diff options
Diffstat (limited to 'board/sandburst/metrobox/metrobox.c')
| -rw-r--r-- | board/sandburst/metrobox/metrobox.c | 16 |
1 files changed, 8 insertions, 8 deletions
diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c index c38850d6c..c3c44593a 100644 --- a/board/sandburst/metrobox/metrobox.c +++ b/board/sandburst/metrobox/metrobox.c @@ -55,7 +55,7 @@ int board_early_init_f (void) mtsdr(sdr_pfc0, 0x00103E00); /* Setup access for LEDs, and system topology info */ - gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE; + gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE; gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS; gpio_regs->tri_state = SBCOMMON_GPIO_DBGLEDS; @@ -83,7 +83,7 @@ int board_early_init_f (void) EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | EBC_BXAP_PEN_DISABLED); - mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | + mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT); /*--------------------------------------------------------------------+ | 8KB NVRAM/RTC. Initialize bank 1 with default values. @@ -246,7 +246,7 @@ int checkboard (void) unsigned char opto_rev, opto_id; OPTO_FPGA_REGS_ST *opto_ps; - opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; opto_rev = (unsigned char)((opto_ps->revision_ul & SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) @@ -286,7 +286,7 @@ int checkboard (void) /* Fix the ack in the bme 32 */ udelay(5000); - out32(CFG_BME32_BASE + 0x0000000C, 0x00000001); + out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001); asm("eieio"); @@ -302,7 +302,7 @@ int misc_init_f (void) { /* Turn on i2c bus 1 */ puts ("I2C1: "); - i2c1_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); + i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); puts ("ready\n"); /* Turn on fans */ @@ -323,7 +323,7 @@ int misc_init_r (void) unsigned char opto_rev; OPTO_FPGA_REGS_ST *opto_ps; - opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; if(NULL != getenv("secondserial")) { puts("secondserial is set, switching to second serial port\n"); @@ -387,7 +387,7 @@ int misc_init_r (void) void ide_set_reset(int on) { OPTO_FPGA_REGS_ST *opto_ps; - opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; if (on) { /* assert RESET */ opto_ps->reset_ul &= ~SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK; @@ -412,7 +412,7 @@ void fpga_init(void) /* * Take appropriate hw bits out of reset */ - opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; + opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE; tmp = SAND_HAL_XC_XCVR_CNTL_RESET_MAC1_RESET_N_MASK | |