diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/e1000.c | 42 |
1 files changed, 1 insertions, 41 deletions
diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index 94b2a41e1..2d4da4b38 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -135,7 +135,6 @@ static void e1000_set_media_type(struct e1000_hw *hw); static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); -#ifndef CONFIG_AP1000 /* remove for warnings */ static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); @@ -942,7 +941,6 @@ e1000_set_phy_mode(struct e1000_hw *hw) return E1000_SUCCESS; } -#endif /* #ifndef CONFIG_AP1000 */ /*************************************************************************** * @@ -1123,7 +1121,6 @@ static boolean_t e1000_is_second_port(struct e1000_hw *hw) static int e1000_read_mac_addr(struct eth_device *nic) { -#ifndef CONFIG_AP1000 struct e1000_hw *hw = nic->priv; uint16_t offset; uint16_t eeprom_data; @@ -1152,31 +1149,6 @@ e1000_read_mac_addr(struct eth_device *nic) memcpy (nic->enetaddr, fb_mac, NODE_ADDRESS_SIZE); } #endif -#else - /* - * The AP1000's e1000 has no eeprom; the MAC address is stored in the - * environment variables. Currently this does not support the addition - * of a PMC e1000 card, which is certainly a possibility, so this should - * be updated to properly use the env variable only for the onboard e1000 - */ - - int ii; - char *s, *e; - - DEBUGFUNC(); - - s = getenv ("ethaddr"); - if (s == NULL) { - return -E1000_ERR_EEPROM; - } else { - for(ii = 0; ii < 6; ii++) { - nic->enetaddr[ii] = s ? simple_strtoul (s, &e, 16) : 0; - if (s){ - s = (*e) ? e + 1 : e; - } - } - } -#endif return 0; } @@ -1808,7 +1780,6 @@ e1000_setup_link(struct eth_device *nic) if (e1000_check_phy_reset_block(hw)) return E1000_SUCCESS; -#ifndef CONFIG_AP1000 /* Read and store word 0x0F of the EEPROM. This word contains bits * that determine the hardware's default PAUSE (flow control) mode, * a bit that determines whether the HW defaults to enabling or @@ -1822,11 +1793,6 @@ e1000_setup_link(struct eth_device *nic) DEBUGOUT("EEPROM Read Error\n"); return -E1000_ERR_EEPROM; } -#else - /* we have to hardcode the proper value for our hardware. */ - /* this value is for the 82540EM pci card used for prototyping, and it works. */ - eeprom_data = 0xb220; -#endif if (hw->fc == e1000_fc_default) { switch (hw->mac_type) { @@ -1836,16 +1802,12 @@ e1000_setup_link(struct eth_device *nic) hw->fc = e1000_fc_full; break; default: -#ifndef CONFIG_AP1000 ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); if (ret_val) { DEBUGOUT("EEPROM Read Error\n"); return -E1000_ERR_EEPROM; } -#else - eeprom_data = 0xb220; -#endif if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) hw->fc = e1000_fc_none; else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == @@ -2109,12 +2071,10 @@ e1000_copper_link_preconfig(struct e1000_hw *hw) } DEBUGOUT("Phy ID = %x \n", hw->phy_id); -#ifndef CONFIG_AP1000 /* Set PHY to class A mode (if necessary) */ ret_val = e1000_set_phy_mode(hw); if (ret_val) return ret_val; -#endif if ((hw->mac_type == e1000_82545_rev_3) || (hw->mac_type == e1000_82546_rev_3)) { ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, @@ -5242,7 +5202,7 @@ e1000_initialize(bd_t * bis) list_add_tail(&hw->list_node, &e1000_hw_list); /* Validate the EEPROM and get chipset information */ -#if !(defined(CONFIG_AP1000) || defined(CONFIG_MVBC_1G)) +#if !defined(CONFIG_MVBC_1G) if (e1000_init_eeprom_params(hw)) { E1000_ERR(nic, "EEPROM is invalid!\n"); continue; |