diff options
Diffstat (limited to 'drivers/power')
| -rw-r--r-- | drivers/power/palmas.c | 133 |
1 files changed, 121 insertions, 12 deletions
diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c index 09c832d8b..2d275a761 100644 --- a/drivers/power/palmas.c +++ b/drivers/power/palmas.c @@ -25,28 +25,137 @@ void palmas_init_settings(void) { - return; +#ifdef CONFIG_PALMAS_SMPS7_FPWM + int err; + /* + * Set SMPS7 (1.8 V I/O supply on platforms with TWL6035/37) to + * forced PWM mode. This reduces noise (but affects efficiency). + */ + u8 val = SMPS_MODE_SLP_FPWM | SMPS_MODE_ACT_FPWM; + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS7_CTRL, val); + if (err) + printf("palmas: could not force PWM for SMPS7: err = %d\n", + err); +#endif } int palmas_mmc1_poweron_ldo(void) { u8 val = 0; - /* set LDO9 TWL6035 to 3V */ - val = 0x2b; /* (3 -.9)*28 +1 */ - - if (palmas_i2c_write_u8(0x48, LDO9_VOLTAGE, val)) { - printf("twl6035: could not set LDO9 voltage.\n"); +#if defined(CONFIG_DRA7XX) + /* + * Currently valid for the dra7xx_evm board: + * Set TPS659038 LDO1 to 3.0 V + */ + val = LDO_VOLT_3V0; + if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_VOLTAGE, val)) { + printf("tps65903x: could not set LDO1 voltage.\n"); + return 1; + } + /* TURN ON LDO1 */ + val = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; + if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_CTRL, val)) { + printf("tps65903x: could not turn on LDO1.\n"); return 1; } + return 0; +#else + /* + * We assume that this is a OMAP543X + TWL603X board: + * Set TWL6035/37 LDO9 to 3.0 V + */ + val = LDO_VOLT_3V0; + return twl603x_mmc1_set_ldo9(val); +#endif +} - /* TURN ON LDO9 */ - val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE; +/* + * On some OMAP5 + TWL603X hardware the SD card socket and LDO9_IN are + * powered by an external 3.3 V regulator, while the output of LDO9 + * supplies VDDS_SDCARD for the OMAP5 interface only. This implies that + * LDO9 could be set to 'bypass' mode when required (e.g. for 3.3 V cards). + */ +int twl603x_mmc1_set_ldo9(u8 vsel) +{ + u8 cval = 0, vval = 0; /* Off by default */ + int err; - if (palmas_i2c_write_u8(0x48, LDO9_CTRL, val)) { - printf("twl6035: could not turn on LDO9.\n"); - return 1; + if (vsel) { + /* Turn on */ + if (vsel > LDO_VOLT_3V3) { + /* Put LDO9 in bypass */ + cval = LDO9_BYP_EN | RSC_MODE_SLEEP | RSC_MODE_ACTIVE; + vval = LDO_VOLT_3V3; + } else { + cval = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; + vval = vsel & 0x3f; + } + } + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_VOLTAGE, vval); + if (err) { + printf("twl603x: could not set LDO9 %s: err = %d\n", + vsel > LDO_VOLT_3V3 ? "bypass" : "voltage", err); + return err; } + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_CTRL, cval); + if (err) + printf("twl603x: could not turn %s LDO9: err = %d\n", + cval ? "on" : "off", err); + return err; +} - return 0; +#ifdef CONFIG_PALMAS_AUDPWR +/* + * Turn audio codec power and 32 kHz clock on/off. Use for + * testing OMAP543X + TWL603X + TWL604X boards only. + */ +int twl603x_audio_power(u8 on) +{ + u8 cval = 0, vval = 0, c32k = 0; + int err; + + if (on) { + vval = SMPS_VOLT_2V1; + cval = SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO; + c32k = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; + } + /* Set SMPS9 to 2.1 V (for TWL604x), or to 0 (off) */ + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_VOLTAGE, vval); + if (err) { + printf("twl603x: could not set SMPS9 voltage: err = %d\n", + err); + return err; + } + /* Turn on or off SMPS9 */ + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_CTRL, cval); + if (err) { + printf("twl603x: could not turn SMPS9 %s: err = %d\n", + cval ? "on" : "off", err); + return err; + } + /* Output 32 kHz clock on or off */ + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, CLK32KGAUDIO_CTRL, c32k); + if (err) + printf("twl603x: could not turn CLK32KGAUDIO %s: err = %d\n", + c32k ? "on" : "off", err); + return err; +} +#endif + +/* + * Enable/disable back-up battery (or super cap) charging on TWL6035/37. + * Please use defined BB_xxx values. + */ +int twl603x_enable_bb_charge(u8 bb_fields) +{ + u8 val = bb_fields & 0x0f; + int err; + + val |= (VRTC_EN_SLP | VRTC_EN_OFF | VRTC_PWEN); + err = palmas_i2c_write_u8(TWL603X_CHIP_P1, BB_VRTC_CTRL, val); + if (err) + printf("twl603x: could not set BB_VRTC_CTRL to 0x%02x: err = %d\n", + val, err); + return err; } |