_options_edit(pinfo, ctrl_num, + p_element, p_value); + next_step = STEP_ASSIGN_ADDRESSES; + break; + + case STEP_ASSIGN_ADDRESSES: + printf("editing of address assignment " + "not yet implemented\n"); + break; + + case STEP_COMPUTE_REGS: + { + fsl_ddr_regs_edit(pinfo, + ctrl_num, + p_element, + p_value); + next_step = STEP_PROGRAM_REGS; + } + break; + + default: + printf("programming error\n"); + while (1) + ; + break; + } + continue; + } + + if (strcmp(argv[0], "reset") == 0) { + /* + * Reboot machine. + * Args don't seem to matter because this + * doesn't return + */ + do_reset(NULL, 0, 0, NULL); + printf("Reset didn't work\n"); + } + + if (strcmp(argv[0], "recompute") == 0) { + /* + * Recalculate everything, starting with + * loading SPD EEPROM from DIMMs + */ + next_step = STEP_GET_SPD; + ddrsize = fsl_ddr_compute(pinfo, next_step, 0); + continue; + } + + if (strcmp(argv[0], "compute") == 0) { + /* + * Compute rest of steps starting at + * the current next_step/ + */ + ddrsize = fsl_ddr_compute(pinfo, next_step, 0); + continue; + } + + if (strcmp(argv[0], "print") == 0) { + unsigned int error = 0; + unsigned int step_mask = 0; + unsigned int ctlr_mask = 0; + unsigned int dimm_mask = 0; + unsigned int dimm_number_required = 0; + + if (argc == 1) { + printf("print [c<n>] [d<n>] [spd] [dimmparms] " + "[commonparms] [opts] [addresses] [regs]\n"); + continue; + } + + error = fsl_ddr_parse_interactive_cmd( + argv, argc, + &step_mask, + &ctlr_mask, + &dimm_mask, + &dimm_number_required + ); + + if (error) + continue; + + /* If no particular controller was found, print all */ + if (ctlr_mask == 0) + ctlr_mask = 0xFF; + + /* If no particular dimm was found, print all dimms. */ + if (dimm_mask == 0) + dimm_mask = 0xFF; + + /* If no steps were found, print all steps. */ + if (step_mask == 0) + step_mask = STEP_ALL; + + fsl_ddr_printinfo(pinfo, ctlr_mask, + dimm_mask, step_mask); + continue; + } + + if (strcmp(argv[0], "go") == 0) { + if (next_step) + ddrsize = fsl_ddr_compute(pinfo, next_step, 0); + break; + } + + printf("unknown command %s\n", argv[0]); + } + + debug("end of memory = %llu\n", (u64)ddrsize); + + return ddrsize; +} diff --git a/drivers/ddr/fsl/lc_common_dimm_params.c b/drivers/ddr/fsl/lc_common_dimm_params.c new file mode 100644 index 000000000..610318ad1 --- /dev/null +++ b/drivers/ddr/fsl/lc_common_dimm_params.c @@ -0,0 +1,526 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> + +#if defined(CONFIG_SYS_FSL_DDR3) +static unsigned int +compute_cas_latency_ddr3(const dimm_params_t *dimm_params, + common_timing_params_t *outpdimm, + unsigned int number_of_dimms) +{ + unsigned int i; + unsigned int taamin_ps = 0; + unsigned int tckmin_x_ps = 0; + unsigned int common_caslat; + unsigned int caslat_actual; + unsigned int retry = 16; + unsigned int tmp; + const unsigned int mclk_ps = get_memory_clk_period_ps(); + + /* compute the common CAS latency supported between slots */ + tmp = dimm_params[0].caslat_x; + for (i = 1; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks) + tmp &= dimm_params[i].caslat_x; + } + common_caslat = tmp; + + /* compute the max tAAmin tCKmin between slots */ + for (i = 0; i < number_of_dimms; i++) { + taamin_ps = max(taamin_ps, dimm_params[i].taa_ps); + tckmin_x_ps = max(tckmin_x_ps, dimm_params[i].tckmin_x_ps); + } + /* validate if the memory clk is in the range of dimms */ + if (mclk_ps < tckmin_x_ps) { + printf("DDR clock (MCLK cycle %u ps) is faster than " + "the slowest DIMM(s) (tCKmin %u ps) can support.\n", + mclk_ps, tckmin_x_ps); + } + /* determine the acutal cas latency */ + caslat_actual = (taamin_ps + mclk_ps - 1) / mclk_ps; + /* check if the dimms support the CAS latency */ + while (!(common_caslat & (1 << caslat_actual)) && retry > 0) { + caslat_actual++; + retry--; + } + /* once the caculation of caslat_actual is completed + * we must verify that this CAS latency value does not + * exceed tAAmax, which is 20 ns for all DDR3 speed grades + */ + if (caslat_actual * mclk_ps > 20000) { + printf("The choosen cas latency %d is too large\n", + caslat_actual); + } + outpdimm->lowest_common_SPD_caslat = caslat_actual; + + return 0; +} +#endif + +/* + * compute_lowest_common_dimm_parameters() + * + * Determine the worst-case DIMM timing parameters from the set of DIMMs + * whose parameters have been computed into the array pointed to + * by dimm_params. + */ +unsigned int +compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, + common_timing_params_t *outpdimm, + const unsigned int number_of_dimms) +{ + unsigned int i, j; + + unsigned int tckmin_x_ps = 0; + unsigned int tckmax_ps = 0xFFFFFFFF; + unsigned int tckmax_max_ps = 0; + unsigned int trcd_ps = 0; + unsigned int trp_ps = 0; + unsigned int tras_ps = 0; + unsigned int twr_ps = 0; + unsigned int twtr_ps = 0; + unsigned int trfc_ps = 0; + unsigned int trrd_ps = 0; + unsigned int trc_ps = 0; + unsigned int refresh_rate_ps = 0; + unsigned int extended_op_srt = 1; + unsigned int tis_ps = 0; + unsigned int tih_ps = 0; + unsigned int tds_ps = 0; + unsigned int tdh_ps = 0; + unsigned int trtp_ps = 0; + unsigned int tdqsq_max_ps = 0; + unsigned int tqhs_ps = 0; + + unsigned int temp1, temp2; + unsigned int additive_latency = 0; +#if !defined(CONFIG_SYS_FSL_DDR3) + const unsigned int mclk_ps = get_memory_clk_period_ps(); + unsigned int lowest_good_caslat; + unsigned int not_ok; + + debug("using mclk_ps = %u\n", mclk_ps); +#endif + + temp1 = 0; + for (i = 0; i < number_of_dimms; i++) { + /* + * If there are no ranks on this DIMM, + * it probably doesn't exist, so skip it. + */ + if (dimm_params[i].n_ranks == 0) { + temp1++; + continue; + } + if (dimm_params[i].n_ranks == 4 && i != 0) { + printf("Found Quad-rank DIMM in wrong bank, ignored." + " Software may not run as expected.\n"); + temp1++; + continue; + } + + /* + * check if quad-rank DIMM is plugged if + * CONFIG_CHIP_SELECT_QUAD_CAPABLE is not defined + * Only the board with proper design is capable + */ +#ifndef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + if (dimm_params[i].n_ranks == 4 && \ + CONFIG_CHIP_SELECTS_PER_CTRL/CONFIG_DIMM_SLOTS_PER_CTLR < 4) { + printf("Found Quad-rank DIMM, not able to support."); + temp1++; + continue; + } +#endif + /* + * Find minimum tckmax_ps to find fastest slow speed, + * i.e., this is the slowest the whole system can go. + */ + tckmax_ps = min(tckmax_ps, dimm_params[i].tckmax_ps); + + /* Either find maximum value to determine slowest + * speed, delay, time, period, etc */ + tckmin_x_ps = max(tckmin_x_ps, dimm_params[i].tckmin_x_ps); + tckmax_max_ps = max(tckmax_max_ps, dimm_params[i].tckmax_ps); + trcd_ps = max(trcd_ps, dimm_params[i].trcd_ps); + trp_ps = max(trp_ps, dimm_params[i].trp_ps); + tras_ps = max(tras_ps, dimm_params[i].tras_ps); + twr_ps = max(twr_ps, dimm_params[i].twr_ps); + twtr_ps = max(twtr_ps, dimm_params[i].twtr_ps); + trfc_ps = max(trfc_ps, dimm_params[i].trfc_ps); + trrd_ps = max(trrd_ps, dimm_params[i].trrd_ps); + trc_ps = max(trc_ps, dimm_params[i].trc_ps); + tis_ps = max(tis_ps, dimm_params[i].tis_ps); + tih_ps = max(tih_ps, dimm_params[i].tih_ps); + tds_ps = max(tds_ps, dimm_params[i].tds_ps); + tdh_ps = max(tdh_ps, dimm_params[i].tdh_ps); + trtp_ps = max(trtp_ps, dimm_params[i].trtp_ps); + tqhs_ps = max(tqhs_ps, dimm_params[i].tqhs_ps); + refresh_rate_ps = max(refresh_rate_ps, + dimm_params[i].refresh_rate_ps); + /* extended_op_srt is either 0 or 1, 0 having priority */ + extended_op_srt = min(extended_op_srt, + dimm_params[i].extended_op_srt); + + /* + * Find maximum tdqsq_max_ps to find slowest. + * + * FIXME: is finding the slowest value the correct + * strategy for this parameter? + */ + tdqsq_max_ps = max(tdqsq_max_ps, dimm_params[i].tdqsq_max_ps); + } + + outpdimm->ndimms_present = number_of_dimms - temp1; + + if (temp1 == number_of_dimms) { + debug("no dimms this memory controller\n"); + return 0; + } + + outpdimm->tckmin_x_ps = tckmin_x_ps; + outpdimm->tckmax_ps = tckmax_ps; + outpdimm->tckmax_max_ps = tckmax_max_ps; + outpdimm->trcd_ps = trcd_ps; + outpdimm->trp_ps = trp_ps; + outpdimm->tras_ps = tras_ps; + outpdimm->twr_ps = twr_ps; + outpdimm->twtr_ps = twtr_ps; + outpdimm->trfc_ps = trfc_ps; + outpdimm->trrd_ps = trrd_ps; + outpdimm->trc_ps = trc_ps; + outpdimm->refresh_rate_ps = refresh_rate_ps; + outpdimm->extended_op_srt = extended_op_srt; + outpdimm->tis_ps = tis_ps; + outpdimm->tih_ps = tih_ps; + outpdimm->tds_ps = tds_ps; + outpdimm->tdh_ps = tdh_ps; + outpdimm->trtp_ps = trtp_ps; + outpdimm->tdqsq_max_ps = tdqsq_max_ps; + outpdimm->tqhs_ps = tqhs_ps; + + /* Determine common burst length for all DIMMs. */ + temp1 = 0xff; + for (i = 0; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks) { + temp1 &= dimm_params[i].burst_lengths_bitmask; + } + } + outpdimm->all_dimms_burst_lengths_bitmask = temp1; + + /* Determine if all DIMMs registered buffered. */ + temp1 = temp2 = 0; + for (i = 0; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks) { + if (dimm_params[i].registered_dimm) { + temp1 = 1; +#ifndef CONFIG_SPL_BUILD + printf("Detected RDIMM %s\n", + dimm_params[i].mpart); +#endif + } else { + temp2 = 1; +#ifndef CONFIG_SPL_BUILD + printf("Detected UDIMM %s\n", + dimm_params[i].mpart); +#endif + } + } + } + + outpdimm->all_dimms_registered = 0; + outpdimm->all_dimms_unbuffered = 0; + if (temp1 && !temp2) { + outpdimm->all_dimms_registered = 1; + } else if (!temp1 && temp2) { + outpdimm->all_dimms_unbuffered = 1; + } else { + printf("ERROR: Mix of registered buffered and unbuffered " + "DIMMs detected!\n"); + } + + temp1 = 0; + if (outpdimm->all_dimms_registered) + for (j = 0; j < 16; j++) { + outpdimm->rcw[j] = dimm_params[0].rcw[j]; + for (i = 1; i < number_of_dimms; i++) { + if (!dimm_params[i].n_ranks) + continue; + if (dimm_params[i].rcw[j] != dimm_params[0].rcw[j]) { + temp1 = 1; + break; + } + } + } + + if (temp1 != 0) + printf("ERROR: Mix different RDIMM detected!\n"); + +#if defined(CONFIG_SYS_FSL_DDR3) + if (compute_cas_latency_ddr3(dimm_params, outpdimm, number_of_dimms)) + return 1; +#else + /* + * Compute a CAS latency suitable for all DIMMs + * + * Strategy for SPD-defined latencies: compute only + * CAS latency defined by all DIMMs. + */ + + /* + * Step 1: find CAS latency common to all DIMMs using bitwise + * operation. + */ + temp1 = 0xFF; + for (i = 0; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks) { + temp2 = 0; + temp2 |= 1 << dimm_params[i].caslat_x; + temp2 |= 1 << dimm_params[i].caslat_x_minus_1; + temp2 |= 1 << dimm_params[i].caslat_x_minus_2; + /* + * FIXME: If there was no entry for X-2 (X-1) in + * the SPD, then caslat_x_minus_2 + * (caslat_x_minus_1) contains either 255 or + * 0xFFFFFFFF because that's what the glorious + * __ilog2 function returns for an input of 0. + * On 32-bit PowerPC, left shift counts with bit + * 26 set (that the value of 255 or 0xFFFFFFFF + * will have), cause the destination register to + * be 0. That is why this works. + */ + temp1 &= temp2; + } + } + + /* + * Step 2: check each common CAS latency against tCK of each + * DIMM's SPD. + */ + lowest_good_caslat = 0; + temp2 = 0; + while (temp1) { + not_ok = 0; + temp2 = __ilog2(temp1); + debug("checking common caslat = %u\n", temp2); + + /* Check if this CAS latency will work on all DIMMs at tCK. */ + for (i = 0; i < number_of_dimms; i++) { + if (!dimm_params[i].n_ranks) { + continue; + } + if (dimm_params[i].caslat_x == temp2) { + if (mclk_ps >= dimm_params[i].tckmin_x_ps) { + debug("CL = %u ok on DIMM %u at tCK=%u" + " ps with its tCKmin_X_ps of %u\n", + temp2, i, mclk_ps, + dimm_params[i].tckmin_x_ps); + continue; + } else { + not_ok++; + } + } + + if (dimm_params[i].caslat_x_minus_1 == temp2) { + unsigned int tckmin_x_minus_1_ps + = dimm_params[i].tckmin_x_minus_1_ps; + if (mclk_ps >= tckmin_x_minus_1_ps) { + debug("CL = %u ok on DIMM %u at " + "tCK=%u ps with its " + "tckmin_x_minus_1_ps of %u\n", + temp2, i, mclk_ps, + tckmin_x_minus_1_ps); + continue; + } else { + not_ok++; + } + } + + if (dimm_params[i].caslat_x_minus_2 == temp2) { + unsigned int tckmin_x_minus_2_ps + = dimm_params[i].tckmin_x_minus_2_ps; + if (mclk_ps >= tckmin_x_minus_2_ps) { + debug("CL = %u ok on DIMM %u at " + "tCK=%u ps with its " + "tckmin_x_minus_2_ps of %u\n", + temp2, i, mclk_ps, + tckmin_x_minus_2_ps); + continue; + } else { + not_ok++; + } + } + } + + if (!not_ok) { + lowest_good_caslat = temp2; + } + + temp1 &= ~(1 << temp2); + } + + debug("lowest common SPD-defined CAS latency = %u\n", + lowest_good_caslat); + outpdimm->lowest_common_SPD_caslat = lowest_good_caslat; + + + /* + * Compute a common 'de-rated' CAS latency. + * + * The strategy here is to find the *highest* dereated cas latency + * with the assumption that all of the DIMMs will support a dereated + * CAS latency higher than or equal to their lowest dereated value. + */ + temp1 = 0; + for (i = 0; i < number_of_dimms; i++) { + temp1 = max(temp1, dimm_params[i].caslat_lowest_derated); + } + outpdimm->highest_common_derated_caslat = temp1; + debug("highest common dereated CAS latency = %u\n", temp1); +#endif /* #if defined(CONFIG_SYS_FSL_DDR3) */ + + /* Determine if all DIMMs ECC capable. */ + temp1 = 1; + for (i = 0; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks && + !(dimm_params[i].edc_config & EDC_ECC)) { + temp1 = 0; + break; + } + } + if (temp1) { + debug("all DIMMs ECC capable\n"); + } else { + debug("Warning: not all DIMMs ECC capable, cant enable ECC\n"); + } + outpdimm->all_dimms_ecc_capable = temp1; + +#ifndef CONFIG_SYS_FSL_DDR3 + /* FIXME: move to somewhere else to validate. */ + if (mclk_ps > tckmax_max_ps) { + printf("Warning: some of the installed DIMMs " + "can not operate this slowly.\n"); + return 1; + } +#endif + /* + * Compute additive latency. + * + * For DDR1, additive latency should be 0. + * + * For DDR2, with ODT enabled, use "a value" less than ACTTORW, + * which comes from Trcd, and also note that: + * add_lat + caslat must be >= 4 + * + * For DDR3, we use the AL=0 + * + * When to use additive latency for DDR2: + * + * I. Because you are using CL=3 and need to do ODT on writes and + * want functionality. + * 1. Are you going to use ODT? (Does your board not have + * additional termination circuitry for DQ, DQS, DQS_, + * DM, RDQS, RDQS_ for x4/x8 configs?) + * 2. If so, is your lowest supported CL going to be 3? + * 3. If so, then you must set AL=1 because + * + * WL >= 3 for ODT on writes + * RL = AL + CL + * WL = RL - 1 + * -> + * WL = AL + CL - 1 + * AL + CL - 1 >= 3 + * AL + CL >= 4 + * QED + * + * RL >= 3 for ODT on reads + * RL = AL + CL + * + * Since CL aren't usually less than 2, AL=0 is a minimum, + * so the WL-derived AL should be the -- FIXME? + * + * II. Because you are using auto-precharge globally and want to + * use additive latency (posted CAS) to get more bandwidth. + * 1. Are you going to use auto-precharge mode globally? + * + * Use addtivie latency and compute AL to be 1 cycle less than + * tRCD, i.e. the READ or WRITE command is in the cycle + * immediately following the ACTIVATE command.. + * + * III. Because you feel like it or want to do some sort of + * degraded-performance experiment. + * 1. Do you just want to use additive latency because you feel + * like it? + * + * Validation: AL is less than tRCD, and within the other + * read-to-precharge constraints. + */ + + additive_latency = 0; + +#if defined(CONFIG_SYS_FSL_DDR2) + if (lowest_good_caslat < 4) { + additive_latency = (picos_to_mclk(trcd_ps) > lowest_good_caslat) + ? picos_to_mclk(trcd_ps) - lowest_good_caslat : 0; + if (mclk_to_picos(additive_latency) > trcd_ps) { + additive_latency = picos_to_mclk(trcd_ps); + debug("setting additive_latency to %u because it was " + " greater than tRCD_ps\n", additive_latency); + } + } + +#elif defined(CONFIG_SYS_FSL_DDR3) + /* + * The system will not use the global auto-precharge mode. + * However, it uses the page mode, so we set AL=0 + */ + additive_latency = 0; +#endif + + /* + * Validate additive latency + * FIXME: move to somewhere else to validate + * + * AL <= tRCD(min) + */ + if (mclk_to_picos(additive_latency) > trcd_ps) { + printf("Error: invalid additive latency exceeds tRCD(min).\n"); + return 1; + } + + /* + * RL = CL + AL; RL >= 3 for ODT_RD_CFG to be enabled + * WL = RL - 1; WL >= 3 for ODT_WL_CFG to be enabled + * ADD_LAT (the register) must be set to a value less + * than ACTTORW if WL = 1, then AL must be set to 1 + * RD_TO_PRE (the register) must be set to a minimum + * tRTP + AL if AL is nonzero + */ + + /* + * Additive latency will be applied only if the memctl option to + * use it. + */ + outpdimm->additive_latency = additive_latency; + + debug("tCKmin_ps = %u\n", outpdimm->tckmin_x_ps); + debug("trcd_ps = %u\n", outpdimm->trcd_ps); + debug("trp_ps = %u\n", outpdimm->trp_ps); + debug("tras_ps = %u\n", outpdimm->tras_ps); + debug("twr_ps = %u\n", outpdimm->twr_ps); + debug("twtr_ps = %u\n", outpdimm->twtr_ps); + debug("trfc_ps = %u\n", outpdimm->trfc_ps); + debug("trrd_ps = %u\n", outpdimm->trrd_ps); + debug("trc_ps = %u\n", outpdimm->trc_ps); + + return 0; +} diff --git a/drivers/ddr/fsl/main.c b/drivers/ddr/fsl/main.c new file mode 100644 index 000000000..d0cd58925 --- /dev/null +++ b/drivers/ddr/fsl/main.c @@ -0,0 +1,724 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +/* + * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. + * Based on code from spd_sdram.c + * Author: James Yang [at freescale.com] + */ + +#include <common.h> +#include <i2c.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr.h> + +#ifdef CONFIG_PPC +#include <asm/fsl_law.h> + +void fsl_ddr_set_lawbar( + const common_timing_params_t *memctl_common_params, + unsigned int memctl_interleaved, + unsigned int ctrl_num); +#endif + +void fsl_ddr_set_intl3r(const unsigned int granule_size); +#if defined(SPD_EEPROM_ADDRESS) || \ + defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \ + defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4) +#if (CONFIG_NUM_DDR_CONTROLLERS == 1) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS, +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 1) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 2) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS2, /* controller 2 */ +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 2) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ + [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS2, /* controller 2 */ + [2][0] = SPD_EEPROM_ADDRESS3, /* controller 3 */ +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ + [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ + [2][0] = SPD_EEPROM_ADDRESS5, /* controller 3 */ + [2][1] = SPD_EEPROM_ADDRESS6, /* controller 3 */ +}; + +#endif + +static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) +{ + int ret; + + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); + + ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, + sizeof(generic_spd_eeprom_t)); + + if (ret) { + if (i2c_address == +#ifdef SPD_EEPROM_ADDRESS + SPD_EEPROM_ADDRESS +#elif defined(SPD_EEPROM_ADDRESS1) + SPD_EEPROM_ADDRESS1 +#endif + ) { + printf("DDR: failed to read SPD from address %u\n", + i2c_address); + } else { + debug("DDR: failed to read SPD from address %u\n", + i2c_address); + } + memset(spd, 0, sizeof(generic_spd_eeprom_t)); + } +} + +__attribute__((weak, alias("__get_spd"))) +void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address); + +void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + unsigned int i2c_address = 0; + + if (ctrl_num >= CONFIG_NUM_DDR_CONTROLLERS) { + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) { + i2c_address = spd_i2c_addr[ctrl_num][i]; + get_spd(&(ctrl_dimms_spd[i]), i2c_address); + } +} +#else +void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ +} +#endif /* SPD_EEPROM_ADDRESSx */ + +/* + * ASSUMPTIONS: + * - Same number of CONFIG_DIMM_SLOTS_PER_CTLR on each controller + * - Same memory data bus width on all controllers + * + * NOTES: + * + * The memory controller and associated documentation use confusing + * terminology when referring to the orgranization of DRAM. + * + * Here is a terminology translation table: + * + * memory controller/documention |industry |this code |signals + * -------------------------------|-----------|-----------|----------------- + * physical bank/bank |rank |rank |chip select (CS) + * logical bank/sub-bank |bank |bank |bank address (BA) + * page/row |row |page |row address + * ??? |column |column |column address + * + * The naming confusion is further exacerbated by the descriptions of the + * memory controller interleaving feature, where accesses are interleaved + * _BETWEEN_ two seperate memory controllers. This is configured only in + * CS0_CONFIG[INTLV_CTL] of each memory controller. + * + * memory controller documentation | number of chip selects + * | per memory controller supported + * --------------------------------|----------------------------------------- + * cache line interleaving | 1 (CS0 only) + * page interleaving | 1 (CS0 only) + * bank interleaving | 1 (CS0 only) + * superbank interleraving | depends on bank (chip select) + * | interleraving [rank interleaving] + * | mode used on every memory controller + * + * Even further confusing is the existence of the interleaving feature + * _WITHIN_ each memory controller. The feature is referred to in + * documentation as chip select interleaving or bank interleaving, + * although it is configured in the DDR_SDRAM_CFG field. + * + * Name of field | documentation name | this code + * -----------------------------|-----------------------|------------------ + * DDR_SDRAM_CFG[BA_INTLV_CTL] | Bank (chip select) | rank interleaving + * | interleaving + */ + +const char *step_string_tbl[] = { + "STEP_GET_SPD", + "STEP_COMPUTE_DIMM_PARMS", + "STEP_COMPUTE_COMMON_PARMS", + "STEP_GATHER_OPTS", + "STEP_ASSIGN_ADDRESSES", + "STEP_COMPUTE_REGS", + "STEP_PROGRAM_REGS", + "STEP_ALL" +}; + +const char * step_to_string(unsigned int step) { + + unsigned int s = __ilog2(step); + + if ((1 << s) != step) + return step_string_tbl[7]; + + return step_string_tbl[s]; +} + +static unsigned long long __step_assign_addresses(fsl_ddr_info_t *pinfo, + unsigned int dbw_cap_adj[]) +{ + int i, j; + unsigned long long total_mem, current_mem_base, total_ctlr_mem; + unsigned long long rank_density, ctlr_density = 0; + + /* + * If a reduced data width is requested, but the SPD + * specifies a physically wider device, adjust the + * computed dimm capacities accordingly before + * assigning addresses. + */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + unsigned int found = 0; + + switch (pinfo->memctl_opts[i].data_bus_width) { + case 2: + /* 16-bit */ + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + unsigned int dw; + if (!pinfo->dimm_params[i][j].n_ranks) + continue; + dw = pinfo->dimm_params[i][j].primary_sdram_width; + if ((dw == 72 || dw == 64)) { + dbw_cap_adj[i] = 2; + break; + } else if ((dw == 40 || dw == 32)) { + dbw_cap_adj[i] = 1; + break; + } + } + break; + + case 1: + /* 32-bit */ + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + unsigned int dw; + dw = pinfo->dimm_params[i][j].data_width; + if (pinfo->dimm_params[i][j].n_ranks + && (dw == 72 || dw == 64)) { + /* + * FIXME: can't really do it + * like this because this just + * further reduces the memory + */ + found = 1; + break; + } + } + if (found) { + dbw_cap_adj[i] = 1; + } + break; + + case 0: + /* 64-bit */ + break; + + default: + printf("unexpected data bus width " + "specified controller %u\n", i); + return 1; + } + debug("dbw_cap_adj[%d]=%d\n", i, dbw_cap_adj[i]); + } + + current_mem_base = CONFIG_SYS_DDR_SDRAM_BASE; + total_mem = 0; + if (pinfo->memctl_opts[0].memctl_interleaving) { + rank_density = pinfo->dimm_params[0][0].rank_density >> + dbw_cap_adj[0]; + switch (pinfo->memctl_opts[0].ba_intlv_ctl & + FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + ctlr_density = 4 * rank_density; + break; + case FSL_DDR_CS0_CS1: + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + ctlr_density = 2 * rank_density; + break; + case FSL_DDR_CS2_CS3: + default: + ctlr_density = rank_density; + break; + } + debug("rank density is 0x%llx, ctlr density is 0x%llx\n", + rank_density, ctlr_density); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (pinfo->memctl_opts[i].memctl_interleaving) { + switch (pinfo->memctl_opts[i].memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + total_ctlr_mem = 2 * ctlr_density; + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + total_ctlr_mem = 3 * ctlr_density; + break; + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + total_ctlr_mem = 4 * ctlr_density; + break; + default: + panic("Unknown interleaving mode"); + } + pinfo->common_timing_params[i].base_address = + current_mem_base; + pinfo->common_timing_params[i].total_mem = + total_ctlr_mem; + total_mem = current_mem_base + total_ctlr_mem; + debug("ctrl %d base 0x%llx\n", i, current_mem_base); + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); + } else { + /* when 3rd controller not interleaved */ + current_mem_base = total_mem; + total_ctlr_mem = 0; + pinfo->common_timing_params[i].base_address = + current_mem_base; + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + unsigned long long cap = + pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; + pinfo->dimm_params[i][j].base_address = + current_mem_base; + debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); + current_mem_base += cap; + total_ctlr_mem += cap; + } + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); + pinfo->common_timing_params[i].total_mem = + total_ctlr_mem; + total_mem += total_ctlr_mem; + } + } + } else { + /* + * Simple linear assignment if memory + * controllers are not interleaved. + */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + total_ctlr_mem = 0; + pinfo->common_timing_params[i].base_address = + current_mem_base; + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + /* Compute DIMM base addresses. */ + unsigned long long cap = + pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; + pinfo->dimm_params[i][j].base_address = + current_mem_base; + debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); + current_mem_base += cap; + total_ctlr_mem += cap; + } + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); + pinfo->common_timing_params[i].total_mem = + total_ctlr_mem; + total_mem += total_ctlr_mem; + } + } + debug("Total mem by %s is 0x%llx\n", __func__, total_mem); + + return total_mem; +} + +/* Use weak function to allow board file to override the address assignment */ +__attribute__((weak, alias("__step_assign_addresses"))) +unsigned long long step_assign_addresses(fsl_ddr_info_t *pinfo, + unsigned int dbw_cap_adj[]); + +unsigned long long +fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, + unsigned int size_only) +{ + unsigned int i, j; + unsigned long long total_mem = 0; + int assert_reset; + + fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg; + common_timing_params_t *timing_params = pinfo->common_timing_params; + assert_reset = board_need_mem_reset(); + + /* data bus width capacity adjust shift amount */ + unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS]; + + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + dbw_capacity_adjust[i] = 0; + } + + debug("starting at step %u (%s)\n", + start_step, step_to_string(start_step)); + + switch (start_step) { + case STEP_GET_SPD: +#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM) + /* STEP 1: Gather all DIMM SPD data */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + fsl_ddr_get_spd(pinfo->spd_installed_dimms[i], i); + } + + case STEP_COMPUTE_DIMM_PARMS: + /* STEP 2: Compute DIMM parameters from SPD data */ + + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + unsigned int retval; + generic_spd_eeprom_t *spd = + &(pinfo->spd_installed_dimms[i][j]); + dimm_params_t *pdimm = + &(pinfo->dimm_params[i][j]); + + retval = compute_dimm_parameters(spd, pdimm, i); +#ifdef CONFIG_SYS_DDR_RAW_TIMING + if (!i && !j && retval) { + printf("SPD error on controller %d! " + "Trying fallback to raw timing " + "calculation\n", i); + fsl_ddr_get_dimm_params(pdimm, i, j); + } +#else + if (retval == 2) { + printf("Error: compute_dimm_parameters" + " non-zero returned FATAL value " + "for memctl=%u dimm=%u\n", i, j); + return 0; + } +#endif + if (retval) { + debug("Warning: compute_dimm_parameters" + " non-zero return value for memctl=%u " + "dimm=%u\n", i, j); + } + } + } + +#elif defined(CONFIG_SYS_DDR_RAW_TIMING) + case STEP_COMPUTE_DIMM_PARMS: + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + dimm_params_t *pdimm = + &(pinfo->dimm_params[i][j]); + fsl_ddr_get_dimm_params(pdimm, i, j); + } + } + debug("Filling dimm parameters from board specific file\n"); +#endif + case STEP_COMPUTE_COMMON_PARMS: + /* + * STEP 3: Compute a common set of timing parameters + * suitable for all of the DIMMs on each memory controller + */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + debug("Computing lowest common DIMM" + " parameters for memctl=%u\n", i); + compute_lowest_common_dimm_parameters( + pinfo->dimm_params[i], + &timing_params[i], + CONFIG_DIMM_SLOTS_PER_CTLR); + } + + case STEP_GATHER_OPTS: + /* STEP 4: Gather configuration requirements from user */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + debug("Reloading memory controller " + "configuration options for memctl=%u\n", i); + /* + * This "reloads" the memory controller options + * to defaults. If the user "edits" an option, + * next_step points to the step after this, + * which is currently STEP_ASSIGN_ADDRESSES. + */ + populate_memctl_options( + timing_params[i].all_dimms_registered, + &pinfo->memctl_opts[i], + pinfo->dimm_params[i], i); + /* + * For RDIMMs, JEDEC spec requires clocks to be stable + * before reset signal is deasserted. For the boards + * using fixed parameters, this function should be + * be called from board init file. + */ + if (timing_params[i].all_dimms_registered) + assert_reset = 1; + } + if (assert_reset) { + debug("Asserting mem reset\n"); + board_assert_mem_reset(); + } + + case STEP_ASSIGN_ADDRESSES: + /* STEP 5: Assign addresses to chip selects */ + check_interleaving_options(pinfo); + total_mem = step_assign_addresses(pinfo, dbw_capacity_adjust); + + case STEP_COMPUTE_REGS: + /* STEP 6: compute controller register values */ + debug("FSL Memory ctrl register computation\n"); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (timing_params[i].ndimms_present == 0) { + memset(&ddr_reg[i], 0, + sizeof(fsl_ddr_cfg_regs_t)); + continue; + } + + compute_fsl_memctl_config_regs( + &pinfo->memctl_opts[i], + &ddr_reg[i], &timing_params[i], + pinfo->dimm_params[i], + dbw_capacity_adjust[i], + size_only); + } + + default: + break; + } + + { + /* + * Compute the amount of memory available just by + * looking for the highest valid CSn_BNDS value. + * This allows us to also experiment with using + * only CS0 when using dual-rank DIMMs. + */ + unsigned int max_end = 0; + + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + for (j = 0; j < CONFIG_CHIP_SELECTS_PER_CTRL; j++) { + fsl_ddr_cfg_regs_t *reg = &ddr_reg[i]; + if (reg->cs[j].config & 0x80000000) { + unsigned int end; + /* + * 0xfffffff is a special value we put + * for unused bnds + */ + if (reg->cs[j].bnds == 0xffffffff) + continue; + end = reg->cs[j].bnds & 0xffff; + if (end > max_end) { + max_end = end; + } + } + } + } + + total_mem = 1 + (((unsigned long long)max_end << 24ULL) | + 0xFFFFFFULL) - CONFIG_SYS_DDR_SDRAM_BASE; + } + + return total_mem; +} + +/* + * fsl_ddr_sdram() -- this is the main function to be called by + * initdram() in the board file. + * + * It returns amount of memory configured in bytes. + */ +phys_size_t fsl_ddr_sdram(void) +{ + unsigned int i; +#ifdef CONFIG_PPC + unsigned int law_memctl = LAW_TRGT_IF_DDR_1; +#endif + unsigned long long total_memory; + fsl_ddr_info_t info; + int deassert_reset; + + /* Reset info structure. */ + memset(&info, 0, sizeof(fsl_ddr_info_t)); + + /* Compute it once normally. */ +#ifdef CONFIG_FSL_DDR_INTERACTIVE + if (tstc() && (getc() == 'd')) { /* we got a key press of 'd' */ + total_memory = fsl_ddr_interactive(&info, 0); + } else if (fsl_ddr_interactive_env_var_exists()) { + total_memory = fsl_ddr_interactive(&info, 1); + } else +#endif + total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 0); + + /* setup 3-way interleaving before enabling DDRC */ + if (info.memctl_opts[0].memctl_interleaving) { + switch (info.memctl_opts[0].memctl_interleaving_mode) { + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + fsl_ddr_set_intl3r( + info.memctl_opts[0].memctl_interleaving_mode); + break; + default: + break; + } + } + + /* + * Program configuration registers. + * JEDEC specs requires clocks to be stable before deasserting reset + * for RDIMMs. Clocks start after chip select is enabled and clock + * control register is set. During step 1, all controllers have their + * registers set but not enabled. Step 2 proceeds after deasserting + * reset through board FPGA or GPIO. + * For non-registered DIMMs, initialization can go through but it is + * also OK to follow the same flow. + */ + deassert_reset = board_need_mem_reset(); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (info.common_timing_params[i].all_dimms_registered) + deassert_reset = 1; + } + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + debug("Programming controller %u\n", i); + if (info.common_timing_params[i].ndimms_present == 0) { + debug("No dimms present on controller %u; " + "skipping programming\n", i); + continue; + } + /* + * The following call with step = 1 returns before enabling + * the controller. It has to finish with step = 2 later. + */ + fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i, + deassert_reset ? 1 : 0); + } + if (deassert_reset) { + /* Use board FPGA or GPIO to deassert reset signal */ + debug("Deasserting mem reset\n"); + board_deassert_mem_reset(); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + /* Call with step = 2 to continue initialization */ + fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), + i, 2); + } + } + +#ifdef CONFIG_PPC + /* program LAWs */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (info.memctl_opts[i].memctl_interleaving) { + switch (info.memctl_opts[i].memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + if (i == 0) { + law_memctl = LAW_TRGT_IF_DDR_INTRLV; + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } else if (i == 2) { + law_memctl = LAW_TRGT_IF_DDR_INTLV_34; + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + law_memctl = LAW_TRGT_IF_DDR_INTLV_123; + if (i == 0) { + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } + break; + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + law_memctl = LAW_TRGT_IF_DDR_INTLV_1234; + if (i == 0) + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + /* place holder for future 4-way interleaving */ + break; + default: + break; + } + } else { + switch (i) { + case 0: + law_memctl = LAW_TRGT_IF_DDR_1; + break; + case 1: + law_memctl = LAW_TRGT_IF_DDR_2; + break; + case 2: + law_memctl = LAW_TRGT_IF_DDR_3; + break; + case 3: + law_memctl = LAW_TRGT_IF_DDR_4; + break; + default: + break; + } + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } + } +#endif + + debug("total_memory by %s = %llu\n", __func__, total_memory); + +#if !defined(CONFIG_PHYS_64BIT) + /* Check for 4G or more. Bad. */ + if (total_memory >= (1ull << 32)) { + puts("Detected "); + print_size(total_memory, " of memory\n"); + printf(" This U-Boot only supports < 4G of DDR\n"); + printf(" You could rebuild it with CONFIG_PHYS_64BIT\n"); + printf(" "); /* re-align to match init_func_ram print */ + total_memory = CONFIG_MAX_MEM_MAPPED; + } +#endif + + return total_memory; +} + +/* + * fsl_ddr_sdram_size() - This function only returns the size of the total + * memory without setting ddr control registers. + */ +phys_size_t +fsl_ddr_sdram_size(void) +{ + fsl_ddr_info_t info; + unsigned long long total_memory = 0; + + memset(&info, 0 , sizeof(fsl_ddr_info_t)); + + /* Compute it once normally. */ + total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 1); + + return total_memory; +} diff --git a/drivers/ddr/fsl/mpc85xx_ddr_gen1.c b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c new file mode 100644 index 000000000..8dd4a9136 --- /dev/null +++ b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c @@ -0,0 +1,91 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <asm/io.h> +#include <fsl_ddr_sdram.h> + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step) +{ + unsigned int i; + struct ccsr_ddr __iomem *ddr = + (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR; + + if (ctrl_num != 0) { + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + out_be32(&ddr->cs0_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs0_config, regs->cs[i].config); + + } else if (i == 1) { + out_be32(&ddr->cs1_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs1_config, regs->cs[i].config); + + } else if (i == 2) { + out_be32(&ddr->cs2_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs2_config, regs->cs[i].config); + + } else if (i == 3) { + out_be32(&ddr->cs3_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs3_config, regs->cs[i].config); + } + } + + out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); +#if defined(CONFIG_MPC8555) || defined(CONFIG_MPC8541) + out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); +#endif + + /* + * 200 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + */ + udelay(200); + asm volatile("sync;isync"); + + out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg); + + asm("sync;isync;msync"); + udelay(500); +} + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +/* + * Initialize all of memory for ECC, then enable errors. + */ + +void +ddr_enable_ecc(unsigned int dram_size) +{ + struct ccsr_ddr __iomem *ddr = + (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR); + + dma_meminit(CONFIG_MEM_INIT_VALUE, dram_size); + + /* + * Enable errors for ECC. + */ + debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable); + ddr->err_disable = 0x00000000; + asm("sync;isync;msync"); + debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable); +} + +#endif /* CONFIG_DDR_ECC && ! CONFIG_ECC_INIT_VIA_DDRCONTROLLER */ diff --git a/drivers/ddr/fsl/mpc85xx_ddr_gen2.c b/drivers/ddr/fsl/mpc85xx_ddr_gen2.c new file mode 100644 index 000000000..988b4a494 --- /dev/null +++ b/drivers/ddr/fsl/mpc85xx_ddr_gen2.c @@ -0,0 +1,96 @@ +/* + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/processor.h> +#include <fsl_ddr_sdram.h> + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step) +{ + unsigned int i; + struct ccsr_ddr __iomem *ddr = + (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR; + +#if defined(CONFIG_SYS_FSL_ERRATUM_NMG_DDR120) && defined(CONFIG_MPC85xx) + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + uint svr; +#endif + + if (ctrl_num) { + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + +#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_DDR120 + /* + * Set the DDR IO receiver to an acceptable bias point. + * Fixed in Rev 2.1. + */ + svr = get_svr(); + if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0)) { + if ((regs->ddr_sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) == + SDRAM_CFG_SDRAM_TYPE_DDR2) + out_be32(&gur->ddrioovcr, 0x90000000); + else + out_be32(&gur->ddrioovcr, 0xA8000000); + } +#endif + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + out_be32(&ddr->cs0_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs0_config, regs->cs[i].config); + + } else if (i == 1) { + out_be32(&ddr->cs1_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs1_config, regs->cs[i].config); + + } else if (i == 2) { + out_be32(&ddr->cs2_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs2_config, regs->cs[i].config); + + } else if (i == 3) { + out_be32(&ddr->cs3_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs3_config, regs->cs[i].config); + } + } + + out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3); + out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0); + out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2); + out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); + out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2); + out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); + out_be32(&ddr->sdram_data_init, regs->ddr_data_init); + out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); + out_be32(&ddr->init_addr, regs->ddr_init_addr); + out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr); + + /* + * 200 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + */ + udelay(200); + asm volatile("sync;isync"); + + out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg); + + /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */ + while (in_be32(&ddr->sdram_cfg_2) & 0x10) { + udelay(10000); /* throttle polling rate */ + } +} diff --git a/drivers/ddr/fsl/mpc85xx_ddr_gen3.c b/drivers/ddr/fsl/mpc85xx_ddr_gen3.c new file mode 100644 index 000000000..9f0413309 --- /dev/null +++ b/drivers/ddr/fsl/mpc85xx_ddr_gen3.c @@ -0,0 +1,464 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <asm/io.h> +#include <fsl_ddr_sdram.h> +#include <asm/processor.h> + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + + +/* + * regs has the to-be-set values for DDR controller registers + * ctrl_num is the DDR controller number + * step: 0 goes through the initialization in one pass + * 1 sets registers and returns before enabling controller + * 2 resumes from step 1 and continues to initialize + * Dividing the initialization to two steps to deassert DDR reset signal + * to comply with JEDEC specs for RDIMMs. + */ +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step) +{ + unsigned int i, bus_width; + struct ccsr_ddr __iomem *ddr; + u32 temp_sdram_cfg; + u32 total_gb_size_per_controller; + int timeout; +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + int timeout_save; + volatile ccsr_local_ecm_t *ecm = (void *)CONFIG_SYS_MPC85xx_ECM_ADDR; + unsigned int csn_bnds_backup = 0, cs_sa, cs_ea, *csn_bnds_t; + int csn = -1; +#endif + + switch (ctrl_num) { + case 0: + ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR; + break; +#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1) + case 1: + ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR; + break; +#endif +#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2) + case 2: + ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR; + break; +#endif +#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3) + case 3: + ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR; + break; +#endif + default: + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + + if (step == 2) + goto step2; + + if (regs->ddr_eor) + out_be32(&ddr->eor, regs->ddr_eor); +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + debug("Workaround for ERRATUM_DDR111_DDR134\n"); + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + cs_sa = (regs->cs[i].bnds >> 16) & 0xfff; + cs_ea = regs->cs[i].bnds & 0xfff; + if ((cs_sa <= 0xff) && (cs_ea >= 0xff)) { + csn = i; + csn_bnds_backup = regs->cs[i].bnds; + csn_bnds_t = (unsigned int *) ®s->cs[i].bnds; + if (cs_ea > 0xeff) + *csn_bnds_t = regs->cs[i].bnds + 0x01000000; + else + *csn_bnds_t = regs->cs[i].bnds + 0x01000100; + debug("Found cs%d_bns (0x%08x) covering 0xff000000, " + "change it to 0x%x\n", + csn, csn_bnds_backup, regs->cs[i].bnds); + break; + } + } +#endif + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + out_be32(&ddr->cs0_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs0_config, regs->cs[i].config); + out_be32(&ddr->cs0_config_2, regs->cs[i].config_2); + + } else if (i == 1) { + out_be32(&ddr->cs1_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs1_config, regs->cs[i].config); + out_be32(&ddr->cs1_config_2, regs->cs[i].config_2); + + } else if (i == 2) { + out_be32(&ddr->cs2_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs2_config, regs->cs[i].config); + out_be32(&ddr->cs2_config_2, regs->cs[i].config_2); + + } else if (i == 3) { + out_be32(&ddr->cs3_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs3_config, regs->cs[i].config); + out_be32(&ddr->cs3_config_2, regs->cs[i].config_2); + } + } + + out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3); + out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0); + out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2); + out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); + out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2); + out_be32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3); + out_be32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4); + out_be32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5); + out_be32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6); + out_be32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7); + out_be32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8); + out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); + out_be32(&ddr->sdram_data_init, regs->ddr_data_init); + out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); + out_be32(&ddr->init_addr, regs->ddr_init_addr); + out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr); + + out_be32(&ddr->timing_cfg_4, regs->timing_cfg_4); + out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5); + out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl); + out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl); +#ifndef CONFIG_SYS_FSL_DDR_EMU + /* + * Skip these two registers if running on emulator + * because emulator doesn't have skew between bytes. + */ + + if (regs->ddr_wrlvl_cntl_2) + out_be32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2); + if (regs->ddr_wrlvl_cntl_3) + out_be32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3); +#endif + + out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr); + out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1); + out_be32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2); + out_be32(&ddr->ddr_cdr1, regs->ddr_cdr1); + out_be32(&ddr->ddr_cdr2, regs->ddr_cdr2); + out_be32(&ddr->err_disable, regs->err_disable); + out_be32(&ddr->err_int_en, regs->err_int_en); + for (i = 0; i < 32; i++) { + if (regs->debug[i]) { + debug("Write to debug_%d as %08x\n", i+1, regs->debug[i]); + out_be32(&ddr->debug[i], regs->debug[i]); + } + } +#ifdef CONFIG_SYS_FSL_ERRATUM_A_004934 + out_be32(&ddr->debug[28], 0x30003000); +#endif + +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR_A003474 + out_be32(&ddr->debug[12], 0x00000015); + out_be32(&ddr->debug[21], 0x24000000); +#endif /* CONFIG_SYS_FSL_ERRATUM_DDR_A003474 */ + + /* + * For RDIMMs, JEDEC spec requires clocks to be stable before reset is + * deasserted. Clocks start when any chip select is enabled and clock + * control register is set. Because all DDR components are connected to + * one reset signal, this needs to be done in two steps. Step 1 is to + * get the clocks started. Step 2 resumes after reset signal is + * deasserted. + */ + if (step == 1) { + udelay(200); + return; + } + +step2: + /* Set, but do not enable the memory */ + temp_sdram_cfg = regs->ddr_sdram_cfg; + temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg); +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR_A003 + debug("Workaround for ERRATUM_DDR_A003\n"); + if (regs->ddr_sdram_rcw_2 & 0x00f00000) { + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2 & 0xf07fffff); + out_be32(&ddr->debug[2], 0x00000400); + out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl & 0x7fffffff); + out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl & 0x7fffffff); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2 & 0xffffffeb); + out_be32(&ddr->mtcr, 0); + out_be32(&ddr->debug[12], 0x00000015); + out_be32(&ddr->debug[21], 0x24000000); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval & 0xffff); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_BI | SDRAM_CFG_MEM_EN); + + asm volatile("sync;isync"); + while (!(in_be32(&ddr->debug[1]) & 0x2)) + ; + + switch (regs->ddr_sdram_rcw_2 & 0x00f00000) { + case 0x00000000: + out_be32(&ddr->sdram_md_cntl, + MD_CNTL_MD_EN | + MD_CNTL_CS_SEL_CS0_CS1 | + 0x04000000 | + MD_CNTL_WRCW | + MD_CNTL_MD_VALUE(0x02)); + break; + case 0x00100000: + out_be32(&ddr->sdram_md_cntl, + MD_CNTL_MD_EN | + MD_CNTL_CS_SEL_CS0_CS1 | + 0x04000000 | + MD_CNTL_WRCW | + MD_CNTL_MD_VALUE(0x0a)); + break; + case 0x00200000: + out_be32(&ddr->sdram_md_cntl, + MD_CNTL_MD_EN | + MD_CNTL_CS_SEL_CS0_CS1 | + 0x04000000 | + MD_CNTL_WRCW | + MD_CNTL_MD_VALUE(0x12)); + break; + case 0x00300000: + out_be32(&ddr->sdram_md_cntl, + MD_CNTL_MD_EN | + MD_CNTL_CS_SEL_CS0_CS1 | + 0x04000000 | + MD_CNTL_WRCW | + MD_CNTL_MD_VALUE(0x1a)); + break; + default: + out_be32(&ddr->sdram_md_cntl, + MD_CNTL_MD_EN | + MD_CNTL_CS_SEL_CS0_CS1 | + 0x04000000 | + MD_CNTL_WRCW | + MD_CNTL_MD_VALUE(0x02)); + printf("Unsupported RC10\n"); + break; + } + + while (in_be32(&ddr->sdram_md_cntl) & 0x80000000) + ; + udelay(6); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->debug[2], 0x0); + out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl); + out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2); + out_be32(&ddr->debug[12], 0x0); + out_be32(&ddr->debug[21], 0x0); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); + + } +#endif + /* + * For 8572 DDR1 erratum - DDR controller may enter illegal state + * when operatiing in 32-bit bus mode with 4-beat bursts, + * This erratum does not affect DDR3 mode, only for DDR2 mode. + */ +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR_115 + debug("Workaround for ERRATUM_DDR_115\n"); + if ((((in_be32(&ddr->sdram_cfg) >> 24) & 0x7) == SDRAM_TYPE_DDR2) + && in_be32(&ddr->sdram_cfg) & 0x80000) { + /* set DEBUG_1[31] */ + setbits_be32(&ddr->debug[0], 1); + } +#endif +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + debug("Workaround for ERRATUM_DDR111_DDR134\n"); + /* + * This is the combined workaround for DDR111 and DDR134 + * following the published errata for MPC8572 + */ + + /* 1. Set EEBACR[3] */ + setbits_be32(&ecm->eebacr, 0x10000000); + debug("Setting EEBACR[3] to 0x%08x\n", in_be32(&ecm->eebacr)); + + /* 2. Set DINIT in SDRAM_CFG_2*/ + setbits_be32(&ddr->sdram_cfg_2, SDRAM_CFG2_D_INIT); + debug("Setting sdram_cfg_2[D_INIT] to 0x%08x\n", + in_be32(&ddr->sdram_cfg_2)); + + /* 3. Set DEBUG_3[21] */ + setbits_be32(&ddr->debug[2], 0x400); + debug("Setting DEBUG_3[21] to 0x%08x\n", in_be32(&ddr->debug[2])); + +#endif /* part 1 of the workaound */ + + /* + * 500 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + * DDR2 need 200 us, and DDR3 need 500 us from spec, + * we choose the max, that is 500 us for all of case. + */ + udelay(500); + asm volatile("sync;isync"); + + /* Let the controller go */ + temp_sdram_cfg = in_be32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI; + out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN); + asm volatile("sync;isync"); + + total_gb_size_per_controller = 0; + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (!(regs->cs[i].config & 0x80000000)) + continue; + total_gb_size_per_controller += 1 << ( + ((regs->cs[i].config >> 14) & 0x3) + 2 + + ((regs->cs[i].config >> 8) & 0x7) + 12 + + ((regs->cs[i].config >> 0) & 0x7) + 8 + + 3 - ((regs->ddr_sdram_cfg >> 19) & 0x3) - + 26); /* minus 26 (count of 64M) */ + } + if (fsl_ddr_get_intl3r() & 0x80000000) /* 3-way interleaving */ + total_gb_size_per_controller *= 3; + else if (regs->cs[0].config & 0x20000000) /* 2-way interleaving */ + total_gb_size_per_controller <<= 1; + /* + * total memory / bus width = transactions needed + * transactions needed / data rate = seconds + * to add plenty of buffer, double the time + * For example, 2GB on 666MT/s 64-bit bus takes about 402ms + * Let's wait for 800ms + */ + bus_width = 3 - ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK) + >> SDRAM_CFG_DBW_SHIFT); + timeout = ((total_gb_size_per_controller << (6 - bus_width)) * 100 / + (get_ddr_freq(0) >> 20)) << 1; +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + timeout_save = timeout; +#endif + total_gb_size_per_controller >>= 4; /* shift down to gb size */ + debug("total %d GB\n", total_gb_size_per_controller); + debug("Need to wait up to %d * 10ms\n", timeout); + + /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */ + while ((in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) && + (timeout >= 0)) { + udelay(10000); /* throttle polling rate */ + timeout--; + } + + if (timeout <= 0) + printf("Waiting for D_INIT timeout. Memory may not work.\n"); + +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + /* continue this workaround */ + + /* 4. Clear DEBUG3[21] */ + clrbits_be32(&ddr->debug[2], 0x400); + debug("Clearing D3[21] to 0x%08x\n", in_be32(&ddr->debug[2])); + + /* DDR134 workaround starts */ + /* A: Clear sdram_cfg_2[odt_cfg] */ + clrbits_be32(&ddr->sdram_cfg_2, SDRAM_CFG2_ODT_CFG_MASK); + debug("Clearing SDRAM_CFG2[ODT_CFG] to 0x%08x\n", + in_be32(&ddr->sdram_cfg_2)); + + /* B: Set DEBUG1[15] */ + setbits_be32(&ddr->debug[0], 0x10000); + debug("Setting D1[15] to 0x%08x\n", in_be32(&ddr->debug[0])); + + /* C: Set timing_cfg_2[cpo] to 0b11111 */ + setbits_be32(&ddr->timing_cfg_2, TIMING_CFG_2_CPO_MASK); + debug("Setting TMING_CFG_2[CPO] to 0x%08x\n", + in_be32(&ddr->timing_cfg_2)); + + /* D: Set D6 to 0x9f9f9f9f */ + out_be32(&ddr->debug[5], 0x9f9f9f9f); + debug("Setting D6 to 0x%08x\n", in_be32(&ddr->debug[5])); + + /* E: Set D7 to 0x9f9f9f9f */ + out_be32(&ddr->debug[6], 0x9f9f9f9f); + debug("Setting D7 to 0x%08x\n", in_be32(&ddr->debug[6])); + + /* F: Set D2[20] */ + setbits_be32(&ddr->debug[1], 0x800); + debug("Setting D2[20] to 0x%08x\n", in_be32(&ddr->debug[1])); + + /* G: Poll on D2[20] until cleared */ + while (in_be32(&ddr->debug[1]) & 0x800) + udelay(10000); /* throttle polling rate */ + + /* H: Clear D1[15] */ + clrbits_be32(&ddr->debug[0], 0x10000); + debug("Setting D1[15] to 0x%08x\n", in_be32(&ddr->debug[0])); + + /* I: Set sdram_cfg_2[odt_cfg] */ + setbits_be32(&ddr->sdram_cfg_2, + regs->ddr_sdram_cfg_2 & SDRAM_CFG2_ODT_CFG_MASK); + debug("Setting sdram_cfg_2 to 0x%08x\n", in_be32(&ddr->sdram_cfg_2)); + + /* Continuing with the DDR111 workaround */ + /* 5. Set D2[21] */ + setbits_be32(&ddr->debug[1], 0x400); + debug("Setting D2[21] to 0x%08x\n", in_be32(&ddr->debug[1])); + + /* 6. Poll D2[21] until its cleared */ + while (in_be32(&ddr->debug[1]) & 0x400) + udelay(10000); /* throttle polling rate */ + + /* 7. Wait for state machine 2nd run, roughly 400ms/GB */ + debug("Wait for %d * 10ms\n", timeout_save); + udelay(timeout_save * 10000); + + /* 8. Set sdram_cfg_2[dinit] if options requires */ + setbits_be32(&ddr->sdram_cfg_2, + regs->ddr_sdram_cfg_2 & SDRAM_CFG2_D_INIT); + debug("Setting sdram_cfg_2 to 0x%08x\n", in_be32(&ddr->sdram_cfg_2)); + + /* 9. Poll until dinit is cleared */ + timeout = timeout_save; + debug("Need to wait up to %d * 10ms\n", timeout); + while ((in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) && + (timeout >= 0)) { + udelay(10000); /* throttle polling rate */ + timeout--; + } + + if (timeout <= 0) + printf("Waiting for D_INIT timeout. Memory may not work.\n"); + + /* 10. Clear EEBACR[3] */ + clrbits_be32(&ecm->eebacr, 10000000); + debug("Clearing EEBACR[3] to 0x%08x\n", in_be32(&ecm->eebacr)); + + if (csn != -1) { + csn_bnds_t = (unsigned int *) ®s->cs[csn].bnds; + *csn_bnds_t = csn_bnds_backup; + debug("Change cs%d_bnds back to 0x%08x\n", + csn, regs->cs[csn].bnds); + setbits_be32(&ddr->sdram_cfg, 0x2); /* MEM_HALT */ + switch (csn) { + case 0: + out_be32(&ddr->cs0_bnds, regs->cs[csn].bnds); + break; + case 1: + out_be32(&ddr->cs1_bnds, regs->cs[csn].bnds); + break; + case 2: + out_be32(&ddr->cs2_bnds, regs->cs[csn].bnds); + break; + case 3: + out_be32(&ddr->cs3_bnds, regs->cs[csn].bnds); + break; + } + clrbits_be32(&ddr->sdram_cfg, 0x2); + } +#endif /* CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 */ +} diff --git a/drivers/ddr/fsl/mpc86xx_ddr.c b/drivers/ddr/fsl/mpc86xx_ddr.c new file mode 100644 index 000000000..4551ed87d --- /dev/null +++ b/drivers/ddr/fsl/mpc86xx_ddr.c @@ -0,0 +1,85 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <asm/io.h> +#include <fsl_ddr_sdram.h> + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step) +{ + unsigned int i; + struct ccsr_ddr __iomem *ddr; + + switch (ctrl_num) { + case 0: + ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR; + break; + case 1: + ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR; + break; + default: + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + out_be32(&ddr->cs0_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs0_config, regs->cs[i].config); + + } else if (i == 1) { + out_be32(&ddr->cs1_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs1_config, regs->cs[i].config); + + } else if (i == 2) { + out_be32(&ddr->cs2_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs2_config, regs->cs[i].config); + + } else if (i == 3) { + out_be32(&ddr->cs3_bnds, regs->cs[i].bnds); + out_be32(&ddr->cs3_config, regs->cs[i].config); + } + } + + out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3); + out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0); + out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); + out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); + out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2); + out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); + out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2); + out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl); + out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); + out_be32(&ddr->sdram_data_init, regs->ddr_data_init); + out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); + out_be32(&ddr->init_addr, regs->ddr_init_addr); + out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr); + + debug("before go\n"); + + /* + * 200 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + */ + udelay(200); + asm volatile("sync;isync"); + + out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg); + + /* + * Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done + */ + while (in_be32(&ddr->sdram_cfg_2) & 0x10) { + udelay(10000); /* throttle polling rate */ + } +} diff --git a/drivers/ddr/fsl/options.c b/drivers/ddr/fsl/options.c new file mode 100644 index 000000000..4aafcceaf --- /dev/null +++ b/drivers/ddr/fsl/options.c @@ -0,0 +1,1147 @@ +/* + * Copyright 2008, 2010-2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <hwconfig.h> +#include <fsl_ddr_sdram.h> + +#include <fsl_ddr.h> + +/* + * Use our own stack based buffer before relocation to allow accessing longer + * hwconfig strings that might be in the environment before we've relocated. + * This is pretty fragile on both the use of stack and if the buffer is big + * enough. However we will get a warning from getenv_f for the later. + */ + +/* Board-specific functions defined in each board's ddr.c */ +extern void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num); + +struct dynamic_odt { + unsigned int odt_rd_cfg; + unsigned int odt_wr_cfg; + unsigned int odt_rtt_norm; + unsigned int odt_rtt_wr; +}; + +#ifdef CONFIG_SYS_FSL_DDR3 +static const struct dynamic_odt single_Q[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS_AND_OTHER_DIMM, + DDR3_RTT_20_OHM, + DDR3_RTT_120_OHM + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, /* tied high */ + DDR3_RTT_OFF, + DDR3_RTT_120_OHM + }, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS_AND_OTHER_DIMM, + DDR3_RTT_20_OHM, + DDR3_RTT_120_OHM + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, /* tied high */ + DDR3_RTT_OFF, + DDR3_RTT_120_OHM + } +}; + +static const struct dynamic_odt single_D[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR3_RTT_OFF, + DDR3_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt single_S[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0}, +}; + +static const struct dynamic_odt dual_DD[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR3_RTT_30_OHM, + DDR3_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR3_RTT_30_OHM, + DDR3_RTT_OFF + } +}; + +static const struct dynamic_odt dual_DS[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR3_RTT_30_OHM, + DDR3_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_ALL, + DDR3_RTT_20_OHM, + DDR3_RTT_120_OHM + }, + {0, 0, 0, 0} +}; +static const struct dynamic_odt dual_SD[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_ALL, + DDR3_RTT_20_OHM, + DDR3_RTT_120_OHM + }, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR3_RTT_20_OHM, + DDR3_RTT_OFF + } +}; + +static const struct dynamic_odt dual_SS[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_ALL, + DDR3_RTT_30_OHM, + DDR3_RTT_120_OHM + }, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_ALL, + DDR3_RTT_30_OHM, + DDR3_RTT_120_OHM + }, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt dual_D0[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR3_RTT_OFF, + DDR3_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt dual_0D[4] = { + {0, 0, 0, 0}, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_SAME_DIMM, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR3_RTT_OFF, + DDR3_RTT_OFF + } +}; + +static const struct dynamic_odt dual_S0[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0} + +}; + +static const struct dynamic_odt dual_0S[4] = { + {0, 0, 0, 0}, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_40_OHM, + DDR3_RTT_OFF + }, + {0, 0, 0, 0} + +}; + +static const struct dynamic_odt odt_unknown[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR3_RTT_120_OHM, + DDR3_RTT_OFF + } +}; +#else /* CONFIG_SYS_FSL_DDR3 */ +static const struct dynamic_odt single_Q[4] = { + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt single_D[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt single_S[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0}, +}; + +static const struct dynamic_odt dual_DD[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + } +}; + +static const struct dynamic_odt dual_DS[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt dual_SD[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + } +}; + +static const struct dynamic_odt dual_SS[4] = { + { /* cs0 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_OTHER_DIMM, + FSL_DDR_ODT_OTHER_DIMM, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt dual_D0[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0} +}; + +static const struct dynamic_odt dual_0D[4] = { + {0, 0, 0, 0}, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_ALL, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + } +}; + +static const struct dynamic_odt dual_S0[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0}, + {0, 0, 0, 0}, + {0, 0, 0, 0} + +}; + +static const struct dynamic_odt dual_0S[4] = { + {0, 0, 0, 0}, + {0, 0, 0, 0}, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR2_RTT_150_OHM, + DDR2_RTT_OFF + }, + {0, 0, 0, 0} + +}; + +static const struct dynamic_odt odt_unknown[4] = { + { /* cs0 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs1 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + }, + { /* cs2 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_CS, + DDR2_RTT_75_OHM, + DDR2_RTT_OFF + }, + { /* cs3 */ + FSL_DDR_ODT_NEVER, + FSL_DDR_ODT_NEVER, + DDR2_RTT_OFF, + DDR2_RTT_OFF + } +}; +#endif + +/* + * Automatically seleect bank interleaving mode based on DIMMs + * in this order: cs0_cs1_cs2_cs3, cs0_cs1, null. + * This function only deal with one or two slots per controller. + */ +static inline unsigned int auto_bank_intlv(dimm_params_t *pdimm) +{ +#if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) + if (pdimm[0].n_ranks == 4) + return FSL_DDR_CS0_CS1_CS2_CS3; + else if (pdimm[0].n_ranks == 2) + return FSL_DDR_CS0_CS1; +#elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +#ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + if (pdimm[0].n_ranks == 4) + return FSL_DDR_CS0_CS1_CS2_CS3; +#endif + if (pdimm[0].n_ranks == 2) { + if (pdimm[1].n_ranks == 2) + return FSL_DDR_CS0_CS1_CS2_CS3; + else + return FSL_DDR_CS0_CS1; + } +#endif + return 0; +} + +unsigned int populate_memctl_options(int all_dimms_registered, + memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + unsigned int i; + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; +#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) + const struct dynamic_odt *pdodt = odt_unknown; +#endif + ulong ddr_freq; + + /* + * Extract hwconfig from environment since we have not properly setup + * the environment but need it for ddr config params + */ + if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0) + buf = buffer; + +#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) + /* Chip select options. */ + if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) { + switch (pdimm[0].n_ranks) { + case 1: + pdodt = single_S; + break; + case 2: + pdodt = single_D; + break; + case 4: + pdodt = single_Q; + break; + } + } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) { + switch (pdimm[0].n_ranks) { +#ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + case 4: + pdodt = single_Q; + if (pdimm[1].n_ranks) + printf("Error: Quad- and Dual-rank DIMMs " + "cannot be used together\n"); + break; +#endif + case 2: + switch (pdimm[1].n_ranks) { + case 2: + pdodt = dual_DD; + break; + case 1: + pdodt = dual_DS; + break; + case 0: + pdodt = dual_D0; + break; + } + break; + case 1: + switch (pdimm[1].n_ranks) { + case 2: + pdodt = dual_SD; + break; + case 1: + pdodt = dual_SS; + break; + case 0: + pdodt = dual_S0; + break; + } + break; + case 0: + switch (pdimm[1].n_ranks) { + case 2: + pdodt = dual_0D; + break; + case 1: + pdodt = dual_0S; + break; + } + break; + } + } +#endif + + /* Pick chip-select local options. */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { +#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) + popts->cs_local_opts[i].odt_rd_cfg = pdodt[i].odt_rd_cfg; + popts->cs_local_opts[i].odt_wr_cfg = pdodt[i].odt_wr_cfg; + popts->cs_local_opts[i].odt_rtt_norm = pdodt[i].odt_rtt_norm; + popts->cs_local_opts[i].odt_rtt_wr = pdodt[i].odt_rtt_wr; +#else + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; +#endif + popts->cs_local_opts[i].auto_precharge = 0; + } + + /* Pick interleaving mode. */ + + /* + * 0 = no interleaving + * 1 = interleaving between 2 controllers + */ + popts->memctl_interleaving = 0; + + /* + * 0 = cacheline + * 1 = page + * 2 = (logical) bank + * 3 = superbank (only if CS interleaving is enabled) + */ + popts->memctl_interleaving_mode = 0; + + /* + * 0: cacheline: bit 30 of the 36-bit physical addr selects the memctl + * 1: page: bit to the left of the column bits selects the memctl + * 2: bank: bit to the left of the bank bits selects the memctl + * 3: superbank: bit to the left of the chip select selects the memctl + * + * NOTE: ba_intlv (rank interleaving) is independent of memory + * controller interleaving; it is only within a memory controller. + * Must use superbank interleaving if rank interleaving is used and + * memory controller interleaving is enabled. + */ + + /* + * 0 = no + * 0x40 = CS0,CS1 + * 0x20 = CS2,CS3 + * 0x60 = CS0,CS1 + CS2,CS3 + * 0x04 = CS0,CS1,CS2,CS3 + */ + popts->ba_intlv_ctl = 0; + + /* Memory Organization Parameters */ + popts->registered_dimm_en = all_dimms_registered; + + /* Operational Mode Paramters */ + + /* Pick ECC modes */ + popts->ecc_mode = 0; /* 0 = disabled, 1 = enabled */ +#ifdef CONFIG_DDR_ECC + if (hwconfig_sub_f("fsl_ddr", "ecc", buf)) { + if (hwconfig_subarg_cmp_f("fsl_ddr", "ecc", "on", buf)) + popts->ecc_mode = 1; + } else + popts->ecc_mode = 1; +#endif + popts->ecc_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */ + + /* + * Choose DQS config + * 0 for DDR1 + * 1 for DDR2 + */ +#if defined(CONFIG_SYS_FSL_DDR1) + popts->dqs_config = 0; +#elif defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3) + popts->dqs_config = 1; +#endif + + /* Choose self-refresh during sleep. */ + popts->self_refresh_in_sleep = 1; + + /* Choose dynamic power management mode. */ + popts->dynamic_power = 0; + + /* + * check first dimm for primary sdram width + * presuming all dimms are similar + * 0 = 64-bit, 1 = 32-bit, 2 = 16-bit + */ +#if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2) + if (pdimm[0].n_ranks != 0) { + if ((pdimm[0].data_width >= 64) && \ + (pdimm[0].data_width <= 72)) + popts->data_bus_width = 0; + else if ((pdimm[0].data_width >= 32) || \ + (pdimm[0].data_width <= 40)) + popts->data_bus_width = 1; + else { + panic("Error: data width %u is invalid!\n", + pdimm[0].data_width); + } + } +#else + if (pdimm[0].n_ranks != 0) { + if (pdimm[0].primary_sdram_width == 64) + popts->data_bus_width = 0; + else if (pdimm[0].primary_sdram_width == 32) + popts->data_bus_width = 1; + else if (pdimm[0].primary_sdram_width == 16) + popts->data_bus_width = 2; + else { + panic("Error: primary sdram width %u is invalid!\n", + pdimm[0].primary_sdram_width); + } + } +#endif + + popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0; + + /* Choose burst length. */ +#if defined(CONFIG_SYS_FSL_DDR3) +#if defined(CONFIG_E500MC) + popts->otf_burst_chop_en = 0; /* on-the-fly burst chop disable */ + popts->burst_length = DDR_BL8; /* Fixed 8-beat burst len */ +#else + if ((popts->data_bus_width == 1) || (popts->data_bus_width == 2)) { + /* 32-bit or 16-bit bus */ + popts->otf_burst_chop_en = 0; + popts->burst_length = DDR_BL8; + } else { + popts->otf_burst_chop_en = 1; /* on-the-fly burst chop */ + popts->burst_length = DDR_OTF; /* on-the-fly BC4 and BL8 */ + } +#endif +#else + popts->burst_length = DDR_BL4; /* has to be 4 for DDR2 */ +#endif + + /* Choose ddr controller address mirror mode */ +#if defined(CONFIG_SYS_FSL_DDR3) + popts->mirrored_dimm = pdimm[0].mirrored_dimm; +#endif + + /* Global Timing Parameters. */ + debug("mclk_ps = %u ps\n", get_memory_clk_period_ps()); + + /* Pick a caslat override. */ + popts->cas_latency_override = 0; + popts->cas_latency_override_value = 3; + if (popts->cas_latency_override) { + debug("using caslat override value = %u\n", + popts->cas_latency_override_value); + } + + /* Decide whether to use the computed derated latency */ + popts->use_derated_caslat = 0; + + /* Choose an additive latency. */ + popts->additive_latency_override = 0; + popts->additive_latency_override_value = 3; + if (popts->additive_latency_override) { + debug("using additive latency override value = %u\n", + popts->additive_latency_override_value); + } + + /* + * 2T_EN setting + * + * Factors to consider for 2T_EN: + * - number of DIMMs installed + * - number of components, number of active ranks + * - how much time you want to spend playing around + */ + popts->twot_en = 0; + popts->threet_en = 0; + + /* for RDIMM, address parity enable */ + popts->ap_en = 1; + + /* + * BSTTOPRE precharge interval + * + * Set this to 0 for global auto precharge + * + * FIXME: Should this be configured in picoseconds? + * Why it should be in ps: better understanding of this + * relative to actual DRAM timing parameters such as tRAS. + * e.g. tRAS(min) = 40 ns + */ + popts->bstopre = 0x100; + + /* Minimum CKE pulse width -- tCKE(MIN) */ + popts->tcke_clock_pulse_width_ps + = mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR); + + /* + * Window for four activates -- tFAW + * + * FIXME: UM: applies only to DDR2/DDR3 with eight logical banks only + * FIXME: varies depending upon number of column addresses or data + * FIXME: width, was considering looking at pdimm->primary_sdram_width + */ +#if defined(CONFIG_SYS_FSL_DDR1) + popts->tfaw_window_four_activates_ps = mclk_to_picos(1); + +#elif defined(CONFIG_SYS_FSL_DDR2) + /* + * x4/x8; some datasheets have 35000 + * x16 wide columns only? Use 50000? + */ + popts->tfaw_window_four_activates_ps = 37500; + +#elif defined(CONFIG_SYS_FSL_DDR3) + popts->tfaw_window_four_activates_ps = pdimm[0].tfaw_ps; +#endif + popts->zq_en = 0; + popts->wrlvl_en = 0; +#if defined(CONFIG_SYS_FSL_DDR3) + /* + * due to ddr3 dimm is fly-by topology + * we suggest to enable write leveling to + * meet the tQDSS under different loading. + */ + popts->wrlvl_en = 1; + popts->zq_en = 1; + popts->wrlvl_override = 0; +#endif + + /* + * Check interleaving configuration from environment. + * Please refer to doc/README.fsl-ddr for the detail. + * + * If memory controller interleaving is enabled, then the data + * bus widths must be programmed identically for all memory controllers. + * + * XXX: Attempt to set all controllers to the same chip select + * interleaving mode. It will do a best effort to get the + * requested ranks interleaved together such that the result + * should be a subset of the requested configuration. + */ +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + if (!hwconfig_sub_f("fsl_ddr", "ctlr_intlv", buf)) + goto done; + + if (pdimm[0].n_ranks == 0) { + printf("There is no rank on CS0 for controller %d.\n", ctrl_num); + popts->memctl_interleaving = 0; + goto done; + } + popts->memctl_interleaving = 1; + /* + * test null first. if CONFIG_HWCONFIG is not defined + * hwconfig_arg_cmp returns non-zero + */ + if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", + "null", buf)) { + popts->memctl_interleaving = 0; + debug("memory controller interleaving disabled.\n"); + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "cacheline", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_CACHE_LINE_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "page", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_PAGE_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "bank", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_BANK_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "superbank", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_SUPERBANK_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; +#if (CONFIG_NUM_DDR_CONTROLLERS == 3) + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_1KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_1KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_4KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_4KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_8KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_8KB_INTERLEAVING; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 4) + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_1KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_1KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_4KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_4KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_8KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_8KB_INTERLEAVING; +#endif + } else { + popts->memctl_interleaving = 0; + printf("hwconfig has unrecognized parameter for ctlr_intlv.\n"); + } +done: +#endif + if ((hwconfig_sub_f("fsl_ddr", "bank_intlv", buf)) && + (CONFIG_CHIP_SELECTS_PER_CTRL > 1)) { + /* test null first. if CONFIG_HWCONFIG is not defined, + * hwconfig_subarg_cmp_f returns non-zero */ + if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "null", buf)) + debug("bank interleaving disabled.\n"); + else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "cs0_cs1", buf)) + popts->ba_intlv_ctl = FSL_DDR_CS0_CS1; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "cs2_cs3", buf)) + popts->ba_intlv_ctl = FSL_DDR_CS2_CS3; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "cs0_cs1_and_cs2_cs3", buf)) + popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_AND_CS2_CS3; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "cs0_cs1_cs2_cs3", buf)) + popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_CS2_CS3; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", + "auto", buf)) + popts->ba_intlv_ctl = auto_bank_intlv(pdimm); + else + printf("hwconfig has unrecognized parameter for bank_intlv.\n"); + switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: +#if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) + if (pdimm[0].n_ranks < 4) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(chip-select) for " + "CS0+CS1+CS2+CS3 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } +#elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +#ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + if (pdimm[0].n_ranks == 4) + break; +#endif + if ((pdimm[0].n_ranks < 2) && (pdimm[1].n_ranks < 2)) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(chip-select) for " + "CS0+CS1+CS2+CS3 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } + if (pdimm[0].capacity != pdimm[1].capacity) { + popts->ba_intlv_ctl = 0; + printf("Not identical DIMM size for " + "CS0+CS1+CS2+CS3 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } +#endif + break; + case FSL_DDR_CS0_CS1: + if (pdimm[0].n_ranks < 2) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(chip-select) for " + "CS0+CS1 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } + break; + case FSL_DDR_CS2_CS3: +#if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) + if (pdimm[0].n_ranks < 4) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(chip-select) for CS2+CS3 " + "on controller %d, interleaving disabled!\n", ctrl_num); + } +#elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) + if (pdimm[1].n_ranks < 2) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(chip-select) for CS2+CS3 " + "on controller %d, interleaving disabled!\n", ctrl_num); + } +#endif + break; + case FSL_DDR_CS0_CS1_AND_CS2_CS3: +#if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) + if (pdimm[0].n_ranks < 4) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(CS) for CS0+CS1 and " + "CS2+CS3 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } +#elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) + if ((pdimm[0].n_ranks < 2) || (pdimm[1].n_ranks < 2)) { + popts->ba_intlv_ctl = 0; + printf("Not enough bank(CS) for CS0+CS1 and " + "CS2+CS3 on controller %d, " + "interleaving disabled!\n", ctrl_num); + } +#endif + break; + default: + popts->ba_intlv_ctl = 0; + break; + } + } + + if (hwconfig_sub_f("fsl_ddr", "addr_hash", buf)) { + if (hwconfig_subarg_cmp_f("fsl_ddr", "addr_hash", "null", buf)) + popts->addr_hash = 0; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "addr_hash", + "true", buf)) + popts->addr_hash = 1; + } + + if (pdimm[0].n_ranks == 4) + popts->quad_rank_present = 1; + + ddr_freq = get_ddr_freq(0) / 1000000; + if (popts->registered_dimm_en) { + popts->rcw_override = 1; + popts->rcw_1 = 0x000a5a00; + if (ddr_freq <= 800) + popts->rcw_2 = 0x00000000; + else if (ddr_freq <= 1066) + popts->rcw_2 = 0x00100000; + else if (ddr_freq <= 1333) + popts->rcw_2 = 0x00200000; + else + popts->rcw_2 = 0x00300000; + } + + fsl_ddr_board_options(popts, pdimm, ctrl_num); + + return 0; +} + +void check_interleaving_options(fsl_ddr_info_t *pinfo) +{ + int i, j, k, check_n_ranks, intlv_invalid = 0; + unsigned int check_intlv, check_n_row_addr, check_n_col_addr; + unsigned long long check_rank_density; + struct dimm_params_s *dimm; + /* + * Check if all controllers are configured for memory + * controller interleaving. Identical dimms are recommended. At least + * the size, row and col address should be checked. + */ + j = 0; + check_n_ranks = pinfo->dimm_params[0][0].n_ranks; + check_rank_density = pinfo->dimm_params[0][0].rank_density; + check_n_row_addr = pinfo->dimm_params[0][0].n_row_addr; + check_n_col_addr = pinfo->dimm_params[0][0].n_col_addr; + check_intlv = pinfo->memctl_opts[0].memctl_interleaving_mode; + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + dimm = &pinfo->dimm_params[i][0]; + if (!pinfo->memctl_opts[i].memctl_interleaving) { + continue; + } else if (((check_rank_density != dimm->rank_density) || + (check_n_ranks != dimm->n_ranks) || + (check_n_row_addr != dimm->n_row_addr) || + (check_n_col_addr != dimm->n_col_addr) || + (check_intlv != + pinfo->memctl_opts[i].memctl_interleaving_mode))){ + intlv_invalid = 1; + break; + } else { + j++; + } + + } + if (intlv_invalid) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) + pinfo->memctl_opts[i].memctl_interleaving = 0; + printf("Not all DIMMs are identical. " + "Memory controller interleaving disabled.