diff options
| -rw-r--r-- | arch/arm/cpu/armv7/zynq/slcr.c | 35 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-zynq/hardware.h | 10 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-zynq/sys_proto.h | 3 | ||||
| -rw-r--r-- | board/xilinx/zynq/board.c | 37 | ||||
| -rw-r--r-- | drivers/fpga/Makefile | 1 | ||||
| -rw-r--r-- | drivers/fpga/xilinx.c | 37 | ||||
| -rw-r--r-- | drivers/fpga/zynqpl.c | 355 | ||||
| -rw-r--r-- | include/configs/zynq.h | 6 | ||||
| -rw-r--r-- | include/xilinx.h | 4 | ||||
| -rw-r--r-- | include/zynqpl.h | 59 |
10 files changed, 545 insertions, 2 deletions
diff --git a/arch/arm/cpu/armv7/zynq/slcr.c b/arch/arm/cpu/armv7/zynq/slcr.c index 5a8674ab2..52048c676 100644 --- a/arch/arm/cpu/armv7/zynq/slcr.c +++ b/arch/arm/cpu/armv7/zynq/slcr.c @@ -28,6 +28,9 @@ #define SLCR_LOCK_MAGIC 0x767B #define SLCR_UNLOCK_MAGIC 0xDF0D +#define SLCR_IDCODE_MASK 0x1F000 +#define SLCR_IDCODE_SHIFT 12 + static int slcr_lock = 1; /* 1 means locked, 0 means unlocked */ void zynq_slcr_lock(void) @@ -87,3 +90,35 @@ void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk) out: zynq_slcr_lock(); } + +void zynq_slcr_devcfg_disable(void) +{ + zynq_slcr_unlock(); + + /* Disable AXI interface */ + writel(0xFFFFFFFF, &slcr_base->fpga_rst_ctrl); + + /* Set Level Shifters DT618760 */ + writel(0xA, &slcr_base->lvl_shftr_en); + + zynq_slcr_lock(); +} + +void zynq_slcr_devcfg_enable(void) +{ + zynq_slcr_unlock(); + + /* Set Level Shifters DT618760 */ + writel(0xF, &slcr_base->lvl_shftr_en); + + /* Disable AXI interface */ + writel(0x0, &slcr_base->fpga_rst_ctrl); + + zynq_slcr_lock(); +} + +u32 zynq_slcr_get_idcode(void) +{ + return (readl(&slcr_base->pss_idcode) & SLCR_IDCODE_MASK) >> + SLCR_IDCODE_SHIFT; +} diff --git a/arch/arm/include/asm/arch-zynq/hardware.h b/arch/arm/include/asm/arch-zynq/hardware.h index 6af892a78..8b8a91ae6 100644 --- a/arch/arm/include/asm/arch-zynq/hardware.h +++ b/arch/arm/include/asm/arch-zynq/hardware.h @@ -53,11 +53,17 @@ struct slcr_regs { u32 boot_mode; /* 0x25c */ u32 reserved4[116]; u32 trust_zone; /* 0x430 */ /* FIXME */ - u32 reserved5[115]; + u32 reserved5_1[63]; + u32 pss_idcode; /* 0x530 */ + u32 reserved5_2[51]; u32 ddr_urgent; /* 0x600 */ u32 reserved6[6]; u32 ddr_urgent_sel; /* 0x61c */ - u32 reserved7[188]; + u32 reserved7[56]; + u32 mio_pin[54]; /* 0x700 - 0x7D4 */ + u32 reserved8[74]; + u32 lvl_shftr_en; /* 0x900 */ + u32 reserved9[3]; u32 ocm_cfg; /* 0x910 */ }; diff --git a/arch/arm/include/asm/arch-zynq/sys_proto.h b/arch/arm/include/asm/arch-zynq/sys_proto.h index af9e7f8d4..2317121ca 100644 --- a/arch/arm/include/asm/arch-zynq/sys_proto.h +++ b/arch/arm/include/asm/arch-zynq/sys_proto.h @@ -27,6 +27,9 @@ extern void zynq_slcr_lock(void); extern void zynq_slcr_unlock(void); extern void zynq_slcr_cpu_reset(void); extern void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk); +extern void zynq_slcr_devcfg_disable(void); +extern void zynq_slcr_devcfg_enable(void); +extern u32 zynq_slcr_get_idcode(void); /* Driver extern functions */ extern int zynq_sdhci_init(u32 regbase); diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c index 1589d2107..b02c364dc 100644 --- a/board/xilinx/zynq/board.c +++ b/board/xilinx/zynq/board.c @@ -22,15 +22,52 @@ #include <common.h> #include <netdev.h> +#include <zynqpl.h> #include <asm/arch/hardware.h> #include <asm/arch/sys_proto.h> DECLARE_GLOBAL_DATA_PTR; +#ifdef CONFIG_FPGA +Xilinx_desc fpga; + +/* It can be done differently */ +Xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10); +Xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20); +Xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30); +Xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45); +#endif + int board_init(void) { +#ifdef CONFIG_FPGA + u32 idcode; + + idcode = zynq_slcr_get_idcode(); + + switch (idcode) { + case XILINX_ZYNQ_7010: + fpga = fpga010; + break; + case XILINX_ZYNQ_7020: + fpga = fpga020; + break; + case XILINX_ZYNQ_7030: + fpga = fpga030; + break; + case XILINX_ZYNQ_7045: + fpga = fpga045; + break; + } +#endif + icache_enable(); +#ifdef CONFIG_FPGA + fpga_init(); + fpga_add(fpga_xilinx, &fpga); +#endif + return 0; } diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index b48f623c1..0b51dcdef 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -30,6 +30,7 @@ COBJS-y += fpga.o COBJS-$(CONFIG_FPGA_SPARTAN2) += spartan2.o COBJS-$(CONFIG_FPGA_SPARTAN3) += spartan3.o COBJS-$(CONFIG_FPGA_VIRTEX2) += virtex2.o +COBJS-$(CONFIG_FPGA_ZYNQPL) += zynqpl.o COBJS-$(CONFIG_FPGA_XILINX) += xilinx.o COBJS-$(CONFIG_FPGA_LATTICE) += ivm_core.o lattice.o ifdef CONFIG_FPGA_ALTERA diff --git a/drivers/fpga/xilinx.c b/drivers/fpga/xilinx.c index df5f9bf91..496aa2f6e 100644 --- a/drivers/fpga/xilinx.c +++ b/drivers/fpga/xilinx.c @@ -1,4 +1,6 @@ /* + * (C) Copyright 2012-2013, Xilinx, Michal Simek + * * (C) Copyright 2002 * Rich Ireland, Enterasys Networks, rireland@enterasys.com. * Keith Outwater, keith_outwater@mvis.com @@ -31,6 +33,7 @@ #include <virtex2.h> #include <spartan2.h> #include <spartan3.h> +#include <zynqpl.h> #if 0 #define FPGA_DEBUG @@ -172,6 +175,16 @@ int xilinx_load(Xilinx_desc *desc, const void *buf, size_t bsize) __FUNCTION__); #endif break; + case xilinx_zynq: +#if defined(CONFIG_FPGA_ZYNQPL) + PRINTF("%s: Launching the Zynq PL Loader...\n", + __func__); + ret_val = zynq_load(desc, buf, bsize); +#else + printf("%s: No support for Zynq devices.\n", + __func__); +#endif + break; default: printf ("%s: Unsupported family type, %d\n", @@ -219,6 +232,16 @@ int xilinx_dump(Xilinx_desc *desc, const void *buf, size_t bsize) __FUNCTION__); #endif break; + case xilinx_zynq: +#if defined(CONFIG_FPGA_ZYNQPL) + PRINTF("%s: Launching the Zynq PL Reader...\n", + __func__); + ret_val = zynq_dump(desc, buf, bsize); +#else + printf("%s: No support for Zynq devices.\n", + __func__); +#endif + break; default: printf ("%s: Unsupported family type, %d\n", @@ -244,6 +267,9 @@ int xilinx_info (Xilinx_desc * desc) case Xilinx_Virtex2: printf ("Virtex-II\n"); break; + case xilinx_zynq: + printf("Zynq PL\n"); + break; /* Add new family types here */ default: printf ("Unknown family type, %d\n", desc->family); @@ -269,6 +295,9 @@ int xilinx_info (Xilinx_desc * desc) case master_selectmap: printf ("Master SelectMap Mode\n"); break; + case devcfg: + printf("Device configuration interface (Zynq)\n"); + break; /* Add new interface types here */ default: printf ("Unsupported interface type, %d\n", desc->iface); @@ -308,6 +337,14 @@ int xilinx_info (Xilinx_desc * desc) __FUNCTION__); #endif break; + case xilinx_zynq: +#if defined(CONFIG_FPGA_ZYNQPL) + zynq_info(desc); +#else + /* just in case */ + printf("%s: No support for Zynq devices.