diff options
54 files changed, 1428 insertions, 135 deletions
diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c b/arch/powerpc/cpu/mpc83xx/cpu_init.c index 0e9ddb8e2..00572de12 100644 --- a/arch/powerpc/cpu/mpc83xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c @@ -315,7 +315,7 @@ void cpu_init_f (volatile immap_t * im) #endif #if defined(CONFIG_USB_EHCI_FSL) && defined(CONFIG_MPC831x) uint32_t temp; - struct usb_ehci *ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR; + struct usb_ehci *ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR; /* Configure interface. */ setbits_be32(&ehci->control, REFSEL_16MHZ | UTMI_PHY_EN); diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c index 39d9409d6..25db899e5 100644 --- a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c @@ -201,3 +201,24 @@ void fsl_serdes_init(void) #endif } + +const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + case SRDS_PLLCR0_RFCK_SEL_161_13: + return "161.1328123"; + default: +#if defined(CONFIG_T4240QDS) + return "???"; +#else + return "122.88"; +#endif + } +} + diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c index 680b5222b..ba22f90a6 100644 --- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c @@ -858,3 +858,20 @@ void fsl_serdes_init(void) } #endif } + +const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + case SRDS_PLLCR0_RFCK_SEL_161_13: + return "161.1328123"; + default: + return "150"; + } +} + diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/common_timing_params.h b/arch/powerpc/cpu/mpc8xxx/ddr/common_timing_params.h index 17d8d9f74..76338d4e6 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/common_timing_params.h +++ b/arch/powerpc/cpu/mpc8xxx/ddr/common_timing_params.h @@ -28,6 +28,7 @@ typedef struct { unsigned int trc_ps; /* maximum = 254 ns + .75 ns = 254750 ps */ unsigned int refresh_rate_ps; + unsigned int extended_op_srt; unsigned int tis_ps; /* byte 32, spd->ca_setup */ unsigned int tih_ps; /* byte 33, spd->ca_hold */ diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c index d7333ba3d..dcfc48aa9 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c @@ -765,6 +765,7 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr, /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts, + const common_timing_params_t *common_dimm, const unsigned int unq_mrs_en) { unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ @@ -782,6 +783,10 @@ static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, rtt_wr = popts->rtt_wr_override_value; else rtt_wr = popts->cs_local_opts[0].odt_rtt_wr; + + if (common_dimm->extended_op_srt) + srt = common_dimm->extended_op_srt; + esdmode2 = (0 | ((rtt_wr & 0x3) << 9) | ((srt & 0x1) << 7) @@ -1626,7 +1631,7 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en); set_ddr_sdram_mode(ddr, popts, common_dimm, cas_latency, additive_latency, unq_mrs_en); - set_ddr_sdram_mode_2(ddr, popts, unq_mrs_en); + set_ddr_sdram_mode_2(ddr, popts, common_dimm, unq_mrs_en); set_ddr_sdram_interval(ddr, popts, common_dimm); set_ddr_data_init(ddr); set_ddr_sdram_clk_cntl(ddr, popts); diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c index d82eb674d..4c8645da5 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c @@ -321,6 +321,10 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * = 3.9 us at ext temperature range */ pdimm->refresh_rate_ps = 7800000; + if ((spd->therm_ref_opt & 0x1) && !(spd->therm_ref_opt & 0x2)) { + pdimm->refresh_rate_ps = 3900000; + pdimm->extended_op_srt = 1; + } /* * min four active window delay time diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c index 3affcee7d..332fe25c4 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c @@ -92,6 +92,7 @@ compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, unsigned int trrd_ps = 0; unsigned int trc_ps = 0; unsigned int refresh_rate_ps = 0; + unsigned int extended_op_srt = 1; unsigned int tis_ps = 0; unsigned int tih_ps = 0; unsigned int tds_ps = 0; @@ -166,6 +167,9 @@ compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, tqhs_ps = max(tqhs_ps, dimm_params[i].tqhs_ps); refresh_rate_ps = max(refresh_rate_ps, dimm_params[i].refresh_rate_ps); + /* extended_op_srt is either 0 or 1, 0 having priority */ + extended_op_srt = min(extended_op_srt, + dimm_params[i].extended_op_srt); /* * Find maximum tdqsq_max_ps to find slowest. @@ -195,6 +199,7 @@ compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, outpdimm->trrd_ps = trrd_ps; outpdimm->trc_ps = trc_ps; outpdimm->refresh_rate_ps = refresh_rate_ps; + outpdimm->extended_op_srt = extended_op_srt; outpdimm->tis_ps = tis_ps; outpdimm->tih_ps = tih_ps; outpdimm->tds_ps = tds_ps; diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/main.c b/arch/powerpc/cpu/mpc8xxx/ddr/main.c index b9ae9509b..34d8bc3ac 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/main.