\n"); + } else { + switch (check_intlv) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + if (3 == CONFIG_NUM_DDR_CONTROLLERS) + k = 2; + else + k = CONFIG_NUM_DDR_CONTROLLERS; + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + default: + k = CONFIG_NUM_DDR_CONTROLLERS; + break; + } + debug("%d of %d controllers are interleaving.\n", j, k); + if (j && (j != k)) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) + pinfo->memctl_opts[i].memctl_interleaving = 0; + printf("Not all controllers have compatible " + "interleaving mode. All disabled.\n"); + } + } + debug("Checking interleaving options completed\n"); +} + +int fsl_use_spd(void) +{ + int use_spd = 0; + +#ifdef CONFIG_DDR_SPD + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; + + /* + * Extract hwconfig from environment since we have not properly setup + * the environment but need it for ddr config params + */ + if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0) + buf = buffer; + + /* if hwconfig is not enabled, or "sdram" is not defined, use spd */ + if (hwconfig_sub_f("fsl_ddr", "sdram", buf)) { + if (hwconfig_subarg_cmp_f("fsl_ddr", "sdram", "spd", buf)) + use_spd = 1; + else if (hwconfig_subarg_cmp_f("fsl_ddr", "sdram", + "fixed", buf)) + use_spd = 0; + else + use_spd = 1; + } else + use_spd = 1; +#endif + + return use_spd; +} diff --git a/drivers/ddr/fsl/util.c b/drivers/ddr/fsl/util.c new file mode 100644 index 000000000..0658261d8 --- /dev/null +++ b/drivers/ddr/fsl/util.c @@ -0,0 +1,271 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#ifdef CONFIG_PPC +#include <asm/fsl_law.h> +#endif +#include <div64.h> + +#include <fsl_ddr.h> +#include <fsl_immap.h> +#include <asm/io.h> + +/* To avoid 64-bit full-divides, we factor this here */ +#define ULL_2E12 2000000000000ULL +#define UL_5POW12 244140625UL +#define UL_2POW13 (1UL << 13) + +#define ULL_8FS 0xFFFFFFFFULL + +/* + * Round up mclk_ps to nearest 1 ps in memory controller code + * if the error is 0.5ps or more. + * + * If an imprecise data rate is too high due to rounding error + * propagation, compute a suitably rounded mclk_ps to compute + * a working memory controller configuration. + */ +unsigned int get_memory_clk_period_ps(void) +{ + unsigned int data_rate = get_ddr_freq(0); + unsigned int result; + + /* Round to nearest 10ps, being careful about 64-bit multiply/divide */ + unsigned long long rem, mclk_ps = ULL_2E12; + + /* Now perform the big divide, the result fits in 32-bits */ + rem = do_div(mclk_ps, data_rate); + result = (rem >= (data_rate >> 1)) ? mclk_ps + 1 : mclk_ps; + + return result; +} + +/* Convert picoseconds into DRAM clock cycles (rounding up if needed). */ +unsigned int picos_to_mclk(unsigned int picos) +{ + unsigned long long clks, clks_rem; + unsigned long data_rate = get_ddr_freq(0); + + /* Short circuit for zero picos */ + if (!picos) + return 0; + + /* First multiply the time by the data rate (32x32 => 64) */ + clks = picos * (unsigned long long)data_rate; + /* + * Now divide by 5^12 and track the 32-bit remainder, then divide + * by 2*(2^12) using shifts (and updating the remainder). + */ + clks_rem = do_div(clks, UL_5POW12); + clks_rem += (clks & (UL_2POW13-1)) * UL_5POW12; + clks >>= 13; + + /* If we had a remainder greater than the 1ps error, then round up */ + if (clks_rem > data_rate) + clks++; + + /* Clamp to the maximum representable value */ + if (clks > ULL_8FS) + clks = ULL_8FS; + return (unsigned int) clks; +} + +unsigned int mclk_to_picos(unsigned int mclk) +{ + return get_memory_clk_period_ps() * mclk; +} + +#ifdef CONFIG_PPC +void +__fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params, + unsigned int law_memctl, + unsigned int ctrl_num) +{ + unsigned long long base = memctl_common_params->base_address; + unsigned long long size = memctl_common_params->total_mem; + + /* + * If no DIMMs on this controller, do not proceed any further. + */ + if (!memctl_common_params->ndimms_present) { + return; + } + +#if !defined(CONFIG_PHYS_64BIT) + if (base >= CONFIG_MAX_MEM_MAPPED) + return; + if ((base + size) >= CONFIG_MAX_MEM_MAPPED) + size = CONFIG_MAX_MEM_MAPPED - base; +#endif + if (set_ddr_laws(base, size, law_memctl) < 0) { + printf("%s: ERROR (ctrl #%d, TRGT ID=%x)\n", __func__, ctrl_num, + law_memctl); + return ; + } + debug("setup ddr law base = 0x%llx, size 0x%llx, TRGT_ID 0x%x\n", + base, size, law_memctl); +} + +__attribute__((weak, alias("__fsl_ddr_set_lawbar"))) void +fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params, + unsigned int memctl_interleaved, + unsigned int ctrl_num); +#endif + +void fsl_ddr_set_intl3r(const unsigned int granule_size) +{ +#ifdef CONFIG_E6500 + u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004); + *mcintl3r = 0x80000000 | (granule_size & 0x1f); + debug("Enable MCINTL3R with granule size 0x%x\n", granule_size); +#endif +} + +u32 fsl_ddr_get_intl3r(void) +{ + u32 val = 0; +#ifdef CONFIG_E6500 + u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004); + val = *mcintl3r; +#endif + return val; +} + +void board_add_ram_info(int use_default) +{ + struct ccsr_ddr __iomem *ddr = + (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR); + +#if defined(CONFIG_E6500) && (CONFIG_NUM_DDR_CONTROLLERS == 3) + u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004); +#endif +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + uint32_t cs0_config = in_be32(&ddr->cs0_config); +#endif + uint32_t sdram_cfg = in_be32(&ddr->sdram_cfg); + int cas_lat; + +#if CONFIG_NUM_DDR_CONTROLLERS >= 2 + if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) { + ddr = (void __iomem *)CONFIG_SYS_FSL_DDR2_ADDR; + sdram_cfg = in_be32(&ddr->sdram_cfg); + } +#endif +#if CONFIG_NUM_DDR_CONTROLLERS >= 3 + if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) { + ddr = (void __iomem *)CONFIG_SYS_FSL_DDR3_ADDR; + sdram_cfg = in_be32(&ddr->sdram_cfg); + } +#endif + puts(" (DDR"); + switch ((sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) >> + SDRAM_CFG_SDRAM_TYPE_SHIFT) { + case SDRAM_TYPE_DDR1: + puts("1"); + break; + case SDRAM_TYPE_DDR2: + puts("2"); + break; + case SDRAM_TYPE_DDR3: + puts("3"); + break; + default: + puts("?"); + break; + } + + if (sdram_cfg & SDRAM_CFG_32_BE) + puts(", 32-bit"); + else if (sdram_cfg & SDRAM_CFG_16_BE) + puts(", 16-bit"); + else + puts(", 64-bit"); + + /* Calculate CAS latency based on timing cfg values */ + cas_lat = ((in_be32(&ddr->timing_cfg_1) >> 16) & 0xf) + 1; + if ((in_be32(&ddr->timing_cfg_3) >> 12) & 1) + cas_lat += (8 << 1); + printf(", CL=%d", cas_lat >> 1); + if (cas_lat & 0x1) + puts(".5"); + + if (sdram_cfg & SDRAM_CFG_ECC_EN) + puts(", ECC on)"); + else + puts(", ECC off)"); + +#if (CONFIG_NUM_DDR_CONTROLLERS == 3) +#ifdef CONFIG_E6500 + if (*mcintl3r & 0x80000000) { + puts("\n"); + puts(" DDR Controller Interleaving Mode: "); + switch (*mcintl3r & 0x1f) { + case FSL_DDR_3WAY_1KB_INTERLEAVING: + puts("3-way 1KB"); + break; + case FSL_DDR_3WAY_4KB_INTERLEAVING: + puts("3-way 4KB"); + break; + case FSL_DDR_3WAY_8KB_INTERLEAVING: + puts("3-way 8KB"); + break; + default: + puts("3-way UNKNOWN"); + break; + } + } +#endif +#endif +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) + if (cs0_config & 0x20000000) { + puts("\n"); + puts(" DDR Controller Interleaving Mode: "); + + switch ((cs0_config >> 24) & 0xf) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + puts("cache line"); + break; + case FSL_DDR_PAGE_INTERLEAVING: + puts("page"); + break; + case FSL_DDR_BANK_INTERLEAVING: + puts("bank"); + break; + case FSL_DDR_SUPERBANK_INTERLEAVING: + puts("super-bank"); + break; + default: + puts("invalid"); + break; + } + } +#endif + + if ((sdram_cfg >> 8) & 0x7f) { + puts("\n"); + puts(" DDR Chip-Select Interleaving Mode: "); + switch(sdram_cfg >> 8 & 0x7f) { + case FSL_DDR_CS0_CS1_CS2_CS3: + puts("CS0+CS1+CS2+CS3"); + break; + case FSL_DDR_CS0_CS1: + puts("CS0+CS1"); + break; + case FSL_DDR_CS2_CS3: + puts("CS2+CS3"); + break; + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + puts("CS0+CS1 and CS2+CS3"); + break; + default: + puts("invalid"); + break; + } + } +} diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index 4fcdf40fd..dfb2e7fc7 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -5,7 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_FPGA obj-y += fpga.o obj-$(CONFIG_FPGA_SPARTAN2) += spartan2.o obj-$(CONFIG_FPGA_SPARTAN3) += spartan3.o @@ -19,4 +18,3 @@ obj-$(CONFIG_FPGA_ACEX1K) += ACEX1K.o obj-$(CONFIG_FPGA_CYCLON2) += cyclon2.o obj-$(CONFIG_FPGA_STRATIX_II) += stratixII.o endif -endif diff --git a/drivers/gpio/at91_gpio.c b/drivers/gpio/at91_gpio.c index af0978675..8b766665c 100644 --- a/drivers/gpio/at91_gpio.c +++ b/drivers/gpio/at91_gpio.c @@ -14,6 +14,7 @@ #include <asm/sizes.h> #include <asm/arch/hardware.h> #include <asm/arch/at91_pio.h> +#include <asm/arch/gpio.h> static struct at91_port *at91_pio_get_port(unsigned port) { @@ -356,9 +357,6 @@ int at91_get_pio_value(unsigned port, unsigned pin) /* Common GPIO API */ -#define at91_gpio_to_port(gpio) (gpio / 32) -#define at91_gpio_to_pin(gpio) (gpio % 32) - int gpio_request(unsigned gpio, const char *label) { return 0; diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 5280bb3fe..fa3a87570 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -11,21 +11,20 @@ obj-$(CONFIG_DW_I2C) += designware_i2c.o obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o obj-$(CONFIG_I2C_MV) += mv_i2c.o obj-$(CONFIG_I2C_MXS) += mxs_i2c.o -obj-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o -obj-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o -obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o -obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o obj-$(CONFIG_U8500_I2C) += u8500_i2c.o -obj-$(CONFIG_SH_I2C) += sh_i2c.o obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o obj-$(CONFIG_SYS_I2C) += i2c_core.o obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o +obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o +obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o +obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o +obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o -obj-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o +obj-$(CONFIG_SYS_I2C_ZYNQ) += zynq_i2c.o diff --git a/drivers/i2c/designware_i2c.c b/drivers/i2c/designware_i2c.c index c2f06627d..cb2ac04b6 100644 --- a/drivers/i2c/designware_i2c.c +++ b/drivers/i2c/designware_i2c.c @@ -151,7 +151,19 @@ void i2c_init(int speed, int slaveadd) */ static void i2c_setaddress(unsigned int i2c_addr) { + unsigned int enbl; + + /* Disable i2c */ + enbl = readl(&i2c_regs_p->ic_enable); + enbl &= ~IC_ENABLE_0B; + writel(enbl, &i2c_regs_p->ic_enable); + writel(i2c_addr, &i2c_regs_p->ic_tar); + + /* Enable i2c */ + enbl = readl(&i2c_regs_p->ic_enable); + enbl |= IC_ENABLE_0B; + writel(enbl, &i2c_regs_p->ic_enable); } /* @@ -237,9 +249,6 @@ static int i2c_xfer_finish(void) i2c_flush_rxfifo(); - /* Wait for read/write operation to complete on actual memory */ - udelay(10000); - return 0; } diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c index ddeb941fa..fb9fa353d 100644 --- a/drivers/i2c/fti2c010.c +++ b/drivers/i2c/fti2c010.c @@ -13,67 +13,78 @@ #include "fti2c010.h" -#ifndef CONFIG_HARD_I2C -#error "fti2c010: CONFIG_HARD_I2C is not defined" +#ifndef CONFIG_SYS_I2C_SPEED +#define CONFIG_SYS_I2C_SPEED 5000 #endif -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 +#ifndef CONFIG_SYS_I2C_SLAVE +#define CONFIG_SYS_I2C_SLAVE 0 #endif -#ifndef CONFIG_FTI2C010_FREQ -#define CONFIG_FTI2C010_FREQ clk_get_rate("I2C") +#ifndef CONFIG_FTI2C010_CLOCK +#define CONFIG_FTI2C010_CLOCK clk_get_rate("I2C") #endif -/* command timeout */ -#define CFG_CMD_TIMEOUT 10 /* ms */ +#ifndef CONFIG_FTI2C010_TIMEOUT +#define CONFIG_FTI2C010_TIMEOUT 10 /* ms */ +#endif -/* 7-bit chip address + 1-bit read/write */ -#define I2C_RD(chip) ((((chip) << 1) & 0xff) | 1) -#define I2C_WR(chip) (((chip) << 1) & 0xff) +/* 7-bit dev address + 1-bit read/write */ +#define I2C_RD(dev) ((((dev) << 1) & 0xfe) | 1) +#define I2C_WR(dev) (((dev) << 1) & 0xfe) struct fti2c010_chip { - void __iomem *regs; - uint bus; - uint speed; + struct fti2c010_regs *regs; }; static struct fti2c010_chip chip_list[] = { { - .bus = 0, - .regs = (void __iomem *)CONFIG_FTI2C010_BASE, + .regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE, }, -#ifdef CONFIG_I2C_MULTI_BUS -# ifdef CONFIG_FTI2C010_BASE1 +#ifdef CONFIG_FTI2C010_BASE1 { - .bus = 1, - .regs = (void __iomem *)CONFIG_FTI2C010_BASE1, + .regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE1, }, -# endif -# ifdef CONFIG_FTI2C010_BASE2 +#endif +#ifdef CONFIG_FTI2C010_BASE2 { - .bus = 2, - .regs = (void __iomem *)CONFIG_FTI2C010_BASE2, + .regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE2, }, -# endif -# ifdef CONFIG_FTI2C010_BASE3 +#endif +#ifdef CONFIG_FTI2C010_BASE3 { - .bus = 3, - .regs = (void __iomem *)CONFIG_FTI2C010_BASE3, + .regs = (struct fti2c010_regs *)CONFIG_FTI2C010_BASE3, }, -# endif -#endif /* #ifdef CONFIG_I2C_MULTI_BUS */ +#endif }; -static struct fti2c010_chip *curr = chip_list; +static int fti2c010_reset(struct fti2c010_chip *chip) +{ + ulong ts; + int ret = -1; + struct fti2c010_regs *regs = chip->regs; + + writel(CR_I2CRST, ®s->cr); + for (ts = get_timer(0); get_timer(ts) < CONFIG_FTI2C010_TIMEOUT; ) { + if (!(readl(®s->cr) & CR_I2CRST)) { + ret = 0; + break; + } + } -static int fti2c010_wait(uint32_t mask) + if (ret) + printf("fti2c010: reset timeout\n"); + + return ret; +} + +static int fti2c010_wait(struct fti2c010_chip *chip, uint32_t mask) { int ret = -1; uint32_t stat, ts; - struct fti2c010_regs *regs = curr->regs; + struct fti2c010_regs *regs = chip->regs; - for (ts = get_timer(0); get_timer(ts) < CFG_CMD_TIMEOUT; ) { + for (ts = get_timer(0); get_timer(ts) < CONFIG_FTI2C010_TIMEOUT; ) { stat = readl(®s->sr); if ((stat & mask) == mask) { ret = 0; @@ -84,88 +95,124 @@ static int fti2c010_wait(uint32_t mask) return ret; } -/* - * u-boot I2C API - */ +static unsigned int set_i2c_bus_speed(struct fti2c010_chip *chip, + unsigned int speed) +{ + struct fti2c010_regs *regs = chip->regs; + unsigned int clk = CONFIG_FTI2C010_CLOCK; + unsigned int gsr = 0; + unsigned int tsr = 32; + unsigned int div, rate; + + for (div = 0; div < 0x3ffff; ++div) { + /* SCLout = PCLK/(2*(COUNT + 2) + GSR) */ + rate = clk / (2 * (div + 2) + gsr); + if (rate <= speed) + break; + } + + writel(TGSR_GSR(gsr) | TGSR_TSR(tsr), ®s->tgsr); + writel(CDR_DIV(div), ®s->cdr); + + return rate; +} /* * Initialization, must be called once on start up, may be called * repeatedly to change the speed and slave addresses. */ -void i2c_init(int speed, int slaveaddr) +static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr) { - if (speed || !curr->speed) - i2c_set_bus_speed(speed); + struct fti2c010_chip *chip = chip_list + adap->hwadapnr; - /* if slave mode disabled */ - if (!slaveaddr) + if (adap->init_done) return; - /* - * TODO: - * Implement slave mode, but is it really necessary? - */ +#ifdef CONFIG_SYS_I2C_INIT_BOARD + /* Call board specific i2c bus reset routine before accessing the + * environment, which might be in a chip on that bus. For details + * about this problem see doc/I2C_Edge_Conditions. + */ + i2c_init_board(); +#endif + + /* master init */ + + fti2c010_reset(chip); + + set_i2c_bus_speed(chip, speed); + + /* slave init, don't care */ + +#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT + /* Call board specific i2c bus reset routine AFTER the bus has been + * initialized. Use either this callpoint or i2c_init_board; + * which is called before fti2c010_init operations. + * For details about this problem see doc/I2C_Edge_Conditions. + */ + i2c_board_late_init(); +#endif } /* * Probe the given I2C chip address. Returns 0 if a chip responded, * not 0 on failure. */ -int i2c_probe(uchar chip) +static int fti2c010_probe(struct i2c_adapter *adap, u8 dev) { + struct fti2c010_chip *chip = chip_list + adap->hwadapnr; + struct fti2c010_regs *regs = chip->regs; int ret; - struct fti2c010_regs *regs = curr->regs; - - i2c_init(0, 0); /* 1. Select slave device (7bits Address + 1bit R/W) */ - writel(I2C_WR(chip), ®s->dr); + writel(I2C_WR(dev), ®s->dr); writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; /* 2. Select device register */ writel(0, ®s->dr); writel(CR_ENABLE | CR_TBEN, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); return ret; } -/* - * Read/Write interface: - * chip: I2C chip address, range 0..127 - * addr: Memory (register) address within the chip - * alen: Number of bytes to use for addr (typically 1, 2 for larger - * memories, 0 for register type devices with only one - * register) - * buffer: Where to read/write the data - * len: How many bytes to read/write - * - * Returns: 0 on success, not 0 on failure - */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) +static void to_i2c_addr(u8 *buf, uint32_t addr, int alen) +{ + int i, shift; + + if (!buf || alen <= 0) + return; + + /* MSB first */ + i = 0; + shift = (alen - 1) * 8; + while (alen-- > 0) { + buf[i] = (u8)(addr >> shift); + shift -= 8; + } +} + +static int fti2c010_read(struct i2c_adapter *adap, + u8 dev, uint addr, int alen, uchar *buf, int len) { + struct fti2c010_chip *chip = chip_list + adap->hwadapnr; + struct fti2c010_regs *regs = chip->regs; int ret, pos; uchar paddr[4]; - struct fti2c010_regs *regs = curr->regs; - i2c_init(0, 0); - - paddr[0] = (addr >> 0) & 0xFF; - paddr[1] = (addr >> 8) & 0xFF; - paddr[2] = (addr >> 16) & 0xFF; - paddr[3] = (addr >> 24) & 0xFF; + to_i2c_addr(paddr, addr, alen); /* * Phase A. Set register address */ /* A.1 Select slave device (7bits Address + 1bit R/W) */ - writel(I2C_WR(chip), ®s->dr); + writel(I2C_WR(dev), ®s->dr); writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; @@ -175,7 +222,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) writel(paddr[pos], ®s->dr); writel(ctrl, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; } @@ -185,9 +232,9 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) */ /* B.1 Select slave device (7bits Address + 1bit R/W) */ - writel(I2C_RD(chip), ®s->dr); + writel(I2C_RD(dev), ®s->dr); writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; @@ -201,7 +248,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) stat |= SR_ACK; } writel(ctrl, ®s->cr); - ret = fti2c010_wait(stat); + ret = fti2c010_wait(chip, stat); if (ret) break; buf[pos] = (uchar)(readl(®s->dr) & 0xFF); @@ -210,39 +257,24 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) return ret; } -/* - * Read/Write interface: - * chip: I2C chip address, range 0..127 - * addr: Memory (register) address within the chip - * alen: Number of bytes to use for addr (typically 1, 2 for larger - * memories, 0 for register type devices with only one - * register) - * buffer: Where to read/write the data - * len: How many bytes to read/write - * - * Returns: 0 on success, not 0 on failure - */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) +static int fti2c010_write(struct i2c_adapter *adap, + u8 dev, uint addr, int alen, u8 *buf, int len) { + struct fti2c010_chip *chip = chip_list + adap->hwadapnr; + struct fti2c010_regs *regs = chip->regs; int ret, pos; uchar paddr[4]; - struct fti2c010_regs *regs = curr->regs; - i2c_init(0, 0); - - paddr[0] = (addr >> 0) & 0xFF; - paddr[1] = (addr >> 8) & 0xFF; - paddr[2] = (addr >> 16) & 0xFF; - paddr[3] = (addr >> 24) & 0xFF; + to_i2c_addr(paddr, addr, alen); /* * Phase A. Set register address * * A.1 Select slave device (7bits Address + 1bit R/W) */ - writel(I2C_WR(chip), ®s->dr); + writel(I2C_WR(dev), ®s->dr); writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; @@ -252,7 +284,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) writel(paddr[pos], ®s->dr); writel(ctrl, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) return ret; } @@ -267,7 +299,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) ctrl |= CR_STOP; writel(buf[pos], ®s->dr); writel(ctrl, ®s->cr); - ret = fti2c010_wait(SR_DT); + ret = fti2c010_wait(chip, SR_DT); if (ret) break; } @@ -275,94 +307,40 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) return ret; } -/* - * Functions for setting the current I2C bus and its speed - */ -#ifdef CONFIG_I2C_MULTI_BUS - -/* - * i2c_set_bus_num: - * - * Change the active I2C bus. Subsequent read/write calls will - * go to this one. - * - * bus - bus index, zero based - * - * Returns: 0 on success, not 0 on failure - */ -int i2c_set_bus_num(uint bus) -{ - if (bus >= ARRAY_SIZE(chip_list)) - return -1; - curr = chip_list + bus; - i2c_init(0, 0); - return 0; -} - -/* - * i2c_get_bus_num: - * - * Returns index of currently active I2C bus. Zero-based. - */ - -uint i2c_get_bus_num(void) -{ - return curr->bus; -} - -#endif /* #ifdef CONFIG_I2C_MULTI_BUS */ - -/* - * i2c_set_bus_speed: - * - * Change the speed of the active I2C bus - * - * speed - bus speed in Hz - * - * Returns: 0 on success, not 0 on failure - */ -int i2c_set_bus_speed(uint speed) +static unsigned int fti2c010_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - struct fti2c010_regs *regs = curr->regs; - uint clk = CONFIG_FTI2C010_FREQ; - uint gsr = 0, tsr = 32; - uint spd, div; - - if (!speed) - speed = CONFIG_SYS_I2C_SPEED; - - for (div = 0; div < 0x3ffff; ++div) { - /* SCLout = PCLK/(2*(COUNT + 2) + GSR) */ - spd = clk / (2 * (div + 2) + gsr); - if (spd <= speed) - break; - } - - if (curr->speed == spd) - return 0; - - writel(CR_I2CRST, ®s->cr); - mdelay(100); - if (readl(®s->cr) & CR_I2CRST) { - printf("fti2c010: reset timeout\n"); - return -1; - } + struct fti2c010_chip *chip = chip_list + adap->hwadapnr; + int ret; - curr->speed = spd; + fti2c010_reset(chip); + ret = set_i2c_bus_speed(chip, speed); - writel(TGSR_GSR(gsr) | TGSR_TSR(tsr), ®s->tgsr); - writel(CDR_DIV(div), ®s->cdr); - - return 0; + return ret; } /* - * i2c_get_bus_speed: - * - * Returns speed of currently active I2C bus in Hz + * Register i2c adapters */ - -uint i2c_get_bus_speed(void) -{ - return curr->speed; -} +U_BOOT_I2C_ADAP_COMPLETE(i2c_0, fti2c010_init, fti2c010_probe, fti2c010_read, + fti2c010_write, fti2c010_set_bus_speed, + CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, + 0) +#ifdef CONFIG_FTI2C010_BASE1 +U_BOOT_I2C_ADAP_COMPLETE(i2c_1, fti2c010_init, fti2c010_probe, fti2c010_read, + fti2c010_write, fti2c010_set_bus_speed, + CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, + 1) +#endif +#ifdef CONFIG_FTI2C010_BASE2 +U_BOOT_I2C_ADAP_COMPLETE(i2c_2, fti2c010_init, fti2c010_probe, fti2c010_read, + fti2c010_write, fti2c010_set_bus_speed, + CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, + 2) +#endif +#ifdef CONFIG_FTI2C010_BASE3 +U_BOOT_I2C_ADAP_COMPLETE(i2c_3, fti2c010_init, fti2c010_probe, fti2c010_read, + fti2c010_write, fti2c010_set_bus_speed, + CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, + 3) +#endif diff --git a/drivers/i2c/mxs_i2c.c b/drivers/i2c/mxs_i2c.c index 46106b771..a298c95e1 100644 --- a/drivers/i2c/mxs_i2c.c +++ b/drivers/i2c/mxs_i2c.c @@ -150,6 +150,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) { struct mxs_i2c_regs *i2c_regs = (struct mxs_i2c_regs *)MXS_I2C0_BASE; uint32_t tmp = 0; + int timeout = MXS_I2C_MAX_TIMEOUT; int ret; int i; @@ -169,9 +170,17 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) for (i = 0; i < len; i++) { if (!(i & 3)) { - while (readl(&i2c_regs->hw_i2c_queuestat) & - I2C_QUEUESTAT_RD_QUEUE_EMPTY) - ; + while (--timeout) { + tmp = readl(&i2c_regs->hw_i2c_queuestat); + if (!(tmp & I2C_QUEUESTAT_RD_QUEUE_EMPTY)) + break; + } + + if (!timeout) { + debug("MXS I2C: Failed receiving data!\n"); + return -ETIMEDOUT; + } + tmp = readl(&i2c_regs->hw_i2c_queuedata); } buffer[i] = tmp & 0xff; diff --git a/drivers/i2c/omap1510_i2c.c b/drivers/i2c/omap1510_i2c.c deleted file mode 100644 index f91ee8884..000000000 --- a/drivers/i2c/omap1510_i2c.c +++ /dev/null @@ -1,277 +0,0 @@ -/* - * Basic I2C functions - * - * Copyright (c) 2003 Texas Instruments - * - * This package is free software; you can redistribute it and/or - * modify it under the terms of the license found in the file - * named COPYING that should have accompanied this file. - * - * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR - * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED - * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. - * - * Author: Jian Zhang jzhang@ti.com, Texas Instruments - * - * Copyright (c) 2003 Wolfgang Denk, wd@denx.de - * Rewritten to fit into the current U-Boot framework - * - */ - -#include <common.h> - -static void wait_for_bb (void); -static u16 wait_for_pin (void); - -void i2c_init (int speed, int slaveadd) -{ - u16 scl; - - if (inw (I2C_CON) & I2C_CON_EN) { - outw (0, I2C_CON); - udelay (5000); - } - - /* 12MHz I2C module clock */ - outw (0, I2C_PSC); - outw (I2C_CON_EN, I2C_CON); - outw (0, I2C_SYSTEST); - /* have to enable intrrupts or OMAP i2c module doesn't work */ - outw (I2C_IE_XRDY_IE | I2C_IE_RRDY_IE | I2C_IE_ARDY_IE | - I2C_IE_NACK_IE | I2C_IE_AL_IE, I2C_IE); - scl = (12000000 / 2) / speed - 6; - outw (scl, I2C_SCLL); - outw (scl, I2C_SCLH); - /* own address */ - outw (slaveadd, I2C_OA); - outw (0, I2C_CNT); - udelay (1000); -} - -static int i2c_read_byte (u8 devaddr, u8 regoffset, u8 * value) -{ - int i2c_error = 0; - u16 status; - - /* wait until bus not busy */ - wait_for_bb (); - - /* one byte only */ - outw (1, I2C_CNT); - /* set slave address */ - outw (devaddr, I2C_SA); - /* no stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX, I2C_CON); - - status = wait_for_pin (); - - if (status & I2C_STAT_XRDY) { - /* Important: have to use byte access */ - *(volatile u8 *) (I2C_DATA) = regoffset; - udelay (20000); - if (inw (I2C_STAT) & I2C_STAT_NACK) { - i2c_error = 1; - } - } else { - i2c_error = 1; - } - - if (!i2c_error) { - /* free bus, otherwise we can't use a combined transction */ - outw (0, I2C_CON); - while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (10000); - /* Have to clear pending interrupt to clear I2C_STAT */ - inw (I2C_IV); - } - - wait_for_bb (); - /* set slave address */ - outw (devaddr, I2C_SA); - /* read one byte from slave */ - outw (1, I2C_CNT); - /* need stop bit here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, - I2C_CON); - - status = wait_for_pin (); - if (status & I2C_STAT_RRDY) { - *value = inw (I2C_DATA); - udelay (20000); - } else { - i2c_error = 1; - } - - if (!i2c_error) { - outw (I2C_CON_EN, I2C_CON); - while (inw (I2C_STAT) - || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (10000); - inw (I2C_IV); - } - } - } - - return i2c_error; -} - -static int i2c_write_byte (u8 devaddr, u8 regoffset, u8 value) -{ - int i2c_error = 0; - u16 status; - - /* wait until bus not busy */ - wait_for_bb (); - - /* two bytes */ - outw (2, I2C_CNT); - /* set slave address */ - outw (devaddr, I2C_SA); - /* stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX | - I2C_CON_STP, I2C_CON); - - /* wait until state change */ - status = wait_for_pin (); - - if (status & I2C_STAT_XRDY) { - /* send out two bytes */ - outw ((value << 8) + regoffset, I2C_DATA); - /* must have enough delay to allow BB bit to go low */ - udelay (30000); - if (inw (I2C_STAT) & I2C_STAT_NACK) { - i2c_error = 1; - } - } else { - i2c_error = 1; - } - - if (!i2c_error) { - outw (I2C_CON_EN, I2C_CON); - while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (1000); - /* have to read to clear intrrupt */ - inw (I2C_IV); - } - } - - return i2c_error; -} - -int i2c_probe (uchar chip) -{ - int res = 1; - - if (chip == inw (I2C_OA)) { - return res; - } - - /* wait until bus not busy */ - wait_for_bb (); - - /* try to read one byte */ - outw (1, I2C_CNT); - /* set slave address */ - outw (chip, I2C_SA); - /* stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, I2C_CON); - /* enough delay for the NACK bit set */ - udelay (2000); - if (!(inw (I2C_STAT) & I2C_STAT_NACK)) { - res = 0; - } else { - outw (inw (I2C_CON) | I2C_CON_STP, I2C_CON); - udelay (20); - wait_for_bb (); - } - - return res; -} - -int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - int i; - - if (alen > 1) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if (addr + len > 256) { - printf ("I2C read: address out of range\n"); - return 1; - } - - for (i = 0; i < len; i++) { - if (i2c_read_byte (chip, addr + i, &buffer[i])) { - printf ("I2C read: I/O error\n"); - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - return 1; - } - } - - return 0; -} - -int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - int i; - - if (alen > 1) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if (addr + len > 256) { - printf ("I2C read: address out of range\n"); - return 1; - } - - for (i = 0; i < len; i++) { - if (i2c_write_byte (chip, addr + i, buffer[i])) { - printf ("I2C read: I/O error\n"); - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - return 1; - } - } - - return 0; -} - -static void wait_for_bb (void) -{ - int timeout = 10; - - while ((inw (I2C_STAT) & I2C_STAT_BB) && timeout--) { - inw (I2C_IV); - udelay (1000); - } - - if (timeout <= 0) { - printf ("timed out in wait_for_bb: I2C_STAT=%x\n", - inw (I2C_STAT)); - } -} - -static u16 wait_for_pin (void) -{ - u16 status, iv; - int timeout = 10; - - do { - udelay (1000); - status = inw (I2C_STAT); - iv = inw (I2C_IV); - } while (!iv && - !(status & - (I2C_STAT_ROVR | I2C_STAT_XUDF | I2C_STAT_XRDY | - I2C_STAT_RRDY | I2C_STAT_ARDY | I2C_STAT_NACK | - I2C_STAT_AL)) && timeout--); - - if (timeout <= 0) { - printf ("timed out in wait_for_pin: I2C_STAT=%x\n", - inw (I2C_STAT)); - } - - return status; -} diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index ef38d7172..c7840049b 100644 --- a/drivers/i2c/omap24xx_i2c.c +++ b/drivers/i2c/omap24xx_i2c.c @@ -35,6 +35,7 @@ */ #include <common.h> +#include <i2c.h> #include <asm/arch/i2c.h> #include <asm/io.h> @@ -48,22 +49,14 @@ DECLARE_GLOBAL_DATA_PTR; /* Absolutely safe for status update at 100 kHz I2C: */ #define I2C_WAIT 200 -static int wait_for_bb(void); -static u16 wait_for_event(void); -static void flush_fifo(void); +static int wait_for_bb(struct i2c_adapter *adap); +static struct i2c *omap24_get_base(struct i2c_adapter *adap); +static u16 wait_for_event(struct i2c_adapter *adap); +static void flush_fifo(struct i2c_adapter *adap); -/* - * For SPL boot some boards need i2c before SDRAM is initialised so force - * variables to live in SRAM - */ -static struct i2c __attribute__((section (".data"))) *i2c_base = - (struct i2c *)I2C_DEFAULT_BASE; -static unsigned int __attribute__((section (".data"))) bus_initialized[I2C_BUS_MAX] = - { [0 ... (I2C_BUS_MAX-1)] = 0 }; -static unsigned int __attribute__((section (".data"))) current_bus = 0; - -void i2c_init(int speed, int slaveadd) +static void omap24_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { + struct i2c *i2c_base = omap24_get_base(adap); int psc, fsscll, fssclh; int hsscll = 0, hssclh = 0; u32 scll, sclh; @@ -163,16 +156,14 @@ void i2c_init(int speed, int slaveadd) I2C_IE_NACK_IE | I2C_IE_AL_IE, &i2c_base->ie); #endif udelay(1000); - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); - writew(0, &i2c_base->cnt); - - if (gd->flags & GD_FLG_RELOC) - bus_initialized[current_bus] = 1; } -static void flush_fifo(void) -{ u16 stat; +static void flush_fifo(struct i2c_adapter *adap) +{ + struct i2c *i2c_base = omap24_get_base(adap); + u16 stat; /* note: if you try and read data when its not there or ready * you get a bus error @@ -192,8 +183,9 @@ static void flush_fifo(void) * i2c_probe: Use write access. Allows to identify addresses that are * write-only (like the config register of dual-port EEPROMs) */ -int i2c_probe(uchar chip) +static int omap24_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int res = 1; /* default = fail */ @@ -201,18 +193,16 @@ int i2c_probe(uchar chip) return res; /* Wait until bus is free */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return res; /* No data transfer, slave addr only */ - writew(0, &i2c_base->cnt); - /* Set slave address */ writew(chip, &i2c_base->sa); /* Stop bit needed here */ writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX | I2C_CON_STP, &i2c_base->con); - status = wait_for_event(); + status = wait_for_event(adap); if ((status & ~I2C_STAT_XRDY) == 0 || (status & I2C_STAT_AL)) { /* @@ -223,7 +213,7 @@ int i2c_probe(uchar chip) */ if (status == I2C_STAT_XRDY) printf("i2c_probe: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto pr_exit; } @@ -239,9 +229,8 @@ int i2c_probe(uchar chip) I2C_CON_STP, &i2c_base->con); /* STP */ } pr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); - writew(0, &i2c_base->cnt); return res; } @@ -258,8 +247,10 @@ pr_exit: * or that do not need a register address at all (such as some clock * distributors). */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i2c_error = 0; u16 status; @@ -287,7 +278,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Zero, one or two bytes reg address (offset) */ @@ -308,12 +299,12 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) #endif /* Send register offset */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (addr phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -348,7 +339,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) /* Receive data */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* * Try to identify bus that is not padconf'd for I2C. This * state could be left over from previous transactions if @@ -357,7 +348,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (data phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -375,15 +366,16 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } rd_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); - writew(0, &i2c_base->cnt); return i2c_error; } /* i2c_write: Address (reg offset) may be 0, 1 or 2 bytes long. */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i; u16 status; int i2c_error = 0; @@ -415,7 +407,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Start address phase - will write regoffset + len bytes data */ @@ -428,12 +420,12 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) while (alen) { /* Must write reg offset (one or two bytes) */ - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_write: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto wr_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -455,7 +447,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Address phase is over, now write data */ for (i = 0; i < len; i++) { - status = wait_for_event(); + status = wait_for_event(adap); if (status == 0 || status & I2C_STAT_NACK) { i2c_error = 1; printf("i2c_write: error waiting for data ACK (status=0x%x)\n", @@ -474,9 +466,8 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } wr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); - writew(0, &i2c_base->cnt); return i2c_error; } @@ -484,8 +475,9 @@ wr_exit: * Wait for the bus to be free by checking the Bus Busy (BB) * bit to become clear */ -static int wait_for_bb(void) +static int wait_for_bb(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); int timeout = I2C_TIMEOUT; u16 stat; @@ -514,8 +506,9 @@ static int wait_for_bb(void) * Wait for the I2C controller to complete current action * and update status */ -static u16 wait_for_event(void) +static u16 wait_for_event(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int timeout = I2C_TIMEOUT; @@ -540,7 +533,7 @@ static u16 wait_for_event(void) * not been configured for I2C, and/or pull-ups are missing. */ printf("Check if pads/pull-ups of bus %d are properly configured\n", - current_bus); + adap->hwadapnr); writew(0xFFFF, &i2c_base->stat); status = 0; } @@ -548,48 +541,93 @@ static u16 wait_for_event(void) return status; } -int i2c_set_bus_num(unsigned int bus) +static struct i2c *omap24_get_base(struct i2c_adapter *adap) { - if (bus >= I2C_BUS_MAX) { - printf("Bad bus: %x\n", bus); - return -1; - } - - switch (bus) { - default: - bus = 0; /* Fall through */ + switch (adap->hwadapnr) { case 0: - i2c_base = (struct i2c *)I2C_BASE1; + return (struct i2c *)I2C_BASE1; break; case 1: - i2c_base = (struct i2c *)I2C_BASE2; + return (struct i2c *)I2C_BASE2; break; #if (I2C_BUS_MAX > 2) case 2: - i2c_base = (struct i2c *)I2C_BASE3; + return (struct i2c *)I2C_BASE3; break; #if (I2C_BUS_MAX > 3) case 3: - i2c_base = (struct i2c *)I2C_BASE4; + return (struct i2c *)I2C_BASE4; break; #if (I2C_BUS_MAX > 4) case 4: - i2c_base = (struct i2c *)I2C_BASE5; + return (struct i2c *)I2C_BASE5; break; #endif #endif #endif + default: + printf("wrong hwadapnr: %d\n", adap->hwadapnr); + break; } + return NULL; +} + +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED1) +#define CONFIG_SYS_OMAP24_I2C_SPEED1 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE1) +#define CONFIG_SYS_OMAP24_I2C_SLAVE1 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - current_bus = bus; +U_BOOT_I2C_ADAP_COMPLETE(omap24_0, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED, + CONFIG_SYS_OMAP24_I2C_SLAVE, + 0) +U_BOOT_I2C_ADAP_COMPLETE(omap24_1, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED1, + CONFIG_SYS_OMAP24_I2C_SLAVE1, + 1) +#if (I2C_BUS_MAX > 2) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED2) +#define CONFIG_SYS_OMAP24_I2C_SPEED2 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE2) +#define CONFIG_SYS_OMAP24_I2C_SLAVE2 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - if (!bus_initialized[current_bus]) - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +U_BOOT_I2C_ADAP_COMPLETE(omap24_2, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED2, + CONFIG_SYS_OMAP24_I2C_SLAVE2, + 2) +#if (I2C_BUS_MAX > 3) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED3) +#define CONFIG_SYS_OMAP24_I2C_SPEED3 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE3) +#define CONFIG_SYS_OMAP24_I2C_SLAVE3 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - return 0; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_3, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED3, + CONFIG_SYS_OMAP24_I2C_SLAVE3, + 3) +#if (I2C_BUS_MAX > 4) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED4) +#define CONFIG_SYS_OMAP24_I2C_SPEED4 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE4) +#define CONFIG_SYS_OMAP24_I2C_SLAVE4 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif -int i2c_get_bus_num(void) -{ - return (int) current_bus; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_4, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED4, + CONFIG_SYS_OMAP24_I2C_SLAVE4, + 4) +#endif +#endif +#endif diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c index f77a9d1a1..fd328f054 100644 --- a/drivers/i2c/s3c24x0_i2c.c +++ b/drivers/i2c/s3c24x0_i2c.c @@ -23,8 +23,6 @@ #include <i2c.h> #include "s3c24x0_i2c.h" -#ifdef CONFIG_HARD_I2C - #define I2C_WRITE 0 #define I2C_READ 1 @@ -127,7 +125,6 @@ * For SPL boot some boards need i2c before SDRAM is initialised so force * variables to live in SRAM */ -static unsigned int g_current_bus __attribute__((section(".data"))); static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM] __attribute__((section(".data"))); @@ -254,17 +251,17 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c) writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon); } -static struct s3c24x0_i2c *get_base_i2c(void) +static struct s3c24x0_i2c *get_base_i2c(int bus) { #ifdef CONFIG_EXYNOS4 struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c() + (EXYNOS4_I2C_SPACING - * g_current_bus)); + * bus)); return i2c; #elif defined CONFIG_EXYNOS5 struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c() + (EXYNOS5_I2C_SPACING - * g_current_bus)); + * bus)); return i2c; #else return s3c24x0_get_base_i2c(); @@ -298,7 +295,6 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd) writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat); } -#ifdef CONFIG_I2C_MULTI_BUS static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus) { struct exynos5_hsi2c *hsregs = i2c_bus->hsregs; @@ -307,8 +303,10 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus) unsigned int i = 0, utemp0 = 0, utemp1 = 0; unsigned int t_ftl_cycle; -#if defined CONFIG_EXYNOS5 +#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) clkin = get_i2c_clk(); +#else + clkin = get_PCLK(); #endif /* FPCLK / FI2C = * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE @@ -330,7 +328,6 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus) } return -1; } -#endif static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus) { @@ -401,49 +398,18 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus) hsi2c_ch_init(i2c_bus); } -/* - * MULTI BUS I2C support - */ - -#ifdef CONFIG_I2C_MULTI_BUS -int i2c_set_bus_num(unsigned int bus) -{ - struct s3c24x0_i2c_bus *i2c_bus; - - i2c_bus = get_bus(bus); - if (!i2c_bus) - return -1; - g_current_bus = bus; - - if (i2c_bus->is_highspeed) { - if (hsi2c_get_clk_details(i2c_bus)) - return -1; - hsi2c_ch_init(i2c_bus); - } else { - i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency, - CONFIG_SYS_I2C_SLAVE); - } - - return 0; -} - -unsigned int i2c_get_bus_num(void) -{ - return g_current_bus; -} -#endif - -void i2c_init(int speed, int slaveadd) +static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { struct s3c24x0_i2c *i2c; + struct s3c24x0_i2c_bus *bus; + #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); #endif ulong start_time = get_timer(0); /* By default i2c channel 0 is the current bus */ - g_current_bus = 0; - i2c = get_base_i2c(); + i2c = get_base_i2c(adap->hwadapnr); /* * In case the previous transfer is still going, wait to give it a @@ -505,6 +471,10 @@ void i2c_init(int speed, int slaveadd) } #endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */ i2c_ch_init(i2c, speed, slaveadd); + + bus = &i2c_bus[adap->hwadapnr]; + bus->active = true; + bus->regs = i2c; } /* @@ -728,6 +698,40 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c, return rv; } +static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) +{ + struct s3c24x0_i2c_bus *i2c_bus; + + i2c_bus = get_bus(adap->hwadapnr); + if (!i2c_bus) + return -1; + + i2c_bus->clock_frequency = speed; + + if (i2c_bus->is_highspeed) { + if (hsi2c_get_clk_details(i2c_bus)) + return -1; + hsi2c_ch_init(i2c_bus); + } else { + i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency, + CONFIG_SYS_I2C_S3C24X0_SLAVE); + } + + return 0; +} + +#ifdef CONFIG_EXYNOS5 +static void exynos_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) +{ + /* This will override the speed selected in the fdt for that port */ + debug("i2c_init(speed=%u, slaveaddr=0x%x)\n", speed, slaveaddr); + if (i2c_set_bus_speed(speed)) + printf("i2c_init: failed to init bus %d for speed = %d\n", + adap->hwadapnr, speed); +} +#endif + /* * cmd_type is 0 for write, 1 for read. * @@ -840,13 +844,13 @@ bailout: return result; } -int i2c_probe(uchar chip) +static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip) { struct s3c24x0_i2c_bus *i2c_bus; uchar buf[1]; int ret; - i2c_bus = get_bus(g_current_bus); + i2c_bus = get_bus(adap->hwadapnr); if (!i2c_bus) return -1; buf[0] = 0; @@ -864,11 +868,11 @@ int i2c_probe(uchar chip) I2C_READ, chip << 1, 0, 0, buf, 1); } - return ret != I2C_OK; } -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { struct s3c24x0_i2c_bus *i2c_bus; uchar xaddr[4]; @@ -902,7 +906,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); #endif - i2c_bus = get_bus(g_current_bus); + i2c_bus = get_bus(adap->hwadapnr); if (!i2c_bus) return -1; @@ -922,7 +926,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) return 0; } -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { struct s3c24x0_i2c_bus *i2c_bus; uchar xaddr[4]; @@ -955,7 +960,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); #endif - i2c_bus = get_bus(g_current_bus); + i2c_bus = get_bus(adap->hwadapnr); if (!i2c_bus) return -1; @@ -1001,8 +1006,8 @@ static void process_nodes(const void *blob, int node_list[], int count, bus->id = pinmux_decode_periph_id(blob, node); bus->clock_frequency = fdtdec_get_int(blob, node, - "clock-frequency", - CONFIG_SYS_I2C_SPEED); + "clock-frequency", + CONFIG_SYS_I2C_S3C24X0_SPEED); bus->node = node; bus->bus_num = i; exynos_pinmux_config(bus->id, 0); @@ -1044,7 +1049,6 @@ int i2c_get_bus_num_fdt(int node) return -1; } -#ifdef CONFIG_I2C_MULTI_BUS int i2c_reset_port_fdt(const void *blob, int node) { struct s3c24x0_i2c_bus *i2c_bus; @@ -1068,12 +1072,178 @@ int i2c_reset_port_fdt(const void *blob, int node) hsi2c_ch_init(i2c_bus); } else { i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency, - CONFIG_SYS_I2C_SLAVE); + CONFIG_SYS_I2C_S3C24X0_SLAVE); } return 0; } #endif -#endif -#endif /* CONFIG_HARD_I2C */ +/* + * Register s3c24x0 i2c adapters + */ +#if defined(CONFIG_EXYNOS5420) +U_BOOT_I2C_ADAP_COMPLETE(i2c00, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) +U_BOOT_I2C_ADAP_COMPLETE(i2c01, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) +U_BOOT_I2C_ADAP_COMPLETE(i2c02, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) +U_BOOT_I2C_ADAP_COMPLETE(i2c03, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) +U_BOOT_I2C_ADAP_COMPLETE(i2c04, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) +U_BOOT_I2C_ADAP_COMPLETE(i2c05, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) +U_BOOT_I2C_ADAP_COMPLETE(i2c06, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) +U_BOOT_I2C_ADAP_COMPLETE(i2c07, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) +U_BOOT_I2C_ADAP_COMPLETE(i2c08, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) +U_BOOT_I2C_ADAP_COMPLETE(i2c09, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 9) +U_BOOT_I2C_ADAP_COMPLETE(i2c10, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 10) +#elif defined(CONFIG_EXYNOS5250) +U_BOOT_I2C_ADAP_COMPLETE(i2c00, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) +U_BOOT_I2C_ADAP_COMPLETE(i2c01, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) +U_BOOT_I2C_ADAP_COMPLETE(i2c02, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) +U_BOOT_I2C_ADAP_COMPLETE(i2c03, exynos_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) +U_BOOT_I2C_ADAP_COMPLETE(i2c04, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) +U_BOOT_I2C_ADAP_COMPLETE(i2c05, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) +U_BOOT_I2C_ADAP_COMPLETE(i2c06, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) +U_BOOT_I2C_ADAP_COMPLETE(i2c07, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) +U_BOOT_I2C_ADAP_COMPLETE(i2c08, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) +U_BOOT_I2C_ADAP_COMPLETE(i2c09, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 9) +U_BOOT_I2C_ADAP_COMPLETE(s3c10, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 10) +#elif defined(CONFIG_EXYNOS4) +U_BOOT_I2C_ADAP_COMPLETE(i2c00, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) +U_BOOT_I2C_ADAP_COMPLETE(i2c01, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) +U_BOOT_I2C_ADAP_COMPLETE(i2c02, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) +U_BOOT_I2C_ADAP_COMPLETE(i2c03, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) +U_BOOT_I2C_ADAP_COMPLETE(i2c04, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) +U_BOOT_I2C_ADAP_COMPLETE(i2c05, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) +U_BOOT_I2C_ADAP_COMPLETE(i2c06, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) +U_BOOT_I2C_ADAP_COMPLETE(i2c07, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) +U_BOOT_I2C_ADAP_COMPLETE(i2c08, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) +#else +U_BOOT_I2C_ADAP_COMPLETE(s3c0, s3c24x0_i2c_init, s3c24x0_i2c_probe, + s3c24x0_i2c_read, s3c24x0_i2c_write, + s3c24x0_i2c_set_bus_speed, + CONFIG_SYS_I2C_S3C24X0_SPEED, + CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) +#endif diff --git a/drivers/i2c/sh_i2c.c b/drivers/i2c/sh_i2c.c index 808202c29..cc1910075 100644 --- a/drivers/i2c/sh_i2c.c +++ b/drivers/i2c/sh_i2c.c @@ -6,6 +6,7 @@ */ #include <common.h> +#include <i2c.h> #include <asm/io.h> DECLARE_GLOBAL_DATA_PTR; @@ -22,8 +23,6 @@ struct sh_i2c { }; #undef ureg -static struct sh_i2c *base; - /* ICCR */ #define SH_I2C_ICCR_ICE (1 << 7) #define SH_I2C_ICCR_RACK (1 << 6) @@ -43,202 +42,165 @@ static struct sh_i2c *base; #define SH_I2C_ICIC_ICCHB8 (1 << 6) #endif +static const struct sh_i2c *i2c_dev[CONFIG_SYS_I2C_SH_NUM_CONTROLLERS] = { + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE0, +#ifdef CONFIG_SYS_I2C_SH_BASE1 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE1, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE2 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE2, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE3 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE3, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE4 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE4, +#endif +}; + static u16 iccl, icch; #define IRQ_WAIT 1000 -static void irq_dte(struct sh_i2c *base) +static void sh_irq_dte(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (SH_IC_DTE & readb(&base->icsr)) + for (i = 0; i < IRQ_WAIT; i++) { + if (SH_IC_DTE & readb(&dev->icsr)) break; udelay(10); } } -static int irq_dte_with_tack(struct sh_i2c *base) +static int sh_irq_dte_with_tack(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (SH_IC_DTE & readb(&base->icsr)) + for (i = 0; i < IRQ_WAIT; i++) { + if (SH_IC_DTE & readb(&dev->icsr)) break; - if (SH_IC_TACK & readb(&base->icsr)) + if (SH_IC_TACK & readb(&dev->icsr)) return -1; udelay(10); } return 0; } -static void irq_busy(struct sh_i2c *base) +static void sh_irq_busy(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (!(SH_IC_BUSY & readb(&base->icsr))) + for (i = 0; i < IRQ_WAIT; i++) { + if (!(SH_IC_BUSY & readb(&dev->icsr))) break; udelay(10); } } -static int i2c_set_addr(struct sh_i2c *base, u8 id, u8 reg, int stop) +static int sh_i2c_set_addr(struct sh_i2c *dev, u8 chip, u8 addr, int stop) { u8 icic = SH_IC_TACK; - clrbits_8(&base->iccr, SH_I2C_ICCR_ICE); - setbits_8(&base->iccr, SH_I2C_ICCR_ICE); + debug("%s: chip: %x, addr: %x iccl: %x, icch %x\n", + __func__, chip, addr, iccl, icch); + clrbits_8(&dev->iccr, SH_I2C_ICCR_ICE); + setbits_8(&dev->iccr, SH_I2C_ICCR_ICE); - writeb(iccl & 0xff, &base->iccl); - writeb(icch & 0xff, &base->icch); + writeb(iccl & 0xff, &dev->iccl); + writeb(icch & 0xff, &dev->icch); #ifdef CONFIG_SH_I2C_8BIT if (iccl > 0xff) icic |= SH_I2C_ICIC_ICCLB8; if (icch > 0xff) icic |= SH_I2C_ICIC_ICCHB8; #endif - writeb(icic, &base->icic); + writeb(icic, &dev->icic); - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &base->iccr); - irq_dte(base); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &dev->iccr); + sh_irq_dte(dev); - clrbits_8(&base->icsr, SH_IC_TACK); - writeb(id << 1, &base->icdr); - if (irq_dte_with_tack(base) != 0) + clrbits_8(&dev->icsr, SH_IC_TACK); + writeb(chip << 1, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) return -1; - writeb(reg, &base->icdr); + writeb(addr, &dev->icdr); if (stop) - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS), &base->iccr); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS), &dev->iccr); - if (irq_dte_with_tack(base) != 0) + if (sh_irq_dte_with_tack(dev) != 0) return -1; return 0; } -static void i2c_finish(struct sh_i2c *base) +static void sh_i2c_finish(struct sh_i2c *dev) { - writeb(0, &base->icsr); - clrbits_8(&base->iccr, SH_I2C_ICCR_ICE); + writeb(0, &dev->icsr); + clrbits_8(&dev->iccr, SH_I2C_ICCR_ICE); } -static int i2c_raw_write(struct sh_i2c *base, u8 id, u8 reg, u8 val) +static int +sh_i2c_raw_write(struct sh_i2c *dev, u8 chip, uint addr, u8 val) { int ret = -1; - if (i2c_set_addr(base, id, reg, 0) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 0) != 0) goto exit0; udelay(10); - writeb(val, &base->icdr); - if (irq_dte_with_tack(base) != 0) + writeb(val, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - writeb((SH_I2C_ICCR_ICE | SH_I2C_ICCR_RTS), &base->iccr); - if (irq_dte_with_tack(base) != 0) + writeb((SH_I2C_ICCR_ICE | SH_I2C_ICCR_RTS), &dev->iccr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - irq_busy(base); + sh_irq_busy(dev); ret = 0; + exit0: - i2c_finish(base); + sh_i2c_finish(dev); return ret; } -static int i2c_raw_read(struct sh_i2c *base, u8 id, u8 reg) +static int sh_i2c_raw_read(struct sh_i2c *dev, u8 chip, u8 addr) { int ret = -1; #if defined(CONFIG_SH73A0) - if (i2c_set_addr(base, id, reg, 0) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 0) != 0) goto exit0; #else - if (i2c_set_addr(base, id, reg, 1) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 1) != 0) goto exit0; udelay(100); #endif - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &base->iccr); - irq_dte(base); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &dev->iccr); + sh_irq_dte(dev); - writeb(id << 1 | 0x01, &base->icdr); - if (irq_dte_with_tack(base) != 0) + writeb(chip << 1 | 0x01, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_SCP), &base->iccr); - if (irq_dte_with_tack(base) != 0) + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_SCP), &dev->iccr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - ret = readb(&base->icdr) & 0xff; + ret = readb(&dev->icdr) & 0xff; + + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RACK), &dev->iccr); + readb(&dev->icdr); /* Dummy read */ + sh_irq_busy(dev); - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RACK), &base->iccr); - readb(&base->icdr); /* Dummy read */ - irq_busy(base); exit0: - i2c_finish(base); + sh_i2c_finish(dev); return ret; } -#ifdef CONFIG_I2C_MULTI_BUS -static unsigned int current_bus; - -/** - * i2c_set_bus_num - change active I2C bus - * @bus: bus index, zero based - * @returns: 0 on success, non-0 on failure - */ -int i2c_set_bus_num(unsigned int bus) -{ - if ((bus < 0) || (bus >= CONFIG_SYS_MAX_I2C_BUS)) { - printf("Bad bus: %d\n", bus); - return -1; - } - - switch (bus) { - case 0: - base = (void *)CONFIG_SH_I2C_BASE0; - break; - case 1: - base = (void *)CONFIG_SH_I2C_BASE1; - break; -#ifdef CONFIG_SH_I2C_BASE2 - case 2: - base = (void *)CONFIG_SH_I2C_BASE2; - break; -#endif -#ifdef CONFIG_SH_I2C_BASE3 - case 3: - base = (void *)CONFIG_SH_I2C_BASE3; - break; -#endif -#ifdef CONFIG_SH_I2C_BASE4 - case 4: - base = (void *)CONFIG_SH_I2C_BASE4; - break; -#endif - default: - return -1; - } - current_bus = bus; - - return 0; -} - -/** - * i2c_get_bus_num - returns index of active I2C bus - */ -unsigned int i2c_get_bus_num(void) -{ - return current_bus; -} -#endif - -#define SH_I2C_ICCL_CALC(clk, date, t_low, t_high) \ - ((clk / rate) * (t_low / t_low + t_high)) -#define SH_I2C_ICCH_CALC(clk, date, t_low, t_high) \ - ((clk / rate) * (t_high / t_low + t_high)) - -void i2c_init(int speed, int slaveaddr) +static void +sh_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { int num, denom, tmp; @@ -246,11 +208,6 @@ void i2c_init(int speed, int slaveaddr) if (!(gd->flags & GD_FLG_RELOC)) return; -#ifdef CONFIG_I2C_MULTI_BUS - current_bus = 0; -#endif - base = (struct sh_i2c *)CONFIG_SH_I2C_BASE0; - /* * Calculate the value for iccl. From the data sheet: * iccl = (p-clock / transfer-rate) * (L / (L + H)) @@ -272,67 +229,78 @@ void i2c_init(int speed, int slaveaddr) icch = (u16)((num/denom) + 1); else icch = (u16)(num/denom); + + debug("clock: %d, speed %d, iccl: %x, icch: %x\n", + CONFIG_SH_I2C_CLOCK, speed, iccl, icch); } -/* - * i2c_read: - Read multiple bytes from an i2c device - * - * The higher level routines take into account that this function is only - * called with len < page length of the device (see configuration file) - * - * @chip: address of the chip which is to be read - * @addr: i2c data address within the chip - * @alen: length of the i2c data address (1..2 bytes) - * @buffer: where to write the data - * @len: how much byte do we want to read - * @return: 0 in case of success - */ -int i2c_read(u8 chip, u32 addr, int alen, u8 *buffer, int len) +static int sh_i2c_read(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, u8 *data, int len) { - int ret; - int i = 0; - for (i = 0 ; i < len ; i++) { - ret = i2c_raw_read(base, chip, addr + i); + int ret, i; + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + + for (i = 0; i < len; i++) { + ret = sh_i2c_raw_read(dev, chip, addr + i); if (ret < 0) return -1; - buffer[i] = ret & 0xff; + + data[i] = ret & 0xff; + debug("%s: data[%d]: %02x\n", __func__, i, data[i]); } + return 0; } -/* - * i2c_write: - Write multiple bytes to an i2c device - * - * The higher level routines take into account that this function is only - * called with len < page length of the device (see configuration file) - * - * @chip: address of the chip which is to be written - * @addr: i2c data address within the chip - * @alen: length of the i2c data address (1..2 bytes) - * @buffer: where to find the data to be written - * @len: how much byte do we want to read - * @return: 0 in case of success - */ -int i2c_write(u8 chip, u32 addr, int alen, u8 *buffer, int len) +static int sh_i2c_write(struct i2c_adapter *adap, uint8_t chip, uint addr, + int alen, u8 *data, int len) { - int i = 0; - for (i = 0; i < len ; i++) - if (i2c_raw_write(base, chip, addr + i, buffer[i]) != 0) + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + int i; + + for (i = 0; i < len; i++) { + debug("%s: data[%d]: %02x\n", __func__, i, data[i]); + if (sh_i2c_raw_write(dev, chip, addr + i, data[i]) != 0) return -1; + } return 0; } -/* - * i2c_probe: - Test if a chip answers for a given i2c address - * - * @chip: address of the chip which is searched for - * @return: 0 if a chip was found, -1 otherwhise - */ -int i2c_probe(u8 chip) +static int +sh_i2c_probe(struct i2c_adapter *adap, u8 dev) { - int ret; + return sh_i2c_read(adap, dev, 0, 0, NULL, 0); +} - ret = i2c_set_addr(base, chip, 0, 1); - i2c_finish(base); - return ret; +static unsigned int sh_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) +{ + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + + sh_i2c_finish(dev); + sh_i2c_init(adap, speed, 0); + + return 0; } + +/* + * Register RCAR i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(sh_0, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED0, 0, 0) +#ifdef CONFIG_SYS_I2C_SH_BASE1 +U_BOOT_I2C_ADAP_COMPLETE(sh_1, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED1, 0, 1) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE2 +U_BOOT_I2C_ADAP_COMPLETE(sh_2, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED2, 0, 2) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE3 +U_BOOT_I2C_ADAP_COMPLETE(sh_3, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED3, 0, 3) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE4 +U_BOOT_I2C_ADAP_COMPLETE(sh_4, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED4, 0, 4) +#endif diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c index 396fea89a..dfea54ae7 100644 --- a/drivers/i2c/soft_i2c.c +++ b/drivers/i2c/soft_i2c.c @@ -25,7 +25,7 @@ #include <asm/io.h> #include <asm/arch/hardware.h> #include <asm/arch/at91_pio.h> -#ifdef CONFIG_AT91_LEGACY +#ifdef CONFIG_ATMEL_LEGACY #include <asm/arch/gpio.h> #endif #endif diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c index 9847cf126..594e5ddeb 100644 --- a/drivers/i2c/tegra_i2c.c +++ b/drivers/i2c/tegra_i2c.c @@ -629,3 +629,8 @@ U_BOOT_I2C_ADAP_COMPLETE(tegra2, tegra_i2c_init, tegra_i2c_probe, U_BOOT_I2C_ADAP_COMPLETE(tegra3, tegra_i2c_init, tegra_i2c_probe, tegra_i2c_read, tegra_i2c_write, tegra_i2c_set_bus_speed, 100000, 0, 3) +#if TEGRA_I2C_NUM_CONTROLLERS > 4 +U_BOOT_I2C_ADAP_COMPLETE(tegra4, tegra_i2c_init, tegra_i2c_probe, + tegra_i2c_read, tegra_i2c_write, + tegra_i2c_set_bus_speed, 100000, 0, 4) +#endif diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c index ce2d23f72..70a9aeafd 100644 --- a/drivers/i2c/zynq_i2c.c +++ b/drivers/i2c/zynq_i2c.c @@ -74,7 +74,8 @@ static struct zynq_i2c_registers *zynq_i2c = (struct zynq_i2c_registers *)ZYNQ_I2C_BASE; /* I2C init called by cmd_i2c when doing 'i2c reset'. */ -void i2c_init(int requested_speed, int slaveadd) +static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed, + int slaveadd) { /* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */ writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) | @@ -151,7 +152,7 @@ static u32 zynq_i2c_wait(u32 mask) * I2C probe called by cmd_i2c when doing 'i2c probe'. * Begin read, nak data byte, end. */ -int i2c_probe(u8 dev) +static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev) { /* Attempt to read a byte */ setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | @@ -170,7 +171,8 @@ int i2c_probe(u8 dev) * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c * Begin write, send address byte(s), begin read, receive data bytes, end. */ -int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) +static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) { u32 status; u32 i = 0; @@ -235,7 +237,8 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c * Begin write, send address byte(s), send data bytes, end. */ -int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) +static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) { u8 *cur_data = data; @@ -275,16 +278,16 @@ int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) return 0; } -int i2c_set_bus_num(unsigned int bus) +static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - /* Only support bus 0 */ - if (bus > 0) - return -1; - return 0; -} + if (speed != 1000000) + return -EINVAL; -unsigned int i2c_get_bus_num(void) -{ - /* Only support bus 0 */ return 0; } + +U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read, + zynq_i2c_write, zynq_i2c_set_bus_speed, + CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE, + 0) diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index d8ff9c641..c77e40a2d 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -20,3 +20,4 @@ obj-$(CONFIG_NS87308) += ns87308.o obj-$(CONFIG_PDSP188x) += pdsp188x.o obj-$(CONFIG_STATUS_LED) += status_led.o obj-$(CONFIG_TWL4030_LED) += twl4030_led.o +obj-$(CONFIG_FSL_IFC) += fsl_ifc.o diff --git a/drivers/misc/cros_ec_spi.c b/drivers/misc/cros_ec_spi.c index 202acf258..2fc911025 100644 --- a/drivers/misc/cros_ec_spi.c +++ b/drivers/misc/cros_ec_spi.c @@ -135,8 +135,7 @@ int cros_ec_spi_decode_fdt(struct cros_ec_dev *dev, const void *blob) */ int cros_ec_spi_init(struct cros_ec_dev *dev, const void *blob) { - dev->spi = spi_setup_slave_fdt(blob, dev->parent_node, - dev->cs, dev->max_frequency, 0); + dev->spi = spi_setup_slave_fdt(blob, dev->parent_node, dev->node); if (!dev->spi) { debug("%s: Could not setup SPI slave\n", __func__); return -1; diff --git a/drivers/misc/fsl_ifc.c b/drivers/misc/fsl_ifc.c new file mode 100644 index 000000000..be6197366 --- /dev/null +++ b/drivers/misc/fsl_ifc.c @@ -0,0 +1,164 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * Author: Dipen Dudhat <dipen.dudhat@freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <fsl_ifc.h> + +void print_ifc_regs(void) +{ + int i, j; + + printf("IFC Controller Registers\n"); + for (i = 0; i < CONFIG_SYS_FSL_IFC_BANK_COUNT; i++) { + printf("CSPR%d:0x%08X\tAMASK%d:0x%08X\tCSOR%d:0x%08X\n", + i, get_ifc_cspr(i), i, get_ifc_amask(i), + i, get_ifc_csor(i)); + for (j = 0; j < 4; j++) + printf("IFC_FTIM%d:0x%08X\n", j, get_ifc_ftim(i, j)); + } +} + +void init_early_memctl_regs(void) +{ +#if defined(CONFIG_SYS_CSPR0) && defined(CONFIG_SYS_CSOR0) + set_ifc_ftim(IFC_CS0, IFC_FTIM0, CONFIG_SYS_CS0_FTIM0); + set_ifc_ftim(IFC_CS0, IFC_FTIM1, CONFIG_SYS_CS0_FTIM1); + set_ifc_ftim(IFC_CS0, IFC_FTIM2, CONFIG_SYS_CS0_FTIM2); + set_ifc_ftim(IFC_CS0, IFC_FTIM3, CONFIG_SYS_CS0_FTIM3); + +#ifndef CONFIG_A003399_NOR_WORKAROUND +#ifdef CONFIG_SYS_CSPR0_EXT + set_ifc_cspr_ext(IFC_CS0, CONFIG_SYS_CSPR0_EXT); +#endif +#ifdef CONFIG_SYS_CSOR0_EXT + set_ifc_csor_ext(IFC_CS0, CONFIG_SYS_CSOR0_EXT); +#endif + set_ifc_cspr(IFC_CS0, CONFIG_SYS_CSPR0); + set_ifc_amask(IFC_CS0, CONFIG_SYS_AMASK0); + set_ifc_csor(IFC_CS0, CONFIG_SYS_CSOR0); +#endif +#endif + +#ifdef CONFIG_SYS_CSPR1_EXT + set_ifc_cspr_ext(IFC_CS1, CONFIG_SYS_CSPR1_EXT); +#endif +#ifdef CONFIG_SYS_CSOR1_EXT + set_ifc_csor_ext(IFC_CS1, CONFIG_SYS_CSOR1_EXT); +#endif +#if defined(CONFIG_SYS_CSPR1) && defined(CONFIG_SYS_CSOR1) + set_ifc_ftim(IFC_CS1, IFC_FTIM0, CONFIG_SYS_CS1_FTIM0); + set_ifc_ftim(IFC_CS1, IFC_FTIM1, CONFIG_SYS_CS1_FTIM1); + set_ifc_ftim(IFC_CS1, IFC_FTIM2, CONFIG_SYS_CS1_FTIM2); + set_ifc_ftim(IFC_CS1, IFC_FTIM3, CONFIG_SYS_CS1_FTIM3); + + set_ifc_csor(IFC_CS1, CONFIG_SYS_CSOR1); + set_ifc_amask(IFC_CS1, CONFIG_SYS_AMASK1); + set_ifc_cspr(IFC_CS1, CONFIG_SYS_CSPR1); +#endif + +#ifdef CONFIG_SYS_CSPR2_EXT + set_ifc_cspr_ext(IFC_CS2, CONFIG_SYS_CSPR2_EXT); +#endif +#ifdef CONFIG_SYS_CSOR2_EXT + set_ifc_csor_ext(IFC_CS2, CONFIG_SYS_CSOR2_EXT); +#endif +#if defined(CONFIG_SYS_CSPR2) && defined(CONFIG_SYS_CSOR2) + set_ifc_ftim(IFC_CS2, IFC_FTIM0, CONFIG_SYS_CS2_FTIM0); + set_ifc_ftim(IFC_CS2, IFC_FTIM1, CONFIG_SYS_CS2_FTIM1); + set_ifc_ftim(IFC_CS2, IFC_FTIM2, CONFIG_SYS_CS2_FTIM2); + set_ifc_ftim(IFC_CS2, IFC_FTIM3, CONFIG_SYS_CS2_FTIM3); + + set_ifc_csor(IFC_CS2, CONFIG_SYS_CSOR2); + set_ifc_amask(IFC_CS2, CONFIG_SYS_AMASK2); + set_ifc_cspr(IFC_CS2, CONFIG_SYS_CSPR2); +#endif + +#ifdef CONFIG_SYS_CSPR3_EXT + set_ifc_cspr_ext(IFC_CS3, CONFIG_SYS_CSPR3_EXT); +#endif +#ifdef CONFIG_SYS_CSOR3_EXT + set_ifc_csor_ext(IFC_CS3, CONFIG_SYS_CSOR3_EXT); +#endif +#if defined(CONFIG_SYS_CSPR3) && defined(CONFIG_SYS_CSOR3) + set_ifc_ftim(IFC_CS3, IFC_FTIM0, CONFIG_SYS_CS3_FTIM0); + set_ifc_ftim(IFC_CS3, IFC_FTIM1, CONFIG_SYS_CS3_FTIM1); + set_ifc_ftim(IFC_CS3, IFC_FTIM2, CONFIG_SYS_CS3_FTIM2); + set_ifc_ftim(IFC_CS3, IFC_FTIM3, CONFIG_SYS_CS3_FTIM3); + + set_ifc_cspr(IFC_CS3, CONFIG_SYS_CSPR3); + set_ifc_amask(IFC_CS3, CONFIG_SYS_AMASK3); + set_ifc_csor(IFC_CS3, CONFIG_SYS_CSOR3); +#endif + +#ifdef CONFIG_SYS_CSPR4_EXT + set_ifc_cspr_ext(IFC_CS4, CONFIG_SYS_CSPR4_EXT); +#endif +#ifdef CONFIG_SYS_CSOR4_EXT + set_ifc_csor_ext(IFC_CS4, CONFIG_SYS_CSOR4_EXT); +#endif +#if defined(CONFIG_SYS_CSPR4) && defined(CONFIG_SYS_CSOR4) + set_ifc_ftim(IFC_CS4, IFC_FTIM0, CONFIG_SYS_CS4_FTIM0); + set_ifc_ftim(IFC_CS4, IFC_FTIM1, CONFIG_SYS_CS4_FTIM1); + set_ifc_ftim(IFC_CS4, IFC_FTIM2, CONFIG_SYS_CS4_FTIM2); + set_ifc_ftim(IFC_CS4, IFC_FTIM3, CONFIG_SYS_CS4_FTIM3); + + set_ifc_cspr(IFC_CS4, CONFIG_SYS_CSPR4); + set_ifc_amask(IFC_CS4, CONFIG_SYS_AMASK4); + set_ifc_csor(IFC_CS4, CONFIG_SYS_CSOR4); +#endif + +#ifdef CONFIG_SYS_CSPR5_EXT + set_ifc_cspr_ext(IFC_CS5, CONFIG_SYS_CSPR5_EXT); +#endif +#ifdef CONFIG_SYS_CSOR5_EXT + set_ifc_csor_ext(IFC_CS5, CONFIG_SYS_CSOR5_EXT); +#endif +#if defined(CONFIG_SYS_CSPR5) && defined(CONFIG_SYS_CSOR5) + set_ifc_ftim(IFC_CS5, IFC_FTIM0, CONFIG_SYS_CS5_FTIM0); + set_ifc_ftim(IFC_CS5, IFC_FTIM1, CONFIG_SYS_CS5_FTIM1); + set_ifc_ftim(IFC_CS5, IFC_FTIM2, CONFIG_SYS_CS5_FTIM2); + set_ifc_ftim(IFC_CS5, IFC_FTIM3, CONFIG_SYS_CS5_FTIM3); + + set_ifc_cspr(IFC_CS5, CONFIG_SYS_CSPR5); + set_ifc_amask(IFC_CS5, CONFIG_SYS_AMASK5); + set_ifc_csor(IFC_CS5, CONFIG_SYS_CSOR5); +#endif + +#ifdef CONFIG_SYS_CSPR6_EXT + set_ifc_cspr_ext(IFC_CS6, CONFIG_SYS_CSPR6_EXT); +#endif +#ifdef CONFIG_SYS_CSOR6_EXT + set_ifc_csor_ext(IFC_CS6, CONFIG_SYS_CSOR6_EXT); +#endif +#if defined(CONFIG_SYS_CSPR6) && defined(CONFIG_SYS_CSOR6) + set_ifc_ftim(IFC_CS6, IFC_FTIM0, CONFIG_SYS_CS6_FTIM0); + set_ifc_ftim(IFC_CS6, IFC_FTIM1, CONFIG_SYS_CS6_FTIM1); + set_ifc_ftim(IFC_CS6, IFC_FTIM2, CONFIG_SYS_CS6_FTIM2); + set_ifc_ftim(IFC_CS6, IFC_FTIM3, CONFIG_SYS_CS6_FTIM3); + + set_ifc_cspr(IFC_CS6, CONFIG_SYS_CSPR6); + set_ifc_amask(IFC_CS6, CONFIG_SYS_AMASK6); + set_ifc_csor(IFC_CS6, CONFIG_SYS_CSOR6); +#endif + +#ifdef CONFIG_SYS_CSPR7_EXT + set_ifc_cspr_ext(IFC_CS7, CONFIG_SYS_CSPR7_EXT); +#endif +#ifdef CONFIG_SYS_CSOR7_EXT + set_ifc_csor_ext(IFC_CS7, CONFIG_SYS_CSOR7_EXT); +#endif +#if defined(CONFIG_SYS_CSPR7) && defined(CONFIG_SYS_CSOR7) + set_ifc_ftim(IFC_CS7, IFC_FTIM0, CONFIG_SYS_CS7_FTIM0); + set_ifc_ftim(IFC_CS7, IFC_FTIM1, CONFIG_SYS_CS7_FTIM1); + set_ifc_ftim(IFC_CS7, IFC_FTIM2, CONFIG_SYS_CS7_FTIM2); + set_ifc_ftim(IFC_CS7, IFC_FTIM3, CONFIG_SYS_CS7_FTIM3); + + set_ifc_cspr(IFC_CS7, CONFIG_SYS_CSPR7); + set_ifc_amask(IFC_CS7, CONFIG_SYS_AMASK7); + set_ifc_csor(IFC_CS7, CONFIG_SYS_CSOR7); +#endif +} diff --git a/drivers/misc/gpio_led.c b/drivers/misc/gpio_led.c index 3fedddc8b..3e95727d7 100644 --- a/drivers/misc/gpio_led.c +++ b/drivers/misc/gpio_led.c @@ -9,15 +9,42 @@ #include <status_led.h> #include <asm/gpio.h> +#ifndef CONFIG_GPIO_LED_INVERTED_TABLE +#define CONFIG_GPIO_LED_INVERTED_TABLE {} +#endif + +static led_id_t gpio_led_inv[] = CONFIG_GPIO_LED_INVERTED_TABLE; + +static int gpio_led_gpio_value(led_id_t mask, int state) +{ + int i, gpio_value = (state == STATUS_LED_ON); + + for (i = 0; i < ARRAY_SIZE(gpio_led_inv); i++) { + if (gpio_led_inv[i] == mask) + gpio_value = !gpio_value; + } + + return gpio_value; +} + void __led_init(led_id_t mask, int state) { - gpio_request(mask, "gpio_led"); - gpio_direction_output(mask, state == STATUS_LED_ON); + int gpio_value; + + if (gpio_request(mask, "gpio_led") != 0) { + printf("%s: failed requesting GPIO%lu!\n", __func__, mask); + return; + } + + gpio_value = gpio_led_gpio_value(mask, state); + gpio_direction_output(mask, gpio_value); } void __led_set(led_id_t mask, int state) { - gpio_set_value(mask, state == STATUS_LED_ON); + int gpio_value = gpio_led_gpio_value(mask, state); + + gpio_set_value(mask, gpio_value); } void __led_toggle(led_id_t mask) diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index a7ae38dad..1ed26cab3 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_BFIN_SDH) += bfin_sdh.o obj-$(CONFIG_DAVINCI_MMC) += davinci_mmc.o obj-$(CONFIG_FSL_ESDHC) += fsl_esdhc.o obj-$(CONFIG_FTSDC010) += ftsdc010_mci.o +obj-$(CONFIG_FTSDC021) += ftsdc021_sdhci.o obj-$(CONFIG_GENERIC_MMC) += mmc.o obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c index 1e0f72bbe..19d9b0b89 100644 --- a/drivers/mmc/dw_mmc.c +++ b/drivers/mmc/dw_mmc.c @@ -11,7 +11,6 @@ #include <mmc.h> #include <dwmmc.h> #include <asm-generic/errno.h> -#include <asm/arch/dwmmc.h> #define PAGE_SIZE 4096 @@ -300,17 +299,9 @@ static void dwmci_set_ios(struct mmc *mmc) static int dwmci_init(struct mmc *mmc) { struct dwmci_host *host = (struct dwmci_host *)mmc->priv; - u32 fifo_size; - if (host->quirks & DWMCI_QUIRK_DISABLE_SMU) { - dwmci_writel(host, EMMCP_MPSBEGIN0, 0); - dwmci_writel(host, EMMCP_SEND0, 0); - dwmci_writel(host, EMMCP_CTRL0, - MPSCTRL_SECURE_READ_BIT | - MPSCTRL_SECURE_WRITE_BIT | - MPSCTRL_NON_SECURE_READ_BIT | - MPSCTRL_NON_SECURE_WRITE_BIT | MPSCTRL_VALID); - } + if (host->board_init) + host->board_init(host); dwmci_writel(host, DWMCI_PWREN, 1); @@ -330,13 +321,9 @@ static int dwmci_init(struct mmc *mmc) dwmci_writel(host, DWMCI_IDINTEN, 0); dwmci_writel(host, DWMCI_BMOD, 1); - if (!host->fifoth_val) { - fifo_size = dwmci_readl(host, DWMCI_FIFOTH); - fifo_size = ((fifo_size & RX_WMARK_MASK) >> RX_WMARK_SHIFT) + 1; - host->fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size / 2 - 1) | - TX_WMARK(fifo_size / 2); + if (host->fifoth_val) { + dwmci_writel(host, DWMCI_FIFOTH, host->fifoth_val); } - dwmci_writel(host, DWMCI_FIFOTH, host->fifoth_val); dwmci_writel(host, DWMCI_CLKENA, 0); dwmci_writel(host, DWMCI_CLKSRC, 0); diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c index a0f1511cb..b3e5c5e5e 100644 --- a/drivers/mmc/exynos_dw_mmc.c +++ b/drivers/mmc/exynos_dw_mmc.c @@ -34,6 +34,19 @@ unsigned int exynos_dwmci_get_clk(int dev_index) return get_mmc_clk(dev_index); } +static void exynos_dwmci_board_init(struct dwmci_host *host) +{ + if (host->quirks & DWMCI_QUIRK_DISABLE_SMU) { + dwmci_writel(host, EMMCP_MPSBEGIN0, 0); + dwmci_writel(host, EMMCP_SEND0, 0); + dwmci_writel(host, EMMCP_CTRL0, + MPSCTRL_SECURE_READ_BIT | + MPSCTRL_SECURE_WRITE_BIT | + MPSCTRL_NON_SECURE_READ_BIT | + MPSCTRL_NON_SECURE_WRITE_BIT | MPSCTRL_VALID); + } +} + /* * This function adds the mmc channel to be registered with mmc core. * index - mmc channel number. @@ -65,6 +78,7 @@ int exynos_dwmci_add_port(int index, u32 regbase, int bus_width, u32 clksel) #ifdef CONFIG_EXYNOS5420 host->quirks = DWMCI_QUIRK_DISABLE_SMU; #endif + host->board_init = exynos_dwmci_board_init; if (clksel) { host->clksel_val = clksel; diff --git a/drivers/mmc/fsl_esdhc_spl.c b/drivers/mmc/fsl_esdhc_spl.c index 65c52a22d..8fc263f4f 100644 --- a/drivers/mmc/fsl_esdhc_spl.c +++ b/drivers/mmc/fsl_esdhc_spl.c @@ -42,6 +42,10 @@ void __noreturn mmc_boot(void) hang(); } +#ifdef CONFIG_FSL_CORENET + offset = CONFIG_SYS_MMC_U_BOOT_OFFS; + code_len = CONFIG_SYS_MMC_U_BOOT_SIZE; +#else blklen = mmc->read_bl_len; tmp_buf = malloc(blklen); if (!tmp_buf) { @@ -91,6 +95,7 @@ void __noreturn mmc_boot(void) /* * Load U-Boot image from mmc into RAM */ +#endif blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len; blk_cnt = ALIGN(code_len, mmc->read_bl_len) / mmc->read_bl_len; err = mmc->block_dev.block_read(0, blk_start, blk_cnt, diff --git a/drivers/mmc/ftsdc021_sdhci.c b/drivers/mmc/ftsdc021_sdhci.c new file mode 100644 index 000000000..1f6cdba17 --- /dev/null +++ b/drivers/mmc/ftsdc021_sdhci.c @@ -0,0 +1,33 @@ +/* + * (C) Copyright 2013 Faraday Technology + * Kuo-Jung Su <dantesu@faraday-tech.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <malloc.h> +#include <sdhci.h> + +#ifndef CONFIG_FTSDC021_CLOCK +#define CONFIG_FTSDC021_CLOCK clk_get_rate("MMC") +#endif + +int ftsdc021_sdhci_init(u32 regbase) +{ + struct sdhci_host *host = NULL; + uint32_t freq = CONFIG_FTSDC021_CLOCK; + + host = calloc(1, sizeof(struct sdhci_host)); + if (!host) { + puts("sdh_host malloc fail!\n"); + return 1; + } + + host->name = "FTSDC021"; + host->ioaddr = (void __iomem *)regbase; + host->quirks = 0; + add_sdhci(host, freq, 0); + + return 0; +} diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index eb1eafaf0..e145cd184 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -58,6 +58,7 @@ obj-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o obj-$(CONFIG_NAND_SPEAR) += spr_nand.o obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o obj-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o +obj-$(CONFIG_NAND_OMAP_ELM) += omap_elm.o obj-$(CONFIG_NAND_PLAT) += nand_plat.o obj-$(CONFIG_NAND_DOCG4) += docg4.o diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index da83f06e4..05ddfbb64 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -12,9 +12,8 @@ */ #include <common.h> -#include <asm/arch/hardware.h> +#include <asm/gpio.h> #include <asm/arch/gpio.h> -#include <asm/arch/at91_pio.h> #include <malloc.h> #include <nand.h> @@ -412,7 +411,7 @@ static int pmecc_err_location(struct mtd_info *mtd) } if (!timeout) { - printk(KERN_ERR "atmel_nand : Timeout to calculate PMECC error location\n"); + dev_err(host->dev, "atmel_nand : Timeout to calculate PMECC error location\n"); return -1; } @@ -452,7 +451,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, *(buf + byte_pos) ^= (1 << bit_pos); pos = sector_num * host->pmecc_sector_size + byte_pos; - printk(KERN_INFO "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + dev_dbg(host->dev, "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", pos, bit_pos, err_byte, *(buf + byte_pos)); } else { /* Bit flip in OOB area */ @@ -462,7 +461,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, ecc[tmp] ^= (1 << bit_pos); pos = tmp + nand_chip->ecc.layout->eccpos[0]; - printk(KERN_INFO "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + dev_dbg(host->dev, "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", pos, bit_pos, err_byte, ecc[tmp]); } @@ -500,7 +499,7 @@ normal_check: err_nbr = pmecc_err_location(mtd); if (err_nbr == -1) { - printk(KERN_ERR "PMECC: Too many errors\n"); + dev_err(host->dev, "PMECC: Too many errors\n"); mtd->ecc_stats.failed++; return -EIO; } else { @@ -544,7 +543,7 @@ static int atmel_nand_pmecc_read_page(struct mtd_info *mtd, } if (!timeout) { - printk(KERN_ERR "atmel_nand : Timeout to read PMECC page\n"); + dev_err(host->dev, "atmel_nand : Timeout to read PMECC page\n"); return -1; } @@ -584,7 +583,7 @@ static int atmel_nand_pmecc_write_page(struct mtd_info *mtd, } if (!timeout) { - printk(KERN_ERR "atmel_nand : Timeout to read PMECC status, fail to write PMECC in oob\n"); + dev_err(host->dev, "atmel_nand : Timeout to read PMECC status, fail to write PMECC in oob\n"); goto out; } @@ -827,6 +826,7 @@ static int atmel_pmecc_nand_init_params(struct nand_chip *nand, switch (mtd->writesize) { case 2048: case 4096: + case 8192: host->pmecc_degree = (sector_size == 512) ? PMECC_GF_DIMENSION_13 : PMECC_GF_DIMENSION_14; host->pmecc_cw_len = (1 << host->pmecc_degree) - 1; @@ -840,8 +840,15 @@ static int atmel_pmecc_nand_init_params(struct nand_chip *nand, nand->ecc.steps = 1; nand->ecc.bytes = host->pmecc_bytes_per_sector * host->pmecc_sector_number; + + if (nand->ecc.bytes > MTD_MAX_ECCPOS_ENTRIES_LARGE) { + dev_err(host->dev, "too large eccpos entries. max support ecc.bytes is %d\n", + MTD_MAX_ECCPOS_ENTRIES_LARGE); + return -EINVAL; + } + if (nand->ecc.bytes > mtd->oobsize - 2) { - printk(KERN_ERR "No room for ECC bytes\n"); + dev_err(host->dev, "No room for ECC bytes\n"); return -EINVAL; } pmecc_config_ecc_layout(&atmel_pmecc_oobinfo, @@ -852,7 +859,7 @@ static int atmel_pmecc_nand_init_params(struct nand_chip *nand, case 512: case 1024: /* TODO */ - printk(KERN_ERR "Unsupported page size for PMECC, use Software ECC\n"); + dev_err(host->dev, "Unsupported page size for PMECC, use Software ECC\n"); default: /* page size not handled by HW ECC */ /* switching back to soft ECC */ @@ -1035,7 +1042,7 @@ static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat, /* it doesn't seems to be a freshly * erased block. * We can't correct so many errors */ - printk(KERN_WARNING "atmel_nand : multiple errors detected." + dev_warn(host->dev, "atmel_nand : multiple errors detected." " Unable to correct.\n"); return -EIO; } @@ -1045,12 +1052,12 @@ static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat, /* there's nothing much to do here. * the bit error is on the ECC itself. */ - printk(KERN_WARNING "atmel_nand : one bit error on ECC code." + dev_warn(host->dev, "atmel_nand : one bit error on ECC code." " Nothing to correct\n"); return 0; } - printk(KERN_WARNING "atmel_nand : one bit error on data." + dev_warn(host->dev, "atmel_nand : one bit error on data." " (word offset in the page :" " 0x%x bit offset : 0x%x)\n", ecc_word, ecc_bit); @@ -1062,7 +1069,7 @@ static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat, /* 8 bits words */ dat[ecc_word] ^= (1 << ecc_bit); } - printk(KERN_WARNING "atmel_nand : error corrected\n"); + dev_warn(host->dev, "atmel_nand : error corrected\n"); return 1; } @@ -1146,8 +1153,7 @@ static void at91_nand_hwcontrol(struct mtd_info *mtd, IO_ADDR_W |= CONFIG_SYS_NAND_MASK_ALE; #ifdef CONFIG_SYS_NAND_ENABLE_PIN - at91_set_gpio_value(CONFIG_SYS_NAND_ENABLE_PIN, - !(ctrl & NAND_NCE)); + gpio_set_value(CONFIG_SYS_NAND_ENABLE_PIN, !