16 files changed, 236 insertions, 168 deletions

diff --git a/arch/arm/cpu/arm_cortexa8/omap3/Makefile b/arch/arm/cpu/arm_cortexa8/omap3/Makefile
index 136b163ad..1e80eb3b7 100644
--- a/arch/arm/cpu/arm_cortexa8/omap3/Makefile
+++ b/arch/arm/cpu/arm_cortexa8/omap3/Makefile
@@ -37,8 +37,10 @@ COBJS	+= syslib.o
 COBJS	+= sys_info.o
 COBJS	+= timer.o
 
+COBJS-$(CONFIG_SDRC)	+= sdrc.o
+
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+OBJS	:= $(addprefix $(obj),$(COBJS) $(COBJS-y) $(SOBJS))
 
 all:	 $(obj).depend $(LIB)
 
diff --git a/arch/arm/cpu/arm_cortexa8/omap3/board.c b/arch/arm/cpu/arm_cortexa8/omap3/board.c
index 69a08fd5f..d2500ca3b 100644
--- a/arch/arm/cpu/arm_cortexa8/omap3/board.c
+++ b/arch/arm/cpu/arm_cortexa8/omap3/board.c
@@ -40,8 +40,6 @@
 
 extern omap3_sysinfo sysinfo;
 
-extern u32 is_mem_sdr(void);
-
 /******************************************************************************
  * Routine: delay
  * Description: spinning delay to use before udelay works
@@ -233,7 +231,7 @@ void s_init(void)
 	per_clocks_enable();
 
 	if (!in_sdram)
-		sdrc_init();
+		mem_init();
 }
 
 /******************************************************************************
@@ -274,37 +272,6 @@ void watchdog_init(void)
 }
 
 /******************************************************************************
- * Routine: dram_init
- * Description: sets uboots idea of sdram size
- *****************************************************************************/
-int dram_init(void)
-{
-	DECLARE_GLOBAL_DATA_PTR;
-	unsigned int size0 = 0, size1 = 0;
-
-	size0 = get_sdr_cs_size(CS0);
-
-	/*
-	 * If a second bank of DDR is attached to CS1 this is
-	 * where it can be started.  Early init code will init
-	 * memory on CS0.
-	 */
-	if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
-		do_sdrc_init(CS1, NOT_EARLY);
-		make_cs1_contiguous();
-
-		size1 = get_sdr_cs_size(CS1);
-	}
-
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = size0;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
-	gd->bd->bi_dram[1].size = size1;
-
-	return 0;
-}
-
-/******************************************************************************
  * Dummy function to handle errors for EABI incompatibility
  *****************************************************************************/
 void abort(void)
diff --git a/arch/arm/cpu/arm_cortexa8/omap3/mem.c b/arch/arm/cpu/arm_cortexa8/omap3/mem.c
index dfb7e4c2a..bd914b0ee 100644
--- a/arch/arm/cpu/arm_cortexa8/omap3/mem.c
+++ b/arch/arm/cpu/arm_cortexa8/omap3/mem.c
@@ -79,26 +79,6 @@ static const u32 gpmc_onenand[GPMC_MAX_REG] = {
 
 #endif
 
-static struct sdrc *sdrc_base = (struct sdrc *)OMAP34XX_SDRC_BASE;
-
-/**************************************************************************
- * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
- *  command line mem=xyz use all memory with out discontinuous support
- *  compiled in.  Could do it at the ATAG, but there really is two banks...
- * Called as part of 2nd phase DDR init.
- **************************************************************************/
-void make_cs1_contiguous(void)
-{
-	u32 size, a_add_low, a_add_high;
-
-	size = get_sdr_cs_size(CS0);
-	size >>= 25;	/* divide by 32 MiB to find size to offset CS1 */
-	a_add_high = (size & 3) << 8;	/* set up low field */
-	a_add_low = (size & 0x3C) >> 2;	/* set up high field */
-	writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
-
-}
-
 /********************************************************
  *  mem_ok() - test used to see if timings are correct
  *             for a part. Helps in guessing which part
@@ -123,76 +103,6 @@ u32 mem_ok(u32 cs)
 		return 1;
 }
 