\n", + __func__); +#endif /* Add new family types here */ default: /* we don't need a message here - we give one up above */ diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c new file mode 100644 index 000000000..8feccdea4 --- /dev/null +++ b/drivers/fpga/zynqpl.c @@ -0,0 +1,355 @@ +/* + * (C) Copyright 2012-2013, Xilinx, Michal Simek + * + * (C) Copyright 2012 + * Joe Hershberger <joe.hershberger@ni.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <zynqpl.h> +#include <asm/arch/hardware.h> +#include <asm/arch/sys_proto.h> + +#define DEVCFG_CTRL_PCFG_PROG_B 0x40000000 +#define DEVCFG_ISR_FATAL_ERROR_MASK 0x00740040 +#define DEVCFG_ISR_ERROR_FLAGS_MASK 0x00340840 +#define DEVCFG_ISR_RX_FIFO_OV 0x00040000 +#define DEVCFG_ISR_DMA_DONE 0x00002000 +#define DEVCFG_ISR_PCFG_DONE 0x00000004 +#define DEVCFG_STATUS_DMA_CMD_Q_F 0x80000000 +#define DEVCFG_STATUS_DMA_CMD_Q_E 0x40000000 +#define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000 +#define DEVCFG_STATUS_PCFG_INIT 0x00000010 +#define DEVCFG_MCTRL_RFIFO_FLUSH 0x00000002 +#define DEVCFG_MCTRL_WFIFO_FLUSH 0x00000001 + +#ifndef CONFIG_SYS_FPGA_WAIT +#define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */ +#endif + +#ifndef CONFIG_SYS_FPGA_PROG_TIME +#define CONFIG_SYS_FPGA_PROG_TIME CONFIG_SYS_HZ /* 1 s */ +#endif + +int zynq_info(Xilinx_desc *desc) +{ + return FPGA_SUCCESS; +} + +#define DUMMY_WORD 0xffffffff + +/* Xilinx binary format header */ +static const u32 bin_format[] = { + DUMMY_WORD, /* Dummy words */ + DUMMY_WORD, + DUMMY_WORD, + DUMMY_WORD, + DUMMY_WORD, + DUMMY_WORD, + DUMMY_WORD, + DUMMY_WORD, + 0x000000bb, /* Sync word */ + 0x11220044, /* Sync word */ + DUMMY_WORD, + DUMMY_WORD, + 0xaa995566, /* Sync word */ +}; + +#define SWAP_NO 1 +#define SWAP_DONE 2 + +/* + * Load the whole word from unaligned buffer + * Keep in your mind that it is byte loading on little-endian system + */ +static u32 load_word(const void *buf, u32 swap) +{ + u32 word = 0; + u8 *bitc = (u8 *)buf; + int p; + + if (swap == SWAP_NO) { + for (p = 0; p < 4; p++) { + word <<= 8; + word |= bitc[p]; + } + } else { + for (p = 3; p >= 0; p--) { + word <<= 8; + word |= bitc[p]; + } + } + + return word; +} + +static u32 check_header(const void *buf) +{ + u32 i, pattern; + int swap = SWAP_NO; + u32 *test = (u32 *)buf; + + debug("%s: Let's check bitstream header\n", __func__); + + /* Checking that passing bin is not a bitstream */ + for (i = 0; i < ARRAY_SIZE(bin_format); i++) { + pattern = load_word(&test[i], swap); + + /* + * Bitstreams in binary format are swapped + * compare to regular bistream. + * Do not swap dummy word but if swap is done assume + * that parsing buffer is binary format + */ + if ((__swab32(pattern) != DUMMY_WORD) && + (__swab32(pattern) == bin_format[i])) { + pattern = __swab32(pattern); + swap = SWAP_DONE; + debug("%s: data swapped - let's swap\n", __func__); + } + + debug("%s: %d/%x: pattern %x/%x bin_format\n", __func__, i, + (u32)&test[i], pattern, bin_format[i]); + if (pattern != bin_format[i]) { + debug("%s: Bitstream is not recognized\n", __func__); + return 0; + } + } + debug("%s: Found bitstream header at %x %s swapinng\n", __func__, + (u32)buf, swap == SWAP_NO ? "without" : "with"); + + return swap; +} + +static void *check_data(u8 *buf, size_t bsize, u32 *swap) +{ + u32 word, p = 0; /* possition */ + + /* Because buf doesn't need to be aligned let's read it by chars */ + for (p = 0; p < bsize; p++) { + word = load_word(&buf[p], SWAP_NO); + debug("%s: word %x %x/%x\n", __func__, word, p, (u32)&buf[p]); + + /* Find the first bitstream dummy word */ + if (word == DUMMY_WORD) { + debug("%s: Found dummy word at position %x/%x\n", + __func__, p, (u32)&buf[p]); + *swap = check_header(&buf[p]); + if (*swap) { + /* FIXME add full bitstream checking here */ + return &buf[p]; + } + } + /* Loop can be huge - support CTRL + C */ + if (ctrlc()) + return 0; + } + return 0; +} + + +int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize) +{ + unsigned long ts; /* Timestamp */ + u32 partialbit = 0; + u32 i, control, isr_status, status, swap, diff; + u32 *buf_start; + + /* Detect if we are going working with partial or full bitstream */ + if (bsize != desc->size) { + printf("%s: Working with partial bitstream\n", __func__); + partialbit = 1; + } + + buf_start = check_data((u8 *)buf, bsize, &swap); + if (!buf_start) + return FPGA_FAIL; + + /* Check if data is postpone from start */ + diff = (u32)buf_start - (u32)buf; + if (diff) { + printf("%s: Bitstream is not validated yet (diff %x)\n", + __func__, diff); + return FPGA_FAIL; + } + + if ((u32)buf_start & 0x3) { + u32 *new_buf = (u32 *)((u32)buf & ~0x3); + + printf("%s: Align buffer at %x to %x(swap %d)\n", __func__, + (u32)buf_start, (u32)new_buf, swap); + + for (i = 0; i < (bsize/4); i++) + new_buf[i] = load_word(&buf_start[i], swap); + + swap = SWAP_DONE; + buf = new_buf; + } else if (swap != SWAP_DONE) { + /* For bitstream which are aligned */ + u32 *new_buf = (u32 *)buf; + + printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__, + swap); + + for (i = 0; i < (bsize/4); i++) + new_buf[i] = load_word(&buf_start[i], swap); + + swap = SWAP_DONE; + } + + if (!partialbit) { + zynq_slcr_devcfg_disable(); + + /* Setting PCFG_PROG_B signal to high */ + control = readl(&devcfg_base->ctrl); + writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); + /* Setting PCFG_PROG_B signal to low */ + writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); + + /* Polling the PCAP_INIT status for Reset */ + ts = get_timer(0); + while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) { + if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { + printf("%s: Timeout wait for INIT to clear\n", + __func__); + return FPGA_FAIL; + } + } + + /* Setting PCFG_PROG_B signal to high */ + writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); + + /* Polling the PCAP_INIT status for Set */ + ts = get_timer(0); + while (!