(ctrl & NAND_NCE)); #endif this->IO_ADDR_W = (void *) IO_ADDR_W; } @@ -1159,7 +1165,7 @@ static void at91_nand_hwcontrol(struct mtd_info *mtd, #ifdef CONFIG_SYS_NAND_READY_PIN static int at91_nand_ready(struct mtd_info *mtd) { - return at91_get_gpio_value(CONFIG_SYS_NAND_READY_PIN); + return gpio_get_value(CONFIG_SYS_NAND_READY_PIN); } #endif @@ -1178,7 +1184,11 @@ int atmel_nand_chip_init(int devnum, ulong base_addr) mtd->priv = nand; nand->IO_ADDR_R = nand->IO_ADDR_W = (void __iomem *)base_addr; +#ifdef CONFIG_NAND_ECC_BCH + nand->ecc.mode = NAND_ECC_SOFT_BCH; +#else nand->ecc.mode = NAND_ECC_SOFT; +#endif #ifdef CONFIG_SYS_NAND_DBW_16 nand->options = NAND_BUSWIDTH_16; #endif @@ -1186,7 +1196,7 @@ int atmel_nand_chip_init(int devnum, ulong base_addr) #ifdef CONFIG_SYS_NAND_READY_PIN nand->dev_ready = at91_nand_ready; #endif - nand->chip_delay = 20; + nand->chip_delay = 75; ret = nand_scan_ident(mtd, CONFIG_SYS_NAND_MAX_CHIPS, NULL); if (ret) @@ -1214,6 +1224,6 @@ void board_nand_init(void) int i; for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) if (atmel_nand_chip_init(i, base_addr[i])) - printk(KERN_ERR "atmel_nand: Fail to initialize #%d chip", + dev_err(host->dev, "atmel_nand: Fail to initialize #%d chip", i); } diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index 98a09c064..1808a7ffb 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -17,7 +17,7 @@ #include <asm/io.h> #include <asm/errno.h> -#include <asm/fsl_ifc.h> +#include <fsl_ifc.h> #define FSL_IFC_V1_1_0 0x01010000 #define MAX_BANKS 4 @@ -125,6 +125,69 @@ static struct nand_ecclayout oob_4096_ecc8 = { .oobfree = { {2, 6}, {136, 82} }, }; +/* 8192-byte page size with 4-bit ECC */ +static struct nand_ecclayout oob_8192_ecc4 = { + .eccbytes = 128, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + }, + .oobfree = { {2, 6}, {136, 208} }, +}; + +/* 8192-byte page size with 8-bit ECC -- requires 218-byte OOB */ +static struct nand_ecclayout oob_8192_ecc8 = { + .eccbytes = 256, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + 136, 137, 138, 139, 140, 141, 142, 143, + 144, 145, 146, 147, 148, 149, 150, 151, + 152, 153, 154, 155, 156, 157, 158, 159, + 160, 161, 162, 163, 164, 165, 166, 167, + 168, 169, 170, 171, 172, 173, 174, 175, + 176, 177, 178, 179, 180, 181, 182, 183, + 184, 185, 186, 187, 188, 189, 190, 191, + 192, 193, 194, 195, 196, 197, 198, 199, + 200, 201, 202, 203, 204, 205, 206, 207, + 208, 209, 210, 211, 212, 213, 214, 215, + 216, 217, 218, 219, 220, 221, 222, 223, + 224, 225, 226, 227, 228, 229, 230, 231, + 232, 233, 234, 235, 236, 237, 238, 239, + 240, 241, 242, 243, 244, 245, 246, 247, + 248, 249, 250, 251, 252, 253, 254, 255, + 256, 257, 258, 259, 260, 261, 262, 263, + }, + .oobfree = { {2, 6}, {264, 80} }, +}; /* * Generic flash bbt descriptors @@ -428,20 +491,27 @@ static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command, if (mtd->writesize > 512) { nand_fcr0 = (NAND_CMD_SEQIN << IFC_NAND_FCR0_CMD0_SHIFT) | - (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD1_SHIFT); + (NAND_CMD_STATUS << IFC_NAND_FCR0_CMD1_SHIFT) | + (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD2_SHIFT); out_be32(&ifc->ifc_nand.nand_fir0, (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP3_SHIFT) | - (IFC_FIR_OP_CW1 << IFC_NAND_FIR0_OP4_SHIFT)); - out_be32(&ifc->ifc_nand.nand_fir1, 0); + (IFC_FIR_OP_CMD2 << IFC_NAND_FIR0_OP4_SHIFT)); + out_be32(&ifc->ifc_nand.nand_fir1, + (IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP7_SHIFT)); } else { nand_fcr0 = ((NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD1_SHIFT) | (NAND_CMD_SEQIN << - IFC_NAND_FCR0_CMD2_SHIFT)); + IFC_NAND_FCR0_CMD2_SHIFT) | + (NAND_CMD_STATUS << + IFC_NAND_FCR0_CMD3_SHIFT)); out_be32(&ifc->ifc_nand.nand_fir0, (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | @@ -450,7 +520,11 @@ static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command, (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP3_SHIFT) | (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP4_SHIFT)); out_be32(&ifc->ifc_nand.nand_fir1, - (IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT)); + (IFC_FIR_OP_CMD1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_CW3 << IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP7_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP8_SHIFT)); if (column >= mtd->writesize) nand_fcr0 |= @@ -902,6 +976,21 @@ static int fsl_ifc_chip_init(int devnum, u8 *addr) priv->bufnum_mask = 1; break; + case CSOR_NAND_PGS_8K: + if ((csor & CSOR_NAND_ECC_MODE_MASK) == + CSOR_NAND_ECC_MODE_4) { + layout = &oob_8192_ecc4; + nand->ecc.strength = 4; + } else { + layout = &oob_8192_ecc8; + nand->ecc.strength = 8; + nand->ecc.bytes = 16; + } + + priv->bufnum_mask = 0; + break; + + default: printf("ifc nand: bad csor %#x: bad page size\n", csor); return -ENODEV; diff --git a/drivers/mtd/nand/fsl_ifc_spl.c b/drivers/mtd/nand/fsl_ifc_spl.c index d4622653f..9de327ba4 100644 --- a/drivers/mtd/nand/fsl_ifc_spl.c +++ b/drivers/mtd/nand/fsl_ifc_spl.c @@ -9,7 +9,7 @@ #include <common.h> #include <asm/io.h> -#include <asm/fsl_ifc.h> +#include <fsl_ifc.h> #include <linux/mtd/nand.h> static inline int is_blank(uchar *addr, int page_size) @@ -112,10 +112,13 @@ static void nand_load(unsigned int offs, int uboot_size, uchar *dst) port_size = (cspr & CSPR_PORT_SIZE_16) ? 16 : 8; - if (csor & CSOR_NAND_PGS_4K) { + if ((csor & CSOR_NAND_PGS_MASK) == CSOR_NAND_PGS_8K) { + page_size = 8192; + bufnum_mask = 0x0; + } else if ((csor & CSOR_NAND_PGS_MASK) == CSOR_NAND_PGS_4K) { page_size = 4096; bufnum_mask = 0x1; - } else if (csor & CSOR_NAND_PGS_2K) { + } else if ((csor & CSOR_NAND_PGS_MASK) == CSOR_NAND_PGS_2K) { page_size = 2048; bufnum_mask = 0x3; } else { diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/omap_elm.c new file mode 100644 index 000000000..2aa7807f3 --- /dev/null +++ b/drivers/mtd/nand/omap_elm.c @@ -0,0 +1,196 @@ +/* + * (C) Copyright 2010-2011 Texas Instruments, <www.ti.com> + * Mansoor Ahamed <mansoor.ahamed@ti.com> + * + * BCH Error Location Module (ELM) support. + * + * NOTE: + * 1. Supports only continuous mode. Dont see need for page mode in uboot + * 2. Supports only syndrome polynomial 0. i.e. poly local variable is + * always set to ELM_DEFAULT_POLY. Dont see need for other polynomial + * sets in uboot + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/errno.h> +#include <asm/arch/cpu.h> +#include <asm/omap_gpmc.h> +#include <asm/omap_elm.h> + +#define ELM_DEFAULT_POLY (0) + +struct elm *elm_cfg; + +/** + * elm_load_syndromes - Load BCH syndromes based on nibble selection + * @syndrome: BCH syndrome + * @nibbles: + * @poly: Syndrome Polynomial set to use + * + * Load BCH syndromes based on nibble selection + */ +static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly) +{ + u32 *ptr; + u32 val; + + /* reg 0 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[0]; + val = syndrome[0] | (syndrome[1] << 8) | (syndrome[2] << 16) | + (syndrome[3] << 24); + writel(val, ptr); + /* reg 1 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[1]; + val = syndrome[4] | (syndrome[5] << 8) | (syndrome[6] << 16) | + (syndrome[7] << 24); + writel(val, ptr); + + /* BCH 8-bit with 26 nibbles (4*8=32) */ + if (nibbles > 13) { + /* reg 2 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[2]; + val = syndrome[8] | (syndrome[9] << 8) | (syndrome[10] << 16) | + (syndrome[11] << 24); + writel(val, ptr); + /* reg 3 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[3]; + val = syndrome[12] | (syndrome[13] << 8) | + (syndrome[14] << 16) | (syndrome[15] << 24); + writel(val, ptr); + } + + /* BCH 16-bit with 52 nibbles (7*8=56) */ + if (nibbles > 26) { + /* reg 4 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[4]; + val = syndrome[16] | (syndrome[17] << 8) | + (syndrome[18] << 16) | (syndrome[19] << 24); + writel(val, ptr); + + /* reg 5 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[5]; + val = syndrome[20] | (syndrome[21] << 8) | + (syndrome[22] << 16) | (syndrome[23] << 24); + writel(val, ptr); + + /* reg 6 */ + ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6]; + val = syndrome[24] | (syndrome[25] << 8) | + (syndrome[26] << 16) | (syndrome[27] << 24); + writel(val, ptr); + } +} + +/** + * elm_check_errors - Check for BCH errors and return error locations + * @syndrome: BCH syndrome + * @nibbles: + * @error_count: Returns number of errrors in the syndrome + * @error_locations: Returns error locations (in decimal) in this array + * + * Check the provided syndrome for BCH errors and return error count + * and locations in the array passed. Returns -1 if error is not correctable, + * else returns 0 + */ +int elm_check_error(u8 *syndrome, u32 nibbles, u32 *error_count, + u32 *error_locations) +{ + u8 poly = ELM_DEFAULT_POLY; + s8 i; + u32 location_status; + + elm_load_syndromes(syndrome, nibbles, poly); + + /* start processing */ + writel((readl(&elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6]) + | ELM_SYNDROME_FRAGMENT_6_SYNDROME_VALID), + &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6]); + + /* wait for processing to complete */ + while ((readl(&elm_cfg->irqstatus) & (0x1 << poly)) != 0x1) + ; + /* clear status */ + writel((readl(&elm_cfg->irqstatus) | (0x1 << poly)), + &elm_cfg->irqstatus); + + /* check if correctable */ + location_status = readl(&elm_cfg->error_location[poly].location_status); + if (!(location_status & ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK)) + return -1; + + /* get error count */ + *error_count = readl(&elm_cfg->error_location[poly].location_status) & + ELM_LOCATION_STATUS_ECC_NB_ERRORS_MASK; + + for (i = 0; i < *error_count; i++) { + error_locations[i] = + readl(&elm_cfg->error_location[poly].error_location_x[i]); + } + + return 0; +} + + +/** + * elm_config - Configure ELM module + * @level: 4 / 8 / 16 bit BCH + * + * Configure ELM module based on BCH level. + * Set mode as continuous mode. + * Currently we are using only syndrome 0 and syndromes 1 to 6 are not used. + * Also, the mode is set only for syndrome 0 + */ +int elm_config(enum bch_level level) +{ + u32 val; + u8 poly = ELM_DEFAULT_POLY; + u32 buffer_size = 0x7FF; + + /* config size and level */ + val = (u32)(level) & ELM_LOCATION_CONFIG_ECC_BCH_LEVEL_MASK; + val |= ((buffer_size << ELM_LOCATION_CONFIG_ECC_SIZE_POS) & + ELM_LOCATION_CONFIG_ECC_SIZE_MASK); + writel(val, &elm_cfg->location_config); + + /* config continous mode */ + /* enable interrupt generation for syndrome polynomial set */ + writel((readl(&elm_cfg->irqenable) | (0x1 << poly)), + &elm_cfg->irqenable); + /* set continuous mode for the syndrome polynomial set */ + writel((readl(&elm_cfg->page_ctrl) & ~(0x1 << poly)), + &elm_cfg->page_ctrl); + + return 0; +} + +/** + * elm_reset - Do a soft reset of ELM + * + * Perform a soft reset of ELM and return after reset is done. + */ +void elm_reset(void) +{ + /* initiate reset */ + writel((readl(&elm_cfg->sysconfig) | ELM_SYSCONFIG_SOFTRESET), + &elm_cfg->sysconfig); + + /* wait for reset complete and normal operation */ + while ((readl(&elm_cfg->sysstatus) & ELM_SYSSTATUS_RESETDONE) != + ELM_SYSSTATUS_RESETDONE) + ; +} + +/** + * elm_init - Initialize ELM module + * + * Initialize ELM support. Currently it does only base address init + * and ELM reset. + */ +void elm_init(void) +{ + elm_cfg = (struct elm *)ELM_BASE; + elm_reset(); +} diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c index ec1787f22..5e7e6b337 100644 --- a/drivers/mtd/nand/omap_gpmc.c +++ b/drivers/mtd/nand/omap_gpmc.c @@ -15,15 +15,13 @@ #include <linux/bch.h> #include <linux/compiler.h> #include <nand.h> -#ifdef CONFIG_AM33XX -#include <asm/arch/elm.h> -#endif +#include <asm/omap_elm.h> + +#define BADBLOCK_MARKER_LENGTH 2 +#define SECTOR_BYTES 512 static uint8_t cs; -static __maybe_unused struct nand_ecclayout hw_nand_oob = - GPMC_NAND_HW_ECC_LAYOUT; -static __maybe_unused struct nand_ecclayout hw_bch8_nand_oob = - GPMC_NAND_HW_BCH8_ECC_LAYOUT; +static __maybe_unused struct nand_ecclayout omap_ecclayout; /* * omap_nand_hwcontrol - Set the address pointers corretly for the @@ -233,6 +231,7 @@ struct nand_bch_priv { uint8_t type; uint8_t nibbles; struct bch_control *control; + enum omap_ecc ecc_scheme; }; /* bch types */ @@ -274,17 +273,15 @@ static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) { uint32_t val; uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; -#ifdef CONFIG_AM33XX uint32_t unused_length = 0; -#endif uint32_t wr_mode = BCH_WRAPMODE_6; struct nand_bch_priv *bch = chip->priv; /* Clear the ecc result registers, select ecc reg as 1 */ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); -#ifdef CONFIG_AM33XX - wr_mode = BCH_WRAPMODE_1; + if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) { + wr_mode = BCH_WRAPMODE_1; switch (bch->nibbles) { case ECC_BCH4_NIBBLES: @@ -320,7 +317,7 @@ static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) val |= (unused_length << 22); break; } -#else + } else { /* * This ecc_size_config setting is for BCH sw library. * @@ -333,7 +330,7 @@ static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) * size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) */ val = (32 << 22) | (0 << 12); -#endif + } /* ecc size configuration */ writel(val, &gpmc_cfg->ecc_size_config); @@ -376,9 +373,9 @@ static void __maybe_unused omap_ecc_disable(struct mtd_info *mtd) } /* - * BCH8 support (needs ELM and thus AM33xx-only) + * BCH support using ELM module */ -#ifdef CONFIG_AM33XX +#ifdef CONFIG_NAND_OMAP_ELM /* * omap_read_bch8_result - Read BCH result for BCH8 level * @@ -631,20 +628,20 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, } return 0; } -#endif /* CONFIG_AM33XX */ +#endif /* CONFIG_NAND_OMAP_ELM */ /* * OMAP3 BCH8 support (with BCH library) */ -#ifdef CONFIG_NAND_OMAP_BCH8 +#ifdef CONFIG_BCH /* - * omap_calculate_ecc_bch - Read BCH ECC result + * omap_calculate_ecc_bch_sw - Read BCH ECC result * * @mtd: MTD device structure * @dat: The pointer to data on which ecc is computed (unused here) * @ecc: The ECC output buffer */ -static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, +static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc) { int ret = 0; @@ -689,13 +686,13 @@ static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, } /** - * omap_correct_data_bch - Decode received data and correct errors + * omap_correct_data_bch_sw - Decode received data and correct errors * @mtd: MTD device structure * @data: page data * @read_ecc: ecc read from nand flash * @calc_ecc: ecc read from HW ECC registers */ -static int omap_correct_data_bch(struct mtd_info *mtd, u_char *data, +static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data, u_char *read_ecc, u_char *calc_ecc) { int i, count; @@ -752,7 +749,150 @@ static void __maybe_unused omap_free_bch(struct mtd_info *mtd) chip_priv->control = NULL; } } -#endif /* CONFIG_NAND_OMAP_BCH8 */ +#endif /* CONFIG_BCH */ + +/** + * omap_select_ecc_scheme - configures driver for particular ecc-scheme + * @nand: NAND chip device structure + * @ecc_scheme: ecc scheme to configure + * @pagesize: number of main-area bytes per page of NAND device + * @oobsize: number of OOB/spare bytes per page of NAND device + */ +static int omap_select_ecc_scheme(struct nand_chip *nand, + enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) { + struct nand_bch_priv *bch = nand->priv; + struct nand_ecclayout *ecclayout = nand->ecc.layout; + int eccsteps = pagesize / SECTOR_BYTES; + int i; + + switch (ecc_scheme) { + case OMAP_ECC_HAM1_CODE_SW: + debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n"); + /* For this ecc-scheme, ecc.bytes, ecc.layout, ... are + * initialized in nand_scan_tail(), so just set ecc.mode */ + bch_priv.control = NULL; + bch_priv.type = 0; + nand->ecc.mode = NAND_ECC_SOFT; + nand->ecc.layout = NULL; + nand->ecc.size = pagesize; + bch->ecc_scheme = OMAP_ECC_HAM1_CODE_SW; + break; + + case OMAP_ECC_HAM1_CODE_HW: + debug("nand: selected OMAP_ECC_HAM1_CODE_HW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((3 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (3 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + bch_priv.control = NULL; + bch_priv.type = 0; + /* populate ecc specific fields */ + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 1; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 3; + nand->ecc.hwctl = omap_enable_hwecc; + nand->ecc.correct = omap_correct_data; + nand->ecc.calculate = omap_calculate_ecc; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + for (i = 0; i < ecclayout->eccbytes; i++) + ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + bch->ecc_scheme = OMAP_ECC_HAM1_CODE_HW; + break; + + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: +#ifdef CONFIG_BCH + debug("nand: selected OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((13 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (13 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + /* check if BCH S/W library can be used for error detection */ + bch_priv.control = init_bch(13, 8, 0x201b); + if (!bch_priv.control) { + printf("nand: error: could not init_bch()\n"); + return -ENODEV; + } + bch_priv.type = ECC_BCH8; + /* populate ecc specific fields */ + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 8; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 13; + nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.correct = omap_correct_data_bch_sw; + nand->ecc.calculate = omap_calculate_ecc_bch_sw; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + for (i = 1; i < ecclayout->eccbytes; i++) { + if (i % nand->ecc.bytes) + ecclayout->eccpos[i] = + ecclayout->eccpos[i - 1] + 1; + else + ecclayout->eccpos[i] = + ecclayout->eccpos[i - 1] + 2; + } + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + omap_hwecc_init_bch(nand, NAND_ECC_READ); + bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW; + break; +#else + printf("nand: error: CONFIG_BCH required for ECC\n"); + return -EINVAL; +#endif + + case OMAP_ECC_BCH8_CODE_HW: +#ifdef CONFIG_NAND_OMAP_ELM + debug("nand: selected OMAP_ECC_BCH8_CODE_HW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((14 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (14 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + /* intialize ELM for ECC error detection */ + elm_init(); + bch_priv.type = ECC_BCH8; + /* populate ecc specific fields */ + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 8; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 14; + nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.correct = omap_correct_data_bch; + nand->ecc.calculate = omap_calculate_ecc_bch; + nand->ecc.read_page = omap_read_page_bch; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + for (i = 0; i < ecclayout->eccbytes; i++) + ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW; + break; +#else + printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n"); + return -EINVAL; +#endif + + default: + debug("nand: error: ecc scheme not enabled or supported\n"); + return -EINVAL; + } + return 0; +} #ifndef CONFIG_SPL_BUILD /* @@ -763,77 +903,45 @@ static void __maybe_unused omap_free_bch(struct mtd_info *mtd) * @eccstrength - the number of bits that could be corrected * (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16) */ -void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength) +int __maybe_unused omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength) { struct nand_chip *nand; struct mtd_info *mtd; + int err = 0; if (nand_curr_device < 0 || nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE || !nand_info[nand_curr_device].name) { - printf("Error: Can't switch ecc, no devices available\n"); - return; + printf("nand: error: no NAND devices found\n"); + return -ENODEV; } mtd = &nand_info[nand_curr_device]; nand = mtd->priv; - nand->options |= NAND_OWN_BUFFERS; - - /* Reset ecc interface */ - nand->ecc.mode = NAND_ECC_NONE; - nand->ecc.read_page = NULL; - nand->ecc.write_page = NULL; - nand->ecc.read_oob = NULL; - nand->ecc.write_oob = NULL; - nand->ecc.hwctl = NULL; - nand->ecc.correct = NULL; - nand->ecc.calculate = NULL; - nand->ecc.strength = eccstrength; - /* Setup the ecc configurations again */ if (hardware) { if (eccstrength == 1) { - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_nand_oob; - nand->ecc.size = 512; - nand->ecc.bytes = 3; - nand->ecc.hwctl = omap_enable_hwecc; - nand->ecc.correct = omap_correct_data; - nand->ecc.calculate = omap_calculate_ecc; - omap_hwecc_init(nand); - printf("1-bit hamming HW ECC selected\n"); - } -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) - else if (eccstrength == 8) { - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_bch8_nand_oob; - nand->ecc.size = 512; -#ifdef CONFIG_AM33XX - nand->ecc.bytes = 14; - nand->ecc.read_page = omap_read_page_bch; -#else - nand->ecc.bytes = 13; -#endif - nand->ecc.hwctl = omap_enable_ecc_bch; - nand->ecc.correct = omap_correct_data_bch; - nand->ecc.calculate = omap_calculate_ecc_bch; - omap_hwecc_init_bch(nand, NAND_ECC_READ); - printf("8-bit BCH HW ECC selected\n"); + err = omap_select_ecc_scheme(nand, + OMAP_ECC_HAM1_CODE_HW, + mtd->writesize, mtd->oobsize); + } else if (eccstrength == 8) { + err = omap_select_ecc_scheme(nand, + OMAP_ECC_BCH8_CODE_HW, + mtd->writesize, mtd->oobsize); + } else { + printf("nand: error: unsupported ECC scheme\n"); + return -EINVAL; } -#endif } else { - nand->ecc.mode = NAND_ECC_SOFT; - /* Use mtd default settings */ - nand->ecc.layout = NULL; - nand->ecc.size = 0; - printf("SW ECC selected\n"); + err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW, + mtd->writesize, mtd->oobsize); } /* Update NAND handling after ECC mode switch */ - nand_scan_tail(mtd); - - nand->options &= ~NAND_OWN_BUFFERS; + if (!err) + err = nand_scan_tail(mtd); + return err; } #endif /* CONFIG_SPL_BUILD */ @@ -856,7 +964,7 @@ int board_nand_init(struct nand_chip *nand) { int32_t gpmc_config = 0; cs = 0; - + int err = 0; /* * xloader/Uboot's gpmc configuration would have configured GPMC for * nand type of memory. The following logic scans and latches on to the @@ -873,7 +981,7 @@ int board_nand_init(struct nand_chip *nand) cs++; } if (cs >= GPMC_MAX_CS) { - printf("NAND: Unable to find NAND settings in " + printf("nand: error: Unable to find NAND settings in " "GPMC Configuration - quitting\n"); return -ENODEV; } @@ -885,64 +993,27 @@ int board_nand_init(struct nand_chip *nand) nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat; nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd; - - nand->cmd_ctrl = omap_nand_hwcontrol; - nand->options = NAND_NO_PADDING | NAND_CACHEPRG; + nand->priv = &bch_priv; + nand->cmd_ctrl = omap_nand_hwcontrol; + nand->options |= NAND_NO_PADDING | NAND_CACHEPRG; /* If we are 16 bit dev, our gpmc config tells us that */ if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) nand->options |= NAND_BUSWIDTH_16; nand->chip_delay = 100; + nand->ecc.layout = &omap_ecclayout; -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) -#ifdef CONFIG_AM33XX - /* AM33xx uses the ELM */ - /* required in case of BCH */ - elm_init(); -#else - /* - * Whereas other OMAP based SoC do not have the ELM, they use the BCH - * SW library. - */ - bch_priv.control = init_bch(13, 8, 0x201b /* hw polynominal */); - if (!bch_priv.control) { - puts("Could not init_bch()\n"); - return -ENODEV; - } -#endif - /* BCH info that will be correct for SPL or overridden otherwise. */ - nand->priv = &bch_priv; -#endif - - /* Default ECC mode */ -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_bch8_nand_oob; - nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; - nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; - nand->ecc.strength = 8; - nand->ecc.hwctl = omap_enable_ecc_bch; - nand->ecc.correct = omap_correct_data_bch; - nand->ecc.calculate = omap_calculate_ecc_bch; -#ifdef CONFIG_AM33XX - nand->ecc.read_page = omap_read_page_bch; -#endif - omap_hwecc_init_bch(nand, NAND_ECC_READ); -#else -#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC) - nand->ecc.mode = NAND_ECC_SOFT; + /* select ECC scheme */ +#if defined(CONFIG_NAND_OMAP_ECCSCHEME) + err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME, + CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE); #else - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_nand_oob; - nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; - nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; - nand->ecc.hwctl = omap_enable_hwecc; - nand->ecc.correct = omap_correct_data; - nand->ecc.calculate = omap_calculate_ecc; - nand->ecc.strength = 1; - omap_hwecc_init(nand); -#endif + /* pagesize and oobsize are not required to configure sw ecc-scheme */ + err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW, + 0, 0); #endif + if (err) + return err; #ifdef CONFIG_SPL_BUILD if (nand->options & NAND_BUSWIDTH_16) diff --git a/drivers/mtd/onenand/onenand_base.c b/drivers/mtd/onenand/onenand_base.c index 067f8ef18..979e4af7c 100644 --- a/drivers/mtd/onenand/onenand_base.c +++ b/drivers/mtd/onenand/onenand_base.c @@ -761,7 +761,8 @@ static int onenand_transfer_auto_oob(struct mtd_info *mtd, uint8_t *buf, uint8_t *oob_buf = this->oob_buf; free = this->ecclayout->oobfree; - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && free->length; i++, free++) { + for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE && free->length; + i++, free++) { if (readcol >= lastgap) readcol += free->offset - lastgap; if (readend >= lastgap) @@ -770,7 +771,8 @@ static int onenand_transfer_auto_oob(struct mtd_info *mtd, uint8_t *buf, } this->read_bufferram(mtd, 0, ONENAND_SPARERAM, oob_buf, 0, mtd->oobsize); free = this->ecclayout->oobfree; - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && free->length; i++, free++) { + for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE && free->length; + i++, free++) { int free_end = free->offset + free->length; if (free->offset < readend && free_end > readcol) { int st = max_t(int,free->offset,readcol); @@ -1356,7 +1358,8 @@ static int onenand_fill_auto_oob(struct mtd_info *mtd, u_char *oob_buf, unsigned int i; free = this->ecclayout->oobfree; - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && free->length; i++, free++) { + for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE && free->length; + i++, free++) { if (writecol >= lastgap) writecol += free->offset - lastgap; if (writeend >= lastgap) @@ -1364,7 +1367,8 @@ static int onenand_fill_auto_oob(struct mtd_info *mtd, u_char *oob_buf, lastgap = free->offset + free->length; } free = this->ecclayout->oobfree; - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && free->length; i++, free++) { + for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE && free->length; + i++, free++) { int free_end = free->offset + free->length; if (free->offset < writeend && free_end > writecol) { int st = max_t(int,free->offset,writecol); @@ -2750,7 +2754,8 @@ int onenand_scan(struct mtd_info *mtd, int maxchips) * the out of band area */ this->ecclayout->oobavail = 0; - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && + + for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE && this->ecclayout->oobfree[i].length; i++) this->ecclayout->oobavail += this->ecclayout->oobfree[i].length; diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile index 1bbeb7da3..26483a23f 100644 --- a/drivers/mtd/spi/Makefile +++ b/drivers/mtd/spi/Makefile @@ -13,4 +13,5 @@ endif obj-$(CONFIG_CMD_SF) += sf.o obj-$(CONFIG_SPI_FLASH) += sf_probe.o sf_ops.o obj-$(CONFIG_SPI_FRAM_RAMTRON) += ramtron.o +obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o obj-$(CONFIG_SPI_M95XXX) += eeprom_m95xxx.o diff --git a/drivers/mtd/spi/fsl_espi_spl.c b/drivers/mtd/spi/fsl_espi_spl.c index 6263d8c22..e5ac79b95 100644 --- a/drivers/mtd/spi/fsl_espi_spl.c +++ b/drivers/mtd/spi/fsl_espi_spl.c @@ -31,6 +31,10 @@ void spi_boot(void) hang(); } +#ifdef CONFIG_FSL_CORENET + offset = CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS; + code_len = CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE; +#else /* * Load U-Boot image from SPI flash into RAM */ @@ -50,6 +54,7 @@ void spi_boot(void) code_len = *(u32 *)(buf + ESPI_BOOT_IMAGE_SIZE); /* Skip spl code */ code_len = code_len - CONFIG_SPL_MAX_SIZE; +#endif /* copy code to DDR */ spi_flash_read(flash, offset, code_len, (void *)CONFIG_SYS_SPI_FLASH_U_BOOT_DST); diff --git a/drivers/mtd/spi/sandbox.c b/drivers/mtd/spi/sandbox.c new file mode 100644 index 000000000..a62ef4cbb --- /dev/null +++ b/drivers/mtd/spi/sandbox.c @@ -0,0 +1,483 @@ +/* + * Simulate a SPI flash + * + * Copyright (c) 2011-2013 The Chromium OS Authors. + * See file CREDITS for list of people who contributed to this + * project. + * + * Licensed under the GPL-2 or later. + */ + +#include <common.h> +#include <malloc.h> +#include <spi.h> +#include <os.h> + +#include <spi_flash.h> +#include "sf_internal.h" + +#include <asm/getopt.h> +#include <asm/spi.h> +#include <asm/state.h> + +/* + * The different states that our SPI flash transitions between. + * We need to keep track of this across multiple xfer calls since + * the SPI bus could possibly call down into us multiple times. + */ +enum sandbox_sf_state { + SF_CMD, /* default state -- we're awaiting a command */ + SF_ID, /* read the flash's (jedec) ID code */ + SF_ADDR, /* processing the offset in the flash to read/etc... */ + SF_READ, /* reading data from the flash */ + SF_WRITE, /* writing data to the flash, i.e. page programming */ + SF_ERASE, /* erase the flash */ + SF_READ_STATUS, /* read the flash's status register */ + SF_READ_STATUS1, /* read the flash's status register upper 8 bits*/ +}; + +static const char *sandbox_sf_state_name(enum sandbox_sf_state state) +{ + static const char * const states[] = { + "CMD", "ID", "ADDR", "READ", "WRITE", "ERASE", "READ_STATUS", + }; + return states[state]; +} + +/* Bits for the status register */ +#define STAT_WIP (1 << 0) +#define STAT_WEL (1 << 1) + +/* Assume all SPI flashes have 3 byte addresses since they do atm */ +#define SF_ADDR_LEN 3 + +struct sandbox_spi_flash_erase_commands { + u8 cmd; + u32 size; +}; +#define IDCODE_LEN 5 +#define MAX_ERASE_CMDS 3 +struct sandbox_spi_flash_data { + const char *name; + u8 idcode[IDCODE_LEN]; + u32 size; + const struct sandbox_spi_flash_erase_commands + erase_cmds[MAX_ERASE_CMDS]; +}; + +/* Structure describing all the flashes we know how to emulate */ +static const struct sandbox_spi_flash_data sandbox_sf_flashes[] = { + { + "M25P16", { 0x20, 0x20, 0x15 }, (2 << 20), + { /* erase commands */ + { 0xd8, (64 << 10), }, /* sector */ + { 0xc7, (2 << 20), }, /* bulk */ + }, + }, + { + "W25Q32", { 0xef, 0x40, 0x16 }, (4 << 20), + { /* erase commands */ + { 0x20, (4 << 10), }, /* 4KB */ + { 0xd8, (64 << 10), }, /* sector */ + { 0xc7, (4 << 20), }, /* bulk */ + }, + }, + { + "W25Q128", { 0xef, 0x40, 0x18 }, (16 << 20), + { /* erase commands */ + { 0x20, (4 << 10), }, /* 4KB */ + { 0xd8, (64 << 10), }, /* sector */ + { 0xc7, (16 << 20), }, /* bulk */ + }, + }, +}; + +/* Used to quickly bulk erase backing store */ +static u8 sandbox_sf_0xff[0x1000]; + +/* Internal state data for each SPI flash */ +struct sandbox_spi_flash { + /* + * As we receive data over the SPI bus, our flash transitions + * between states. For example, we start off in the SF_CMD + * state where the first byte tells us what operation to perform + * (such as read or write the flash). But the operation itself + * can go through a few states such as first reading in the + * offset in the flash to perform the requested operation. + * Thus "state" stores the exact state that our machine is in + * while "cmd" stores the overall command we're processing. + */ + enum sandbox_sf_state state; + uint cmd; + const void *cmd_data; + /* Current position in the flash; used when reading/writing/etc... */ + uint off; + /* How many address bytes we've consumed */ + uint addr_bytes, pad_addr_bytes; + /* The current flash status (see STAT_XXX defines above) */ + u16 status; + /* Data describing the flash we're emulating */ + const struct sandbox_spi_flash_data *data; + /* The file on disk to serv up data from */ + int fd; +}; + +static int sandbox_sf_setup(void **priv, const char *spec) +{ + /* spec = idcode:file */ + struct sandbox_spi_flash *sbsf; + const char *file; + size_t i, len, idname_len; + const struct sandbox_spi_flash_data *data; + + file = strchr(spec, ':'); + if (!file) { + printf("sandbox_sf: unable to parse file\n"); + goto error; + } + idname_len = file - spec; + ++file; + + for (i = 0; i < ARRAY_SIZE(sandbox_sf_flashes); ++i) { + data = &sandbox_sf_flashes[i]; + len = strlen(data->name); + if (idname_len != len) + continue; + if (!memcmp(spec, data->name, len)) + break; + } + if (i == ARRAY_SIZE(sandbox_sf_flashes)) { + printf("sandbox_sf: unknown flash '%*s'\n", (int)idname_len, + spec); + goto error; + } + + if (sandbox_sf_0xff[0] == 0x00) + memset(sandbox_sf_0xff, 0xff, sizeof(sandbox_sf_0xff)); + + sbsf = calloc(sizeof(*sbsf), 1); + if (!sbsf) { + printf("sandbox_sf: out of memory\n"); + goto error; + } + + sbsf->fd = os_open(file, 02); + if (sbsf->fd == -1) { + free(sbsf); + printf("sandbox_sf: unable to open file '%s'\n", file); + goto error; + } + + sbsf->data = data; + + *priv = sbsf; + return 0; + + error: + return 1; +} + +static void sandbox_sf_free(void *priv) +{ + struct sandbox_spi_flash *sbsf = priv; + + os_close(sbsf->fd); + free(sbsf); +} + +static void sandbox_sf_cs_activate(void *priv) +{ + struct sandbox_spi_flash *sbsf = priv; + + debug("sandbox_sf: CS activated; state is fresh!\n"); + + /* CS is asserted, so reset state */ + sbsf->off = 0; + sbsf->addr_bytes = 0; + sbsf->pad_addr_bytes = 0; + sbsf->state = SF_CMD; + sbsf->cmd = SF_CMD; +} + +static void sandbox_sf_cs_deactivate(void *priv) +{ + debug("sandbox_sf: CS deactivated; cmd done processing!\n"); +} + +/* Figure out what command this stream is telling us to do */ +static int sandbox_sf_process_cmd(struct sandbox_spi_flash *sbsf, const u8 *rx, + u8 *tx) +{ + enum sandbox_sf_state oldstate = sbsf->state; + + /* We need to output a byte for the cmd byte we just ate */ + sandbox_spi_tristate(tx, 1); + + sbsf->cmd = rx[0]; + switch (sbsf->cmd) { + case CMD_READ_ID: + sbsf->state = SF_ID; + sbsf->cmd = SF_ID; + break; + case CMD_READ_ARRAY_FAST: + sbsf->pad_addr_bytes = 1; + case CMD_READ_ARRAY_SLOW: + case CMD_PAGE_PROGRAM: + state_addr: + sbsf->state = SF_ADDR; + break; + case CMD_WRITE_DISABLE: + debug(" write disabled\n"); + sbsf->status &= ~STAT_WEL; + break; + case CMD_READ_STATUS: + sbsf->state = SF_READ_STATUS; + break; + case CMD_READ_STATUS1: + sbsf->state = SF_READ_STATUS1; + break; + case CMD_WRITE_ENABLE: + debug(" write enabled\n"); + sbsf->status |= STAT_WEL; + break; + default: { + size_t i; + + /* handle erase commands first */ + for (i = 0; i < MAX_ERASE_CMDS; ++i) { + const struct sandbox_spi_flash_erase_commands * + erase_cmd = &sbsf->data->erase_cmds[i]; + + if (erase_cmd->cmd == 0x00) + continue; + if (sbsf->cmd != erase_cmd->cmd) + continue; + + sbsf->cmd_data = erase_cmd; + goto state_addr; + } + + debug(" cmd unknown: %#x\n", sbsf->cmd); + return 1; + } + } + + if (oldstate != sbsf->state) + debug(" cmd: transition to %s state\n", + sandbox_sf_state_name(sbsf->state)); + + return 0; +} + +int sandbox_erase_part(struct sandbox_spi_flash *sbsf, int size) +{ + int todo; + int ret; + + while (size > 0) { + todo = min(size, sizeof(sandbox_sf_0xff)); + ret = os_write(sbsf->fd, sandbox_sf_0xff, todo); + if (ret != todo) + return ret; + size -= todo; + } + + return 0; +} + +static int sandbox_sf_xfer(void *priv, const u8 *rx, u8 *tx, + uint bytes) +{ + struct sandbox_spi_flash *sbsf = priv; + uint cnt, pos = 0; + int ret; + + debug("sandbox_sf: state:%x(%s) bytes:%u\n", sbsf->state, + sandbox_sf_state_name(sbsf->state), bytes); + + if (sbsf->state == SF_CMD) { + /* Figure out the initial state */ + if (sandbox_sf_process_cmd(sbsf, rx, tx)) + return 1; + ++pos; + } + + /* Process the remaining data */ + while (pos < bytes) { + switch (sbsf->state) { + case SF_ID: { + u8 id; + + debug(" id: off:%u tx:", sbsf->off); + if (sbsf->off < IDCODE_LEN) + id = sbsf->data->idcode[sbsf->off]; + else + id = 0; + debug("%02x\n", id); + tx[pos++] = id; + ++sbsf->off; + break; + } + case SF_ADDR: + debug(" addr: bytes:%u rx:%02x ", sbsf->addr_bytes, + rx[pos]); + + if (sbsf->addr_bytes++ < SF_ADDR_LEN) + sbsf->off = (sbsf->off << 8) | rx[pos]; + debug("addr:%06x\n", sbsf->off); + + sandbox_spi_tristate(&tx[pos++], 1); + + /* See if we're done processing */ + if (sbsf->addr_bytes < + SF_ADDR_LEN + sbsf->pad_addr_bytes) + break; + + /* Next state! */ + if (os_lseek(sbsf->fd, sbsf->off, OS_SEEK_SET) < 0) { + puts("sandbox_sf: os_lseek() failed"); + return 1; + } + switch (sbsf->cmd) { + case CMD_READ_ARRAY_FAST: + case CMD_READ_ARRAY_SLOW: + sbsf->state = SF_READ; + break; + case CMD_PAGE_PROGRAM: + sbsf->state = SF_WRITE; + break; + default: + /* assume erase state ... */ + sbsf->state = SF_ERASE; + goto case_sf_erase; + } + debug(" cmd: transition to %s state\n", + sandbox_sf_state_name(sbsf->state)); + break; + case SF_READ: + /* + * XXX: need to handle exotic behavior: + * - reading past end of device + */ + + cnt = bytes - pos; + debug(" tx: read(%u)\n", cnt); + ret = os_read(sbsf->fd, tx + pos, cnt); + if (ret < 0) { + puts("sandbox_spi: os_read() failed\n"); + return 1; + } + pos += ret; + break; + case SF_READ_STATUS: + debug(" read status: %#x\n", sbsf->status); + cnt = bytes - pos; + memset(tx + pos, sbsf->status, cnt); + pos += cnt; + break; + case SF_READ_STATUS1: + debug(" read status: %#x\n", sbsf->status); + cnt = bytes - pos; + memset(tx + pos, sbsf->status >> 8, cnt); + pos += cnt; + break; + case SF_WRITE: + /* + * XXX: need to handle exotic behavior: + * - unaligned addresses + * - more than a page (256) worth of data + * - reading past end of device + */ + if (!(sbsf->status & STAT_WEL)) { + puts("sandbox_sf: write enable not set before write\n"); + goto done; + } + + cnt = bytes - pos; + debug(" rx: write(%u)\n", cnt); + sandbox_spi_tristate(&tx[pos], cnt); + ret = os_write(sbsf->fd, rx + pos, cnt); + if (ret < 0) { + puts("sandbox_spi: os_write() failed\n"); + return 1; + } + pos += ret; + sbsf->status &= ~STAT_WEL; + break; + case SF_ERASE: + case_sf_erase: { + const struct sandbox_spi_flash_erase_commands * + erase_cmd = sbsf->cmd_data; + + if (!(sbsf->status & STAT_WEL)) { + puts("sandbox_sf: write enable not set before erase\n"); + goto done; + } + + /* verify address is aligned */ + if (sbsf->off & (erase_cmd->size - 1)) { + debug(" sector erase: cmd:%#x needs align:%#x, but we got %#x\n", + erase_cmd->cmd, erase_cmd->size, + sbsf->off); + sbsf->status &= ~STAT_WEL; + goto done; + } + + debug(" sector erase addr: %u\n", sbsf->off); + + cnt = bytes - pos; + sandbox_spi_tristate(&tx[pos], cnt); + pos += cnt; + + /* + * TODO(vapier@gentoo.org): latch WIP in status, and + * delay before clearing it ? + */ + ret = sandbox_erase_part(sbsf, erase_cmd->size); + sbsf->status &= ~STAT_WEL; + if (ret) { + debug("sandbox_sf: Erase failed\n"); + goto done; + } + goto done; + } + default: + debug(" ??? no idea what to do ???\n"); + goto done; + } + } + + done: + return pos == bytes ? 