-/********************************************************
- *  sdrc_init() - init the sdrc chip selects CS0 and CS1
- *  - early init routines, called from flash or
- *  SRAM.
- *******************************************************/
-void sdrc_init(void)
-{
-	/* only init up first bank here */
-	do_sdrc_init(CS0, EARLY_INIT);
-}
-
-/*************************************************************************
- * do_sdrc_init(): initialize the SDRAM for use.
- *  -code sets up SDRAM basic SDRC timings for CS0
- *  -optimal settings can be placed here, or redone after i2c
- *      inspection of board info
- *
- *  - code called once in C-Stack only context for CS0 and a possible 2nd
- *      time depending on memory configuration from stack+global context
- **************************************************************************/
-
-void do_sdrc_init(u32 cs, u32 early)
-{
-	struct sdrc_actim *sdrc_actim_base;
-
-	if(cs)
-		sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
-	else
-		sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
-
-	if (early) {
-		/* reset sdrc controller */
-		writel(SOFTRESET, &sdrc_base->sysconfig);
-		wait_on_value(RESETDONE, RESETDONE, &sdrc_base->status,
-			      12000000);
-		writel(0, &sdrc_base->sysconfig);
-
-		/* setup sdrc to ball mux */
-		writel(SDRC_SHARING, &sdrc_base->sharing);
-
-		/* Disable Power Down of CKE cuz of 1 CKE on combo part */
-		writel(WAKEUPPROC | PWDNEN | SRFRONRESET | PAGEPOLICY_HIGH,
-				&sdrc_base->power);
-
-		writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
-		sdelay(0x20000);
-	}
-
-	writel(RASWIDTH_13BITS | CASWIDTH_10BITS | ADDRMUXLEGACY |
-		RAMSIZE_128 | BANKALLOCATION | B32NOT16 | B32NOT16 |
-		DEEPPD | DDR_SDRAM, &sdrc_base->cs[cs].mcfg);
-	writel(ARCV | ARE_ARCV_1, &sdrc_base->cs[cs].rfr_ctrl);
-	writel(V_ACTIMA_165, &sdrc_actim_base->ctrla);
-	writel(V_ACTIMB_165, &sdrc_actim_base->ctrlb);
-
-	writel(CMD_NOP, &sdrc_base ->cs[cs].manual);
-	writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
-	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-
-	/*
-	 * CAS latency 3, Write Burst = Read Burst, Serial Mode,
-	 * Burst length = 4
-	 */
-	writel(CASL3 | BURSTLENGTH4, &sdrc_base->cs[cs].mr);
-
-	if (!mem_ok(cs))
-		writel(0, &sdrc_base->cs[cs].mcfg);
-}
-
 void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
 			u32 size)
 {
diff --git a/arch/arm/cpu/arm_cortexa8/omap3/sdrc.c b/arch/arm/cpu/arm_cortexa8/omap3/sdrc.c
new file mode 100644
index 000000000..96fd990c7
--- /dev/null
+++ b/arch/arm/cpu/arm_cortexa8/omap3/sdrc.c
@@ -0,0 +1,202 @@
+/*
+ * Functions related to OMAP3 SDRC.
+ *
+ * This file has been created after exctracting and consolidating
+ * the SDRC related content from mem.c and board.c, also created
+ * generic init function (mem_init).
+ *
+ * Copyright (C) 2004-2010
+ * Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author :
+ *     Vaibhav Hiremath <hvaibhav@ti.com>
+ *
+ * Original implementation by (mem.c, board.c) :
+ *      Sunil Kumar <sunilsaini05@gmail.com>
+ *      Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *      Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+
+extern omap3_sysinfo sysinfo;
+
+static struct sdrc *sdrc_base = (struct sdrc *)OMAP34XX_SDRC_BASE;
+
+/*
+ * is_mem_sdr -
+ *  - Return 1 if mem type in use is SDR
+ */
+u32 is_mem_sdr(void)
+{
+	if (readl(&sdrc_base->cs[CS0].mr) == SDRC_MR_0_SDR)
+		return 1;
+	return 0;
+}
+
+/*
+ * make_cs1_contiguous -
+ *  - For es2 and above remap cs1 behind cs0 to allow command line
+ *    mem=xyz use all memory with out discontinuous support compiled in.
+ *    Could do it at the ATAG, but there really is two banks...
+ *  - Called as part of 2nd phase DDR init.
+ */