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/main.c @@ -69,7 +69,11 @@ u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) { - int ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, + int ret; + + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); + + ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(generic_spd_eeprom_t)); if (ret) { diff --git a/arch/powerpc/cpu/mpc8xxx/fdt.c b/arch/powerpc/cpu/mpc8xxx/fdt.c index eb7cbbce7..927374529 100644 --- a/arch/powerpc/cpu/mpc8xxx/fdt.c +++ b/arch/powerpc/cpu/mpc8xxx/fdt.c @@ -15,7 +15,9 @@ #include <phy.h> #include <hwconfig.h> -#define FSL_MAX_NUM_USB_CTRLS 2 +#ifndef CONFIG_USB_MAX_CONTROLLER_COUNT +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 +#endif #if defined(CONFIG_MP) && (defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)) static int ft_del_cpuhandle(void *blob, int cpuhandle) @@ -128,7 +130,7 @@ void fdt_fixup_dr_usb(void *blob, bd_t *bd) char str[5]; int i, j; - for (i = 1; i <= FSL_MAX_NUM_USB_CTRLS; i++) { + for (i = 1; i <= CONFIG_USB_MAX_CONTROLLER_COUNT; i++) { int mode_idx = -1, phy_idx = -1; snprintf(str, 5, "%s%d", "usb", i); if (hwconfig(str)) { diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 946ea975b..4cc12ee70 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -133,6 +133,7 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_FSL_IFC_BANK_COUNT 4 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" @@ -153,6 +154,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -162,6 +164,7 @@ #elif defined(CONFIG_P1012) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM @@ -178,6 +181,7 @@ #elif defined(CONFIG_P1013) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 @@ -196,6 +200,7 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_IFC_A002769 @@ -210,6 +215,7 @@ #define CONFIG_SYS_NUM_FMAN 1 #define CONFIG_SYS_NUM_FM1_DTSEC 2 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_QMAN_NUM_PORTALS 3 #define CONFIG_SYS_BMAN_NUM_PORTALS 3 #define CONFIG_SYS_FM_MURAM_SIZE 0x10000 @@ -228,6 +234,7 @@ #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_A005125 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #elif defined(CONFIG_P1021) #define CONFIG_MAX_CPUS 2 @@ -243,6 +250,7 @@ #define MAX_QE_RISC 1 #define QE_NUM_OF_SNUM 28 #define CONFIG_SYS_FSL_ERRATUM_A005125 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #elif defined(CONFIG_P1022) #define CONFIG_MAX_CPUS 2 @@ -250,6 +258,7 @@ #define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -263,6 +272,7 @@ #define CONFIG_SYS_NUM_FMAN 1 #define CONFIG_SYS_NUM_FM1_DTSEC 2 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_QMAN_NUM_PORTALS 3 #define CONFIG_SYS_BMAN_NUM_PORTALS 3 #define CONFIG_SYS_FM_MURAM_SIZE 0x10000 @@ -280,6 +290,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -289,6 +300,7 @@ #elif defined(CONFIG_P1025) #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM @@ -307,6 +319,7 @@ #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 @@ -326,7 +339,7 @@ #define CONFIG_SYS_FSL_RMU #define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 #define CONFIG_SYS_FSL_ERRATUM_A005125 - +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #elif defined(CONFIG_PPC_P2041) /* also supports P2040 */ #define CONFIG_SYS_FSL_QORIQ_CHASSIS1 #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ @@ -338,6 +351,7 @@ #define CONFIG_SYS_NUM_FM1_DTSEC 5 #define CONFIG_SYS_NUM_FM1_10GEC 1 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" @@ -381,6 +395,7 @@ #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 #define CONFIG_SYS_FSL_ERRATUM_USB14 @@ -413,6 +428,7 @@ #define CONFIG_SYS_NUM_FM1_10GEC 1 #define CONFIG_SYS_NUM_FM2_10GEC 1 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 16 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie" @@ -460,6 +476,7 @@ #define CONFIG_SYS_NUM_FM1_DTSEC 5 #define CONFIG_SYS_NUM_FM1_10GEC 1 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" @@ -495,6 +512,7 @@ #define CONFIG_SYS_NUM_FM2_DTSEC 5 #define CONFIG_SYS_NUM_FM2_10GEC 1 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 16 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4" @@ -519,6 +537,7 @@ #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_FSL_DSP_M2_RAM_ADDR 0xb0000000 #define CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 0xff600000 #define CONFIG_SYS_FSL_IFC_BANK_COUNT 3 @@ -535,6 +554,7 @@ #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_FSL_DSP_DDR_ADDR 0x40000000 #define CONFIG_SYS_FSL_DSP_M2_RAM_ADDR 0xb0000000 #define CONFIG_SYS_FSL_DSP_M3_RAM_ADDR 0xc0000000 @@ -581,6 +601,7 @@ #define CONFIG_SYS_FSL_SRDS_4 #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_SYS_NUM_FMAN 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_SYS_PME_CLK 0 #define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_4_7 #define CONFIG_SYS_FSL_IFC_BANK_COUNT 8 @@ -615,6 +636,7 @@ #define CONFIG_SYS_FSL_SRDS_2 #define CONFIG_SYS_FSL_SEC_COMPAT 4 #define CONFIG_SYS_NUM_FMAN 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_FM1_CLK 0 #define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_4_7 #define CONFIG_SYS_FSL_IFC_BANK_COUNT 4 @@ -637,6 +659,7 @@ #define CONFIG_SYS_NUM_FM1_DTSEC 6 #define CONFIG_SYS_NUM_FM1_10GEC 2 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 @@ -671,6 +694,7 @@ #define CONFIG_SYS_NUM_FMAN 1 #define CONFIG_SYS_NUM_FM1_DTSEC 5 #define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_PME_PLAT_CLK_DIV 2 #define CONFIG_SYS_PME_CLK CONFIG_PME_PLAT_CLK_DIV #define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0 diff --git a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h index 2cad6e285..99a72bc6e 100644 --- a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h +++ b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h @@ -78,6 +78,7 @@ typedef struct dimm_params_s { unsigned int trc_ps; /* maximum = 254 ns + .75 ns = 254750 ps */ unsigned int refresh_rate_ps; + unsigned int extended_op_srt; /* DDR3 doesn't need these as below */ unsigned int tis_ps; /* byte 32, spd->ca_setup */ diff --git a/arch/powerpc/include/asm/fsl_serdes.h b/arch/powerpc/include/asm/fsl_serdes.h index 1106d2805..cce892ce9 100644 --- a/arch/powerpc/include/asm/fsl_serdes.h +++ b/arch/powerpc/include/asm/fsl_serdes.h @@ -86,6 +86,7 @@ enum srds { int is_serdes_configured(enum srds_prtcl device); void fsl_serdes_init(void); +const char *serdes_clock_to_string(u32 clock); #ifdef CONFIG_FSL_CORENET #ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 diff --git a/arch/powerpc/include/asm/immap_512x.h b/arch/powerpc/include/asm/immap_512x.h index 814a53577..bed80aa93 100644 --- a/arch/powerpc/include/asm/immap_512x.h +++ b/arch/powerpc/include/asm/immap_512x.h @@ -1255,9 +1255,9 @@ static inline u32 get_pata_base (void) } #endif /* __ASSEMBLY__ */ -#define CONFIG_SYS_MPC512x_USB_OFFSET 0x4000 -#define CONFIG_SYS_MPC512x_USB_ADDR \ - (CONFIG_SYS_IMMR + CONFIG_SYS_MPC512x_USB_OFFSET) +#define CONFIG_SYS_MPC512x_USB1_OFFSET 0x4000 +#define CONFIG_SYS_MPC512x_USB1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC512x_USB1_OFFSET) #define IIM_BASE_ADDR (CONFIG_SYS_IMMR + offsetof(immap_t, iim)) diff --git a/arch/powerpc/include/asm/immap_83xx.h b/arch/powerpc/include/asm/immap_83xx.h index 57189c913..3c86ff66f 100644 --- a/arch/powerpc/include/asm/immap_83xx.h +++ b/arch/powerpc/include/asm/immap_83xx.h @@ -764,9 +764,11 @@ typedef struct immap { } immap_t; #ifdef CONFIG_HAS_FSL_MPH_USB -#define CONFIG_SYS_MPC83xx_USB_OFFSET 0x22000 /* use the MPH controller */ +#define CONFIG_SYS_MPC83xx_USB1_OFFSET 0x22000 /* use the MPH controller */ +#define CONFIG_SYS_MPC83xx_USB2_OFFSET 0 #else -#define CONFIG_SYS_MPC83xx_USB_OFFSET 0x23000 /* use the DR controller */ +#define CONFIG_SYS_MPC83xx_USB1_OFFSET 0 +#define CONFIG_SYS_MPC83xx_USB2_OFFSET 0x23000 /* use the DR controller */ #endif #elif defined(CONFIG_MPC8313) @@ -1031,11 +1033,15 @@ typedef struct immap { #define CONFIG_SYS_MPC83xx_ESDHC_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_ESDHC_OFFSET) -#ifndef CONFIG_SYS_MPC83xx_USB_OFFSET -#define CONFIG_SYS_MPC83xx_USB_OFFSET 0x23000 +#ifndef CONFIG_SYS_MPC83xx_USB1_OFFSET +#define CONFIG_SYS_MPC83xx_USB1_OFFSET 0x23000 +#endif +#define CONFIG_SYS_MPC83xx_USB1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB1_OFFSET) +#if defined(CONFIG_MPC834x) +#define CONFIG_SYS_MPC83xx_USB2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB2_OFFSET) #endif -#define CONFIG_SYS_MPC83xx_USB_ADDR \ - (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB_OFFSET) #define CONFIG_SYS_LBC_ADDR (&((immap_t *)CONFIG_SYS_IMMR)->im_lbc) #define CONFIG_SYS_TSEC1_OFFSET 0x24000 diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index