0 : 1; +} + +static const struct sandbox_spi_emu_ops sandbox_sf_ops = { + .setup = sandbox_sf_setup, + .free = sandbox_sf_free, + .cs_activate = sandbox_sf_cs_activate, + .cs_deactivate = sandbox_sf_cs_deactivate, + .xfer = sandbox_sf_xfer, +}; + +static int sandbox_cmdline_cb_spi_sf(struct sandbox_state *state, + const char *arg) +{ + unsigned long bus, cs; + const char *spec = sandbox_spi_parse_spec(arg, &bus, &cs); + + if (!spec) + return 1; + + /* + * It is safe to not make a copy of 'spec' because it comes from the + * command line. + * + * TODO(sjg@chromium.org): It would be nice if we could parse the + * spec here, but the problem is that no U-Boot init has been done + * yet. Perhaps we can figure something out. + */ + state->spi[bus][cs].ops = &sandbox_sf_ops; + state->spi[bus][cs].spec = spec; + return 0; +} +SANDBOX_CMDLINE_OPT(spi_sf, 1, "connect a SPI flash: <bus>:<cs>:<id>:<file>"); diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h index 732ddf836..d291746ed 100644 --- a/drivers/mtd/spi/sf_internal.h +++ b/drivers/mtd/spi/sf_internal.h @@ -28,6 +28,7 @@ #define CMD_PAGE_PROGRAM 0x02 #define CMD_WRITE_DISABLE 0x04 #define CMD_READ_STATUS 0x05 +#define CMD_READ_STATUS1 0x35 #define CMD_WRITE_ENABLE 0x06 #define CMD_READ_CONFIG 0x35 #define CMD_FLAG_STATUS 0x70 diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c index 5eb8ffe84..c1eb75489 100644 --- a/drivers/mtd/spi/sf_probe.c +++ b/drivers/mtd/spi/sf_probe.c @@ -13,6 +13,7 @@ #include <malloc.h> #include <spi.h> #include <spi_flash.h> +#include <asm/io.h> #include "sf_internal.h" @@ -279,22 +280,19 @@ int spi_flash_decode_fdt(const void *blob, struct spi_flash *flash) debug("%s: Memory map must cover entire device\n", __func__); return -1; } - flash->memory_map = (void *)addr; + flash->memory_map = map_sysmem(addr, size); return 0; } #endif /* CONFIG_OF_CONTROL */ -struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs, - unsigned int max_hz, unsigned int spi_mode) +static struct spi_flash *spi_flash_probe_slave(struct spi_slave *spi) { - struct spi_slave *spi; struct spi_flash *flash = NULL; u8 idcode[5]; int ret; /* Setup spi_slave */ - spi = spi_setup_slave(bus, cs, max_hz, spi_mode); if (!spi) { printf("SF: Failed to set up slave\n"); return NULL; @@ -358,6 +356,26 @@ err_claim_bus: return NULL; } +struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int spi_mode) +{ + struct spi_slave *spi; + + spi = spi_setup_slave(bus, cs, max_hz, spi_mode); + return spi_flash_probe_slave(spi); +} + +#ifdef CONFIG_OF_SPI_FLASH +struct spi_flash *spi_flash_probe_fdt(const void *blob, int slave_node, + int spi_node) +{ + struct spi_slave *spi; + + spi = spi_setup_slave_fdt(blob, slave_node, spi_node); + return spi_flash_probe_slave(spi); +} +#endif + void spi_flash_free(struct spi_flash *flash) { spi_free_slave(flash->spi); diff --git a/drivers/net/at91_emac.c b/drivers/net/at91_emac.c index 73612ea06..64d4c56ac 100644 --- a/drivers/net/at91_emac.c +++ b/drivers/net/at91_emac.c @@ -10,19 +10,10 @@ #include <common.h> #include <asm/io.h> -#ifndef CONFIG_AT91_LEGACY #include <asm/arch/hardware.h> #include <asm/arch/at91_emac.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_pio.h> -#else -/* remove next 5 lines, if all RM9200 boards convert to at91 arch */ -#include <asm/arch-at91/at91rm9200.h> -#include <asm/arch-at91/hardware.h> -#include <asm/arch-at91/at91_emac.h> -#include <asm/arch-at91/at91_pmc.h> -#include <asm/arch-at91/at91_pio.h> -#endif #include <net.h> #include <netdev.h> #include <malloc.h> diff --git a/drivers/net/cpsw.c b/drivers/net/cpsw.c index 39240d966..50167aab6 100644 --- a/drivers/net/cpsw.c +++ b/drivers/net/cpsw.c @@ -914,7 +914,7 @@ static int cpsw_recv(struct eth_device *dev) void *buffer; int len; - cpsw_update_link(priv); + cpsw_check_link(priv); while (cpdma_process(priv, &priv->rx_chan, &buffer, &len) >= 0) { invalidate_dcache_range((unsigned long)buffer, diff --git a/drivers/net/designware.c b/drivers/net/designware.c index 8413d5776..22155b4d9 100644 --- a/drivers/net/designware.c +++ b/drivers/net/designware.c @@ -96,7 +96,7 @@ static int mac_reset(struct eth_device *dev) ulong start; int timeout = CONFIG_MACRESET_TIMEOUT; - writel(DMAMAC_SRST, &dma_p->busmode); + writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode); if (priv->interface != PHY_INTERFACE_MODE_RGMII) writel(MII_PORTSELECT, &mac_p->conf); diff --git a/drivers/net/designware.h b/drivers/net/designware.h index e80002a0e..5440c9215 100644 --- a/drivers/net/designware.h +++ b/drivers/net/designware.h @@ -112,7 +112,7 @@ struct dmamacdescr { u32 dmamac_cntl; void *dmamac_addr; struct dmamacdescr *dmamac_next; -}; +} __aligned(16); /* * txrx_status definitions @@ -224,8 +224,7 @@ struct dw_eth_dev { u32 tx_currdescnum; u32 rx_currdescnum; u32 phy_configured; - int link_printed; - u32 padding; + u32 link_printed; struct dmamacdescr tx_mac_descrtable[CONFIG_TX_DESCR_NUM]; struct dmamacdescr rx_mac_descrtable[CONFIG_RX_DESCR_NUM]; @@ -237,7 +236,7 @@ struct dw_eth_dev { struct eth_dma_regs *dma_regs_p; struct eth_device *dev; -} __attribute__ ((aligned(8))); +}; /* Speed specific definitions */ #define SPEED_10M 1 diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index f7170e055..b68d808c7 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -342,6 +342,15 @@ static int dm9000_init(struct eth_device *dev, bd_t *bd) DM9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS); printf("MAC: %pM\n", dev->enetaddr); + if (!is_valid_ether_addr(dev->enetaddr)) { +#ifdef CONFIG_RANDOM_MACADDR + printf("Bad MAC address (uninitialized EEPROM?), randomizing\n"); + eth_random_enetaddr(dev->enetaddr); + printf("MAC: %pM\n", dev->enetaddr); +#else + printf("WARNING: Bad MAC address (uninitialized EEPROM?)\n"); +#endif + } /* fill device MAC address registers */ for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++) diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index 57aa53dba..9a66e68ae 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -114,12 +114,13 @@ static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, static int32_t e1000_phy_hw_reset(struct e1000_hw *hw); static int e1000_phy_reset(struct e1000_hw *hw); static int e1000_detect_gig_phy(struct e1000_hw *hw); -static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); static void e1000_set_media_type(struct e1000_hw *hw); static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); +#ifndef CONFIG_E1000_NO_NVM +static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); @@ -885,6 +886,7 @@ static int e1000_validate_eeprom_checksum(struct e1000_hw *hw) return -E1000_ERR_EEPROM; } +#endif /* CONFIG_E1000_NO_NVM */ /***************************************************************************** * Set PHY to class A mode @@ -897,6 +899,7 @@ static int e1000_validate_eeprom_checksum(struct e1000_hw *hw) static int32_t e1000_set_phy_mode(struct e1000_hw *hw) { +#ifndef CONFIG_E1000_NO_NVM int32_t ret_val; uint16_t eeprom_data; @@ -923,10 +926,11 @@ e1000_set_phy_mode(struct e1000_hw *hw) hw->phy_reset_disable = false; } } - +#endif return E1000_SUCCESS; } +#ifndef CONFIG_E1000_NO_NVM /*************************************************************************** * * Obtaining software semaphore bit (SMBI) before resetting PHY. @@ -965,6 +969,7 @@ e1000_get_software_semaphore(struct e1000_hw *hw) return E1000_SUCCESS; } +#endif /*************************************************************************** * This function clears HW semaphore bits. @@ -977,6 +982,7 @@ e1000_get_software_semaphore(struct e1000_hw *hw) static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) { +#ifndef CONFIG_E1000_NO_NVM uint32_t swsm; DEBUGFUNC(); @@ -991,6 +997,7 @@ e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) } else swsm &= ~(E1000_SWSM_SWESMBI); E1000_WRITE_REG(hw, SWSM, swsm); +#endif } /*************************************************************************** @@ -1007,6 +1014,7 @@ e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) { +#ifndef CONFIG_E1000_NO_NVM int32_t timeout; uint32_t swsm; @@ -1043,7 +1051,7 @@ e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) "SWESMBI bit is set.\n"); return -E1000_ERR_EEPROM; } - +#endif return E1000_SUCCESS; } @@ -1097,6 +1105,7 @@ static bool e1000_is_second_port(struct e1000_hw *hw) } } +#ifndef CONFIG_E1000_NO_NVM /****************************************************************************** * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the * second function of dual function devices @@ -1136,6 +1145,7 @@ e1000_read_mac_addr(struct eth_device *nic) #endif return 0; } +#endif /****************************************************************************** * Initializes receive address filters. @@ -1764,9 +1774,11 @@ static int e1000_setup_link(struct eth_device *nic) { struct e1000_hw *hw = nic->priv; - uint32_t ctrl_ext; int32_t ret_val; +#ifndef CONFIG_E1000_NO_NVM + uint32_t ctrl_ext; uint16_t eeprom_data; +#endif DEBUGFUNC(); @@ -1775,6 +1787,7 @@ e1000_setup_link(struct eth_device *nic) if (e1000_check_phy_reset_block(hw)) return E1000_SUCCESS; +#ifndef CONFIG_E1000_NO_NVM /* Read and store word 0x0F of the EEPROM. This word contains bits * that determine the hardware's default PAUSE (flow control) mode, * a bit that determines whether the HW defaults to enabling or @@ -1788,7 +1801,7 @@ e1000_setup_link(struct eth_device *nic) DEBUGOUT("EEPROM Read Error\n"); return -E1000_ERR_EEPROM; } - +#endif if (hw->fc == e1000_fc_default) { switch (hw->mac_type) { case e1000_ich8lan: @@ -1797,6 +1810,7 @@ e1000_setup_link(struct eth_device *nic) hw->fc = e1000_fc_full; break; default: +#ifndef CONFIG_E1000_NO_NVM ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); if (ret_val) { @@ -1809,6 +1823,7 @@ e1000_setup_link(struct eth_device *nic) EEPROM_WORD0F_ASM_DIR) hw->fc = e1000_fc_tx_pause; else +#endif hw->fc = e1000_fc_full; break; } @@ -1828,6 +1843,7 @@ e1000_setup_link(struct eth_device *nic) DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc); +#ifndef CONFIG_E1000_NO_NVM /* Take the 4 bits from EEPROM word 0x0F that determine the initial * polarity value for the SW controlled pins, and setup the * Extended Device Control reg with that info. @@ -1840,6 +1856,7 @@ e1000_setup_link(struct eth_device *nic) SWDPIO__EXT_SHIFT); E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); } +#endif /* Call the necessary subroutine to configure the link. */ ret_val = (hw->media_type == e1000_media_type_fiber) ? @@ -5196,6 +5213,7 @@ e1000_initialize(bd_t * bis) e1000_reset_hw(hw); list_add_tail(&hw->list_node, &e1000_hw_list); +#ifndef CONFIG_E1000_NO_NVM /* Validate the EEPROM and get chipset information */ #if !defined(CONFIG_MVBC_1G) if (e1000_init_eeprom_params(hw)) { @@ -5206,11 +5224,17 @@ e1000_initialize(bd_t * bis) continue; #endif e1000_read_mac_addr(nic); +#endif e1000_get_bus_type(hw); +#ifndef CONFIG_E1000_NO_NVM printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n ", nic->enetaddr[0], nic->enetaddr[1], nic->enetaddr[2], nic->enetaddr[3], nic->enetaddr[4], nic->enetaddr[5]); +#else + memset(nic->enetaddr, 0, 6); + printf("e1000: no NVM\n"); +#endif /* Set up the function pointers and register the device */ nic->init = e1000_init; diff --git a/drivers/net/e1000.h b/drivers/net/e1000.h index 25884f5bc..ff87af2ef 100644 --- a/drivers/net/e1000.h +++ b/drivers/net/e1000.h @@ -63,11 +63,14 @@ struct e1000_hw_stats; /* Internal E1000 helper functions */ struct e1000_hw *e1000_find_card(unsigned int cardnum); + +#ifndef CONFIG_E1000_NO_NVM int32_t e1000_acquire_eeprom(struct e1000_hw *hw); void e1000_standby_eeprom(struct e1000_hw *hw); void e1000_release_eeprom(struct e1000_hw *hw); void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t *eecd); void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t *eecd); +#endif #ifdef CONFIG_E1000_SPI int do_e1000_spi(cmd_tbl_t *cmdtp, struct e1000_hw *hw, @@ -1019,6 +1022,7 @@ struct e1000_hw_stats { uint64_t tsctfc; }; +#ifndef CONFIG_E1000_NO_NVM struct e1000_eeprom_info { e1000_eeprom_type type; uint16_t word_size; @@ -1029,6 +1033,7 @@ e1000_eeprom_type type; bool use_eerd; bool use_eewr; }; +#endif typedef enum { e1000_smart_speed_default = 0, @@ -1081,10 +1086,14 @@ struct e1000_hw { uint32_t io_base; #endif uint32_t asf_firmware_present; +#ifndef CONFIG_E1000_NO_NVM uint32_t eeprom_semaphore_present; +#endif uint32_t swfw_sync_present; uint32_t swfwhw_semaphore_present; +#ifndef CONFIG_E1000_NO_NVM struct e1000_eeprom_info eeprom; +#endif e1000_ms_type master_slave; e1000_ms_type original_master_slave; e1000_ffe_config ffe_config_state; diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index bec86c16c..ee5d76893 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -4,7 +4,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_FMAN_ENET obj-y += dtsec.o obj-y += eth.o obj-y += fm.o @@ -26,8 +25,12 @@ obj-$(CONFIG_PPC_P4080) += p4080.o obj-$(CONFIG_PPC_P5020) += p5020.o obj-$(CONFIG_PPC_P5040) += p5040.o obj-$(CONFIG_PPC_T1040) += t1040.o +obj-$(CONFIG_PPC_T1042) += t1040.o +obj-$(CONFIG_PPC_T1020) += t1040.o +obj-$(CONFIG_PPC_T1022) += t1040.o +obj-$(CONFIG_PPC_T2080) += t2080.o +obj-$(CONFIG_PPC_T2081) += t2080.o obj-$(CONFIG_PPC_T4240) += t4240.o obj-$(CONFIG_PPC_T4160) += t4240.o obj-$(CONFIG_PPC_B4420) += b4860.o obj-$(CONFIG_PPC_B4860) += b4860.o -endif diff --git a/drivers/net/fm/eth.c b/drivers/net/fm/eth.c index cb099cd84..218a5ed17 100644 --- a/drivers/net/fm/eth.c +++ b/drivers/net/fm/eth.c @@ -557,8 +557,16 @@ static int fm_eth_init_mac(struct fm_eth *fm_eth, struct ccsr_fman *reg) num = fm_eth->num; #ifdef CONFIG_SYS_FMAN_V3 - if (fm_eth->type == FM_ETH_10G_E) - num += 8; + if (fm_eth->type == FM_ETH_10G_E) { + /* 10GEC1/10GEC2 use mEMAC9/mEMAC10 + * 10GEC3/10GEC4 use mEMAC1/mEMAC2 + * so it needs to change the num. + */ + if (fm_eth->num >= 2) + num -= 2; + else + num += 8; + } base = ®->memac[num].fm_memac; phyregs = ®->memac[num].fm_memac_mdio; #else diff --git a/drivers/net/fm/fm.h b/drivers/net/fm/fm.h index 3ec49a4f3..43de114b5 100644 --- a/drivers/net/fm/fm.h +++ b/drivers/net/fm/fm.h @@ -18,9 +18,11 @@ #define RX_PORT_1G_BASE 0x08 #define MAX_NUM_RX_PORT_1G CONFIG_SYS_NUM_FM1_DTSEC #define RX_PORT_10G_BASE 0x10 +#define RX_PORT_10G_BASE2 0x08 #define TX_PORT_1G_BASE 0x28 #define MAX_NUM_TX_PORT_1G CONFIG_SYS_NUM_FM1_DTSEC #define TX_PORT_10G_BASE 0x30 +#define TX_PORT_10G_BASE2 0x28 #define MIIM_TIMEOUT 0xFFFF struct fm_muram { diff --git a/drivers/net/fm/init.c b/drivers/net/fm/init.c index 35edd7ad9..cd787f4ee 100644 --- a/drivers/net/fm/init.c +++ b/drivers/net/fm/init.c @@ -64,6 +64,12 @@ struct fm_eth_info fm_info[] = { #if (CONFIG_SYS_NUM_FM1_10GEC >= 2) FM_TGEC_INFO_INITIALIZER(1, 2), #endif +#if (CONFIG_SYS_NUM_FM1_10GEC >= 3) + FM_TGEC_INFO_INITIALIZER2(1, 3), +#endif +#if (CONFIG_SYS_NUM_FM1_10GEC >= 4) + FM_TGEC_INFO_INITIALIZER2(1, 4), +#endif #if (CONFIG_SYS_NUM_FM2_10GEC >= 1) FM_TGEC_INFO_INITIALIZER(2, 1), #endif @@ -239,10 +245,14 @@ static void ft_fixup_port(void *blob, struct fm_eth_info *info, char *prop) * FM1_10GEC1 is enabled and FM1_DTSEC9 is disabled, ensure that the * dual-role MAC is not disabled, ditto for other dual-role MACs. */ - if (((info->port == FM1_DTSEC9) && (PORT_IS_ENABLED(FM1_10GEC1))) || - ((info->port == FM1_DTSEC10) && (PORT_IS_ENABLED(FM1_10GEC2))) || - ((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC9))) || - ((info->port == FM1_10GEC2) && (PORT_IS_ENABLED(FM1_DTSEC10))) + if (((info->port == FM1_DTSEC9) && (PORT_IS_ENABLED(FM1_10GEC1))) || + ((info->port == FM1_DTSEC10) && (PORT_IS_ENABLED(FM1_10GEC2))) || + ((info->port == FM1_DTSEC1) && (PORT_IS_ENABLED(FM1_10GEC3))) || + ((info->port == FM1_DTSEC2) && (PORT_IS_ENABLED(FM1_10GEC4))) || + ((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC9))) || + ((info->port == FM1_10GEC2) && (PORT_IS_ENABLED(FM1_DTSEC10))) || + ((info->port == FM1_10GEC3) && (PORT_IS_ENABLED(FM1_DTSEC1))) || + ((info->port == FM1_10GEC4) && (PORT_IS_ENABLED(FM1_DTSEC2))) #if (CONFIG_SYS_NUM_FMAN == 2) || ((info->port == FM2_DTSEC9) && (PORT_IS_ENABLED(FM2_10GEC1))) || diff --git a/drivers/net/fm/t2080.c b/drivers/net/fm/t2080.c new file mode 100644 index 000000000..b5c1e9f76 --- /dev/null +++ b/drivers/net/fm/t2080.c @@ -0,0 +1,91 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * Shengzhou Liu <Shengzhou.Liu@freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_serdes.h> + +u32 port_to_devdisr[] = { + [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1, + [FM1_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC1_2, + [FM1_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC1_3, + [FM1_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC1_4, + [FM1_DTSEC5] = FSL_CORENET_DEVDISR2_DTSEC1_5, + [FM1_DTSEC6] = FSL_CORENET_DEVDISR2_DTSEC1_6, + [FM1_DTSEC9] = FSL_CORENET_DEVDISR2_DTSEC1_9, + [FM1_DTSEC10] = FSL_CORENET_DEVDISR2_DTSEC1_10, + [FM1_10GEC1] = FSL_CORENET_DEVDISR2_10GEC1_1, + [FM1_10GEC2] = FSL_CORENET_DEVDISR2_10GEC1_2, + [FM1_10GEC3] = FSL_CORENET_DEVDISR2_10GEC1_3, + [FM1_10GEC4] = FSL_CORENET_DEVDISR2_10GEC1_4, +}; + +static int is_device_disabled(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 devdisr2 = in_be32(&gur->devdisr2); + + return port_to_devdisr[port] & devdisr2; +} + +void fman_disable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + +phy_interface_t fman_port_enet_if(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 rcwsr13 = in_be32(&gur->rcwsr[13]); + + if (is_device_disabled(port)) + return PHY_INTERFACE_MODE_NONE; + + if ((port == FM1_10GEC1 || port == FM1_10GEC2 || + port == FM1_10GEC3 || port == FM1_10GEC4) && + ((is_serdes_configured(XAUI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC1)) || + (is_serdes_configured(XFI_FM1_MAC2)) || + (is_serdes_configured(XFI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC10)))) + return PHY_INTERFACE_MODE_XGMII; + + if ((port == FM1_DTSEC3) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) == + FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + if ((port == FM1_DTSEC4) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) == + FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + if ((port == FM1_DTSEC10) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) == + FSL_CORENET_RCWSR13_EC2_DTSEC10_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + switch (port) { + case FM1_DTSEC1: + case FM1_DTSEC2: + case FM1_DTSEC3: + case FM1_DTSEC4: + case FM1_DTSEC5: + case FM1_DTSEC6: + case FM1_DTSEC9: + case FM1_DTSEC10: + if (is_serdes_configured(SGMII_FM1_DTSEC1 + port - FM1_DTSEC1)) + return PHY_INTERFACE_MODE_SGMII; + break; + default: + return PHY_INTERFACE_MODE_NONE; + } + + return PHY_INTERFACE_MODE_NONE; +} diff --git a/drivers/net/fsl_mdio.c b/drivers/net/fsl_mdio.c index ce36bd7a3..1d88e6504 100644 --- a/drivers/net/fsl_mdio.c +++ b/drivers/net/fsl_mdio.c @@ -1,5 +1,5 @@ /* - * Copyright 2009-2010 Freescale Semiconductor, Inc. + * Copyright 2009-2010, 2013 Freescale Semiconductor, Inc. * Jun-jie Zhang <b18070@freescale.com> * Mingkai Hu <Mingkai.hu@freescale.com> * @@ -13,7 +13,7 @@ #include <asm/errno.h> #include <asm/fsl_enet.h> -void tsec_local_mdio_write(struct tsec_mii_mng *phyregs, int port_addr, +void tsec_local_mdio_write(struct tsec_mii_mng __iomem *phyregs, int port_addr, int dev_addr, int regnum, int value) { int timeout = 1000000; @@ -26,7 +26,7 @@ void tsec_local_mdio_write(struct tsec_mii_mng *phyregs, int port_addr, ; } -int tsec_local_mdio_read(struct tsec_mii_mng *phyregs, int port_addr, +int tsec_local_mdio_read(struct tsec_mii_mng __iomem *phyregs, int port_addr, int dev_addr, int regnum) { int value; @@ -57,7 +57,8 @@ int tsec_local_mdio_read(struct tsec_mii_mng *phyregs, int port_addr, static int fsl_pq_mdio_reset(struct mii_dev *bus) { - struct tsec_mii_mng *regs = bus->priv; + struct tsec_mii_mng __iomem *regs = + (struct tsec_mii_mng __iomem *)bus->priv; /* Reset MII (due to new addresses) */ out_be32(®s->miimcfg, MIIMCFG_RESET_MGMT); @@ -72,7 +73,8 @@ static int fsl_pq_mdio_reset(struct mii_dev *bus) int tsec_phy_read(struct mii_dev *bus, int addr, int dev_addr, int regnum) { - struct tsec_mii_mng *phyregs = bus->priv; + struct tsec_mii_mng __iomem *phyregs = + (struct tsec_mii_mng __iomem *)bus->priv; return tsec_local_mdio_read(phyregs, addr, dev_addr, regnum); } @@ -80,7 +82,8 @@ int tsec_phy_read(struct mii_dev *bus, int addr, int dev_addr, int regnum) int tsec_phy_write(struct mii_dev *bus, int addr, int dev_addr, int regnum, u16 value) { - struct tsec_mii_mng *phyregs = bus->priv; + struct tsec_mii_mng __iomem *phyregs = + (struct tsec_mii_mng __iomem *)bus->priv; tsec_local_mdio_write(phyregs, addr, dev_addr, regnum, value); @@ -101,7 +104,7 @@ int fsl_pq_mdio_init(bd_t *bis, struct fsl_pq_mdio_info *info) bus->reset = fsl_pq_mdio_reset; sprintf(bus->name, info->name); - bus->priv = info->regs; + bus->priv = (void *)info->regs; return mdio_register(bus); } diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c index 6c901d1ea..0cd06b6a6 100644 --- a/drivers/net/mvgbe.c +++ b/drivers/net/mvgbe.c @@ -420,8 +420,9 @@ static int mvgbe_init(struct eth_device *dev) { struct mvgbe_device *dmvgbe = to_mvgbe(dev); struct mvgbe_registers *regs = dmvgbe->regs; -#if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \ - && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN) +#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) && \ + !defined(CONFIG_PHYLIB) && \ + defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN) int i; #endif /* setup RX rings */ diff --git a/drivers/net/npe/Makefile b/drivers/net/npe/Makefile index 7fa5ea635..077925521 100644 --- a/drivers/net/npe/Makefile +++ b/drivers/net/npe/Makefile @@ -8,9 +8,8 @@ LOCAL_CFLAGS += -I$(TOPDIR)/drivers/net/npe/include -DCONFIG_IXP425_COMPONENT_ETHDB -D__linux CFLAGS += $(LOCAL_CFLAGS) CPPFLAGS += $(LOCAL_CFLAGS) # needed for depend -HOSTCFLAGS += $(LOCAL_CFLAGS) -obj-$(CONFIG_IXP4XX_NPE) := npe.o \ +obj-y := npe.o \ miiphy.o \ IxOsalBufferMgt.o \ IxOsalIoMem.o \ diff --git a/drivers/net/pcnet.c b/drivers/net/pcnet.c index 283cb48b4..71a311071 100644 --- a/drivers/net/pcnet.c +++ b/drivers/net/pcnet.c @@ -89,39 +89,39 @@ static pcnet_priv_t *lp; #define PCNET_RESET 0x14 #define PCNET_BDP 0x16 -static u16 pcnet_read_csr (struct eth_device *dev, int index) +static u16 pcnet_read_csr(struct eth_device *dev, int index) { - outw (index, dev->iobase + PCNET_RAP); - return inw (dev->iobase + PCNET_RDP); + outw(index, dev->iobase + PCNET_RAP); + return inw(dev->iobase + PCNET_RDP); } -static void pcnet_write_csr (struct eth_device *dev, int index, u16 val) +static void pcnet_write_csr(struct eth_device *dev, int index, u16 val) { - outw (index, dev->iobase + PCNET_RAP); - outw (val, dev->iobase + PCNET_RDP); + outw(index, dev->iobase + PCNET_RAP); + outw(val, dev->iobase + PCNET_RDP); } -static u16 pcnet_read_bcr (struct eth_device *dev, int index) +static u16 pcnet_read_bcr(struct eth_device *dev, int index) { - outw (index, dev->iobase + PCNET_RAP); - return inw (dev->iobase + PCNET_BDP); + outw(index, dev->iobase + PCNET_RAP); + return inw(dev->iobase + PCNET_BDP); } -static void pcnet_write_bcr (struct eth_device *dev, int index, u16 val) +static void pcnet_write_bcr(struct eth_device *dev, int index, u16 val) { - outw (index, dev->iobase + PCNET_RAP); - outw (val, dev->iobase + PCNET_BDP); + outw(index, dev->iobase + PCNET_RAP); + outw(val, dev->iobase + PCNET_BDP); } -static void pcnet_reset (struct eth_device *dev) +static void pcnet_reset(struct eth_device *dev) { - inw (dev->iobase + PCNET_RESET); + inw(dev->iobase + PCNET_RESET); } -static int pcnet_check (struct eth_device *dev) +static int pcnet_check(struct eth_device *dev) { - outw (88, dev->iobase + PCNET_RAP); - return (inw (dev->iobase + PCNET_RAP) == 88); + outw(88, dev->iobase + PCNET_RAP); + return inw(dev->iobase + PCNET_RAP) == 88; } static int pcnet_init (struct eth_device *dev, bd_t * bis); @@ -139,63 +139,64 @@ static struct pci_device_id supported[] = { }; -int pcnet_initialize (bd_t * bis) +int pcnet_initialize(bd_t *bis) { pci_dev_t devbusfn; struct eth_device *dev; u16 command, status; int dev_nr = 0; - PCNET_DEBUG1 ("\npcnet_initialize...\n"); + PCNET_DEBUG1("\npcnet_initialize...\n"); for (dev_nr = 0;; dev_nr++) { /* * Find the PCnet PCI device(s). */ - if ((devbusfn = pci_find_devices (supported, dev_nr)) < 0) { + devbusfn = pci_find_devices(supported, dev_nr); + if (devbusfn < 0) break; - } /* * Allocate and pre-fill the device structure. */ - dev = (struct eth_device *) malloc (sizeof *dev); + dev = (struct eth_device *)malloc(sizeof(*dev)); if (!dev) { printf("pcnet: Can not allocate memory\n"); break; } memset(dev, 0, sizeof(*dev)); - dev->priv = (void *) devbusfn; - sprintf (dev->name, "pcnet#%d", dev_nr); + dev->priv = (void *)devbusfn; + sprintf(dev->name, "pcnet#%d", dev_nr); /* * Setup the PCI device. */ - pci_read_config_dword (devbusfn, PCI_BASE_ADDRESS_0, - (unsigned int *) &dev->iobase); - dev->iobase=pci_io_to_phys (devbusfn, dev->iobase); + pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, + (unsigned int *)&dev->iobase); + dev->iobase = pci_io_to_phys(devbusfn, dev->iobase); dev->iobase &= ~0xf; - PCNET_DEBUG1 ("%s: devbusfn=0x%x iobase=0x%x: ", - dev->name, devbusfn, dev->iobase); + PCNET_DEBUG1("%s: devbusfn=0x%x iobase=0x%x: ", + dev->name, devbusfn, dev->iobase); command = PCI_COMMAND_IO | PCI_COMMAND_MASTER; - pci_write_config_word (devbusfn, PCI_COMMAND, command); - pci_read_config_word (devbusfn, PCI_COMMAND, &status); + pci_write_config_word(devbusfn, PCI_COMMAND, command); + pci_read_config_word(devbusfn, PCI_COMMAND, &status); if ((status & command) != command) { - printf ("%s: Couldn't enable IO access or Bus Mastering\n", dev->name); - free (dev); + printf("%s: Couldn't enable IO access or Bus Mastering\n", + dev->name); + free(dev); continue; } - pci_write_config_byte (devbusfn, PCI_LATENCY_TIMER, 0x40); + pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x40); /* * Probe the PCnet chip. */ - if (pcnet_probe (dev, bis, dev_nr) < 0) { - free (dev); + if (pcnet_probe(dev, bis, dev_nr) < 0) { + free(dev); continue; } @@ -207,15 +208,15 @@ int pcnet_initialize (bd_t * bis) dev->send = pcnet_send; dev->recv = pcnet_recv; - eth_register (dev); + eth_register(dev); } - udelay (10 * 1000); + udelay(10 * 1000); return dev_nr; } -static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_nr) +static int pcnet_probe(struct eth_device *dev, bd_t *bis, int dev_nr) { int chip_version; char *chipname; @@ -225,17 +226,17 @@ static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_nr) #endif /* Reset the PCnet controller */ - pcnet_reset (dev); + pcnet_reset(dev); /* Check if register access is working */ - if (pcnet_read_csr (dev, 0) != 4 || !pcnet_check (dev)) { - printf ("%s: CSR register access check failed\n", dev->name); + if (pcnet_read_csr(dev, 0) != 4 || !pcnet_check(dev)) { + printf("%s: CSR register access check failed\n", dev->name); return -1; } /* Identify the chip */ chip_version = - pcnet_read_csr (dev, 88) | (pcnet_read_csr (dev, 89) << 16); + pcnet_read_csr(dev, 88) | (pcnet_read_csr(dev, 89) << 16); if ((chip_version & 0xfff) != 0x003) return -1; chip_version = (chip_version >> 12) & 0xffff; @@ -254,12 +255,12 @@ static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_nr) break; #endif default: - printf ("%s: PCnet version %#x not supported\n", - dev->name, chip_version); + printf("%s: PCnet version %#x not supported\n", + dev->name, chip_version); return -1; } - PCNET_DEBUG1 ("AMD %s\n", chipname); + PCNET_DEBUG1("AMD %s\n", chipname); #ifdef PCNET_HAS_PROM /* @@ -270,7 +271,7 @@ static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_nr) for (i = 0; i < 3; i++) { unsigned int val; - val = pcnet_read_csr (dev, i + 12) & 0x0ffff; + val = pcnet_read_csr(dev, i + 12) & 0x0ffff; /* There may be endianness issues here. */ dev->enetaddr[2 * i] = val & 0x0ff; dev->enetaddr[2 * i + 1] = (val >> 8) & 0x0ff; @@ -280,35 +281,40 @@ static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_nr) return 0; } -static int pcnet_init (struct eth_device *dev, bd_t * bis) +static int pcnet_init(struct eth_device *dev, bd_t *bis) { int i, val; u32 addr; - PCNET_DEBUG1 ("%s: pcnet_init...\n", dev->name); + PCNET_DEBUG1("%s: pcnet_init...\n", dev->name); /* Switch pcnet to 32bit mode */ - pcnet_write_bcr (dev, 20, 2); - -#ifdef CONFIG_PN62 - /* Setup LED registers */ - val = pcnet_read_bcr (dev, 2) | 0x1000; - pcnet_write_bcr (dev, 2, val); /* enable LEDPE */ - pcnet_write_bcr (dev, 4, 0x5080); /* 100MBit */ - pcnet_write_bcr (dev, 5, 0x40c0); /* LNKSE */ - pcnet_write_bcr (dev, 6, 0x4090); /* TX Activity */ - pcnet_write_bcr (dev, 7, 0x4084); /* RX Activity */ -#endif + pcnet_write_bcr(dev, 20, 2); /* Set/reset autoselect bit */ - val = pcnet_read_bcr (dev, 2) & ~2; + val = pcnet_read_bcr(dev, 2) & ~2; val |= 2; - pcnet_write_bcr (dev, 2, val); + pcnet_write_bcr(dev, 2, val); /* Enable auto negotiate, setup, disable fd */ - val = pcnet_read_bcr (dev, 32) & ~0x98; + val = pcnet_read_bcr(dev, 32) & ~0x98; val |= 0x20; - pcnet_write_bcr (dev, 32, val); + pcnet_write_bcr(dev, 32, val); + + /* + * Enable NOUFLO on supported controllers, with the transmit + * start point set to the full packet. This will cause entire + * packets to be buffered by the ethernet controller before + * transmission, eliminating underflows which are common on + * slower devices. Controllers which do not support NOUFLO will + * simply be left with a larger transmit FIFO threshold. + */ + val = pcnet_read_bcr(dev, 18); + val |= 1 << 11; + pcnet_write_bcr(dev, 18, val); + val = pcnet_read_csr(dev, 80); + val |= 0x3 << 10; + pcnet_write_csr(dev, 80, val); /* * We only maintain one structure because the drivers will never @@ -316,12 +322,12 @@ static int pcnet_init (struct eth_device *dev, bd_t * bis) * must be aligned on 16-byte boundaries. */ if (lp == NULL) { - addr = (u32) malloc (sizeof (pcnet_priv_t) + 0x10); + addr = (u32)malloc(sizeof(pcnet_priv_t) + 0x10); addr = (addr + 0xf) & ~0xf; - lp = (pcnet_priv_t *) addr; + lp = (pcnet_priv_t *)addr; } - lp->init_block.mode = cpu_to_le16 (0x0000); + lp->init_block.mode = cpu_to_le16(0x0000); lp->init_block.filter[0] = 0x00000000; lp->init_block.filter[1] = 0x00000000; @@ -330,9 +336,9 @@ static int pcnet_init (struct eth_device *dev, bd_t * bis) */ lp->cur_rx = 0; for (i = 0; i < RX_RING_SIZE; i++) { - lp->rx_ring[i].base = PCI_TO_MEM_LE (dev, lp->rx_buf[i]); - lp->rx_ring[i].buf_length = cpu_to_le16 (-PKT_BUF_SZ); - lp->rx_ring[i].status = cpu_to_le16 (0x8000); + lp->rx_ring[i].base = PCI_TO_MEM_LE(dev, lp->rx_buf[i]); + lp->rx_ring[i].buf_length = cpu_to_le16(-PKT_BUF_SZ); + lp->rx_ring[i].status = cpu_to_le16(0x8000); PCNET_DEBUG1 ("Rx%d: base=0x%x buf_length=0x%hx status=0x%hx\n", i, lp->rx_ring[i].base, lp->rx_ring[i].buf_length, @@ -352,48 +358,49 @@ static int pcnet_init (struct eth_device *dev, bd_t * bis) /* * Setup Init Block. */ - PCNET_DEBUG1 ("Init block at 0x%p: MAC", &lp->init_block); + PCNET_DEBUG1("Init block at 0x%p: MAC", &lp->init_block); for (i = 0; i < 6; i++) { lp->init_block.phys_addr[i] = dev->enetaddr[i]; - PCNET_DEBUG1 (" %02x", lp->init_block.phys_addr[i]); + PCNET_DEBUG1(" %02x", lp->init_block.phys_addr[i]); } - lp->init_block.tlen_rlen = cpu_to_le16 (TX_RING_LEN_BITS | - RX_RING_LEN_BITS); - lp->init_block.rx_ring = PCI_TO_MEM_LE (dev, lp->rx_ring); - lp->init_block.tx_ring = PCI_TO_MEM_LE (dev, lp->tx_ring); + lp->init_block.tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS | + RX_RING_LEN_BITS); + lp->init_block.rx_ring = PCI_TO_MEM_LE(dev, lp->rx_ring); + lp->init_block.tx_ring = PCI_TO_MEM_LE(dev, lp->tx_ring); + flush_dcache_range((unsigned long)lp, (unsigned long)&lp->rx_buf); - PCNET_DEBUG1 ("\ntlen_rlen=0x%x rx_ring=0x%x tx_ring=0x%x\n", - lp->init_block.tlen_rlen, - lp->init_block.rx_ring, lp->init_block.tx_ring); + PCNET_DEBUG1("\ntlen_rlen=0x%x rx_ring=0x%x tx_ring=0x%x\n", + lp->init_block.tlen_rlen, + lp->init_block.rx_ring, lp->init_block.tx_ring); /* * Tell the controller where the Init Block is located. */ - addr = PCI_TO_MEM (dev, &lp->init_block); - pcnet_write_csr (dev, 1, addr & 0xffff); - pcnet_write_csr (dev, 2, (addr >> 16) & 0xffff); + addr = PCI_TO_MEM(dev, &lp->init_block); + pcnet_write_csr(dev, 1, addr & 0xffff); + pcnet_write_csr(dev, 2, (addr >> 16) & 0xffff); - pcnet_write_csr (dev, 4, 0x0915); - pcnet_write_csr (dev, 0, 0x0001); /* start */ + pcnet_write_csr(dev, 4, 0x0915); + pcnet_write_csr(dev, 0, 0x0001); /* start */ /* Wait for Init Done bit */ for (i = 10000; i > 0; i--) { - if (pcnet_read_csr (dev, 0) & 0x0100) + if (pcnet_read_csr(dev, 0) & 0x0100) break; - udelay (10); + udelay(10); } if (i <= 0) { - printf ("%s: TIMEOUT: controller init failed\n", dev->name); - pcnet_reset (dev); + printf("%s: TIMEOUT: controller init failed\n", dev->name); + pcnet_reset(dev); return -1; } /* * Finally start network controller operation. */ - pcnet_write_csr (dev, 0, 0x0002); + pcnet_write_csr(dev, 0, 0x0002); return 0; } @@ -403,20 +410,25 @@ static int pcnet_send(struct eth_device *dev, void *packet, int pkt_len) int i, status; struct pcnet_tx_head *entry = &lp->tx_ring[lp->cur_tx]; - PCNET_DEBUG2 ("Tx%d: %d bytes from 0x%p ", lp->cur_tx, pkt_len, - packet); + PCNET_DEBUG2("Tx%d: %d bytes from 0x%p ", lp->cur_tx, pkt_len, + packet); + + flush_dcache_range((unsigned long)packet, + (unsigned long)packet + pkt_len); /* Wait for completion by testing the OWN bit */ for (i = 1000; i > 0; i--) { - status = le16_to_cpu (entry->status); + invalidate_dcache_range((unsigned long)entry, + (unsigned long)entry + sizeof(*entry)); + status = le16_to_cpu(entry->status); if ((status & 0x8000) == 0) break; - udelay (100); - PCNET_DEBUG2 ("."); + udelay(100); + PCNET_DEBUG2("."); } if (i <= 0) { - printf ("%s: TIMEOUT: Tx%d failed (status = 0x%x)\n", - dev->name, lp->cur_tx, status); + printf("%s: TIMEOUT: Tx%d failed (status = 0x%x)\n", + dev->name, lp->cur_tx, status); pkt_len = 0; goto failure; } @@ -426,19 +438,21 @@ static int pcnet_send(struct eth_device *dev, void *packet, int pkt_len) * set the status with the "ownership" bits last. */ status = 0x8300; - entry->length = le16_to_cpu (-pkt_len); + entry->length = cpu_to_le16(-pkt_len); entry->misc = 0x00000000; - entry->base = PCI_TO_MEM_LE (dev, packet); - entry->status = le16_to_cpu (status); + entry->base = PCI_TO_MEM_LE(dev, packet); + entry->status = cpu_to_le16(status); + flush_dcache_range((unsigned long)entry, + (unsigned long)entry + sizeof(*entry)); /* Trigger an immediate send poll. */ - pcnet_write_csr (dev, 0, 0x0008); + pcnet_write_csr(dev, 0, 0x0008); failure: if (++lp->cur_tx >= TX_RING_SIZE) lp->cur_tx = 0; - PCNET_DEBUG2 ("done\n"); + PCNET_DEBUG2("done\n"); return pkt_len; } @@ -450,43 +464,49 @@ static int pcnet_recv (struct eth_device *dev) while (1) { entry = &lp->rx_ring[lp->cur_rx]; + invalidate_dcache_range((unsigned long)entry, + (unsigned long)entry + sizeof(*entry)); /* * If we own the next entry, it's a new packet. Send it up. */ - if (((status = le16_to_cpu (entry->status)) & 0x8000) != 0) { + status = le16_to_cpu(entry->status); + if ((status & 0x8000) != 0) break; - } status >>= 8; if (status != 0x03) { /* There was an error. */ - - printf ("%s: Rx%d", dev->name, lp->cur_rx); - PCNET_DEBUG1 (" (status=0x%x)", status); + printf("%s: Rx%d", dev->name, lp->cur_rx); + PCNET_DEBUG1(" (status=0x%x)", status); if (status & 0x20) - printf (" Frame"); + printf(" Frame"); if (status & 0x10) - printf (" Overflow"); + printf(" Overflow"); if (status & 0x08) - printf (" CRC"); + printf(" CRC"); if (status & 0x04) - printf (" Fifo"); - printf (" Error\n"); - entry->status &= le16_to_cpu (0x03ff); + printf(" Fifo"); + printf(" Error\n"); + entry->status &= le16_to_cpu(0x03ff); } else { - - pkt_len = - (le32_to_cpu (entry->msg_length) & 0xfff) - 4; + pkt_len = (le32_to_cpu(entry->msg_length) & 0xfff) - 4; if (pkt_len < 60) { - printf ("%s: Rx%d: invalid packet length %d\n", dev->name, lp->cur_rx, pkt_len); + printf("%s: Rx%d: invalid packet length %d\n", + dev->name, lp->cur_rx, pkt_len); } else { - NetReceive (lp->rx_buf[lp->cur_rx], pkt_len); - PCNET_DEBUG2 ("Rx%d: %d bytes from 0x%p\n", - lp->cur_rx, pkt_len, - lp->rx_buf[lp->cur_rx]); + invalidate_dcache_range( + (unsigned long)lp->rx_buf[lp->cur_rx], + (unsigned long)lp->rx_buf[lp->cur_rx] + + pkt_len); + NetReceive(lp->rx_buf[lp->cur_rx], pkt_len); + PCNET_DEBUG2("Rx%d: %d bytes from 0x%p\n", + lp->cur_rx, pkt_len, + lp->rx_buf[lp->cur_rx]); } } - entry->status |= cpu_to_le16 (0x8000); + entry->status |= cpu_to_le16(0x8000); + flush_dcache_range((unsigned long)entry, + (unsigned long)entry + sizeof(*entry)); if (++lp->cur_rx >= RX_RING_SIZE) lp->cur_rx = 0; @@ -494,22 +514,21 @@ static int pcnet_recv (struct eth_device *dev) return pkt_len; } -static void pcnet_halt (struct eth_device *dev) +static void pcnet_halt(struct eth_device *dev) { int i; - PCNET_DEBUG1 ("%s: pcnet_halt...\n", dev->name); + PCNET_DEBUG1("%s: pcnet_halt...