+void make_cs1_contiguous(void)
+{
+	u32 size, a_add_low, a_add_high;
+
+	size = get_sdr_cs_size(CS0);
+	size >>= 25;	/* divide by 32 MiB to find size to offset CS1 */
+	a_add_high = (size & 3) << 8;	/* set up low field */
+	a_add_low = (size & 0x3C) >> 2;	/* set up high field */
+	writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
+
+}
+
+
+/*
+ * get_sdr_cs_size -
+ *  - Get size of chip select 0/1
+ */
+u32 get_sdr_cs_size(u32 cs)
+{
+	u32 size;
+
+	/* get ram size field */
+	size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
+	size &= 0x3FF;		/* remove unwanted bits */
+	size <<= 21;		/* multiply by 2 MiB to find size in MB */
+	return size;
+}
+
+/*
+ * get_sdr_cs_offset -
+ *  - Get offset of cs from cs0 start
+ */
+u32 get_sdr_cs_offset(u32 cs)
+{
+	u32 offset;
+
+	if (!cs)
+		return 0;
+
+	offset = readl(&sdrc_base->cs_cfg);
+	offset = (offset & 15) << 27 | (offset & 0x30) >> 17;
+
+	return offset;
+}
+
+/*
+ * do_sdrc_init -
+ *  - Initialize the SDRAM for use.
+ *  - Sets up SDRC timings for CS0
+ *  - code called once in C-Stack only context for CS0 and a possible 2nd
+ *    time depending on memory configuration from stack+global context
+ */
+void do_sdrc_init(u32 cs, u32 early)
+{
+	struct sdrc_actim *sdrc_actim_base;
+
+	if (cs)
+		sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
+	else
+		sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
+
+	if (early) {
+		/* reset sdrc controller */
+		writel(SOFTRESET, &sdrc_base->sysconfig);
+		wait_on_value(RESETDONE, RESETDONE, &sdrc_base->status,
+				12000000);
+		writel(0, &sdrc_base->sysconfig);
+
+		/* setup sdrc to ball mux */
+		writel(SDRC_SHARING, &sdrc_base->sharing);
+
+		/* Disable Power Down of CKE cuz of 1 CKE on combo part */
+		writel(WAKEUPPROC | SRFRONRESET | PAGEPOLICY_HIGH,
+				&sdrc_base->power);
+
+		writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
+		sdelay(0x20000);
+	}
+
+	writel(RASWIDTH_13BITS | CASWIDTH_10BITS | ADDRMUXLEGACY |
+			RAMSIZE_128 | BANKALLOCATION | B32NOT16 | B32NOT16 |
+			DEEPPD | DDR_SDRAM, &sdrc_base->cs[cs].mcfg);
+	writel(ARCV | ARE_ARCV_1, &sdrc_base->cs[cs].rfr_ctrl);
+	writel(V_ACTIMA_165, &sdrc_actim_base->ctrla);
+	writel(V_ACTIMB_165, &sdrc_actim_base->ctrlb);
+
+	writel(CMD_NOP, &sdrc_base->cs[cs].manual);
+	writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
+	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+
+	/*
+	 * CAS latency 3, Write Burst = Read Burst, Serial Mode,
+	 * Burst length = 4
+	 */
+	writel(CASL3 | BURSTLENGTH4, &sdrc_base->cs[cs].mr);
+
+	if (!mem_ok(cs))
+		writel(0, &sdrc_base->cs[cs].mcfg);
+}
+
+/*
+ * dram_init -
+ *  - Sets uboots idea of sdram size
+ */
+int dram_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	unsigned int size0 = 0, size1 = 0;
+
+	size0 = get_sdr_cs_size(CS0);
+	/*
+	 * If a second bank of DDR is attached to CS1 this is
+	 * where it can be started.  Early init code will init
+	 * memory on CS0.
+	 */
+	if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
+		do_sdrc_init(CS1, NOT_EARLY);
+		make_cs1_contiguous();
+
+		size1 = get_sdr_cs_size(CS1);
+	}
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = size0;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
+	gd->bd->bi_dram[1].size = size1;
+
+	return 0;
+}
+
+/*
+ * mem_init -
+ *  - Init the sdrc chip,
+ *  - Selects CS0 and CS1,
+ */
+void mem_init(void)
+{
+	/* only init up first bank here */
+	do_sdrc_init(CS0, EARLY_INIT);
+}
diff --git a/arch/arm/cpu/arm_cortexa8/omap3/sys_info.c b/arch/arm/cpu/arm_cortexa8/omap3/sys_info.c
index 08fb32eaa..1df4401d4 100644
--- a/arch/arm/cpu/arm_cortexa8/omap3/sys_info.c
+++ b/arch/arm/cpu/arm_cortexa8/omap3/sys_info.c
@@ -32,7 +32,6 @@
 #include <i2c.h>
 
