diff options
Diffstat (limited to 'board/prodrive/pdnb3/pdnb3.c')
| -rw-r--r-- | board/prodrive/pdnb3/pdnb3.c | 220 |
1 files changed, 0 insertions, 220 deletions
diff --git a/board/prodrive/pdnb3/pdnb3.c b/board/prodrive/pdnb3/pdnb3.c deleted file mode 100644 index fa320da2d..000000000 --- a/board/prodrive/pdnb3/pdnb3.c +++ /dev/null @@ -1,220 +0,0 @@ -/* - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <asm/arch/ixp425.h> - -DECLARE_GLOBAL_DATA_PTR; - -/* predefine these here for FPGA programming (before including fpga.c) */ -#define SET_FPGA(data) *IXP425_GPIO_GPOUTR = (data) -#define FPGA_DONE_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_DONE) -#define FPGA_INIT_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_INIT) -#define OLD_VAL old_val - -static unsigned long old_val = 0; - -/* - * include common fpga code (for prodrive boards) - */ -#include "../common/fpga.c" - -/* - * Miscelaneous platform dependent initialisations - */ -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_FPGA_RESET); - - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_SYS_RUNNING); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_SYS_RUNNING); - - /* - * Setup GPIO's for FPGA programming - */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PRG); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DATA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_INIT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DONE); - - /* - * Setup GPIO's for interrupts - */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTORE_INT); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTORE_INT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTART_INT); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTART_INT); - - /* - * Setup GPIO's for 33MHz clock output - */ - *IXP425_GPIO_GPCLKR = 0x01FF0000; - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK_33M); - - /* - * Setup other chip select's - */ - *IXP425_EXP_CS1 = CONFIG_SYS_EXP_CS1; - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: PDNB3"); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return (0); -} - -int dram_init(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - - return (0); -} - -int do_fpga_boot(unsigned char *fpgadata) -{ - unsigned char *dst; - int status; - int index; - int i; - ulong len = CONFIG_SYS_MALLOC_LEN; - - /* - * Setup GPIO's for FPGA programming - */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA); - - /* - * Save value so no readback is required upon programming - */ - old_val = *IXP425_GPIO_GPOUTR; - - /* - * First try to decompress fpga image (gzip compressed?) - */ - dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE); - if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) { - printf("Error: Image has to be gzipp'ed!\n"); - return -1; - } - - status = fpga_boot(dst, len); - if (status != 0) { - printf("\nFPGA: Booting failed "); - switch (status) { - case ERROR_FPGA_PRG_INIT_LOW: - printf("(Timeout: INIT not low after asserting PROGRAM*)\n "); - break; - case ERROR_FPGA_PRG_INIT_HIGH: - printf("(Timeout: INIT not high after deasserting PROGRAM*)\n "); - break; - case ERROR_FPGA_PRG_DONE: - printf("(Timeout: DONE not high after programming FPGA)\n "); - break; - } - - /* display infos on fpgaimage */ - index = 15; - for (i=0; i<4; i++) { - len = dst[index]; - printf("FPGA: %s\n", &(dst[index+1])); - index += len+3; - } - putc ('\n'); - /* delayed reboot */ - for (i=5; i>0; i--) { - printf("Rebooting in %2d seconds \r",i); - for (index=0;index<1000;index++) - udelay(1000); - } - putc('\n'); - do_reset(NULL, 0, 0, NULL); - } - - puts("FPGA: "); - - /* display infos on fpgaimage */ - index = 15; - for (i=0; i<4; i++) { - len = dst[index]; - printf("%s ", &(dst[index+1])); - index += len+3; - } - putc('\n'); - - free(dst); - - /* - * Reset FPGA - */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_FPGA_RESET); - udelay(10); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET); - - return (0); -} - -int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - ulong addr; - - if (argc < 2) - return cmd_usage(cmdtp); - - addr = simple_strtoul(argv[1], NULL, 16); - - return do_fpga_boot((unsigned char *)addr); -} - -U_BOOT_CMD( - fpga, 2, 0, do_fpga, - "boot FPGA", - "address size\n - boot FPGA with gzipped image at <address>" -); - -#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI) -extern struct pci_controller hose; -extern void pci_ixp_init(struct pci_controller * hose); - -void pci_init_board(void) -{ - extern void pci_ixp_init (struct pci_controller *hose); - - pci_ixp_init(&hose); -} -#endif |