\n", dev->name); /* Reset the PCnet controller */ - pcnet_reset (dev); + pcnet_reset(dev); /* Wait for Stop bit */ for (i = 1000; i > 0; i--) { - if (pcnet_read_csr (dev, 0) & 0x4) + if (pcnet_read_csr(dev, 0) & 0x4) break; - udelay (10); - } - if (i <= 0) { - printf ("%s: TIMEOUT: controller reset failed\n", dev->name); + udelay(10); } + if (i <= 0) + printf("%s: TIMEOUT: controller reset failed\n", dev->name); } diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c index 0f2dfd612..b20b4df98 100644 --- a/drivers/net/phy/atheros.c +++ b/drivers/net/phy/atheros.c @@ -40,7 +40,7 @@ static int ar8035_config(struct phy_device *phydev) static struct phy_driver AR8021_driver = { .name = "AR8021", .uid = 0x4dd040, - .mask = 0xfffff0, + .mask = 0x4fffff, .features = PHY_GBIT_FEATURES, .config = ar8021_config, .startup = genphy_startup, @@ -48,11 +48,11 @@ static struct phy_driver AR8021_driver = { }; static struct phy_driver AR8031_driver = { - .name = "AR8031", + .name = "AR8031/AR8033", .uid = 0x4dd074, - .mask = 0xfffff0, + .mask = 0x4fffff, .features = PHY_GBIT_FEATURES, - .config = genphy_config, + .config = ar8021_config, .startup = genphy_startup, .shutdown = genphy_shutdown, }; diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index a7450f832..5d7e3be52 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -100,6 +100,19 @@ int ksz9021_phy_extended_read(struct phy_device *phydev, int regnum) return phy_read(phydev, MDIO_DEVAD_NONE, MII_KSZ9021_EXTENDED_DATAR); } + +static int ksz9021_phy_extread(struct phy_device *phydev, int addr, int devaddr, + int regnum) +{ + return ksz9021_phy_extended_read(phydev, regnum); +} + +static int ksz9021_phy_extwrite(struct phy_device *phydev, int addr, + int devaddr, int regnum, u16 val) +{ + return ksz9021_phy_extended_write(phydev, regnum, val); +} + /* Micrel ksz9021 */ static int ksz9021_config(struct phy_device *phydev) { @@ -131,6 +144,8 @@ static struct phy_driver ksz9021_driver = { .config = &ksz9021_config, .startup = &ksz90xx_startup, .shutdown = &genphy_shutdown, + .writeext = &ksz9021_phy_extwrite, + .readext = &ksz9021_phy_extread, }; #endif @@ -171,14 +186,31 @@ int ksz9031_phy_extended_read(struct phy_device *phydev, int devaddr, return phy_read(phydev, MDIO_DEVAD_NONE, MII_KSZ9031_MMD_REG_DATA); } +static int ksz9031_phy_extread(struct phy_device *phydev, int addr, int devaddr, + int regnum) +{ + return ksz9031_phy_extended_read(phydev, devaddr, regnum, + MII_KSZ9031_MOD_DATA_NO_POST_INC); +}; + +static int ksz9031_phy_extwrite(struct phy_device *phydev, int addr, + int devaddr, int regnum, u16 val) +{ + return ksz9031_phy_extended_write(phydev, devaddr, regnum, + MII_KSZ9031_MOD_DATA_POST_INC_RW, val); +}; + + static struct phy_driver ksz9031_driver = { .name = "Micrel ksz9031", .uid = 0x221620, - .mask = 0xfffffe, + .mask = 0xfffff0, .features = PHY_GBIT_FEATURES, .config = &genphy_config, .startup = &ksz90xx_startup, .shutdown = &genphy_shutdown, + .writeext = &ksz9031_phy_extwrite, + .readext = &ksz9031_phy_extread, }; int phy_micrel_init(void) diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 62925bb28..c691fbbbc 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -275,13 +275,14 @@ int genphy_parse_link(struct phy_device *phydev) int mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); /* We're using autonegotiation */ - if (mii_reg & BMSR_ANEGCAPABLE) { + if (phydev->supported & SUPPORTED_Autoneg) { u32 lpa = 0; int gblpa = 0; u32 estatus = 0; /* Check for gigabit capability */ - if (mii_reg & BMSR_ERCAP) { + if (phydev->supported & (SUPPORTED_1000baseT_Full | + SUPPORTED_1000baseT_Half)) { /* We want a list of states supported by * both PHYs in the link */ diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c index ddbbc35e2..a3ace6852 100644 --- a/drivers/net/phy/realtek.c +++ b/drivers/net/phy/realtek.c @@ -102,7 +102,7 @@ static int rtl8211x_startup(struct phy_device *phydev) static struct phy_driver RTL8211B_driver = { .name = "RealTek RTL8211B", .uid = 0x1cc910, - .mask = 0xfffff0, + .mask = 0xffffff, .features = PHY_GBIT_FEATURES, .config = &rtl8211x_config, .startup = &rtl8211x_startup, @@ -113,7 +113,7 @@ static struct phy_driver RTL8211B_driver = { static struct phy_driver RTL8211E_driver = { .name = "RealTek RTL8211E", .uid = 0x1cc915, - .mask = 0xfffff0, + .mask = 0xffffff, .features = PHY_GBIT_FEATURES, .config = &rtl8211x_config, .startup = &rtl8211x_startup, @@ -124,7 +124,7 @@ static struct phy_driver RTL8211E_driver = { static struct phy_driver RTL8211DN_driver = { .name = "RealTek RTL8211DN", .uid = 0x1cc914, - .mask = 0xfffff0, + .mask = 0xffffff, .features = PHY_GBIT_FEATURES, .config = &rtl8211x_config, .startup = &rtl8211x_startup, diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c index 60ed92d20..bfd9815ab 100644 --- a/drivers/net/phy/smsc.c +++ b/drivers/net/phy/smsc.c @@ -12,6 +12,7 @@ */ #include <miiphy.h> +/* This code does not check the partner abilities. */ static int smsc_parse_status(struct phy_device *phydev) { int mii_reg; @@ -64,7 +65,7 @@ static struct phy_driver lan8710_driver = { .mask = 0xffff0, .features = PHY_BASIC_FEATURES, .config = &genphy_config_aneg, - .startup = &smsc_startup, + .startup = &genphy_startup, .shutdown = &genphy_shutdown, }; diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c index 5cf103e5a..c55597966 100644 --- a/drivers/net/phy/vitesse.c +++ b/drivers/net/phy/vitesse.c @@ -49,6 +49,15 @@ #define MIIM_VSC8574_18G_QSGMII 0x80e0 #define MIIM_VSC8574_18G_CMDSTAT 0x8000 +/* Vitesse VSC8514 control register */ +#define MIIM_VSC8514_GENERAL18 0x12 +#define MIIM_VSC8514_GENERAL19 0x13 +#define MIIM_VSC8514_GENERAL23 0x17 + +/* Vitesse VSC8514 gerenal purpose register 18 */ +#define MIIM_VSC8514_18G_QSGMII 0x80e0 +#define MIIM_VSC8514_18G_CMDSTAT 0x8000 + /* CIS8201 */ static int vitesse_config(struct phy_device *phydev) { @@ -148,7 +157,7 @@ static int vsc8601_config(struct phy_device *phydev) static int vsc8574_config(struct phy_device *phydev) { u32 val; - /* configure regiser 19G for MAC */ + /* configure register 19G for MAC */ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, PHY_EXT_PAGE_ACCESS_GENERAL); @@ -188,6 +197,53 @@ static int vsc8574_config(struct phy_device *phydev) return 0; } +static int vsc8514_config(struct phy_device *phydev) +{ + u32 val; + int timeout = 1000000; + + /* configure register to access 19G */ + phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, + PHY_EXT_PAGE_ACCESS_GENERAL); + + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL19); + if (phydev->interface == PHY_INTERFACE_MODE_QSGMII) { + /* set bit 15:14 to '01' for QSGMII mode */ + val = (val & 0x3fff) | (1 << 14); + phy_write(phydev, MDIO_DEVAD_NONE, + MIIM_VSC8514_GENERAL19, val); + /* Enable 4 ports MAC QSGMII */ + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL18, + MIIM_VSC8514_18G_QSGMII); + } else { + /*TODO Add SGMII functionality once spec sheet + * for VSC8514 defines complete functionality + */ + } + + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL18); + /* When bit 15 is cleared the command has completed */ + while ((val & MIIM_VSC8514_18G_CMDSTAT) && timeout--) + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL18); + + if (0 == timeout) { + printf("PHY 8514 config failed\n"); + return -1; + } + + phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0); + + /* configure register to access 23 */ + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL23); + /* set bits 10:8 to '000' */ + val = (val & 0xf8ff); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL23, val); + + genphy_config_aneg(phydev); + + return 0; +} + static struct phy_driver VSC8211_driver = { .name = "Vitesse VSC8211", .uid = 0xfc4b0, @@ -238,6 +294,16 @@ static struct phy_driver VSC8574_driver = { .shutdown = &genphy_shutdown, }; +static struct phy_driver VSC8514_driver = { + .name = "Vitesse VSC8514", + .uid = 0x70570, + .mask = 0xffff0, + .features = PHY_GBIT_FEATURES, + .config = &vsc8514_config, + .startup = &vitesse_startup, + .shutdown = &genphy_shutdown, +}; + static struct phy_driver VSC8601_driver = { .name = "Vitesse VSC8601", .uid = 0x70420, @@ -298,6 +364,7 @@ int phy_vitesse_init(void) phy_register(&VSC8211_driver); phy_register(&VSC8221_driver); phy_register(&VSC8574_driver); + phy_register(&VSC8514_driver); phy_register(&VSC8662_driver); phy_register(&cis8201_driver); phy_register(&cis8204_driver); diff --git a/drivers/net/rtl8139.c b/drivers/net/rtl8139.c index 4186699ff..208ce5ccc 100644 --- a/drivers/net/rtl8139.c +++ b/drivers/net/rtl8139.c @@ -188,7 +188,7 @@ static int rtl_transmit(struct eth_device *dev, void *packet, int length); static int rtl_poll(struct eth_device *dev); static void rtl_disable(struct eth_device *dev); #ifdef CONFIG_MCAST_TFTP/* This driver already accepts all b/mcast */ -static int rtl_bcast_addr (struct eth_device *dev, u8 bcast_mac, u8 set) +static int rtl_bcast_addr(struct eth_device *dev, const u8 *bcast_mac, u8 set) { return (0); } diff --git a/drivers/net/rtl8169.c b/drivers/net/rtl8169.c index 13fa9c02f..d040ab171 100644 --- a/drivers/net/rtl8169.c +++ b/drivers/net/rtl8169.c @@ -246,6 +246,8 @@ static struct { {"RTL-8169sc/8110sc", 0x18, 0xff7e1880,}, {"RTL-8168b/8111sb", 0x30, 0xff7e1880,}, {"RTL-8168b/8111sb", 0x38, 0xff7e1880,}, + {"RTL-8168d/8111d", 0x28, 0xff7e1880,}, + {"RTL-8168evl/8111evl", 0x2e, 0xff7e1880,}, {"RTL-8101e", 0x34, 0xff7e1880,}, {"RTL-8100e", 0x32, 0xff7e1880,}, }; @@ -314,6 +316,7 @@ static const unsigned int rtl8169_rx_config = static struct pci_device_id supported[] = { {PCI_VENDOR_ID_REALTEK, 0x8167}, + {PCI_VENDOR_ID_REALTEK, 0x8168}, {PCI_VENDOR_ID_REALTEK, 0x8169}, {} }; @@ -394,6 +397,50 @@ match: return 0; } +/* + * Cache maintenance functions. These are simple wrappers around the more + * general purpose flush_cache() and invalidate_dcache_range() functions. + */ + +static void rtl_inval_rx_desc(struct RxDesc *desc) +{ + unsigned long start = (unsigned long)desc & ~(ARCH_DMA_MINALIGN - 1); + unsigned long end = ALIGN(start + sizeof(*desc), ARCH_DMA_MINALIGN); + + invalidate_dcache_range(start, end); +} + +static void rtl_flush_rx_desc(struct RxDesc *desc) +{ + flush_cache((unsigned long)desc, sizeof(*desc)); +} + +static void rtl_inval_tx_desc(struct TxDesc *desc) +{ + unsigned long start = (unsigned long)desc & ~(ARCH_DMA_MINALIGN - 1); + unsigned long end = ALIGN(start + sizeof(*desc), ARCH_DMA_MINALIGN); + + invalidate_dcache_range(start, end); +} + +static void rtl_flush_tx_desc(struct TxDesc *desc) +{ + flush_cache((unsigned long)desc, sizeof(*desc)); +} + +static void rtl_inval_buffer(void *buf, size_t size) +{ + unsigned long start = (unsigned long)buf & ~(ARCH_DMA_MINALIGN - 1); + unsigned long end = ALIGN(start + size, ARCH_DMA_MINALIGN); + + invalidate_dcache_range(start, end); +} + +static void rtl_flush_buffer(void *buf, size_t size) +{ + flush_cache((unsigned long)buf, size); +} + /************************************************************************** RECV - Receive a frame ***************************************************************************/ @@ -411,14 +458,16 @@ static int rtl_recv(struct eth_device *dev) ioaddr = dev->iobase; cur_rx = tpc->cur_rx; - flush_cache((unsigned long)&tpc->RxDescArray[cur_rx], - sizeof(struct RxDesc)); + + rtl_inval_rx_desc(&tpc->RxDescArray[cur_rx]); + if ((le32_to_cpu(tpc->RxDescArray[cur_rx].status) & OWNbit) == 0) { if (!(le32_to_cpu(tpc->RxDescArray[cur_rx].status) & RxRES)) { unsigned char rxdata[RX_BUF_LEN]; length = (int) (le32_to_cpu(tpc->RxDescArray[cur_rx]. status) & 0x00001FFF) - 4; + rtl_inval_buffer(tpc->RxBufferRing[cur_rx], length); memcpy(rxdata, tpc->RxBufferRing[cur_rx], length); NetReceive(rxdata, length); @@ -430,8 +479,7 @@ static int rtl_recv(struct eth_device *dev) cpu_to_le32(OWNbit + RX_BUF_SIZE); tpc->RxDescArray[cur_rx].buf_addr = cpu_to_le32(bus_to_phys(tpc->RxBufferRing[cur_rx])); - flush_cache((unsigned long)tpc->RxBufferRing[cur_rx], - RX_BUF_SIZE); + rtl_flush_rx_desc(&tpc->RxDescArray[cur_rx]); } else { puts("Error Rx"); } @@ -473,7 +521,7 @@ static int rtl_send(struct eth_device *dev, void *packet, int length) /* point to the current txb incase multiple tx_rings are used */ ptxb = tpc->Tx_skbuff[entry * MAX_ETH_FRAME_SIZE]; memcpy(ptxb, (char *)packet, (int)length); - flush_cache((unsigned long)ptxb, length); + rtl_flush_buffer(ptxb, length); while (len < ETH_ZLEN) ptxb[len++] = '\0'; @@ -489,20 +537,20 @@ static int rtl_send(struct eth_device *dev, void *packet, int length) cpu_to_le32((OWNbit | EORbit | FSbit | LSbit) | ((len > ETH_ZLEN) ? len : ETH_ZLEN)); } + rtl_flush_tx_desc(&tpc->TxDescArray[entry]); RTL_W8(TxPoll, 0x40); /* set polling bit */ tpc->cur_tx++; to = currticks() + TX_TIMEOUT; do { - flush_cache((unsigned long)&tpc->TxDescArray[entry], - sizeof(struct TxDesc)); + rtl_inval_tx_desc(&tpc->TxDescArray[entry]); } while ((le32_to_cpu(tpc->TxDescArray[entry].status) & OWNbit) && (currticks() < to)); /* wait */ if (currticks() >= to) { #ifdef DEBUG_RTL8169_TX - puts ("tx timeout/error\n"); - printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); + puts("tx timeout/error\n"); + printf("%s elapsed time : %lu\n", __func__, currticks()-stime); #endif ret = 0; } else { @@ -604,7 +652,7 @@ static void rtl8169_hw_start(struct eth_device *dev) RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000); #ifdef DEBUG_RTL8169 - printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); + printf("%s elapsed time : %lu\n", __func__, currticks()-stime); #endif } @@ -638,11 +686,11 @@ static void rtl8169_init_ring(struct eth_device *dev) tpc->RxBufferRing[i] = &rxb[i * RX_BUF_SIZE]; tpc->RxDescArray[i].buf_addr = cpu_to_le32(bus_to_phys(tpc->RxBufferRing[i])); - flush_cache((unsigned long)tpc->RxBufferRing[i], RX_BUF_SIZE); + rtl_flush_rx_desc(&tpc->RxDescArray[i]); } #ifdef DEBUG_RTL8169 - printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); + printf("%s elapsed time : %lu\n", __func__, currticks()-stime); #endif } @@ -683,7 +731,7 @@ static int rtl_reset(struct eth_device *dev, bd_t *bis) txb[5] = dev->enetaddr[5]; #ifdef DEBUG_RTL8169 - printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); + printf("%s elapsed time : %lu\n", __func__, currticks()-stime); #endif return 0; } @@ -869,11 +917,25 @@ int rtl8169_initialize(bd_t *bis) int idx=0; while(1){ + unsigned int region; + u16 device; + /* Find RTL8169 */ if ((devno = pci_find_devices(supported, idx++)) < 0) break; - pci_read_config_dword(devno, PCI_BASE_ADDRESS_1, &iobase); + pci_read_config_word(devno, PCI_DEVICE_ID, &device); + switch (device) { + case 0x8168: + region = 2; + break; + + default: + region = 1; + break; + } + + pci_read_config_dword(devno, PCI_BASE_ADDRESS_0 + (region * 4), &iobase); iobase &= ~0xf; debug ("rtl8169: REALTEK RTL8169 @0x%x\n", iobase); diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c index d5a83e0bf..5e132f2b5 100644 --- a/drivers/net/sh_eth.c +++ b/drivers/net/sh_eth.c @@ -4,6 +4,7 @@ * Copyright (C) 2008, 2011 Renesas Solutions Corp. * Copyright (c) 2008, 2011 Nobuhiro Iwamatsu * Copyright (c) 2007 Carlos Munoz <carlos@kenati.com> + * Copyright (C) 2013 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0+ */ @@ -25,13 +26,31 @@ #ifndef CONFIG_SH_ETHER_PHY_ADDR # error "Please define CONFIG_SH_ETHER_PHY_ADDR" #endif -#ifdef CONFIG_SH_ETHER_CACHE_WRITEBACK -#define flush_cache_wback(addr, len) \ - dcache_wback_range((u32)addr, (u32)(addr + len - 1)) + +#if defined(CONFIG_SH_ETHER_CACHE_WRITEBACK) && !defined(CONFIG_SYS_DCACHE_OFF) +#define flush_cache_wback(addr, len) \ + flush_dcache_range((u32)addr, (u32)(addr + len - 1)) #else #define flush_cache_wback(...) #endif +#if defined(CONFIG_SH_ETHER_CACHE_INVALIDATE) && defined(CONFIG_ARM) +#define invalidate_cache(addr, len) \ + { \ + u32 line_size = CONFIG_SH_ETHER_ALIGNE_SIZE; \ + u32 start, end; \ + \ + start = (u32)addr; \ + end = start + len; \ + start &= ~(line_size - 1); \ + end = ((end + line_size - 1) & ~(line_size - 1)); \ + \ + invalidate_dcache_range(start, end); \ + } +#else +#define invalidate_cache(...) +#endif + #define TIMEOUT_CNT 1000 int sh_eth_send(struct eth_device *dev, void *packet, int len) @@ -69,8 +88,11 @@ int sh_eth_send(struct eth_device *dev, void *packet, int len) /* Wait until packet is transmitted */ timeout = TIMEOUT_CNT; - while (port_info->tx_desc_cur->td0 & TD_TACT && timeout--) + do { + invalidate_cache(port_info->tx_desc_cur, + sizeof(struct tx_desc_s)); udelay(100); + } while (port_info->tx_desc_cur->td0 & TD_TACT && timeout--); if (timeout < 0) { printf(SHETHER_NAME ": transmit timeout\n"); @@ -94,12 +116,14 @@ int sh_eth_recv(struct eth_device *dev) uchar *packet; /* Check if the rx descriptor is ready */ + invalidate_cache(port_info->rx_desc_cur, sizeof(struct rx_desc_s)); if (!(port_info->rx_desc_cur->rd0 & RD_RACT)) { /* Check for errors */ if (!(port_info->rx_desc_cur->rd0 & RD_RFE)) { len = port_info->rx_desc_cur->rd1 & 0xffff; packet = (uchar *) ADDR_TO_P2(port_info->rx_desc_cur->rd2); + invalidate_cache(packet, len); NetReceive(packet, len); } @@ -108,7 +132,6 @@ int sh_eth_recv(struct eth_device *dev) port_info->rx_desc_cur->rd0 = RD_RACT | RD_RDLE; else port_info->rx_desc_cur->rd0 = RD_RACT; - /* Point to the next descriptor */ port_info->rx_desc_cur++; if (port_info->rx_desc_cur >= @@ -237,15 +260,17 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth) * Allocate rx data buffers. They must be 32 bytes aligned and in * P2 area */ - port_info->rx_buf_malloc = malloc(NUM_RX_DESC * MAX_BUF_SIZE + 31); + port_info->rx_buf_malloc = malloc( + NUM_RX_DESC * MAX_BUF_SIZE + RX_BUF_ALIGNE_SIZE - 1); if (!port_info->rx_buf_malloc) { printf(SHETHER_NAME ": malloc failed\n"); ret = -ENOMEM; goto err_buf_malloc; } - tmp_addr = (u32)(((int)port_info->rx_buf_malloc + (32 - 1)) & - ~(32 - 1)); + tmp_addr = (u32)(((int)port_info->rx_buf_malloc + + (RX_BUF_ALIGNE_SIZE - 1)) & + ~(RX_BUF_ALIGNE_SIZE - 1)); port_info->rx_buf_base = (u8 *)ADDR_TO_P2(tmp_addr); /* Initialize all descriptors */ @@ -351,8 +376,9 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd) struct phy_device *phy; /* Configure e-dmac registers */ - sh_eth_write(eth, (sh_eth_read(eth, EDMR) & ~EMDR_DESC_R) | EDMR_EL, - EDMR); + sh_eth_write(eth, (sh_eth_read(eth, EDMR) & ~EMDR_DESC_R) | + (EMDR_DESC | EDMR_EL), EDMR); + sh_eth_write(eth, 0, EESIPR); sh_eth_write(eth, 0, TRSCER); sh_eth_write(eth, 0, TFTR); @@ -384,6 +410,8 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd) #if defined(CONFIG_CPU_SH7734) || defined(CONFIG_R8A7740) sh_eth_write(eth, CONFIG_SH_ETHER_SH7734_MII, RMII_MII); +#elif defined(CONFIG_R8A7790) || defined(CONFIG_R8A7791) + sh_eth_write(eth, sh_eth_read(eth, RMIIMR) | 0x1, RMIIMR); #endif /* Configure phy */ ret = sh_eth_phy_config(eth); @@ -407,7 +435,8 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd) sh_eth_write(eth, GECMR_100B, GECMR); #elif defined(CONFIG_CPU_SH7757) || defined(CONFIG_CPU_SH7752) sh_eth_write(eth, 1, RTRATE); -#elif defined(CONFIG_CPU_SH7724) +#elif defined(CONFIG_CPU_SH7724) || defined(CONFIG_R8A7790) || \ + defined(CONFIG_R8A7791) val = ECMR_RTM; #endif } else if (phy->speed == 10) { diff --git a/drivers/net/sh_eth.h b/drivers/net/sh_eth.h index 9ad800e42..8aa71098c 100644 --- a/drivers/net/sh_eth.h +++ b/drivers/net/sh_eth.h @@ -31,6 +31,11 @@ #define ADDR_TO_P2(addr) (addr) #endif /* defined(CONFIG_SH) */ +/* base padding size is 16 */ +#ifndef CONFIG_SH_ETHER_ALIGNE_SIZE +#define CONFIG_SH_ETHER_ALIGNE_SIZE 16 +#endif + /* Number of supported ports */ #define MAX_PORT_NUM 2 @@ -45,15 +50,16 @@ /* The size of the tx descriptor is determined by how much padding is used. 4, 20, or 52 bytes of padding can be used */ -#define TX_DESC_PADDING 4 -#define TX_DESC_SIZE (12 + TX_DESC_PADDING) +#define TX_DESC_PADDING (CONFIG_SH_ETHER_ALIGNE_SIZE - 12) +/* same as CONFIG_SH_ETHER_ALIGNE_SIZE */ +#define TX_DESC_SIZE (12 + TX_DESC_PADDING) /* Tx descriptor. We always use 3 bytes of padding */ struct tx_desc_s { volatile u32 td0; u32 td1; u32 td2; /* Buffer start */ - u32 padding; + u8 padding[TX_DESC_PADDING]; /* aligned cache line size */ }; /* There is no limitation in the number of rx descriptors */ @@ -61,15 +67,18 @@ struct tx_desc_s { /* The size of the rx descriptor is determined by how much padding is used. 4, 20, or 52 bytes of padding can be used */ -#define RX_DESC_PADDING 4 +#define RX_DESC_PADDING (CONFIG_SH_ETHER_ALIGNE_SIZE - 12) +/* same as CONFIG_SH_ETHER_ALIGNE_SIZE */ #define RX_DESC_SIZE (12 + RX_DESC_PADDING) +/* aligned cache line size */ +#define RX_BUF_ALIGNE_SIZE (CONFIG_SH_ETHER_ALIGNE_SIZE > 32 ? 64 : 32) /* Rx descriptor. We always use 4 bytes of padding */ struct rx_desc_s { volatile u32 rd0; volatile u32 rd1; u32 rd2; /* Buffer start */ - u32 padding; + u8 padding[TX_DESC_PADDING]; /* aligned cache line size */ }; struct sh_eth_info { @@ -157,6 +166,7 @@ enum { TLFRCR, CERCR, CEECR, + RMIIMR, /* R8A7790 */ MAFCR, RTRATE, CSMR, @@ -263,6 +273,7 @@ static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = { [RMCR] = 0x0058, [TFUCR] = 0x0064, [RFOCR] = 0x0068, + [RMIIMR] = 0x006C, [FCFTR] = 0x0070, [RPADIR] = 0x0078, [TRIMD] = 0x007c, @@ -290,6 +301,9 @@ static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = { #elif defined(CONFIG_R8A7740) #define SH_ETH_TYPE_GETHER #define BASE_IO_ADDR 0xE9A00000 +#elif defined(CONFIG_R8A7790) || defined(CONFIG_R8A7791) +#define SH_ETH_TYPE_ETHER +#define BASE_IO_ADDR 0xEE700200 #endif /* @@ -320,6 +334,14 @@ enum DMAC_M_BIT { #endif }; +#if CONFIG_SH_ETHER_ALIGNE_SIZE == 64 +# define EMDR_DESC EDMR_DL1 +#elif CONFIG_SH_ETHER_ALIGNE_SIZE == 32 +# define EMDR_DESC EDMR_DL0 +#elif CONFIG_SH_ETHER_ALIGNE_SIZE == 16 /* Default */ +# define EMDR_DESC 0 +#endif + /* RFLR */ #define RFLR_RFL_MIN 0x05EE /* Recv Frame length 1518 byte */ @@ -485,6 +507,8 @@ enum FELIC_MODE_BIT { ECMR_PRM = 0x00000001, #ifdef CONFIG_CPU_SH7724 ECMR_RTM = 0x00000010, +#elif defined(CONFIG_R8A7790) || defined(CONFIG_R8A7791) + ECMR_RTM = 0x00000004, #endif }; diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index f5e314b9e..e9138f033 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -5,7 +5,7 @@ * terms of the GNU Public License, Version 2, incorporated * herein by reference. * - * Copyright 2004-2011 Freescale Semiconductor, Inc. + * Copyright 2004-2011, 2013 Freescale Semiconductor, Inc. * (C) Copyright 2003, Motorola, Inc. * author Andy Fleming * @@ -25,21 +25,13 @@ DECLARE_GLOBAL_DATA_PTR; #define TX_BUF_CNT 2 -static uint rxIdx; /* index of the current RX buffer */ -static uint txIdx; /* index of the current TX buffer */ - -typedef volatile struct rtxbd { - txbd8_t txbd[TX_BUF_CNT]; - rxbd8_t rxbd[PKTBUFSRX]; -} RTXBD; - -#define MAXCONTROLLERS (8) - -static struct tsec_private *privlist[MAXCONTROLLERS]; -static int num_tsecs = 0; +static uint rx_idx; /* index of the current RX buffer */ +static uint tx_idx; /* index of the current TX buffer */ #ifdef __GNUC__ -static RTXBD rtx __attribute__ ((aligned(8))); +static struct txbd8 __iomem txbd[TX_BUF_CNT] __aligned(8); +static struct rxbd8 __iomem rxbd[PKTBUFSRX] __aligned(8); + #else #error "rtx must be 64-bit aligned" #endif @@ -57,7 +49,7 @@ static struct tsec_info_struct tsec_info[] = { #endif #ifdef CONFIG_MPC85XX_FEC { - .regs = (tsec_t *)(TSEC_BASE_ADDR + 0x2000), + .regs = TSEC_GET_REGS(2, 0x2000), .devname = CONFIG_MPC85XX_FEC_NAME, .phyaddr = FEC_PHY_ADDR, .flags = FEC_FLAGS, @@ -113,32 +105,31 @@ static void tsec_configure_serdes(struct tsec_private *priv) * result. * 2) Use the 8 most significant bits as a hash into a 256-entry * table. The table is controlled through 8 32-bit registers: - * gaddr0-7. gaddr0's MSB is entry 0, and gaddr7's LSB is - * gaddr7. This means that the 3 most significant bits in the + * gaddr0-7. gaddr0's MSB is entry 0, and gaddr7's LSB is entry + * 255. This means that the 3 most significant bits in the * hash index which gaddr register to use, and the 5 other bits * indicate which bit (assuming an IBM numbering scheme, which - * for PowerPC (tm) is usually the case) in the tregister holds + * for PowerPC (tm) is usually the case) in the register holds * the entry. */ static int -tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set) +tsec_mcast_addr(struct eth_device *dev, const u8 *mcast_mac, u8 set) { - struct tsec_private *priv = privlist[1]; - volatile tsec_t *regs = priv->regs; - volatile u32 *reg_array, value; - u8 result, whichbit, whichreg; + struct tsec_private *priv = (struct tsec_private *)dev->priv; + struct tsec __iomem *regs = priv->regs; + u32 result, value; + u8 whichbit, whichreg; - result = (u8)((ether_crc(MAC_ADDR_LEN,mcast_mac) >> 24) & 0xff); - whichbit = result & 0x1f; /* the 5 LSB = which bit to set */ - whichreg = result >> 5; /* the 3 MSB = which reg to set it in */ - value = (1 << (31-whichbit)); + result = ether_crc(MAC_ADDR_LEN, mcast_mac); + whichbit = (result >> 24) & 0x1f; /* the 5 LSB = which bit to set */ + whichreg = result >> 29; /* the 3 MSB = which reg to set it in */ - reg_array = &(regs->hash.gaddr0); + value = 1 << (31-whichbit); + + if (set) + setbits_be32(®s->hash.gaddr0 + whichreg, value); + else + clrbits_be32(®s->hash.gaddr0 + whichreg, value); - if (set) { - reg_array[whichreg] |= value; - } else { - reg_array[whichreg] &= ~value; - } return 0; } #endif /* Multicast TFTP ? */ @@ -147,7 +138,7 @@ tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set) * those we don't care about (unless zero is bad, in which case, * choose a more appropriate value) */ -static void init_registers(tsec_t *regs) +static void init_registers(struct tsec __iomem *regs) { /* Clear IEVENT */ out_be32(®s->ievent, IEVENT_INIT_CLEAR); @@ -175,7 +166,7 @@ static void init_registers(tsec_t *regs) out_be32(®s->rctrl, 0x00000000); /* Init RMON mib registers */ - memset((void *)&(regs->rmon), 0, sizeof(rmon_mib_t)); + memset((void *)®s->rmon, 0, sizeof(regs->rmon)); out_be32(®s->rmon.cam1, 0xffffffff); out_be32(®s->rmon.cam2, 0xffffffff); @@ -194,7 +185,7 @@ static void init_registers(tsec_t *regs) */ static void adjust_link(struct tsec_private *priv, struct phy_device *phydev) { - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; u32 ecntrl, maccfg2; if (!phydev->link) { @@ -248,7 +239,7 @@ static void adjust_link(struct tsec_private *priv, struct phy_device *phydev) void redundant_init(struct eth_device *dev) { struct tsec_private *priv = dev->priv; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; uint t, count = 0; int fail = 1; static const u8 pkt[] = { @@ -281,23 +272,26 @@ void redundant_init(struct eth_device *dev) clrbits_be32(®s->dmactrl, DMACTRL_GRS | DMACTRL_GTS); do { + uint16_t status; tsec_send(dev, (void *)pkt, sizeof(pkt)); /* Wait for buffer to be received */ - for (t = 0; rtx.rxbd[rxIdx].status & RXBD_EMPTY; t++) { + for (t = 0; in_be16(&rxbd[rx_idx].status) & RXBD_EMPTY; t++) { if (t >= 10 * TOUT_LOOP) { printf("%s: tsec: rx error\n", dev->name); break; } } - if (!memcmp(pkt, (void *)NetRxPackets[rxIdx], sizeof(pkt))) + if (!memcmp(pkt, (void *)NetRxPackets[rx_idx], sizeof(pkt))) fail = 0; - rtx.rxbd[rxIdx].length = 0; - rtx.rxbd[rxIdx].status = - RXBD_EMPTY | (((rxIdx + 1) == PKTBUFSRX) ? RXBD_WRAP : 0); - rxIdx = (rxIdx + 1) % PKTBUFSRX; + out_be16(&rxbd[rx_idx].length, 0); + status = RXBD_EMPTY; + if ((rx_idx + 1) == PKTBUFSRX) + status |= RXBD_WRAP; + out_be16(&rxbd[rx_idx].status, status); + rx_idx = (rx_idx + 1) % PKTBUFSRX; if (in_be32(®s->ievent) & IEVENT_BSY) { out_be32(®s->ievent, IEVENT_BSY); @@ -325,36 +319,39 @@ void redundant_init(struct eth_device *dev) */ static void startup_tsec(struct eth_device *dev) { - int i; struct tsec_private *priv = (struct tsec_private *)dev->priv; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; + uint16_t status; + int i; /* reset the indices to zero */ - rxIdx = 0; - txIdx = 0; + rx_idx = 0; + tx_idx = 0; #ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129 uint svr; #endif /* Point to the buffer descriptors */ - out_be32(®s->tbase, (unsigned int)(&rtx.txbd[txIdx])); - out_be32(®s->rbase, (unsigned int)(&rtx.rxbd[rxIdx])); + out_be32(®s->tbase, (u32)&txbd[0]); + out_be32(®s->rbase, (u32)&rxbd[0]); /* Initialize the Rx Buffer descriptors */ for (i = 0; i < PKTBUFSRX; i++) { - rtx.rxbd[i].status = RXBD_EMPTY; - rtx.rxbd[i].length = 0; - rtx.rxbd[i].bufPtr = (uint) NetRxPackets[i]; + out_be16(&rxbd[i].status, RXBD_EMPTY); + out_be16(&rxbd[i].length, 0); + out_be32(&rxbd[i].bufptr, (u32)NetRxPackets[i]); } - rtx.rxbd[PKTBUFSRX - 1].status |= RXBD_WRAP; + status = in_be16(&rxbd[PKTBUFSRX - 1].status); + out_be16(&rxbd[PKTBUFSRX - 1].status, status | RXBD_WRAP); /* Initialize the TX Buffer Descriptors */ for (i = 0; i < TX_BUF_CNT; i++) { - rtx.txbd[i].status = 0; - rtx.txbd[i].length = 0; - rtx.txbd[i].bufPtr = 0; + out_be16(&txbd[i].status, 0); + out_be16(&txbd[i].length, 0); + out_be32(&txbd[i].bufptr, 0); } - rtx.txbd[TX_BUF_CNT - 1].status |= TXBD_WRAP; + status = in_be16(&txbd[TX_BUF_CNT - 1].status); + out_be16(&txbd[TX_BUF_CNT - 1].status, status | TXBD_WRAP); #ifdef CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129 svr = get_svr(); @@ -378,66 +375,67 @@ static void startup_tsec(struct eth_device *dev) */ static int tsec_send(struct eth_device *dev, void *packet, int length) { - int i; - int result = 0; struct tsec_private *priv = (struct tsec_private *)dev->priv; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; + uint16_t status; + int result = 0; + int i; /* Find an empty buffer descriptor */ - for (i = 0; rtx.txbd[txIdx].status & TXBD_READY; i++) { + for (i = 0; in_be16(&txbd[tx_idx].status) & TXBD_READY; i++) { if (i >= TOUT_LOOP) { debug("%s: tsec: tx buffers full\n", dev->name); return result; } } - rtx.txbd[txIdx].bufPtr = (uint) packet; - rtx.txbd[txIdx].length = length; - rtx.txbd[txIdx].status |= - (TXBD_READY | TXBD_LAST | TXBD_CRC | TXBD_INTERRUPT); + out_be32(&txbd[tx_idx].bufptr, (u32)packet); + out_be16(&txbd[tx_idx].length, length); + status = in_be16(&txbd[tx_idx].status); + out_be16(&txbd[tx_idx].status, status | + (TXBD_READY | TXBD_LAST | TXBD_CRC | TXBD_INTERRUPT)); /* Tell the DMA to go */ out_be32(®s->tstat, TSTAT_CLEAR_THALT); /* Wait for buffer to be transmitted */ - for (i = 0; rtx.txbd[txIdx].status & TXBD_READY; i++) { + for (i = 0; in_be16(&txbd[tx_idx].status) & TXBD_READY; i++) { if (i >= TOUT_LOOP) { debug("%s: tsec: tx error\n", dev->name); return result; } } - txIdx = (txIdx + 1) % TX_BUF_CNT; - result = rtx.txbd[txIdx].status & TXBD_STATS; + tx_idx = (tx_idx + 1) % TX_BUF_CNT; + result = in_be16(&txbd[tx_idx].status) & TXBD_STATS; return result; } static int tsec_recv(struct eth_device *dev) { - int length; struct tsec_private *priv = (struct tsec_private *)dev->priv; - tsec_t *regs = priv->regs; - - while (!(rtx.rxbd[rxIdx].status & RXBD_EMPTY)) { + struct tsec __iomem *regs = priv->regs; - length = rtx.rxbd[rxIdx].length; + while (!(in_be16(&rxbd[rx_idx].status) & RXBD_EMPTY)) { + int length = in_be16(&rxbd[rx_idx].length); + uint16_t status = in_be16(&rxbd[rx_idx].status); /* Send the packet up if there were no errors */ - if (!(rtx.rxbd[rxIdx].status & RXBD_STATS)) { - NetReceive(NetRxPackets[rxIdx], length - 4); - } else { - printf("Got error %x\n", - (rtx.rxbd[rxIdx].status & RXBD_STATS)); - } + if (!(status & RXBD_STATS)) + NetReceive(NetRxPackets[rx_idx], length - 4); + else + printf("Got error %x\n", (status & RXBD_STATS)); - rtx.rxbd[rxIdx].length = 0; + out_be16(&rxbd[rx_idx].length, 0); + status = RXBD_EMPTY; /* Set the wrap bit if this is the last element in the list */ - rtx.rxbd[rxIdx].status = - RXBD_EMPTY | (((rxIdx + 1) == PKTBUFSRX) ? RXBD_WRAP : 0); + if ((rx_idx + 1) == PKTBUFSRX) + status |= RXBD_WRAP; + out_be16(&rxbd[rx_idx].status, status); - rxIdx = (rxIdx + 1) % PKTBUFSRX; + rx_idx = (rx_idx + 1) % PKTBUFSRX; } if (in_be32(®s->ievent) & IEVENT_BSY) { @@ -453,7 +451,7 @@ static int tsec_recv(struct eth_device *dev) static void tsec_halt(struct eth_device *dev) { struct tsec_private *priv = (struct tsec_private *)dev->priv; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; clrbits_be32(®s->dmactrl, DMACTRL_GRS | DMACTRL_GTS); setbits_be32(®s->dmactrl, DMACTRL_GRS | DMACTRL_GTS); @@ -475,11 +473,9 @@ static void tsec_halt(struct eth_device *dev) */ static int tsec_init(struct eth_device *dev, bd_t * bd) { - uint tempval; - char tmpbuf[MAC_ADDR_LEN]; - int i; struct tsec_private *priv = (struct tsec_private *)dev->priv; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; + u32 tempval; int ret; /* Make sure the controller is stopped */ @@ -492,16 +488,16 @@ static int tsec_init(struct eth_device *dev, bd_t * bd) out_be32(®s->ecntrl, ECNTRL_INIT_SETTINGS); /* Copy the station address into the address registers. - * Backwards, because little endian MACS are dumb */ - for (i = 0; i < MAC_ADDR_LEN; i++) - tmpbuf[MAC_ADDR_LEN - 1 - i] = dev->enetaddr[i]; - - tempval = (tmpbuf[0] << 24) | (tmpbuf[1] << 16) | (tmpbuf[2] << 8) | - tmpbuf[3]; + * For a station address of 0x12345678ABCD in transmission + * order (BE), MACnADDR1 is set to 0xCDAB7856 and + * MACnADDR2 is set to 0x34120000. + */ + tempval = (dev->enetaddr[5] << 24) | (dev->enetaddr[4] << 16) | + (dev->enetaddr[3] << 8) | dev->enetaddr[2]; out_be32(®s->macstnaddr1, tempval); - tempval = *((uint *) (tmpbuf + 4)); + tempval = (dev->enetaddr[1] << 24) | (dev->enetaddr[0] << 16); out_be32(®s->macstnaddr2, tempval); @@ -527,7 +523,7 @@ static int tsec_init(struct eth_device *dev, bd_t * bd) static phy_interface_t tsec_get_interface(struct tsec_private *priv) { - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; u32 ecntrl; ecntrl = in_be32(®s->ecntrl); @@ -576,7 +572,7 @@ static int init_phy(struct eth_device *dev) { struct tsec_private *priv = (struct tsec_private *)dev->priv; struct phy_device *phydev; - tsec_t *regs = priv->regs; + struct tsec __iomem *regs = priv->regs; u32 supported = (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Half | @@ -626,7 +622,6 @@ static int tsec_initialize(bd_t *bis, struct tsec_info_struct *tsec_info) if (NULL == priv) return 0; - privlist[num_tsecs++] = priv; priv->regs = tsec_info->regs; priv->phyregs_sgmii = tsec_info->miiregs_sgmii; @@ -684,7 +679,7 @@ int tsec_standard_init(bd_t *bis) { struct fsl_pq_mdio_info info; - info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + info.regs = TSEC_GET_MDIO_REGS_BASE(1); info.name = DEFAULT_MII_NAME; fsl_pq_mdio_init(bis, &info); diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c index 236a75311..6a017a810 100644 --- a/drivers/net/zynq_gem.c +++ b/drivers/net/zynq_gem.c @@ -43,11 +43,6 @@ #define ZYNQ_GEM_TXBUF_WRAP_MASK 0x40000000 #define ZYNQ_GEM_TXBUF_LAST_MASK 0x00008000 /* Last buffer */ -#define ZYNQ_GEM_TXSR_HRESPNOK_MASK 0x00000100 /* Transmit hresp not OK */ -#define ZYNQ_GEM_TXSR_URUN_MASK 0x00000040 /* Transmit underrun */ -/* Transmit buffs exhausted mid frame */ -#define ZYNQ_GEM_TXSR_BUFEXH_MASK 0x00000010 - #define ZYNQ_GEM_NWCTRL_TXEN_MASK 0x00000008 /* Enable transmit */ #define ZYNQ_GEM_NWCTRL_RXEN_MASK 0x00000004 /* Enable receive */ #define ZYNQ_GEM_NWCTRL_MDEN_MASK 0x00000010 /* Enable MDIO port */ @@ -90,6 +85,11 @@ */ #define PHY_DETECT_MASK 0x1808 +/* TX BD status masks */ +#define ZYNQ_GEM_TXBUF_FRMLEN_MASK 0x000007ff +#define ZYNQ_GEM_TXBUF_EXHAUSTED 0x08000000 +#define ZYNQ_GEM_TXBUF_UNDERRUN 0x10000000 + /* Device registers */ struct zynq_gem_regs { u32 nwctrl; /* Network Control reg */ @@ -123,12 +123,18 @@ struct emac_bd { }; #define RX_BUF 3 +/* Page table entries are set to 1MB, or multiples of 1MB + * (not < 1MB). driver uses less bd's so use 1MB bdspace. + */ +#define BD_SPACE 0x100000 +/* BD separation space */ +#define BD_SEPRN_SPACE 64 /* Initialized, rxbd_current, rx_first_buf must be 0 after init */ struct zynq_gem_priv { - struct emac_bd tx_bd; - struct emac_bd rx_bd[RX_BUF]; - char rxbuffers[RX_BUF * PKTSIZE_ALIGN]; + struct emac_bd *tx_bd; + struct emac_bd *rx_bd; + char *rxbuffers; u32 rxbd_current; u32 rx_first_buf; int phyaddr; @@ -299,20 +305,18 @@ static int zynq_gem_init(struct eth_device *dev, bd_t * bis) readl(®s->stat[i]); /* Setup RxBD space */ - memset(&(priv->rx_bd), 0, sizeof(priv->rx_bd)); - /* Create the RxBD ring */ - memset(&(priv->rxbuffers), 0, sizeof(priv->rxbuffers)); + memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd)); for (i = 0; i < RX_BUF; i++) { priv->rx_bd[i].status = 0xF0000000; priv->rx_bd[i].addr = - (u32)((char *)&(priv->rxbuffers) + + ((u32)(priv->rxbuffers) + (i * PKTSIZE_ALIGN)); } /* WRAP bit to last BD */ priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK; /* Write RxBDs to IP */ - writel((u32)&(priv->rx_bd), ®s->rxqbase); + writel((u32)priv->rx_bd, ®s->rxqbase); /* Setup for DMA Configuration register */ writel(ZYNQ_GEM_DMACR_INIT, ®s->dmacr); @@ -368,32 +372,35 @@ static int zynq_gem_init(struct eth_device *dev, bd_t * bis) static int zynq_gem_send(struct eth_device *dev, void *ptr, int len) { - u32 status; + u32 addr, size; struct zynq_gem_priv *priv = dev->priv; struct zynq_gem_regs *regs = (struct zynq_gem_regs *)dev->iobase; - const u32 mask = ZYNQ_GEM_TXSR_HRESPNOK_MASK | \ - ZYNQ_GEM_TXSR_URUN_MASK | ZYNQ_GEM_TXSR_BUFEXH_MASK; /* setup BD */ - writel((u32)&(priv->tx_bd), ®s->txqbase); + writel((u32)priv->tx_bd, ®s->txqbase); /* Setup Tx BD */ - memset((void *)&(priv->tx_bd), 0, sizeof(struct emac_bd)); + memset(priv->tx_bd, 0, sizeof(struct emac_bd)); + + priv->tx_bd->addr = (u32)ptr; + priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) | + ZYNQ_GEM_TXBUF_LAST_MASK; - priv->tx_bd.addr = (u32)ptr; - priv->tx_bd.status = len | ZYNQ_GEM_TXBUF_LAST_MASK; + addr = (u32) ptr; + addr &= ~(ARCH_DMA_MINALIGN - 1); + size = roundup(len, ARCH_DMA_MINALIGN); + flush_dcache_range(addr, addr + size); + barrier(); /* Start transmit */ setbits_le32(®s->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK); - /* Read the stat register to know if the packet has been transmitted */ - status = readl(®s->txsr); - if (status & mask) - printf("Something has gone wrong here!? Status is 0x%x.\n", - status); + /* Read TX BD status */ + if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_UNDERRUN) + printf("TX underrun\n"); + if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED) + printf("TX buffers exhausted in mid frame\n"); - /* Clear Tx status register before leaving . */ - writel(status, ®s->txsr); return 0; } @@ -416,8 +423,12 @@ static int zynq_gem_recv(struct eth_device *dev) frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK; if (frame_len) { - NetReceive((u8 *) (current_bd->addr & - ZYNQ_GEM_RXBUF_ADD_MASK), frame_len); + u32 addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK; + addr &= ~(ARCH_DMA_MINALIGN - 1); + u32 size = roundup(frame_len, ARCH_DMA_MINALIGN); + invalidate_dcache_range(addr, addr + size); + + NetReceive((u8 *)addr, frame_len); if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) priv->rx_first_buf = priv->rxbd_current; @@ -471,6 +482,7 @@ int zynq_gem_initialize(bd_t *bis, int base_addr, int phy_addr, u32 emio) { struct eth_device *dev; struct zynq_gem_priv *priv; + void *bd_space; dev = calloc(1, sizeof(*dev)); if (dev == NULL) @@ -483,6 +495,18 @@ int zynq_gem_initialize(bd_t *bis, int base_addr, int phy_addr, u32 emio) } priv = dev->priv; + /* Align rxbuffers to ARCH_DMA_MINALIGN */ + priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN); + memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN); + + /* Align bd_space to 1MB */ + bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE); + mmu_set_region_dcache_behaviour((u32)bd_space, BD_SPACE, DCACHE_OFF); + + /* Initialize the bd spaces for tx and rx bd's */ + priv->tx_bd = (struct emac_bd *)bd_space; + priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE); + priv->phyaddr = phy_addr; priv->emio = emio; diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index 99d51a6a9..6182a5904 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_FSL_PCI_INIT) += fsl_pci_init.o obj-$(CONFIG_PCI) += pci.o pci_auto.o obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o +obj-$(CONFIG_PCI_MSC01) += pci_msc01.o obj-$(CONFIG_FTPCI100) += pci_ftpci100.o obj-$(CONFIG_IXP_PCI) += pci_ixp.o obj-$(CONFIG_SH4_PCI) += pci_sh4.o diff --git a/drivers/pci/pci_msc01.c b/drivers/pci/pci_msc01.c new file mode 100644 index 000000000..284ffa09b --- /dev/null +++ b/drivers/pci/pci_msc01.c @@ -0,0 +1,125 @@ +/* + * Copyright (C) 2013 Imagination Technologies + * Author: Paul Burton <paul.burton@imgtec.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <msc01.h> +#include <pci.h> +#include <pci_msc01.h> +#include <asm/io.h> + +#define PCI_ACCESS_READ 0 +#define PCI_ACCESS_WRITE 1 + +struct msc01_pci_controller { + struct pci_controller hose; + void *base; +}; + +static inline struct msc01_pci_controller * +hose_to_msc01(struct pci_controller *hose) +{ + return container_of(hose, struct msc01_pci_controller, hose); +} + +static int msc01_config_access(struct msc01_pci_controller *msc01, + unsigned char access_type, pci_dev_t bdf, + int where, u32 *data) +{ + const u32 aborts = MSC01_PCI_INTSTAT_MA_MSK | MSC01_PCI_INTSTAT_TA_MSK; + void *intstat = msc01->base + MSC01_PCI_INTSTAT_OFS; + void *cfgdata = msc01->base + MSC01_PCI_CFGDATA_OFS; + unsigned int bus = PCI_BUS(bdf); + unsigned int dev = PCI_DEV(bdf); + unsigned int devfn = PCI_DEV(bdf) << 3 | PCI_FUNC(bdf); + + /* clear abort status */ + __raw_writel(aborts, intstat); + + /* setup address */ + __raw_writel((bus << MSC01_PCI_CFGADDR_BNUM_SHF) | + (dev << MSC01_PCI_CFGADDR_DNUM_SHF) | + (devfn << MSC01_PCI_CFGADDR_FNUM_SHF) | + ((where / 4) << MSC01_PCI_CFGADDR_RNUM_SHF), + msc01->base + MSC01_PCI_CFGADDR_OFS); + + /* perform access */ + if (access_type == PCI_ACCESS_WRITE) + __raw_writel(*data, cfgdata); + else + *data = __raw_readl(cfgdata); + + /* check for aborts */ + if (__raw_readl(intstat) & aborts) { + /* clear abort status */ + __raw_writel(aborts, intstat); + return -1; + } + + return 0; +} + +static int msc01_read_config_dword(struct pci_controller *hose, pci_dev_t dev, + int where, u32 *value) +{ + struct msc01_pci_controller *msc01 = hose_to_msc01(hose); + + *value = 0xffffffff; + return msc01_config_access(msc01, PCI_ACCESS_READ, dev, where, value); +} + +static int msc01_write_config_dword(struct pci_controller *hose, pci_dev_t dev, + int where, u32 value) +{ + struct msc01_pci_controller *gt = hose_to_msc01(hose); + u32 data = value; + + return msc01_config_access(gt, PCI_ACCESS_WRITE, dev, where, &data); +} + +void msc01_pci_init(void *base, unsigned long sys_bus, unsigned long sys_phys, + unsigned long sys_size, unsigned long mem_bus, + unsigned long mem_phys, unsigned long mem_size, + unsigned long io_bus, unsigned long io_phys, + unsigned long io_size) +{ + static struct msc01_pci_controller global_msc01; + struct msc01_pci_controller *msc01; + struct pci_controller *hose; + + msc01 = &global_msc01; + msc01->base = base; + + hose = &msc01->hose; + + hose->first_busno = 0; + hose->last_busno = 0; + + /* System memory space */ + pci_set_region(&hose->regions[0], sys_bus, sys_phys, sys_size, + PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); + + /* PCI memory space */ + pci_set_region(&hose->regions[1], mem_bus, mem_phys, mem_size, + PCI_REGION_MEM); + + /* PCI I/O space */ + pci_set_region(&hose->regions[2], io_bus, io_phys, io_size, + PCI_REGION_IO); + + hose->region_count = 3; + + pci_set_ops(hose, + pci_hose_read_config_byte_via_dword, + pci_hose_read_config_word_via_dword, + msc01_read_config_dword, + pci_hose_write_config_byte_via_dword, + pci_hose_write_config_word_via_dword, + msc01_write_config_dword); + + pci_register_hose(hose); + hose->last_busno = pci_hose_scan(hose); +} diff --git a/drivers/power/twl6030.c b/drivers/power/twl6030.c index 0858b60e0..a1c6663a2 100644 --- a/drivers/power/twl6030.c +++ b/drivers/power/twl6030.c @@ -9,6 +9,26 @@ #include <twl6030.h> +static struct twl6030_data *twl; + +static struct twl6030_data twl6030_info = { + .chip_type = chip_TWL6030, + .adc_rbase = GPCH0_LSB, + .adc_ctrl = CTRL_P2, + .adc_enable = CTRL_P2_SP2, + .vbat_mult = TWL6030_VBAT_MULT, + .vbat_shift = TWL6030_VBAT_SHIFT, +}; + +static struct twl6030_data twl6032_info = { + .chip_type = chip_TWL6032, + .adc_rbase = TWL6032_GPCH0_LSB, + .adc_ctrl = TWL6032_CTRL_P1, + .adc_enable = CTRL_P1_SP1, + .vbat_mult = TWL6032_VBAT_MULT, + .vbat_shift = TWL6032_VBAT_SHIFT, +}; + static int twl6030_gpadc_read_channel(u8 channel_no) { u8 lsb = 0; @@ -16,12 +36,12 @@ static int twl6030_gpadc_read_channel(u8 channel_no) int ret = 0; ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, - GPCH0_LSB + channel_no * 2, &lsb); + twl->adc_rbase + channel_no * 2, &lsb); if (ret) return ret; ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, - GPCH0_MSB + channel_no * 2, &msb); + twl->adc_rbase + 1 + channel_no * 2, &msb); if (ret) return ret; @@ -33,7 +53,8 @@ static int twl6030_gpadc_sw2_trigger(void) u8 val; int ret = 0; - ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, CTRL_P2, CTRL_P2_SP2); + ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, + twl->adc_ctrl, twl->adc_enable); if (ret) return ret; @@ -41,7 +62,8 @@ static int twl6030_gpadc_sw2_trigger(void) val = CTRL_P2_BUSY; while (!