 extern omap3_sysinfo sysinfo;
-static struct sdrc *sdrc_base = (struct sdrc *)OMAP34XX_SDRC_BASE;
 static struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
 static char *rev_s[CPU_3XX_MAX_REV] = {
 				"1.0",
@@ -104,46 +103,6 @@ u32 get_cpu_rev(void)
 	}
 }
 
-/****************************************************
- * is_mem_sdr() - return 1 if mem type in use is SDR
- ****************************************************/
-u32 is_mem_sdr(void)
-{
-	if (readl(&sdrc_base->cs[CS0].mr) == SDRC_MR_0_SDR)
-		return 1;
-	return 0;
-}
-
-/***********************************************************************
- * get_cs0_size() - get size of chip select 0/1
- ************************************************************************/
-u32 get_sdr_cs_size(u32 cs)
-{
-	u32 size;
-
-	/* get ram size field */
-	size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
-	size &= 0x3FF;		/* remove unwanted bits */
-	size <<= 21;		/* multiply by 2 MiB to find size in MB */
-	return size;
-}
-
-/***********************************************************************
- * get_sdr_cs_offset() - get offset of cs from cs0 start
- ************************************************************************/
-u32 get_sdr_cs_offset(u32 cs)
-{
-	u32 offset;
-
-	if (!cs)
-		return 0;
-
-	offset = readl(&sdrc_base->cs_cfg);
-	offset = (offset & 15) << 27 | (offset & 0x30) >> 17;
-
-	return offset;
-}
-
 /***************************************************************************
  *  get_gpmc0_base() - Return current address hardware will be
  *     fetching from. The below effectively gives what is correct, its a bit
diff --git a/arch/arm/include/asm/arch-omap3/cpu.h b/arch/arm/include/asm/arch-omap3/cpu.h
index aa8de3245..ce16da7f8 100644
--- a/arch/arm/include/asm/arch-omap3/cpu.h
+++ b/arch/arm/include/asm/arch-omap3/cpu.h
@@ -215,6 +215,7 @@ struct sdrc {
 	u8 res4[0xC];
 	struct sdrc_cs cs[2];	/* 0x80 || 0xB0 */
 };
+
 #endif /* __ASSEMBLY__ */
 #endif /* __KERNEL_STRICT_NAMES */
 
diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
index 9439758e4..a78cf9f59 100644
--- a/arch/arm/include/asm/arch-omap3/mem.h
+++ b/arch/arm/include/asm/arch-omap3/mem.h
@@ -270,4 +270,17 @@ enum {
 #define PISMO1_ONEN_BASE	ONENAND_MAP
 #define DBG_MPDB_BASE		DEBUG_BASE
 
+#ifndef __ASSEMBLY__
+
+/* Function prototypes */
+void mem_init(void);
+
+u32 is_mem_sdr(void);
+u32 mem_ok(u32 cs);
+
+u32 get_sdr_cs_size(u32);
+u32 get_sdr_cs_offset(u32);
+
+#endif	/* __ASSEMBLY__ */
+
 #endif /* endif _MEM_H_ */
diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
index 34bd515b0..4608f3063 100644
--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
@@ -46,8 +46,6 @@ u32 get_sysboot_value(void);
 u32 is_gpmc_muxed(void);
 u32 get_gpmc0_type(void);
 u32 get_gpmc0_width(void);
-u32 get_sdr_cs_size(u32);
-u32 get_sdr_cs_offset(u32);
 u32 is_running_in_sdram(void);
 u32 is_running_in_sram(void);
 u32 is_running_in_flash(void);
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 7d1332f62..1076de6fc 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -38,6 +38,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_DEVKIT8000	1	/* working with DevKit8000 */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 08d79aca3..e018b217c 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -37,6 +37,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_BEAGLE	1	/* working with BEAGLE */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 88af49226..af7c65ad3 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -42,6 +42,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_EVM	1	/* working with EVM */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index a43500b5f..b4418319f 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -29,6 +29,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_OVERO	1	/* working with overo */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 945c053ab..9eba003c2 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -32,6 +32,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_PANDORA	1	/* working with pandora */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h
index b4919db08..d4482d3ae 100644
--- a/include/configs/omap3_sdp3430.h
+++ b/include/configs/omap3_sdp3430.h
@@ -42,6 +42,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_3430SDP	1	/* working with SDP Rev2 */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index ae7ebf9ea..1e88dc02e 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -38,6 +38,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_ZOOM1	1	/* working with Zoom MDK Rev1 */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index c88c732a6..be9daf4fc 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -39,6 +39,8 @@
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_ZOOM2	1	/* working with Zoom II */
 
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>