diff options
Diffstat (limited to 'board/pn62/pn62.h')
| -rw-r--r-- | board/pn62/pn62.h | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/board/pn62/pn62.h b/board/pn62/pn62.h deleted file mode 100644 index 10290c314..000000000 --- a/board/pn62/pn62.h +++ /dev/null @@ -1,145 +0,0 @@ -/* - * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _PN62_H_ -#define _PN62_H_ - -/* - * Definitions for the Intel Bridge 21554 or 21555. - */ -#define I2155X_VPD_ADDR 0xe6 -#define I2155X_VPD_DATA 0xe8 - -#define I2155X_VPD_START 0x80 -#define I2155X_VPD_SN_START 0x80 -#define I2155X_VPD_SN_SIZE 0x10 -#define I2155X_VPD_MAC0_START 0x90 -#define I2155X_VPD_MAC1_START 0x96 - -#define I2155X_SCRAPAD_ADDR 0xa8 -#define I2155X_SCRAPAD_MAX 8 - -#define I2155X_BAR2_BASE 0x98 -#define I2155X_BAR3_BASE 0x9c -#define I2155X_BAR4_BASE 0xa0 - -#define I2155X_BAR2_SETUP 0xb0 -#define I2155X_BAR3_SETUP 0xb4 -#define I2155X_BAR4_SETUP 0xb8 - -/* - * Interrupt request numbers - */ -#define PN62_IRQ_HOST 0x0 -#define PN62_IRQ_PLX9054 0x1 -#define PN62_IRQ_ETH0 0x2 -#define PN62_IRQ_ETH1 0x3 -#define PN62_IRQ_COM1 0x4 -#define PN62_IRQ_COM2 0x4 - -/* - * Miscellaneous definitons. - */ -#define PN62_SMEM_DEFAULT 0x1f00000 - -/* - * Definitions for boot protocol using Scratchpad registers. - */ -#define BOOT_DONE 0 -#define BOOT_DONE_CLEAR 0x00dead00 -#define BOOT_DONE_ERROR 0xbad0dead -#define BOOT_DONE_U_BOOT 0x12345678 -#define BOOT_DONE_LINUX 0x87654321 -#define BOOT_CMD 1 -#define BOOT_CMD_MOVE 0x1 -#define BOOT_CMD_BOOT 0x2 -#define BOOT_DATA 2 -#define BOOT_PROTO 3 -#define BOOT_PROTO_READY 0x23456789 -#define BOOT_PROTO_CLEAR 0x00000000 -#define BOOT_STATUS 4 - -/* - * LED Definitions: - */ -#define PN62_LED_BASE 0xff800300 -#define PN62_LED_MAX 12 - -/* - * LED0 - 7 mounted on top of board, D1 - D8 - * LED8 - 11 upper four LEDs on the front panel of the board. - */ -#define LED_0 0x00 /* OFF */ -#define LED_1 0x01 /* ON */ -#define LED_SLOW_CLOCK 0x02 /* SLOW 1Hz ish */ -#define LED_nSLOW_CLOCK 0x03 /* inverse of above */ -#define LED_WATCHDOG_OUT 0x06 /* Reset Watchdog level */ -#define LED_WATCHDOG_CLOCK 0x07 /* clock to watchdog */ - -/* - * LED's currently setup in AMD79C973 device as the following: - * LED0 100Mbit - * LED1 LNKSE - * LED2 TX Activity - * LED3 RX Activity - */ -#define LED_E0_LED0 0x08 /* Ethernet Port 0 LED 0 */ -#define LED_E0_LED1 0x09 /* Ethernet Port 0 LED 1 */ -#define LED_E0_LED2 0x0A /* Ethernet Port 0 LED 2 */ -#define LED_E0_LED3 0x0B /* Ethernet Port 0 LED 3 */ -#define LED_E1_LED0 0x0C /* Ethernet Port 1 LED 0 */ -#define LED_E1_LED1 0x0D /* Ethernet Port 1 LED 1 */ -#define LED_E1_LED2 0x0E /* Ethernet Port 1 LED 2 */ -#define LED_E1_LED3 0x0F /* Ethernet Port 1 LED 3 */ -#define LED_STROBE0 0x10 /* Processor Strobe 0 */ -#define LED_STROBE1 0x11 /* Processor Strobe 1 */ -#define LED_STROBE2 0x12 /* Processor Strobe 2 */ -#define LED_STROBE3 0x13 /* Processor Strobe 3 */ -#define LED_STROBE4 0x14 /* Processor Strobe 4 */ -#define LED_STROBE5 0x15 /* Processor Strobe 5 */ -#define LED_STROBE6 0x16 /* Processor Strobe 6 */ -#define LED_STROBE7 0x17 /* Processor Strobe 7 */ -#define LED_HOST_STROBE0 0x18 /* Host strobe 0 */ -#define LED_HOST_STROBE1 0x19 /* Host strobe 1 */ -#define LED_HOST_STROBE2 0x1A /* Host strobe 2 */ -#define LED_HOST_STROBE3 0x1B /* Host strobe 3 */ -#define LED_HOST_STROBE4 0x1C /* Host strobe 4 */ -#define LED_HOST_STROBE5 0x1D /* Host strobe 5 */ -#define LED_HOST_STROBE6 0x1E /* Host strobe 6 */ -#define LED_HOST_STROBE7 0x1F /* Host strobe 7 */ -#define LED_MPC_INT0 0x20 /* MPC8240 INT 0 */ -#define LED_MPC_INT1 0x21 /* MPC8240 INT 1 */ -#define LED_MPC_INT2 0x22 /* MPC8240 INT 2 */ -#define LED_MPC_INT3 0x23 /* MPC8240 INT 3 */ -#define LED_MPC_INT4 0x24 /* MPC8240 INT 4 */ -#define LED_UART0_CS 0x25 /* UART 0 Chip Select */ -#define LED_UART1_CS 0x26 /* UART 1 Chip Select */ -#define LED_SRAM_CS 0x27 /* SRAM Chip Select */ -#define LED_SRAM_WR 0x28 /* SRAM WR Signal */ -#define LED_SRAM_RD 0x29 /* SRAM RD Signal */ -#define LED_MPC_RCS0 0x2A /* MPC8240 RCS0 Signal */ -#define LED_S_PCI_FRAME 0x2B /* Secondary PCI Frame Signal */ -#define LED_MPC_CS0 0x2C /* MPC8240 CS0 Signal */ -#define LED_HOST_INT 0x2D /* MPC8240 to Host Interrupt signal */ -#define LED_LAST_FUNCTION LED_HOST_INT /* last function */ - -/* - * Forward declarations - */ -int i2155x_init (void); -void i2155x_write_scrapad(int idx, u32 val); -u32 i2155x_read_scrapad (int idx); -void i2155x_set_bar_base (int bar, u32 addr); -int i2155x_read_vpd (int offset, int size, unsigned char *data); - -int am79c95x_init (void); - -void set_led (unsigned int number, unsigned int function); -void fatal_error (unsigned int error_code); -void show_startup_phase (int phase); - - -#endif /* _PN62_H_ */ |