(readl(&devcfg_base->status) & + DEVCFG_STATUS_PCFG_INIT)) { + if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { + printf("%s: Timeout wait for INIT to set\n", + __func__); + return FPGA_FAIL; + } + } + } + + isr_status = readl(&devcfg_base->int_sts); + + /* Clear it all, so if Boot ROM comes back, it can proceed */ + writel(0xFFFFFFFF, &devcfg_base->int_sts); + + if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) { + debug("%s: Fatal errors in PCAP 0x%X\n", __func__, isr_status); + + /* If RX FIFO overflow, need to flush RX FIFO first */ + if (isr_status & DEVCFG_ISR_RX_FIFO_OV) { + writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl); + writel(0xFFFFFFFF, &devcfg_base->int_sts); + } + return FPGA_FAIL; + } + + status = readl(&devcfg_base->status); + + debug("%s: Status = 0x%08X\n", __func__, status); + + if (status & DEVCFG_STATUS_DMA_CMD_Q_F) { + debug("%s: Error: device busy\n", __func__); + return FPGA_FAIL; + } + + debug("%s: Device ready\n", __func__); + + if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) { + if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) { + /* Error state, transfer cannot occur */ + debug("%s: ISR indicates error\n", __func__); + return FPGA_FAIL; + } else { + /* Clear out the status */ + writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts); + } + } + + if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) { + /* Clear the count of completed DMA transfers */ + writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status); + } + + debug("%s: Source = 0x%08X\n", __func__, (u32)buf); + debug("%s: Size = %zu\n", __func__, bsize); + + /* Set up the transfer */ + writel((u32)buf | 1, &devcfg_base->dma_src_addr); + writel(0xFFFFFFFF, &devcfg_base->dma_dst_addr); + writel(bsize >> 2, &devcfg_base->dma_src_len); + writel(0, &devcfg_base->dma_dst_len); + + isr_status = readl(&devcfg_base->int_sts); + + /* Polling the PCAP_INIT status for Set */ + ts = get_timer(0); + while (!(isr_status & DEVCFG_ISR_DMA_DONE)) { + if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) { + debug("%s: Error: isr = 0x%08X\n", __func__, + isr_status); + debug("%s: Write count = 0x%08X\n", __func__, + readl(&devcfg_base->write_count)); + debug("%s: Read count = 0x%08X\n", __func__, + readl(&devcfg_base->read_count)); + + return FPGA_FAIL; + } + if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) { + printf("%s: Timeout wait for DMA to complete\n", + __func__); + return FPGA_FAIL; + } + isr_status = readl(&devcfg_base->int_sts); + } + + debug("%s: DMA transfer is done\n", __func__); + + /* Check FPGA configuration completion */ + ts = get_timer(0); + while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) { + if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { + printf("%s: Timeout wait for FPGA to config\n", + __func__); + return FPGA_FAIL; + } + isr_status = readl(&devcfg_base->int_sts); + } + + debug("%s: FPGA config done\n", __func__); + + /* Clear out the DMA status */ + writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts); + + if (!partialbit) + zynq_slcr_devcfg_enable(); + + return FPGA_SUCCESS; +} + +int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize) +{ + return FPGA_FAIL; +} diff --git a/include/configs/zynq.h b/include/configs/zynq.h index f1f182edf..38f04f642 100644 --- a/include/configs/zynq.h +++ b/include/configs/zynq.h @@ -88,6 +88,12 @@ # define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */ #endif +/* Enable the PL to be downloaded */ +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_ZYNQPL +#define CONFIG_CMD_FPGA + #define CONFIG_BOOTP_SERVERIP #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY diff --git a/include/xilinx.h b/include/xilinx.h index 5f25b7a8a..592cbea1f 100644 --- a/include/xilinx.h +++ b/include/xilinx.h @@ -33,10 +33,12 @@ #define CONFIG_SYS_VIRTEX_E CONFIG_SYS_FPGA_DEV( 0x2 ) #define CONFIG_SYS_VIRTEX2 CONFIG_SYS_FPGA_DEV( 0x4 ) #define CONFIG_SYS_SPARTAN3 CONFIG_SYS_FPGA_DEV( 0x8 ) +#define CONFIG_SYS_ZYNQ CONFIG_SYS_FPGA_DEV(0x10) #define CONFIG_SYS_XILINX_SPARTAN2 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_SPARTAN2) #define CONFIG_SYS_XILINX_VIRTEX_E (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_VIRTEX_E) #define CONFIG_SYS_XILINX_VIRTEX2 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_VIRTEX2) #define CONFIG_SYS_XILINX_SPARTAN3 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_SPARTAN3) +#define CONFIG_SYS_XILINX_ZYNQ (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_ZYNQ) /* XXX - Add new models here */ @@ -59,6 +61,7 @@ typedef enum { /* typedef Xilinx_iface */ jtag_mode, /* jtag/tap serial (not used ) */ master_selectmap, /* master SelectMap (virtex2) */ slave_selectmap, /* slave SelectMap (virtex2) */ + devcfg, /* devcfg interface (zynq) */ max_xilinx_iface_type /* insert all new types before this */ } Xilinx_iface; /* end, typedef Xilinx_iface */ @@ -68,6 +71,7 @@ typedef enum { /* typedef Xilinx_Family */ Xilinx_VirtexE, /* Virtex-E Family */ Xilinx_Virtex2, /* Virtex2 Family */ Xilinx_Spartan3, /* Spartan-III Family */ + xilinx_zynq, /* Zynq Family */ max_xilinx_type /* insert all new types before this */ } Xilinx_Family; /* end, typedef Xilinx_Family */ diff --git a/include/zynqpl.h b/include/zynqpl.h new file mode 100644 index 000000000..bc9b94815 --- /dev/null +++ b/include/zynqpl.h @@ -0,0 +1,59 @@ +/* + * (C) Copyright 2012-2013, Xilinx, Michal Simek + * + * (C) Copyright 2012 + * Joe Hershberger <joe.hershberger@ni.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _ZYNQPL_H_ +#define _ZYNQPL_H_ + +#include <xilinx.h> + +extern int zynq_load(Xilinx_desc *desc, const void *image, size_t size); +extern int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize); +extern int zynq_info(Xilinx_desc *desc); + +#define XILINX_ZYNQ_7010 0x2 +#define XILINX_ZYNQ_7020 0x7 +#define XILINX_ZYNQ_7030 0xc +#define XILINX_ZYNQ_7045 0x11 + +/* Device Image Sizes */ +#define XILINX_XC7Z010_SIZE 16669920/8 +#define XILINX_XC7Z020_SIZE 32364512/8 +#define XILINX_XC7Z030_SIZE 47839328/8 +#define XILINX_XC7Z045_SIZE 106571232/8 + +/* Descriptor Macros */ +#define XILINX_XC7Z010_DESC(cookie) \ +{ xilinx_zynq, devcfg, XILINX_XC7Z010_SIZE, NULL, cookie } + +#define XILINX_XC7Z020_DESC(cookie) \ +{ xilinx_zynq, devcfg, XILINX_XC7Z020_SIZE, NULL, cookie } + +#define XILINX_XC7Z030_DESC(cookie) \ +{ xilinx_zynq, devcfg, XILINX_XC7Z030_SIZE, NULL, cookie } + +#define XILINX_XC7Z045_DESC(cookie) \ +{ xilinx_zynq, devcfg, XILINX_XC7Z045_SIZE, NULL, cookie } + +#endif /* _ZYNQPL_H_ */ |