4 files changed, 177 insertions, 0 deletions
diff --git a/doc/README.sh7753evb b/doc/README.sh7753evb
new file mode 100644
index 000000000..5fe178c53
--- /dev/null
+++ b/doc/README.sh7753evb
@@ -0,0 +1,67 @@
+========================================
+Renesas SH7753 EVB board
+========================================
+
+This board specification:
+=========================
+
+The SH7753 EVB (board config name:sh7753evb) has the following device:
+
+ - SH7753 (SH-4A)
+ - DDR3-SDRAM 512MB
+ - SPI ROM 8MB
+ - Gigabit Ethernet controllers
+ - eMMC 4GB
+
+
+Configuration for This board:
+=============================
+
+You can select the configuration as follows:
+
+ - make sh7753evb_config
+
+
+This board specific command:
+============================
+
+This board has the following its specific command:
+
+ - write_mac
+
+
+1. write_mac
+
+You can write MAC address to SPI ROM.
+
+ Usage 1) Write MAC address
+
+   write_mac [GETHERC ch0] [GETHERC ch1]
+
+	For example)
+	 => write_mac 74:90:50:00:33:9e 74:90:50:00:33:9f
+		*) We have to input the command as a single line
+		   (without carriage return)
+		*) We have to reset after input the command.
+
+ Usage 2) Show current data
+
+   write_mac
+
+	For example)
+		=> write_mac
+		GETHERC ch0 = 74:90:50:00:33:9e
+		GETHERC ch1 = 74:90:50:00:33:9f
+
+
+Update SPI ROM:
+============================
+
+1. Copy u-boot image to RAM area.
+2. Probe SPI device.
+   => sf probe 0
+   SF: Detected MX25L6405D with page size 64KiB, total 8 MiB
+3. Erase SPI ROM.
+   => sf erase 0 80000
+4. Write u-boot image to SPI ROM.
+   => sf write 0x48000000 0 80000
diff --git a/doc/README.socfpga b/doc/README.socfpga
new file mode 100644
index 000000000..cfcbbfe37
--- /dev/null
+++ b/doc/README.socfpga
@@ -0,0 +1,53 @@
+
+--------------------------------------------
+SOCFPGA Documentation for U-Boot and SPL
+--------------------------------------------
+
+This README is about U-Boot and SPL support for Altera's ARM Cortex-A9MPCore
+based SOCFPGA. To know more about the hardware itself, please refer to
+www.altera.com.
+
+
+--------------------------------------------
+socfpga_dw_mmc
+--------------------------------------------
+Here are macro and detailed configuration required to enable DesignWare SDMMC
+controller support within SOCFPGA
+
+#define CONFIG_MMC
+-> To enable the SD MMC framework support
+
+#define CONFIG_SDMMC_BASE		(SOCFPGA_SDMMC_ADDRESS)
+-> The base address of CSR register for DesignWare SDMMC controller
+
+#define CONFIG_GENERIC_MMC
+-> Enable the generic MMC driver
+
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT	256
+-> Using smaller max blk cnt to avoid flooding the limited stack in OCRAM
+
+#define CONFIG_DWMMC
+-> Enable the common DesignWare SDMMC controller framework
+
+#define CONFIG_SOCFPGA_DWMMC
+-> Enable the SOCFPGA specific driver for DesignWare SDMMC controller
+
+#define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH		1024
+-> The FIFO depth for SOCFPGA DesignWare SDMMC controller
+
+#define CONFIG_SOCFPGA_DWMMC_DRVSEL	3
+-> Phase-shifted clock of sdmmc_clk for controller to drive command and data to
+the card to meet hold time requirements. SD clock is running at 50MHz and
+drvsel is set to shift 135 degrees (3 * 45 degrees). With that, the hold time
+is 135 / 360 * 20ns = 7.5ns.
+
+#define CONFIG_SOCFPGA_DWMMC_SMPSEL	0
+-> Phase-shifted clock of sdmmc_clk used to sample the command and data from
+the card
+
+#define CONFIG_SOCFPGA_DWMMC_BUS_WIDTH	4
+-> Bus width of data line which either 1, 4 or 8 and based on board routing.
+
+#define CONFIG_SOCFPGA_DWMMC_BUS_HZ	50000000
+-> The clock rate to controller. Do note the controller have a wrapper which
+divide the clock from PLL by 4.
diff --git a/doc/README.vxworks b/doc/README.vxworks
new file mode 100644
index 000000000..4cb302e7f
--- /dev/null
+++ b/doc/README.vxworks
@@ -0,0 +1,19 @@
+From VxWorks 6.9+ (not include 6.9), VxWorks starts adopting device tree as its hardware
+decription mechansim (for PowerPC and ARM), thus requiring boot interface changes.
+This section will describe the new interface.
+
+For PowerPC, the calling convention of the new VxWorks entry point conforms to the ePAPR standard,
+which is shown below (see ePAPR for more details):
+
+    void (*kernel_entry)(fdt_addr,
+              0, 0, EPAPR_MAGIC, boot_IMA, 0, 0)
+
+For ARM, the calling convention is show below:
+
+    void (*kernel_entry)(void *fdt_addr)
+
+When booting new VxWorks kernel (uImage format), the parameters passed to bootm is like below:
+
+    bootm <kernel image address> - <device tree address>
+
+The do_bootvx command still works as it was for older VxWorks kernels.
diff --git a/doc/SPI/README.sh_qspi_test b/doc/SPI/README.sh_qspi_test
new file mode 100644
index 000000000..8a33fec32
--- /dev/null
+++ b/doc/SPI/README.sh_qspi_test
@@ -0,0 +1,38 @@
+-------------------------------------------------
+   Simple steps used to test the SH-QSPI at U-Boot
+-------------------------------------------------
+
+#0, Currently, SH-QSPI is used by lager board (Renesas ARM SoC R8A7790)
+    and koelsch board (Renesas ARM SoC R8A7791). These boot from SPI ROM
+    basically. Thus, U-Boot start, SH-QSPI will is operating normally.
+
+#1, build U-Boot and load u-boot.bin
+
+  => tftpboot 40000000 u-boot.bin
+  sh_eth Waiting for PHY auto negotiation to complete.. done
+  sh_eth: 100Base/Half
+  Using sh_eth device
+  TFTP from server 192.168.169.1; our IP address is 192.168.169.79
+  Filename 'u-boot.bin'.
+  Load address: 0x40000000
+  Loading: ############
+    2.5 MiB/s
+  done
+  Bytes transferred = 175364 (2ad04 hex)
+
+#2, Commands to erase/write u-boot to flash device
+
+  Note: This method is description of the lager board. If you want to use the
+  other boards, please change the value according to each environment.
+
+  =>  sf probe 0
+  SF: Detected S25FL512S_256K with page size 512 Bytes, erase size 64 KiB, total 64 MiB
+  => sf erase 80000 40000
+  SF: 262144 bytes @ 0x80000 Erased: OK
+  => sf write 40000000 80000 175364
+  SF: 1528676 bytes @ 0x80000 Written: OK
+  =>
+
+#3, Push reset button.
+
+  If you're written correctly and driver works properly, U-Boot starts.