e516e0731..060e0d769 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -2932,7 +2932,6 @@ struct ccsr_pman { #endif #define CONFIG_SYS_MPC85xx_USB1_OFFSET 0x210000 #define CONFIG_SYS_MPC85xx_USB2_OFFSET 0x211000 -#define CONFIG_SYS_MPC85xx_USB_OFFSET CONFIG_SYS_MPC85xx_USB1_OFFSET #define CONFIG_SYS_MPC85xx_USB1_PHY_OFFSET 0x214000 #define CONFIG_SYS_MPC85xx_USB2_PHY_OFFSET 0x214100 #define CONFIG_SYS_MPC85xx_SATA1_OFFSET 0x220000 @@ -2985,7 +2984,7 @@ struct ccsr_pman { #define CONFIG_SYS_MPC85xx_IFC_OFFSET 0x1e000 #define CONFIG_SYS_MPC85xx_L2_OFFSET 0x20000 #define CONFIG_SYS_MPC85xx_DMA_OFFSET 0x21000 -#define CONFIG_SYS_MPC85xx_USB_OFFSET 0x22000 +#define CONFIG_SYS_MPC85xx_USB1_OFFSET 0x22000 #define CONFIG_SYS_MPC85xx_USB2_OFFSET 0x23000 #ifdef CONFIG_TSECV2 #define CONFIG_SYS_TSEC1_OFFSET 0xB0000 @@ -3086,8 +3085,10 @@ struct ccsr_pman { (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_CORENET_SERDES_OFFSET) #define CONFIG_SYS_FSL_CORENET_SERDES2_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_CORENET_SERDES2_OFFSET) -#define CONFIG_SYS_MPC85xx_USB_ADDR \ - (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB_OFFSET) +#define CONFIG_SYS_MPC85xx_USB1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB1_OFFSET) +#define CONFIG_SYS_MPC85xx_USB2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB2_OFFSET) #define CONFIG_SYS_MPC85xx_USB1_PHY_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB1_PHY_OFFSET) #define CONFIG_SYS_MPC85xx_USB2_PHY_ADDR \ diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c index a101e0360..34bbfca55 100644 --- a/arch/powerpc/lib/board.c +++ b/arch/powerpc/lib/board.c @@ -984,7 +984,7 @@ void board_init_r(gd_t *id, ulong dest_addr) pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024; #endif #endif - sprintf(memsz, "%ldk", (bd->bi_memsize / 1024) - pram); + sprintf(memsz, "%ldk", (ulong) (bd->bi_memsize / 1024) - pram); setenv("mem", memsz); } #endif diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index f74651c52..f6b012dbb 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -457,22 +457,6 @@ static int serdes_refclock(u8 sw, u8 sdclk) return ret; } -static const char *serdes_clock_to_string(u32 clock) -{ - switch (clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - case SRDS_PLLCR0_RFCK_SEL_161_13: - return "161.13"; - default: - return "122.88"; - } -} - #define NUM_SRDS_BANKS 2 int misc_init_r(void) diff --git a/board/freescale/c29xpcie/ddr.c b/board/freescale/c29xpcie/ddr.c index 804ea1916..57a9b610e 100644 --- a/board/freescale/c29xpcie/ddr.c +++ b/board/freescale/c29xpcie/ddr.c @@ -9,6 +9,9 @@ #include <asm/fsl_ddr_sdram.h> #include <asm/fsl_ddr_dimm_params.h> +#include "cpld.h" + +#define C29XPCIE_HARDWARE_REVA 0x40 /* * Micron MT41J128M16HA-15E * */ @@ -61,7 +64,9 @@ void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, unsigned int ctrl_num) { + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); int i; + popts->clk_adjust = 4; popts->cpo_override = 0x1f; popts->write_data_delay = 4; @@ -79,6 +84,9 @@ void fsl_ddr_board_options(memctl_options_t *popts, popts->trwt_override = 1; popts->trwt = 0; + if (in_8(&cpld_data->hwver) == C29XPCIE_HARDWARE_REVA) + popts->ecc_mode = 0; + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c index 60e2100af..9212372fe 100644 --- a/board/freescale/corenet_ds/corenet_ds.c +++ b/board/freescale/corenet_ds/corenet_ds.c @@ -127,20 +127,6 @@ int board_early_init_r(void) return 0; } -static const char *serdes_clock_to_string(u32 clock) -{ - switch(clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - default: - return "150"; - } -} - #define NUM_SRDS_BANKS 3 int misc_init_r(void) diff --git a/board/freescale/p2041rdb/p2041rdb.c b/board/freescale/p2041rdb/p2041rdb.c index 60694a672..8554512df 100644 --- a/board/freescale/p2041rdb/p2041rdb.c +++ b/board/freescale/p2041rdb/p2041rdb.c @@ -155,20 +155,6 @@ unsigned long get_board_sys_clk(unsigned long dummy) } } -static const char *serdes_clock_to_string(u32 clock) -{ - switch (clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - default: - return "150"; - } -} - #define NUM_SRDS_BANKS 2 int misc_init_r(void) diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c index 5abb18a26..2aa176c7a 100644 --- a/board/freescale/t1040qds/t1040qds.c +++ b/board/freescale/t1040qds/t1040qds.c @@ -160,20 +160,6 @@ unsigned long get_board_ddr_clk(void) return 66666666; } -static const char *serdes_clock_to_string(u32 clock) -{ - switch (clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - default: - return "Unknown frequency"; - } -} - #define NUM_SRDS_BANKS 2 int misc_init_r(void) { diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c index 0c1a4fbd9..79b770b48 100644 --- a/board/freescale/t4qds/t4240qds.c +++ b/board/freescale/t4qds/t4240qds.c @@ -608,22 +608,6 @@ unsigned long get_board_ddr_clk(void) return 66666666; } -static const char *serdes_clock_to_string(u32 clock) -{ - switch (clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - case SRDS_PLLCR0_RFCK_SEL_161_13: - return "161.1328125"; - default: - return "???"; - } -} - int misc_init_r(void) { u8 sw; diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c index 136b2dee1..f941e44e8 100644 --- a/board/keymile/common/common.c +++ b/board/keymile/common/common.c @@ -24,10 +24,6 @@ #include "common.h" #include <i2c.h> -#if !defined(CONFIG_MPC83xx) -static void i2c_write_start_seq(void); -#endif - DECLARE_GLOBAL_DATA_PTR; /* @@ -78,7 +74,6 @@ int set_km_env(void) } #if defined(CONFIG_SYS_I2C_INIT_BOARD) -#if !defined(CONFIG_MPC83xx) static void i2c_write_start_seq(void) { set_sda(1); @@ -101,21 +96,6 @@ static void i2c_write_start_seq(void) */ int i2c_make_abort(void) { - -#if defined(CONFIG_HARD_I2C) && !defined(MACH_TYPE_KM_KIRKWOOD) - immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - - /* - * disable I2C controller first, otherwhise it thinks we want to - * talk to the slave port... - */ - clrbits_8(&i2c->i2c_i2mod, 0x01); - - /* Set the PortPins to GPIO */ - setports(1); -#endif - int scl_state = 0; int sda_state = 0; int i = 0; @@ -148,13 +128,8 @@ int i2c_make_abort(void) set_sda(1); get_sda(); -#if defined(CONFIG_HARD_I2C) - /* Set the PortPins back to use for I2C */ - setports(0); -#endif return ret; } -#endif /** * i2c_init_board - reset i2c bus. When the board is powercycled during a @@ -167,6 +142,7 @@ void i2c_init_board(void) } #endif +#if defined(CONFIG_KM_COMMON_ETH_INIT) int board_eth_init(bd_t *bis) { if (ethernet_present()) @@ -174,6 +150,7 @@ int board_eth_init(bd_t *bis) return -1; } +#endif /* * do_setboardid command diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile new file mode 100644 index 000000000..35d17ce9f --- /dev/null +++ b/board/keymile/kmp204x/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2001-2007 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)../common) +endif + +LIB = $(obj)lib$(BOARD).o + +COBJS := $(BOARD).o ddr.o eth.o tlb.o pci.o law.o \ + ../common/common.o ../common/ivm.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/keymile/kmp204x/ddr.c b/board/keymile/kmp204x/ddr.c new file mode 100644 index 000000000..bd425aab1 --- /dev/null +++ b/board/keymile/kmp204x/ddr.c @@ -0,0 +1,64 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * Copyright 2009-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + if (ctrl_num) { + printf("Wrong parameter for controller number %d", ctrl_num); + return; + } + + /* automatic calibration for nb of cycles between read and DQS pre */ + popts->cpo_override = 0xFF; + + /* 1/2 clk delay between wr command and data strobe */ + popts->write_data_delay = 4; + /* clk lauched 1/2 applied cylcle after address command */ + popts->clk_adjust = 4; + /* 1T timing: command/address held for only 1 cycle */ + popts->twot_en = 0; + + /* we have only one module, half str should be OK */ + popts->half_strength_driver_enable = 1; + + /* wrlvl values overriden as recommended by ddr init func */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x6; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = 0; + + puts("Initializing with SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + debug(" DDR: "); + return dram_size; +} diff --git a/board/keymile/kmp204x/eth.c b/board/keymile/kmp204x/eth.c new file mode 100644 index 000000000..a0731055a --- /dev/null +++ b/board/keymile/kmp204x/eth.c @@ -0,0 +1,71 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <netdev.