diff options
Diffstat (limited to 'arch/blackfin/cpu/initcode.c')
| -rw-r--r-- | arch/blackfin/cpu/initcode.c | 71 |
1 files changed, 36 insertions, 35 deletions
diff --git a/arch/blackfin/cpu/initcode.c b/arch/blackfin/cpu/initcode.c index 1a066806d..ffaf1017d 100644 --- a/arch/blackfin/cpu/initcode.c +++ b/arch/blackfin/cpu/initcode.c @@ -13,12 +13,12 @@ #include <config.h> #include <asm/blackfin.h> +#include <asm/mach-common/bits/watchdog.h> #include <asm/mach-common/bits/bootrom.h> #include <asm/mach-common/bits/core.h> +#include <asm/serial.h> -#define BUG() while (1) { asm volatile("emuexcpt;"); } - -#include "serial.h" +#define BUG() while (1) asm volatile("emuexcpt;"); #ifndef __ADSPBF60x__ #include <asm/mach-common/bits/ebiu.h> @@ -193,17 +193,12 @@ static inline void serial_init(void) } #endif +#if CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS if (BFIN_DEBUG_EARLY_SERIAL) { - int enabled = serial_early_enabled(uart_base); - serial_early_init(uart_base); - - /* If the UART is off, that means we need to program - * the baud rate ourselves initially. - */ - if (!enabled) - serial_early_set_baud(uart_base, CONFIG_BAUDRATE); + serial_early_set_baud(uart_base, CONFIG_BAUDRATE); } +#endif } __attribute__((always_inline)) @@ -262,7 +257,8 @@ program_nmi_handler(void) "%1 = RETS;" /* Load addr of NMI handler */ "RETS = %0;" /* Restore RETS */ "[%2] = %1;" /* Write NMI handler */ - : "=r"(tmp1), "=r"(tmp2) : "ab"(EVT2) + : "=d"(tmp1), "=d"(tmp2) + : "ab"(EVT2) ); } @@ -462,19 +458,29 @@ program_early_devices(ADI_BOOT_DATA *bs, uint *sdivB, uint *divB, uint *vcoB) if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) { serial_putc('e'); #ifdef __ADSPBF60x__ + /* Reset system event controller */ bfin_write_SEC_GCTL(0x2); + bfin_write_SEC_CCTL(0x2); SSYNC(); + + /* Enable fault event input and system reset action in fault + * controller. Route watchdog timeout event to fault interface. + */ bfin_write_SEC_FCTL(0xc1); + /* Enable watchdog interrupt source */ bfin_write_SEC_SCTL(2, bfin_read_SEC_SCTL(2) | 0x6); - - bfin_write_SEC_CCTL(0x2); SSYNC(); + + /* Enable system event controller */ bfin_write_SEC_GCTL(0x1); bfin_write_SEC_CCTL(0x1); + SSYNC(); #endif + bfin_write_WDOG_CTL(WDDIS); + SSYNC(); bfin_write_WDOG_CNT(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE)); #if CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART - bfin_write_WDOG_CTL(0); + bfin_write_WDOG_CTL(WDEN); #endif serial_putc('f'); } @@ -713,37 +719,32 @@ program_clocks(ADI_BOOT_DATA *bs, bool put_into_srfs) __attribute__((always_inline)) static inline void update_serial_clocks(ADI_BOOT_DATA *bs, uint sdivB, uint divB, uint vcoB) { - serial_putc('a'); - /* Since we've changed the SCLK above, we may need to update * the UART divisors (UART baud rates are based on SCLK). * Do the division by hand as there are no native instructions * for dividing which means we'd generate a libgcc reference. */ - if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { - unsigned int sdivR, vcoR; - int dividend = sdivB * divB * vcoR; - int divisor = vcoB * sdivR; - unsigned int quotient; + unsigned int sdivR, vcoR; + unsigned int dividend; + unsigned int divisor; + unsigned int quotient; - serial_putc('b'); + serial_putc('a'); #ifdef __ADSPBF60x__ - sdivR = bfin_read_CGU_DIV(); - sdivR = ((sdivR >> 8) & 0x1f) * ((sdivR >> 5) & 0x7); - vcoR = (bfin_read_CGU_CTL() >> 8) & 0x7f; + sdivR = bfin_read_CGU_DIV(); + sdivR = ((sdivR >> 8) & 0x1f) * ((sdivR >> 5) & 0x7); + vcoR = (bfin_read_CGU_CTL() >> 8) & 0x7f; #else - sdivR = bfin_read_PLL_DIV() & 0xf; - vcoR = (bfin_read_PLL_CTL() >> 9) & 0x3f; + sdivR = bfin_read_PLL_DIV() & 0xf; + vcoR = (bfin_read_PLL_CTL() >> 9) & 0x3f; #endif - for (quotient = 0; dividend > 0; ++quotient) - dividend -= divisor; - serial_early_put_div(quotient - ANOMALY_05000230); - serial_putc('c'); - } - - serial_putc('d'); + dividend = sdivB * divB * vcoR; + divisor = vcoB * sdivR; + quotient = early_division(dividend, divisor); + serial_early_put_div(quotient - ANOMALY_05000230); + serial_putc('c'); } __attribute__((always_inline)) static inline void |