((val & CTRL_P2_EOCP2) && (!(val & CTRL_P2_BUSY)))) { - ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, CTRL_P2, &val); + ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, + twl->adc_ctrl, &val); if (ret) return ret; udelay(1000); @@ -102,6 +124,18 @@ int twl6030_get_battery_voltage(void) { int battery_volt = 0; int ret = 0; + u8 vbatch; + + if (twl->chip_type == chip_TWL6030) { + vbatch = TWL6030_GPADC_VBAT_CHNL; + } else { + ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, + TWL6032_GPSELECT_ISB, + TWL6032_GPADC_VBAT_CHNL); + if (ret) + return ret; + vbatch = 0; + } /* Start GPADC SW conversion */ ret = twl6030_gpadc_sw2_trigger(); @@ -111,12 +145,12 @@ int twl6030_get_battery_voltage(void) } /* measure Vbat voltage */ - battery_volt = twl6030_gpadc_read_channel(7); + battery_volt = twl6030_gpadc_read_channel(vbatch); if (battery_volt < 0) { printf("Failed to read battery voltage\n"); return ret; } - battery_volt = (battery_volt * 25 * 1000) >> (10 + 2); + battery_volt = (battery_volt * twl->vbat_mult) >> twl->vbat_shift; printf("Battery Voltage: %d mV\n", battery_volt); return battery_volt; @@ -124,12 +158,35 @@ int twl6030_get_battery_voltage(void) void twl6030_init_battery_charging(void) { - u8 stat1 = 0; + u8 val = 0; int battery_volt = 0; int ret = 0; + ret = twl6030_i2c_read_u8(TWL6030_CHIP_USB, USB_PRODUCT_ID_LSB, &val); + if (ret) { + puts("twl6030_init_battery_charging(): could not determine chip!\n"); + return; + } + if (val == 0x30) { + twl = &twl6030_info; + } else if (val == 0x32) { + twl = &twl6032_info; + } else { + puts("twl6030_init_battery_charging(): unsupported chip type\n"); + return; + } + /* Enable VBAT measurement */ - twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC1, VBAT_MEAS); + if (twl->chip_type == chip_TWL6030) { + twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC1, VBAT_MEAS); + twl6030_i2c_write_u8(TWL6030_CHIP_ADC, + TWL6030_GPADC_CTRL, + GPADC_CTRL_SCALER_DIV4); + } else { + twl6030_i2c_write_u8(TWL6030_CHIP_ADC, + TWL6032_GPADC_CTRL2, + GPADC_CTRL2_CH18_SCALER_EN); + } /* Enable GPADC module */ ret = twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, TOGGLE1, FGS | GPADCS); @@ -146,10 +203,10 @@ void twl6030_init_battery_charging(void) printf("Main battery voltage too low!\n"); /* Check for the presence of USB charger */ - twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, CONTROLLER_STAT1, &stat1); + twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, CONTROLLER_STAT1, &val); /* check for battery presence indirectly via Fuel gauge */ - if ((stat1 & VBUS_DET) && (battery_volt < 3300)) + if ((val & VBUS_DET) && (battery_volt < 3300)) twl6030_start_usb_charging(); return; diff --git a/drivers/qe/Makefile b/drivers/qe/Makefile index b8c15f8e1..7f1bd0692 100644 --- a/drivers/qe/Makefile +++ b/drivers/qe/Makefile @@ -4,5 +4,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(and $(CONFIG_QE),$(CONFIG_OF_LIBFDT)) += fdt.o -obj-$(CONFIG_QE) += qe.o uccf.o uec.o uec_phy.o +obj-y := qe.o uccf.o uec.o uec_phy.o +obj-$(CONFIG_OF_LIBFDT) += fdt.o diff --git a/drivers/rtc/mc146818.c b/drivers/rtc/mc146818.c index 5f9d35959..f7cf1064f 100644 --- a/drivers/rtc/mc146818.c +++ b/drivers/rtc/mc146818.c @@ -15,7 +15,7 @@ #include <command.h> #include <rtc.h> -#ifdef __I386__ +#if defined(__I386__) || defined(CONFIG_MALTA) #include <asm/io.h> #define in8(p) inb(p) #define out8(p, v) outb(v, p) diff --git a/drivers/serial/serial_zynq.c b/drivers/serial/serial_zynq.c index 050b9c062..ff28f3c80 100644 --- a/drivers/serial/serial_zynq.c +++ b/drivers/serial/serial_zynq.c @@ -21,10 +21,6 @@ #define ZYNQ_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */ -/* Some clock/baud constants */ -#define ZYNQ_UART_BDIV 15 /* Default/reset BDIV value */ -#define ZYNQ_UART_BASECLK 3125000L /* master / (bdiv + 1) */ - struct uart_zynq { u32 control; /* Control Register [8:0] */ u32 mode; /* Mode Register [10:0] */ diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 27902fe39..ed4ecd754 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_MXC_SPI) += mxc_spi.o obj-$(CONFIG_MXS_SPI) += mxs_spi.o obj-$(CONFIG_OC_TINY_SPI) += oc_tiny_spi.o obj-$(CONFIG_OMAP3_SPI) += omap3_spi.o +obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o obj-$(CONFIG_SOFT_SPI) += soft_spi.o obj-$(CONFIG_SH_SPI) += sh_spi.o obj-$(CONFIG_FSL_ESPI) += fsl_espi.o diff --git a/drivers/spi/bfin_spi.c b/drivers/spi/bfin_spi.c index bb88f3008..aa89d89a3 100644 --- a/drivers/spi/bfin_spi.c +++ b/drivers/spi/bfin_spi.c @@ -162,21 +162,22 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, if (!spi_cs_is_valid(bus, cs)) return NULL; - if (bus >= ARRAY_SIZE(pins) || pins[bus] == NULL) { - debug("%s: invalid bus %u\n", __func__, bus); - return NULL; - } switch (bus) { #ifdef SPI0_CTL - case 0: mmr_base = SPI0_CTL; break; + case 0: + mmr_base = SPI0_CTL; break; #endif #ifdef SPI1_CTL - case 1: mmr_base = SPI1_CTL; break; + case 1: + mmr_base = SPI1_CTL; break; #endif #ifdef SPI2_CTL - case 2: mmr_base = SPI2_CTL; break; + case 2: + mmr_base = SPI2_CTL; break; #endif - default: return NULL; + default: + debug("%s: invalid bus %u\n", __func__, bus); + return NULL; } bss = spi_alloc_slave(struct bfin_spi_slave, bus, cs); diff --git a/drivers/spi/bfin_spi6xx.c b/drivers/spi/bfin_spi6xx.c index c25c4a9ae..07b833d3a 100644 --- a/drivers/spi/bfin_spi6xx.c +++ b/drivers/spi/bfin_spi6xx.c @@ -154,10 +154,6 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, if (!spi_cs_is_valid(bus, cs)) return NULL; - if (bus >= ARRAY_SIZE(pins) || pins[bus] == NULL) { - debug("%s: invalid bus %u\n", __func__, bus); - return NULL; - } switch (bus) { #ifdef SPI0_REGBASE case 0: @@ -175,6 +171,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, break; #endif default: + debug("%s: invalid bus %u\n", __func__, bus); return NULL; } diff --git a/drivers/spi/exynos_spi.c b/drivers/spi/exynos_spi.c index 699c57eb6..4d5def2d3 100644 --- a/drivers/spi/exynos_spi.c +++ b/drivers/spi/exynos_spi.c @@ -529,18 +529,18 @@ static int process_nodes(const void *blob, int node_list[], int count) * @param node SPI peripheral node to use * @return 0 if ok, -1 on error */ -struct spi_slave *spi_setup_slave_fdt(const void *blob, int node, - unsigned int cs, unsigned int max_hz, unsigned int mode) +struct spi_slave *spi_setup_slave_fdt(const void *blob, int slave_node, + int spi_node) { struct spi_bus *bus; unsigned int i; for (i = 0, bus = spi_bus; i < bus_count; i++, bus++) { - if (bus->node == node) - return spi_setup_slave(i, cs, max_hz, mode); + if (bus->node == spi_node) + return spi_base_setup_slave_fdt(blob, i, slave_node); } - debug("%s: Failed to find bus node %d\n", __func__, node); + debug("%s: Failed to find bus node %d\n", __func__, spi_node); return NULL; } diff --git a/drivers/spi/omap3_spi.c b/drivers/spi/omap3_spi.c index e80be8eaa..a3ad05647 100644 --- a/drivers/spi/omap3_spi.c +++ b/drivers/spi/omap3_spi.c @@ -20,8 +20,7 @@ #include <asm/io.h> #include "omap3_spi.h" -#define WORD_LEN 8 -#define SPI_WAIT_TIMEOUT 3000000; +#define SPI_WAIT_TIMEOUT 3000000 static void spi_reset(struct omap3_spi_slave *ds) { @@ -185,7 +184,7 @@ int spi_claim_bus(struct spi_slave *slave) /* wordlength */ conf &= ~OMAP3_MCSPI_CHCONF_WL_MASK; - conf |= (WORD_LEN - 1) << 7; + conf |= (ds->slave.wordlen - 1) << 7; /* set chipselect polarity; manage with FORCE */ if (!(ds->mode & SPI_CS_HIGH)) @@ -223,7 +222,7 @@ void spi_release_bus(struct spi_slave *slave) spi_reset(ds); } -int omap3_spi_write(struct spi_slave *slave, unsigned int len, const u8 *txp, +int omap3_spi_write(struct spi_slave *slave, unsigned int len, const void *txp, unsigned long flags) { struct omap3_spi_slave *ds = to_omap3_spi(slave); @@ -234,7 +233,8 @@ int omap3_spi_write(struct spi_slave *slave, unsigned int len, const u8 *txp, /* Enable the channel */ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN); - chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK; + chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); + chconf |= (ds->slave.wordlen - 1) << 7; chconf |= OMAP3_MCSPI_CHCONF_TRM_TX_ONLY; chconf |= OMAP3_MCSPI_CHCONF_FORCE; omap3_spi_write_chconf(ds,chconf); @@ -250,7 +250,13 @@ int omap3_spi_write(struct spi_slave *slave, unsigned int len, const u8 *txp, } } /* Write the data */ - writel(txp[i], &ds->regs->channel[ds->slave.cs].tx); + unsigned int *tx = &ds->regs->channel[ds->slave.cs].tx; + if (ds->slave.wordlen > 16) + writel(((u32 *)txp)[i], tx); + else if (ds->slave.wordlen > 8) + writel(((u16 *)txp)[i], tx); + else + writel(((u8 *)txp)[i], tx); } /* wait to finish of transfer */ @@ -268,7 +274,7 @@ int omap3_spi_write(struct spi_slave *slave, unsigned int len, const u8 *txp, return 0; } -int omap3_spi_read(struct spi_slave *slave, unsigned int len, u8 *rxp, +int omap3_spi_read(struct spi_slave *slave, unsigned int len, void *rxp, unsigned long flags) { struct omap3_spi_slave *ds = to_omap3_spi(slave); @@ -279,7 +285,8 @@ int omap3_spi_read(struct spi_slave *slave, unsigned int len, u8 *rxp, /* Enable the channel */ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN); - chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK; + chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); + chconf |= (ds->slave.wordlen - 1) << 7; chconf |= OMAP3_MCSPI_CHCONF_TRM_RX_ONLY; chconf |= OMAP3_MCSPI_CHCONF_FORCE; omap3_spi_write_chconf(ds,chconf); @@ -302,7 +309,13 @@ int omap3_spi_read(struct spi_slave *slave, unsigned int len, u8 *rxp, omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS); /* Read the data */ - rxp[i] = readl(&ds->regs->channel[ds->slave.cs].rx); + unsigned int *rx = &ds->regs->channel[ds->slave.cs].rx; + if (ds->slave.wordlen > 16) + ((u32 *)rxp)[i] = readl(rx); + else if (ds->slave.wordlen > 8) + ((u16 *)rxp)[i] = (u16)readl(rx); + else + ((u8 *)rxp)[i] = (u8)readl(rx); } if (flags & SPI_XFER_END) { @@ -314,8 +327,8 @@ int omap3_spi_read(struct spi_slave *slave, unsigned int len, u8 *rxp, } /*McSPI Transmit Receive Mode*/ -int omap3_spi_txrx(struct spi_slave *slave, - unsigned int len, const u8 *txp, u8 *rxp, unsigned long flags) +int omap3_spi_txrx(struct spi_slave *slave, unsigned int len, + const void *txp, void *rxp, unsigned long flags) { struct omap3_spi_slave *ds = to_omap3_spi(slave); int timeout = SPI_WAIT_TIMEOUT; @@ -327,7 +340,8 @@ int omap3_spi_txrx(struct spi_slave *slave, omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN); /*set TRANSMIT-RECEIVE Mode*/ - chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK; + chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); + chconf |= (ds->slave.wordlen - 1) << 7; chconf |= OMAP3_MCSPI_CHCONF_FORCE; omap3_spi_write_chconf(ds,chconf); @@ -344,7 +358,13 @@ int omap3_spi_txrx(struct spi_slave *slave, } } /* Write the data */ - writel(txp[i], &ds->regs->channel[ds->slave.cs].tx); + unsigned int *tx = &ds->regs->channel[ds->slave.cs].tx; + if (ds->slave.wordlen > 16) + writel(((u32 *)txp)[i], tx); + else if (ds->slave.wordlen > 8) + writel(((u16 *)txp)[i], tx); + else + writel(((u8 *)txp)[i], tx); /*Read: wait for RX containing data (RXS == 1)*/ while (!(readl(&ds->regs->channel[ds->slave.cs].chstat) & @@ -356,7 +376,13 @@ int omap3_spi_txrx(struct spi_slave *slave, } } /* Read the data */ - rxp[i] = readl(&ds->regs->channel[ds->slave.cs].rx); + unsigned int *rx = &ds->regs->channel[ds->slave.cs].rx; + if (ds->slave.wordlen > 16) + ((u32 *)rxp)[i] = readl(rx); + else if (ds->slave.wordlen > 8) + ((u16 *)rxp)[i] = (u16)readl(rx); + else + ((u8 *)rxp)[i] = (u8)readl(rx); } /* Disable the channel */ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS); @@ -375,14 +401,17 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, { struct omap3_spi_slave *ds = to_omap3_spi(slave); unsigned int len; - const u8 *txp = dout; - u8 *rxp = din; int ret = -1; - if (bitlen % 8) + if (ds->slave.wordlen < 4 || ds->slave.wordlen > 32) { + printf("omap3_spi: invalid wordlen %d\n", ds->slave.wordlen); + return -1; + } + + if (bitlen % ds->slave.wordlen) return -1; - len = bitlen / 8; + len = bitlen / ds->slave.wordlen; if (bitlen == 0) { /* only change CS */ int chconf = readl(&ds->regs->channel[ds->slave.cs].chconf); @@ -400,11 +429,11 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, ret = 0; } else { if (dout != NULL && din != NULL) - ret = omap3_spi_txrx(slave, len, txp, rxp, flags); + ret = omap3_spi_txrx(slave, len, dout, din, flags); else if (dout != NULL) - ret = omap3_spi_write(slave, len, txp, flags); + ret = omap3_spi_write(slave, len, dout, flags); else if (din != NULL) - ret = omap3_spi_read(slave, len, rxp, flags); + ret = omap3_spi_read(slave, len, din, flags); } return ret; } diff --git a/drivers/spi/omap3_spi.h b/drivers/spi/omap3_spi.h index 01537b624..ab7cd8444 100644 --- a/drivers/spi/omap3_spi.h +++ b/drivers/spi/omap3_spi.h @@ -99,11 +99,11 @@ static inline struct omap3_spi_slave *to_omap3_spi(struct spi_slave *slave) return container_of(slave, struct omap3_spi_slave, slave); } -int omap3_spi_txrx(struct spi_slave *slave, unsigned int len, const u8 *txp, - u8 *rxp, unsigned long flags); -int omap3_spi_write(struct spi_slave *slave, unsigned int len, const u8 *txp, +int omap3_spi_txrx(struct spi_slave *slave, unsigned int len, const void *txp, + void *rxp, unsigned long flags); +int omap3_spi_write(struct spi_slave *slave, unsigned int len, const void *txp, unsigned long flags); -int omap3_spi_read(struct spi_slave *slave, unsigned int len, u8 *rxp, +int omap3_spi_read(struct spi_slave *slave, unsigned int len, void *rxp, unsigned long flags); #endif /* _OMAP3_SPI_H_ */ diff --git a/drivers/spi/sandbox_spi.c b/drivers/spi/sandbox_spi.c new file mode 100644 index 000000000..7895305a0 --- /dev/null +++ b/drivers/spi/sandbox_spi.c @@ -0,0 +1,204 @@ +/* + * Simulate a SPI port + * + * Copyright (c) 2011-2013 The Chromium OS Authors. + * See file CREDITS for list of people who contributed to this + * project. + * + * Licensed under the GPL-2 or later. + */ + +#include <common.h> +#include <malloc.h> +#include <spi.h> +#include <os.h> + +#include <asm/errno.h> +#include <asm/spi.h> +#include <asm/state.h> + +#ifndef CONFIG_SPI_IDLE_VAL +# define CONFIG_SPI_IDLE_VAL 0xFF +#endif + +struct sandbox_spi_slave { + struct spi_slave slave; + const struct sandbox_spi_emu_ops *ops; + void *priv; +}; + +#define to_sandbox_spi_slave(s) container_of(s, struct sandbox_spi_slave, slave) + +const char *sandbox_spi_parse_spec(const char *arg, unsigned long *bus, + unsigned long *cs) +{ + char *endp; + + *bus = simple_strtoul(arg, &endp, 0); + if (*endp != ':' || *bus >= CONFIG_SANDBOX_SPI_MAX_BUS) + return NULL; + + *cs = simple_strtoul(endp + 1, &endp, 0); + if (*endp != ':' || *cs >= CONFIG_SANDBOX_SPI_MAX_CS) + return NULL; + + return endp + 1; +} + +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return bus < CONFIG_SANDBOX_SPI_MAX_BUS && + cs < CONFIG_SANDBOX_SPI_MAX_CS; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + struct sandbox_spi_slave *sss = to_sandbox_spi_slave(slave); + + debug("sandbox_spi: activating CS\n"); + if (sss->ops->cs_activate) + sss->ops->cs_activate(sss->priv); +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + struct sandbox_spi_slave *sss = to_sandbox_spi_slave(slave); + + debug("sandbox_spi: deactivating CS\n"); + if (sss->ops->cs_deactivate) + sss->ops->cs_deactivate(sss->priv); +} + +void spi_init(void) +{ +} + +void spi_set_speed(struct spi_slave *slave, uint hz) +{ +} + +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int mode) +{ + struct sandbox_spi_slave *sss; + struct sandbox_state *state = state_get_current(); + const char *spec; + + if (!spi_cs_is_valid(bus, cs)) { + debug("sandbox_spi: Invalid SPI bus/cs\n"); + return NULL; + } + + sss = spi_alloc_slave(struct sandbox_spi_slave, bus, cs); + if (!sss) { + debug("sandbox_spi: Out of memory\n"); + return NULL; + } + + spec = state->spi[bus][cs].spec; + sss->ops = state->spi[bus][cs].ops; + if (!spec || !sss->ops || sss->ops->setup(&sss->priv, spec)) { + free(sss); + printf("sandbox_spi: unable to locate a slave client\n"); + return NULL; + } + + return &sss->slave; +} + +void spi_free_slave(struct spi_slave *slave) +{ + struct sandbox_spi_slave *sss = to_sandbox_spi_slave(slave); + + debug("sandbox_spi: releasing slave\n"); + + if (sss->ops->free) + sss->ops->free(sss->priv); + + free(sss); +} + +static int spi_bus_claim_cnt[CONFIG_SANDBOX_SPI_MAX_BUS]; + +int spi_claim_bus(struct spi_slave *slave) +{ + if (spi_bus_claim_cnt[slave->bus]++) { + printf("sandbox_spi: error: bus already claimed: %d!\n", + spi_bus_claim_cnt[slave->bus]); + } + + return 0; +} + +void spi_release_bus(struct spi_slave *slave) +{ + if (--spi_bus_claim_cnt[slave->bus]) { + printf("sandbox_spi: error: bus freed too often: %d!\n", + spi_bus_claim_cnt[slave->bus]); + } +} + +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, + void *din, unsigned long flags) +{ + struct sandbox_spi_slave *sss = to_sandbox_spi_slave(slave); + uint bytes = bitlen / 8, i; + int ret = 0; + u8 *tx = (void *)dout, *rx = din; + + if (bitlen == 0) + goto done; + + /* we can only do 8 bit transfers */ + if (bitlen % 8) { + printf("sandbox_spi: xfer: invalid bitlen size %u; needs to be 8bit\n", + bitlen); + flags |= SPI_XFER_END; + goto done; + } + + if (flags & SPI_XFER_BEGIN) + spi_cs_activate(slave); + + /* make sure rx/tx buffers are full so clients can assume */ + if (!tx) { + debug("sandbox_spi: xfer: auto-allocating tx scratch buffer\n"); + tx = malloc(bytes); + if (!tx) { + debug("sandbox_spi: Out of memory\n"); + return -ENOMEM; + } + } + if (!rx) { + debug("sandbox_spi: xfer: auto-allocating rx scratch buffer\n"); + rx = malloc(bytes); + if (!rx) { + debug("sandbox_spi: Out of memory\n"); + return -ENOMEM; + } + } + + debug("sandbox_spi: xfer: bytes = %u\n tx:", bytes); + for (i = 0; i < bytes; ++i) + debug(" %u:%02x", i, tx[i]); + debug("\n"); + + ret = sss->ops->xfer(sss->priv, tx, rx, bytes); + + debug("sandbox_spi: xfer: got back %i (that's %s)\n rx:", + ret, ret ? "bad" : "good"); + for (i = 0; i < bytes; ++i) + debug(" %u:%02x", i, rx[i]); + debug("\n"); + + if (tx != dout) + free(tx); + if (rx != din) + free(rx); + + done: + if (flags & SPI_XFER_END) + spi_cs_deactivate(slave); + + return ret; +} diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index ea39d1a1e..7ddea9b02 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -5,9 +5,22 @@ */ #include <common.h> +#include <fdtdec.h> #include <malloc.h> #include <spi.h> +int spi_set_wordlen(struct spi_slave *slave, unsigned int wordlen) +{ + if (wordlen == 0 || wordlen > 32) { + printf("spi: invalid wordlen %d\n", wordlen); + return -1; + } + + slave->wordlen = wordlen; + + return 0; +} + void *spi_do_alloc_slave(int offset, int size, unsigned int bus, unsigned int cs) { @@ -20,7 +33,26 @@ void *spi_do_alloc_slave(int offset, int size, unsigned int bus, slave = (struct spi_slave *)(ptr + offset); slave->bus = bus; slave->cs = cs; + slave->wordlen = SPI_DEFAULT_WORDLEN; } return ptr; } + +#ifdef CONFIG_OF_SPI +struct spi_slave *spi_base_setup_slave_fdt(const void *blob, int busnum, + int node) +{ + int cs, max_hz, mode = 0; + + cs = fdtdec_get_int(blob, node, "reg", -1); + max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", 100000); + if (fdtdec_get_bool(blob, node, "spi-cpol")) + mode |= SPI_CPOL; + if (fdtdec_get_bool(blob, node, "spi-cpha")) + mode |= SPI_CPHA; + if (fdtdec_get_bool(blob, node, "spi-cs-high")) + mode |= SPI_CS_HIGH; + return spi_setup_slave(busnum, cs, max_hz, mode); +} +#endif diff --git a/drivers/tpm/Makefile b/drivers/tpm/Makefile index 4b8cbecaf..2f2353f80 100644 --- a/drivers/tpm/Makefile +++ b/drivers/tpm/Makefile @@ -3,8 +3,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)slb9635_i2c) - # TODO: Merge tpm_tis_lpc.c with tpm.c obj-$(CONFIG_TPM_ATMEL_TWI) += tpm_atmel_twi.o obj-$(CONFIG_TPM_TIS_I2C) += tpm.o diff --git a/drivers/tpm/tis_i2c.c b/drivers/tpm/tis_i2c.c deleted file mode 100644 index 22554e145..000000000 --- a/drivers/tpm/tis_i2c.c +++ /dev/null @@ -1,185 +0,0 @@ -/* - * Copyright (c) 2012 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include <config.h> -#include <common.h> -#include <fdtdec.h> -#include <i2c.h> -#include "slb9635_i2c/tpm.h" - -DECLARE_GLOBAL_DATA_PTR; - -/* TPM configuration */ -struct tpm { - int i2c_bus; - int slave_addr; - char inited; - int old_bus; -} tpm; - - -static int tpm_select(void) -{ - int ret; - - tpm.old_bus = i2c_get_bus_num(); - if (tpm.old_bus != tpm.i2c_bus) { - ret = i2c_set_bus_num(tpm.i2c_bus); - if (ret) { - debug("%s: Fail to set i2c bus %d\n", __func__, - tpm.i2c_bus); - return -1; - } - } - return 0; -} - -static int tpm_deselect(void) -{ - int ret; - - if (tpm.old_bus != i2c_get_bus_num()) { - ret = i2c_set_bus_num(tpm.old_bus); - if (ret) { - debug("%s: Fail to restore i2c bus %d\n", - __func__, tpm.old_bus); - return -1; - } - } - tpm.old_bus = -1; - return 0; -} - -/** - * Decode TPM configuration. - * - * @param dev Returns a configuration of TPM device - * @return 0 if ok, -1 on error - */ -static int tpm_decode_config(struct tpm *dev) -{ -#ifdef CONFIG_OF_CONTROL - const void *blob = gd->fdt_blob; - int node, parent; - int i2c_bus; - - node = fdtdec_next_compatible(blob, 0, COMPAT_INFINEON_SLB9635_TPM); - if (node < 0) { - node = fdtdec_next_compatible(blob, 0, - COMPAT_INFINEON_SLB9645_TPM); - } - if (node < 0) { - debug("%s: Node not found\n", __func__); - return -1; - } - parent = fdt_parent_offset(blob, node); - if (parent < 0) { - debug("%s: Cannot find node parent\n", __func__); - return -1; - } - i2c_bus = i2c_get_bus_num_fdt(parent); - if (i2c_bus < 0) - return -1; - dev->i2c_bus = i2c_bus; - dev->slave_addr = fdtdec_get_addr(blob, node, "reg"); -#else - dev->i2c_bus = CONFIG_INFINEON_TPM_I2C_BUS; - dev->slave_addr = CONFIG_INFINEON_TPM_I2C_ADDR; -#endif - return 0; -} - -int tis_init(void) -{ - if (tpm.inited) - return 0; - - if (tpm_decode_config(&tpm)) - return -1; - - if (tpm_select()) - return -1; - - /* - * Probe TPM twice; the first probing might fail because TPM is asleep, - * and the probing can wake up TPM. - */ - if (i2c_probe(tpm.slave_addr) && i2c_probe(tpm.slave_addr)) { - debug("%s: fail to probe i2c addr 0x%x\n", __func__, - tpm.slave_addr); - return -1; - } - - tpm_deselect(); - - tpm.inited = 1; - - return 0; -} - -int tis_open(void) -{ - int rc; - - if (!tpm.inited) - return -1; - - if (tpm_select()) - return -1; - - rc = tpm_open(tpm.slave_addr); - - tpm_deselect(); - - return rc; -} - -int tis_close(void) -{ - if (!tpm.inited) - return -1; - - if (tpm_select()) - return -1; - - tpm_close(); - - tpm_deselect(); - - return 0; -} - -int tis_sendrecv(const uint8_t *sendbuf, size_t sbuf_size, - uint8_t *recvbuf, size_t *rbuf_len) -{ - int len; - uint8_t buf[4096]; - - if (!tpm.inited) - return -1; - - if (sizeof(buf) < sbuf_size) - return -1; - - memcpy(buf, sendbuf, sbuf_size); - - if (tpm_select()) - return -1; - - len = tpm_transmit(buf, sbuf_size); - - tpm_deselect(); - - if (len < 10) { - *rbuf_len = 0; - return -1; - } - - memcpy(recvbuf, buf, len); - *rbuf_len = len; - - return 0; -} diff --git a/drivers/usb/gadget/regs-otg.h b/drivers/usb/gadget/regs-otg.h index 84bfcc5a0..ac5d11213 100644 --- a/drivers/usb/gadget/regs-otg.h +++ b/drivers/usb/gadget/regs-otg.h @@ -226,6 +226,11 @@ struct s3c_usbotg_reg { #define CLK_SEL_12MHZ (0x2 << 0) #define CLK_SEL_48MHZ (0x0 << 0) +#define EXYNOS4X12_ID_PULLUP0 (0x01 << 3) +#define EXYNOS4X12_COMMON_ON_N0 (0x01 << 4) +#define EXYNOS4X12_CLK_SEL_12MHZ (0x02 << 0) +#define EXYNOS4X12_CLK_SEL_24MHZ (0x05 << 0) + /* Device Configuration Register DCFG */ #define DEV_SPEED_HIGH_SPEED_20 (0x0 << 0) #define DEV_SPEED_FULL_SPEED_20 (0x1 << 0) diff --git a/drivers/usb/gadget/s3c_udc_otg.c b/drivers/usb/gadget/s3c_udc_otg.c index 7e2020915..ba17a0426 100644 --- a/drivers/usb/gadget/s3c_udc_otg.c +++ b/drivers/usb/gadget/s3c_udc_otg.c @@ -167,8 +167,13 @@ void otg_phy_init(struct s3c_udc *dev) writel((readl(&phy->phypwr) &~(OTG_DISABLE_0 | ANALOG_PWRDOWN) &~FORCE_SUSPEND_0), &phy->phypwr); - writel((readl(&phy->phyclk) &~(ID_PULLUP0 | COMMON_ON_N0)) | - CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */ + if (s5p_cpu_id == 0x4412) + writel((readl(&phy->phyclk) & ~(EXYNOS4X12_ID_PULLUP0 | + EXYNOS4X12_COMMON_ON_N0)) | EXYNOS4X12_CLK_SEL_24MHZ, + &phy->phyclk); /* PLL 24Mhz */ + else + writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)) | + CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */ writel((readl(&phy->rstcon) &~(LINK_SW_RST | PHYLNK_SW_RST)) | PHY_SW_RST0, &phy->rstcon); diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index c4ce48708..1b215c25f 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -28,21 +28,48 @@ static struct omap_ehci *const ehci = (struct omap_ehci *)OMAP_EHCI_BASE; static int omap_uhh_reset(void) { -/* - * Soft resetting the UHH module causes instability issues on - * all OMAPs so we just avoid it. - * - * See OMAP36xx Errata - * i571: USB host EHCI may stall when entering smart-standby mode - * i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock - * - * On OMAP4/5, soft-resetting the UHH module will put it into - * Smart-Idle mode and lead to a deadlock. - * - * On OMAP3, this doesn't seem to be the case but still instabilities - * are observed on beagle (3530 ES1.0) if soft-reset is used. - * e.g. NFS root failures with Linux kernel. - */ + int timeout = 0; + u32 rev; + + rev = readl(&uhh->rev); + + /* Soft RESET */ + writel(OMAP_UHH_SYSCONFIG_SOFTRESET, &uhh->sysc); + + switch (rev) { + case OMAP_USBHS_REV1: + /* Wait for soft RESET to complete */ + while (!(readl(&uhh->syss) & 0x1)) { + if (timeout > 100) { + printf("%s: RESET timeout\n", __func__); + return -1; + } + udelay(10); + timeout++; + } + + /* Set No-Idle, No-Standby */ + writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc); + break; + + default: /* Rev. 2 onwards */ + + udelay(2); /* Need to wait before accessing SYSCONFIG back */ + + /* Wait for soft RESET to complete */ + while ((readl(&uhh->sysc) & 0x1)) { + if (timeout > 100) { + printf("%s: RESET timeout\n", __func__); + return -1; + } + udelay(10); + timeout++; + } + + writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc); + break; + } + return 0; } diff --git a/drivers/video/Makefile b/drivers/video/Makefile index fed1c9c95..a7f54698a 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_FSL_DIU_FB) += fsl_diu_fb.o videomodes.o obj-$(CONFIG_L5F31188) += l5f31188.o obj-$(CONFIG_MPC8XX_LCD) += mpc8xx_lcd.o obj-$(CONFIG_PXA_LCD) += pxa_lcd.o +obj-$(CONFIG_SCF0403_LCD) += scf0403_lcd.o obj-$(CONFIG_S6E8AX0) += s6e8ax0.o obj-$(CONFIG_S6E63D6) += s6e63d6.o obj-$(CONFIG_LD9040) += ld9040.o diff --git a/drivers/video/bcm2835.c b/drivers/video/bcm2835.c index 58a616317..1f18231ac 100644 --- a/drivers/video/bcm2835.c +++ b/drivers/video/bcm2835.c @@ -14,6 +14,8 @@ DECLARE_GLOBAL_DATA_PTR; /* Global variables that lcd.c expects to exist */ vidinfo_t panel_info; +static u32 bcm2835_pitch; + struct msg_query { struct bcm2835_mbox_hdr hdr; struct bcm2835_mbox_tag_physical_w_h physical_w_h; @@ -30,6 +32,7 @@ struct msg_setup { struct bcm2835_mbox_tag_virtual_offset virtual_offset; struct bcm2835_mbox_tag_overscan overscan; struct bcm2835_mbox_tag_allocate_buffer allocate_buffer; + struct bcm2835_mbox_tag_pitch pitch; u32 end_tag; }; @@ -80,6 +83,7 @@ void lcd_ctrl_init(void *lcdbase) msg_setup->overscan.body.req.right = 0; BCM2835_MBOX_INIT_TAG(&msg_setup->allocate_buffer, ALLOCATE_BUFFER); msg_setup->allocate_buffer.body.req.alignment = 0x100; + BCM2835_MBOX_INIT_TAG_NO_REQ(&msg_setup->pitch, GET_PITCH); ret = bcm2835_mbox_call_prop(BCM2835_MBOX_PROP_CHAN, &msg_setup->hdr); if (ret) { @@ -90,6 +94,7 @@ void lcd_ctrl_init(void *lcdbase) w = msg_setup->physical_w_h.body.resp.width; h = msg_setup->physical_w_h.body.resp.height; + bcm2835_pitch = msg_setup->pitch.body.resp.pitch; debug("bcm2835: Final resolution is %d x %d\n", w, h); @@ -103,3 +108,9 @@ void lcd_ctrl_init(void *lcdbase) void lcd_enable(void) { } + +int lcd_get_size(int *line_length) +{ + *line_length = bcm2835_pitch; + return *line_length * panel_info.vl_row; +} diff --git a/drivers/video/bus_vcxk.c b/drivers/video/bus_vcxk.c index 0138bca05..60a5cc5b7 100644 --- a/drivers/video/bus_vcxk.c +++ b/drivers/video/bus_vcxk.c @@ -20,7 +20,6 @@ vu_long *vcxk_bws_long = ((vu_long *) (CONFIG_SYS_VCXK_BASE)); #ifndef VCBITMASK #define VCBITMASK(bitno) (0x0001 << (bitno % 16)) #endif -#ifndef CONFIG_AT91_LEGACY at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE; #define VCXK_INIT_PIN(PORT, PIN, DDR, I0O1) \ do { \ @@ -37,20 +36,6 @@ at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE; #define VCXK_ACKNOWLEDGE \ (!(readl(&pio->CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT.pdsr) & \ CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN)) -#else - #define VCXK_INIT_PIN(PORT, PIN, DDR, I0O1) \ - ((AT91PS_PIO) PORT)->PIO_PER = PIN; \ - ((AT91PS_PIO) PORT)->DDR = PIN; \ - ((AT91PS_PIO) PORT)->PIO_MDDR = PIN; \ - if (!I0O1) ((AT91PS_PIO) PORT)->PIO_PPUER = PIN; - - #define VCXK_SET_PIN(PORT, PIN) ((AT91PS_PIO) PORT)->PIO_SODR = PIN; - #define VCXK_CLR_PIN(PORT, PIN) ((AT91PS_PIO) PORT)->PIO_CODR = PIN; - - #define VCXK_ACKNOWLEDGE \ - (!(((AT91PS_PIO) CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT)->\ - PIO_PDSR & CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN)) -#endif #elif defined(CONFIG_MCF52x2) #include <asm/m5282.h> #ifndef VCBITMASK diff --git a/drivers/video/scf0403_lcd.c b/drivers/video/scf0403_lcd.c new file mode 100644 index 000000000..2bc8bcae8 --- /dev/null +++ b/drivers/video/scf0403_lcd.c @@ -0,0 +1,296 @@ +/* + * scf0403.c -- support for DataImage SCF0403 LCD + * + * Copyright (c) 2013 Adapted from Linux driver: + * Copyright (c) 2012 Anders Electronics plc. All Rights Reserved. + * Copyright (c) 2012 CompuLab, Ltd + * Dmitry Lifshitz <lifshitz@compulab.co.il> + * Ilya Ledvich <ilya@compulab.co.il> + * Inspired by Alberto Panizzo <maramaopercheseimorto@gmail.com> & + * Marek Vasut work in l4f00242t03.c + * + * U-Boot port: Nikita Kiryanov <nikita@compulab.co.il> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/gpio.h> +#include <spi.h> + +struct scf0403_cmd { + u16 cmd; + u16 *params; + int count; +}; + +struct scf0403_initseq_entry { + struct scf0403_cmd cmd; + int delay_ms; +}; + +struct scf0403_priv { + struct spi_slave *spi; + unsigned int reset_gpio; + u32 rddid; + struct scf0403_initseq_entry *init_seq; + int seq_size; +}; + +struct scf0403_priv priv; + +#define SCF0403852GGU04_ID 0x000080 + +/* SCF0403526GGU20 model commands parameters */ +static u16 extcmd_params_sn20[] = {0xff, 0x98, 0x06}; +static u16 spiinttype_params_sn20[] = {0x60}; +static u16 bc_params_sn20[] = { + 0x01, 0x10, 0x61, 0x74, 0x01, 0x01, 0x1B, + 0x12, 0x71, 0x00, 0x00, 0x00, 0x01, 0x01, + 0x05, 0x00, 0xFF, 0xF2, 0x01, 0x00, 0x40, +}; +static u16 bd_params_sn20[] = {0x01, 0x23, 0x45, 0x67, 0x01, 0x23, 0x45, 0x67}; +static u16 be_params_sn20[] = { + 0x01, 0x22, 0x22, 0xBA, 0xDC, 0x26, 0x28, 0x22, 0x22, +}; +static u16 vcom_params_sn20[] = {0x74}; +static u16 vmesur_params_sn20[] = {0x7F, 0x0F, 0x00}; +static u16 powerctl_params_sn20[] = {0x03, 0x0b, 0x00}; +static u16 lvglvolt_params_sn20[] = {0x08}; +static u16 engsetting_params_sn20[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x20}; +static u16 dispfunc_params_sn20[] = {0xa0}; +static u16 dvddvolt_params_sn20[] = {0x74}; +static u16 dispinv_params_sn20[] = {0x00, 0x00, 0x00}; +static u16 panelres_params_sn20[] = {0x82}; +static u16 framerate_params_sn20[] = {0x00, 0x13, 0x13}; +static u16 timing_params_sn20[] = {0x80, 0x05, 0x40, 0x28}; +static u16 powerctl2_params_sn20[] = {0x17, 0x75, 0x79, 0x20}; +static u16 memaccess_params_sn20[] = {0x00}; +static u16 pixfmt_params_sn20[] = {0x66}; +static u16 pgamma_params_sn20[] = { + 0x00, 0x03, 0x0b, 0x0c, 0x0e, 0x08, 0xc5, 0x04, + 0x08, 0x0c, 0x13, 0x11, 0x11, 0x14, 0x0c, 0x10, +}; +static u16 ngamma_params_sn20[] = { + 0x00, 0x0d, 0x11, 0x0c, 0x0c, 0x04, 0x76, 0x03, + 0x08, 0x0b, 0x16, 0x10, 0x0d, 0x16, 0x0a, 0x00, +}; +static u16 tearing_params_sn20[] = {0x00}; + +/* SCF0403852GGU04 model commands parameters */ +static u16 memaccess_params_sn04[] = {0x08}; +static u16 pixfmt_params_sn04[] = {0x66}; +static u16 modectl_params_sn04[] = {0x01}; +static u16 dispfunc_params_sn04[] = {0x22, 0xe2, 0xFF, 0x04}; +static u16 vcom_params_sn04[] = {0x00, 0x6A}; +static u16 pgamma_params_sn04[] = { + 0x00, 0x07, 0x0d, 0x10, 0x13, 0x19, 0x0f, 0x0c, + 0x05, 0x08, 0x06, 0x13, 0x0f, 0x30, 0x20, 0x1f, +}; +static u16 ngamma_params_sn04[] = { + 0x1F, 0x20, 0x30, 0x0F, 0x13, 0x06, 0x08, 0x05, + 0x0C, 0x0F, 0x19, 0x13, 0x10, 0x0D, 0x07, 0x00, +}; +static u16 dispinv_params_sn04[] = {0x02}; + +/* Common commands */ +static struct scf0403_cmd scf0403_cmd_slpout = {0x11, NULL, 0}; +static struct scf0403_cmd scf0403_cmd_dison = {0x29, NULL, 0}; + +/* SCF0403852GGU04 init sequence */ +static struct scf0403_initseq_entry scf0403_initseq_sn04[] = { + {{0x36, memaccess_params_sn04, ARRAY_SIZE(memaccess_params_sn04)}, 0}, + {{0x3A, pixfmt_params_sn04, ARRAY_SIZE(pixfmt_params_sn04)}, 0}, + {{0xB6, dispfunc_params_sn04, ARRAY_SIZE(dispfunc_params_sn04)}, 0}, + {{0xC5, vcom_params_sn04, ARRAY_SIZE(vcom_params_sn04)}, 0}, + {{0xE0, pgamma_params_sn04, ARRAY_SIZE(pgamma_params_sn04)}, 0}, + {{0xE1, ngamma_params_sn04, ARRAY_SIZE(ngamma_params_sn04)}, 20}, + {{0xB0, modectl_params_sn04, ARRAY_SIZE(modectl_params_sn04)}, 0}, + {{0xB4, dispinv_params_sn04, ARRAY_SIZE(dispinv_params_sn04)}, 100}, +}; + +/* SCF0403526GGU20 init sequence */ +static struct scf0403_initseq_entry scf0403_initseq_sn20[] = { + {{0xff, extcmd_params_sn20, ARRAY_SIZE(extcmd_params_sn20)}, 0}, + {{0xba, spiinttype_params_sn20, ARRAY_SIZE(spiinttype_params_sn20)}, 0}, + {{0xbc, bc_params_sn20, ARRAY_SIZE(bc_params_sn20)}, 0}, + {{0xbd, bd_params_sn20, ARRAY_SIZE(bd_params_sn20)}, 0}, + {{0xbe, be_params_sn20, ARRAY_SIZE(be_params_sn20)}, 0}, + {{0xc7, vcom_params_sn20, ARRAY_SIZE(vcom_params_sn20)}, 0}, + {{0xed, vmesur_params_sn20, ARRAY_SIZE(vmesur_params_sn20)}, 0}, + {{0xc0, powerctl_params_sn20, ARRAY_SIZE(powerctl_params_sn20)}, 0}, + {{0xfc, lvglvolt_params_sn20, ARRAY_SIZE(lvglvolt_params_sn20)}, 0}, + {{0xb6, dispfunc_params_sn20, ARRAY_SIZE(dispfunc_params_sn20)}, 0}, + {{0xdf, engsetting_params_sn20, ARRAY_SIZE(engsetting_params_sn20)}, 0}, + {{0xf3, dvddvolt_params_sn20, ARRAY_SIZE(dvddvolt_params_sn20)}, 0}, + {{0xb4, dispinv_params_sn20, ARRAY_SIZE(dispinv_params_sn20)}, 0}, + {{0xf7, panelres_params_sn20, ARRAY_SIZE(panelres_params_sn20)}, 0}, + {{0xb1, framerate_params_sn20, ARRAY_SIZE(framerate_params_sn20)}, 0}, + {{0xf2, timing_params_sn20, ARRAY_SIZE(timing_params_sn20)}, 0}, + {{0xc1, powerctl2_params_sn20, ARRAY_SIZE(powerctl2_params_sn20)}, 0}, + {{0x36, memaccess_params_sn20, ARRAY_SIZE(memaccess_params_sn20)}, 0}, + {{0x3a, pixfmt_params_sn20, ARRAY_SIZE(pixfmt_params_sn20)}, 0}, + {{0xe0, pgamma_params_sn20, ARRAY_SIZE(pgamma_params_sn20)}, 0}, + {{0xe1, ngamma_params_sn20, ARRAY_SIZE(ngamma_params_sn20)}, 0}, + {{0x35, tearing_params_sn20, ARRAY_SIZE(tearing_params_sn20)}, 0}, +}; + +static void scf0403_gpio_reset(unsigned int gpio) +{ + if (!gpio_is_valid(gpio)) + return; + + gpio_set_value(gpio, 1); + mdelay(100); + gpio_set_value(gpio, 0); + mdelay(40); + gpio_set_value(gpio, 1); + mdelay(100); +} + +static int scf0403_spi_read_rddid(struct spi_slave *spi, u32 *rddid) +{ + int error = 0; + u8 ids_buf = 0x00; + u16 dummy_buf = 0x00; + u16 cmd = 0x04; + + error = spi_set_wordlen(spi, 9); + if (error) + return error; + + /* Here 9 bits required to transmit a command */ + error = spi_xfer(spi, 9, &cmd, NULL, SPI_XFER_ONCE); + if (error) + return error; + + /* + * Here 8 + 1 bits required to arrange extra clock cycle + * before the first data bit. + * According to the datasheet - first parameter is the dummy data. + */ + error = spi_xfer(spi, 9, NULL, &dummy_buf, SPI_XFER_ONCE); + if (error) + return error; + + error = spi_set_wordlen(spi, 8); + if (error) + return error; + + /* Read rest of the data */ + error = spi_xfer(spi, 8, NULL, &ids_buf, SPI_XFER_ONCE); + if (error) + return error; + + *rddid = ids_buf; + + return 0; +} + +static int scf0403_spi_transfer(struct spi_slave *spi, struct scf0403_cmd *cmd) +{ + int i, error; + u32 command = cmd->cmd; + u32 msg; + + error = spi_set_wordlen(spi, 9); + if (error) + return error; + + error = spi_xfer(spi, 9, &command, NULL, SPI_XFER_ONCE); + if (error) + return error; + + for (i = 0; i < cmd->count; i++) { + msg = (cmd->params[i] | 0x100); + error = spi_xfer(spi, 9, &msg, NULL, SPI_XFER_ONCE); + if (error) + return error; + } + + return 0; +} + +static void scf0403_lcd_init(struct scf0403_priv *priv) +{ + int i; + + /* reset LCD */ + scf0403_gpio_reset(priv->reset_gpio); + + for (i = 0; i < priv->seq_size; i++) { + if (scf0403_spi_transfer(priv->spi, &priv->init_seq[i].cmd) < 0) + puts("SPI transfer failed\n"); + + mdelay(priv->init_seq[i].delay_ms); + } +} + +static int scf0403_request_reset_gpio(unsigned gpio) +{ + int err = gpio_request(gpio, "lcd reset"); + + if (err) + return err; + + err = gpio_direction_output(gpio, 0); + if (err) + gpio_free(gpio); + + return err; +} + +int scf0403_init(int reset_gpio) +{ + int error; + + if (gpio_is_valid(reset_gpio)) { + error = scf0403_request_reset_gpio(reset_gpio); + if (error) { + printf("Failed requesting reset GPIO%d: %d\n", + reset_gpio, error); + return error; + } + } + + priv.reset_gpio = reset_gpio; + priv.spi = spi_setup_slave(3, 0, 1000000, SPI_MODE_0); + error = spi_claim_bus(priv.spi); + if (error) + goto bus_claim_fail; + + /* reset LCD */ + scf0403_gpio_reset(reset_gpio); + + error = scf0403_spi_read_rddid(priv.spi, &priv.rddid); + if (error) { + puts("IDs read failed\n"); + goto readid_fail; + } + + if (priv.rddid == SCF0403852GGU04_ID) { + priv.init_seq = scf0403_initseq_sn04; + priv.seq_size = ARRAY_SIZE(scf0403_initseq_sn04); + } else { + priv.init_seq = scf0403_initseq_sn20; + priv.seq_size = ARRAY_SIZE(scf0403_initseq_sn20); + } + + scf0403_lcd_init(&priv); + + /* Start operation */ + scf0403_spi_transfer(priv.spi, &scf0403_cmd_dison); + mdelay(100); + scf0403_spi_transfer(priv.spi, &scf0403_cmd_slpout); + spi_release_bus(priv.spi); + + return 0; + +readid_fail: + spi_release_bus(priv.spi); +bus_claim_fail: + if (gpio_is_valid(priv.reset_gpio)) + gpio_free(priv.reset_gpio); + + return error; +} |