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <phy.h> + +int board_eth_init(bd_t *bis) +{ + int ret = 0; +#ifdef CONFIG_FMAN_ENET + struct fsl_pq_mdio_info dtsec_mdio_info; + + printf("Initializing Fman\n"); + + dtsec_mdio_info.regs = + (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the real 1G MDIO bus */ + fsl_pq_mdio_init(bis, &dtsec_mdio_info); + + /* DTESC1/2 don't have a PHY, they are temporarily disabled + * so that u-boot doesn't try to unsuccessfuly enable them */ + fm_disable_port(FM1_DTSEC1); + fm_disable_port(FM1_DTSEC2); + + /* + * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf + * This is the debug interface, the only one used in u-boot + */ + fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + fm_info_set_mdio(FM1_DTSEC5, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + + ret = cpu_eth_init(bis); + + /* reenable DTSEC1/2 for later (kernel) */ + fm_enable_port(FM1_DTSEC1); + fm_enable_port(FM1_DTSEC2); +#endif + + return ret; +} + +#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL) + +#define mv88E1118_PAGE_REG 22 + +int board_phy_config(struct phy_device *phydev) +{ + if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) { + /* driver config is good */ + if (phydev->drv->config) + phydev->drv->config(phydev); + + /* but we still need to fix the LEDs */ + phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003); + phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840); + phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000); + } + + return 0; +} +#endif diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c new file mode 100644 index 000000000..f02642aec --- /dev/null +++ b/board/keymile/kmp204x/kmp204x.c @@ -0,0 +1,258 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * Copyright 2011,2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "../common/common.h" +#include "kmp204x.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME); + + return 0; +} + +/* TODO: implement the I2C deblocking function */ +int i2c_make_abort(void) +{ + return 1; +} + +#define ZL30158_RST 8 +#define ZL30343_RST 9 + +int board_early_init_f(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */ + setbits_be32(&gur->ddrclkdr, 0x001f000f); + + /* take the Zarlinks out of reset as soon as possible */ + qrio_prst(ZL30158_RST, false, false); + qrio_prst(ZL30343_RST, false, false); + + /* and set their reset to power-up only */ + qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST); + qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST); + + return 0; +} + +int board_early_init_r(void) +{ + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + set_liodns(); + setup_portals(); + + return 0; +} + +unsigned long get_board_sys_clk(unsigned long dummy) +{ + return 66666666; +} + +#define WDMASK_OFF 0x16 + +static void qrio_wdmask(u8 bit, bool wden) +{ + u16 wdmask; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + wdmask = in_be16(qrio_base + WDMASK_OFF); + + if (wden) + wdmask |= (1 << bit); + else + wdmask &= ~(1 << bit); + + out_be16(qrio_base + WDMASK_OFF, wdmask); +} + +#define PRST_OFF 0x1a + +void qrio_prst(u8 bit, bool en, bool wden) +{ + u16 prst; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + qrio_wdmask(bit, wden); + + prst = in_be16(qrio_base + PRST_OFF); + + if (en) + prst &= ~(1 << bit); + else + prst |= (1 << bit); + + out_be16(qrio_base + PRST_OFF, prst); +} + +#define PRSTCFG_OFF 0x1c + +void qrio_prstcfg(u8 bit, u8 mode) +{ + u32 prstcfg; + u8 i; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + prstcfg = in_be32(qrio_base + PRSTCFG_OFF); + + for (i = 0; i < 2; i++) { + if (mode & (1<<i)) + set_bit(2*bit+i, &prstcfg); + else + clear_bit(2*bit+i, &prstcfg); + } + + out_be32(qrio_base + PRSTCFG_OFF, prstcfg); +} + + +#define BOOTCOUNT_OFF 0x12 + +void bootcount_store(ulong counter) +{ + u8 val; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + val = (counter <= 255) ? (u8)counter : 255; + out_8(qrio_base + BOOTCOUNT_OFF, val); +} + +ulong bootcount_load(void) +{ + u8 val; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + val = in_8(qrio_base + BOOTCOUNT_OFF); + return val; +} + +#define NUM_SRDS_BANKS 2 +#define PHY_RST 15 + +int misc_init_r(void) +{ + serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100, + SRDS_PLLCR0_RFCK_SEL_125}; + unsigned int i; + + /* check SERDES reference clocks */ + for (i = 0; i < NUM_SRDS_BANKS; i++) { + u32 actual = in_be32(®s->bank[i].pllcr0); + actual &= SRDS_PLLCR0_RFCK_SEL_MASK; + if (actual != expected[i]) { + printf("Warning: SERDES bank %u expects reference \ + clock %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected[i]), + serdes_clock_to_string(actual)); + } + } + + /* take the mgmt eth phy out of reset */ + qrio_prst(PHY_RST, false, false); + + return 0; +} + +#if defined(CONFIG_HUSH_INIT_VAR) +int hush_init_var(void) +{ + ivm_read_eeprom(); + return 0; +} +#endif + +#if defined(CONFIG_LAST_STAGE_INIT) +int last_stage_init(void) +{ + set_km_env(); + return 0; +} +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN +void fdt_fixup_fman_mac_addresses(void *blob) +{ + int node, i, ret; + char *tmp, *end; + unsigned char mac_addr[6]; + + /* get the mac addr from env */ + tmp = getenv("ethaddr"); + if (!tmp) { + printf("ethaddr env variable not defined\n"); + return; + } + for (i = 0; i < 6; i++) { + mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0; + if (tmp) + tmp = (*end) ? end+1 : end; + } + + /* find the correct fdt ethernet path and correct it */ + node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000"); + if (node < 0) { + printf("no /soc/fman/ethernet path offset\n"); + return; + } + ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6); + if (ret) { + printf("error setting local-mac-address property\n"); + return; + } +} +#endif + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_fman_mac_addresses(blob); +#endif +} diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h new file mode 100644 index 000000000..b6ba67241 --- /dev/null +++ b/board/keymile/kmp204x/kmp204x.h @@ -0,0 +1,15 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#define PRSTCFG_POWUP_UNIT_CORE_RST 0x0 +#define PRSTCFG_POWUP_UNIT_RST 0x1 +#define PRSTCFG_POWUP_RST 0x3 + +void qrio_prst(u8 bit, bool en, bool wden); +void qrio_prstcfg(u8 bit, u8 mode); + +void pci_of_setup(void *blob, bd_t *bd); diff --git a/board/keymile/kmp204x/law.c b/board/keymile/kmp204x/law.c new file mode 100644 index 000000000..75d69e8b4 --- /dev/null +++ b/board/keymile/kmp204x/law.c @@ -0,0 +1,40 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + /* Limit DCSR to 32M to access NPC Trace Buffer */ + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC), +#endif + SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS + SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +#endif +#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS + SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg new file mode 100644 index 000000000..f38dcf9c8 --- /dev/null +++ b/board/keymile/kmp204x/pbi.cfg @@ -0,0 +1,35 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer docs/README.pblimage for more details about how-to configure +# and create PBL boot image +# + +#PBI commands +#Initialize CPC1 as 1MB SRAM +09010000 00200400 +09138000 00000000 +091380c0 00000100 +09010100 00000000 +09010104 fff0000b +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff00000 +09000d08 81000013 +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 27170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c new file mode 100644 index 000000000..ec20c8afb --- /dev/null +++ b/board/keymile/kmp204x/pci.c @@ -0,0 +1,35 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * Copyright 2007-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +#include "kmp204x.h" + +#define PCIE_SW_RST 14 +#define HOOPER_SW_RST 12 + +void pci_init_board(void) +{ + qrio_prst(PCIE_SW_RST, false, false); + qrio_prst(HOOPER_SW_RST, false, false); + /* Hooper is not direcly PCIe capable */ + mdelay(50); + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg new file mode 100644 index 000000000..f2b7fe3d4 --- /dev/null +++ b/board/keymile/kmp204x/rcw_kmp204x.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for kmp204x boards +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +14600000 00000000 28200000 00000000 +148E70CF CFC02000 58000000 41000000 +00000000 00000000 00000000 F4428002 +00000000 00000000 00000000 00000000 diff --git a/board/keymile/kmp204x/tlb.c b/board/keymile/kmp204x/tlb.c new file mode 100644 index 000000000..d03ca802a --- /dev/null +++ b/board/keymile/kmp204x/tlb.c @@ -0,0 +1,110 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + /* TLB 1 */ + /* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + /* QRIO */ + SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_64K, 1), + /* *I*G* - PCI1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_512M, 1), + /* *I*G* - PCI3 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_512M, 1), + /* *I*G* - PCI1&3 I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_128K, 1), +#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS + /* LBAPP1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256M, 1), +#endif +#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS + /* LBAPP2 */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_256M, 1), +#endif + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_32K, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 56af10246..5e101253f 100644 --- a/boards.cfg +++ b/boards.cfg @@ -43,6 +43,7 @@ # Status, Arch, CPU:SPLCPU, SoC, Vendor, Board name, Target, Options, Maintainers ########################################################################################################### +<<<<<<< HEAD Active arm arm1136 - armltd integrator integratorcp_cm1136 integratorcp:CM1136 Linus Walleij <linus.walleij@linaro.org> Active arm arm1136 mx31 - - imx31_phycore - - Active arm arm1136 mx31 davedenx - qong - Wolfgang Denk <wd@denx.de> @@ -966,6 +967,7 @@ Active powerpc mpc85xx - gdsys p1022 Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER_DEVELOP controlcenterd:TRAILBLAZER,SPIFLASH,DEVELOP Dirk Eibach <eibach@gdsys.de> +Active powerpc mpc85xx - keymile kmp204x kmlion1 kmp204x:KMLION1 Valentin Longchamp <valentin.longchamp@keymile.com> Active powerpc mpc85xx - stx stxgp3 stxgp3 - Dan Malek <dan@embeddedalley.com> Active powerpc mpc85xx - stx stxssa stxssa stxssa Dan Malek <dan@embeddedalley.com> Active powerpc mpc85xx - stx stxssa stxssa_4M stxssa:STXSSA_4M Dan Malek <dan@embeddedalley.com> @@ -1221,3 +1223,4 @@ Orphan powerpc mpc8xx - - genietv Orphan powerpc mpc8xx - - mbx8xx MBX - - Orphan powerpc mpc8xx - - mbx8xx MBX860T - - Orphan powerpc mpc8xx - - nx823 NX823 - - + diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 795209788..2f31fc96a 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -759,8 +759,12 @@ static int fsl_elbc_chip_init(int devnum, u8 *addr) nand->ecc.steps = 1; nand->ecc.strength = 1; } else { - /* otherwise fall back to default software ECC */ + /* otherwise fall back to software ECC */ +#if defined(CONFIG_NAND_ECC_BCH) + nand->ecc.mode = NAND_ECC_SOFT_BCH; +#else nand->ecc.mode = NAND_ECC_SOFT; +#endif } ret = nand_scan_ident(mtd, 1, NULL); diff --git a/drivers/net/fm/b4860.c b/drivers/net/fm/b4860.c index 9b3d5324e..373cc4f42 100644 --- a/drivers/net/fm/b4860.c +++ b/drivers/net/fm/b4860.c @@ -37,6 +37,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr2, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { if (is_device_disabled(port)) diff --git a/drivers/net/fm/fm.h b/drivers/net/fm/fm.h index 5f197a982..3ec49a4f3 100644 --- a/drivers/net/fm/fm.h +++ b/drivers/net/fm/fm.h @@ -99,6 +99,7 @@ int fm_init_common(int index, struct ccsr_fman *reg); int fm_eth_initialize(struct ccsr_fman *reg, struct fm_eth_info *info); phy_interface_t fman_port_enet_if(enum fm_port port); void fman_disable_port(enum fm_port port); +void fman_enable_port(enum fm_port port); struct fsl_enet_mac { void *base; /* MAC controller registers base address */ diff --git a/drivers/net/fm/init.c b/drivers/net/fm/init.c index 2d13145f1..35edd7ad9 100644 --- a/drivers/net/fm/init.c +++ b/drivers/net/fm/init.c @@ -145,6 +145,14 @@ void fm_disable_port(enum fm_port port) fman_disable_port(port); } +void fm_enable_port(enum fm_port port) +{ + int i = fm_port_to_index(port); + + fm_info[i].enabled = 1; + fman_enable_port(port); +} + void fm_info_set_mdio(enum fm_port port, struct mii_dev *bus) { int i = fm_port_to_index(port); diff --git a/drivers/net/fm/p1023.c b/drivers/net/fm/p1023.c index 0eaad0f45..b25d10ae0 100644 --- a/drivers/net/fm/p1023.c +++ b/drivers/net/fm/p1023.c @@ -34,6 +34,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/drivers/net/fm/p4080.c b/drivers/net/fm/p4080.c index febfdd4e8..de7191135 100644 --- a/drivers/net/fm/p4080.c +++ b/drivers/net/fm/p4080.c @@ -42,6 +42,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr2, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/drivers/net/fm/p5020.c b/drivers/net/fm/p5020.c index 8d49c7bc1..5c158cd5d 100644 --- a/drivers/net/fm/p5020.c +++ b/drivers/net/fm/p5020.c @@ -38,6 +38,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr2, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/drivers/net/fm/p5040.c b/drivers/net/fm/p5040.c index 546ebce56..403d7d794 100644 --- a/drivers/net/fm/p5040.c +++ b/drivers/net/fm/p5040.c @@ -44,6 +44,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr2, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/drivers/net/fm/t4240.c b/drivers/net/fm/t4240.c index 6253f22f7..1eacb2284 100644 --- a/drivers/net/fm/t4240.c +++ b/drivers/net/fm/t4240.c @@ -49,6 +49,13 @@ void fman_disable_port(enum fm_port port) setbits_be32(&gur->devdisr2, port_to_devdisr[port]); } +void fman_enable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + clrbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + phy_interface_t fman_port_enet_if(enum fm_port port) { ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 8f009191a..45e5d6a5b 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -38,7 +38,7 @@ static int usb_phy_clk_valid(struct usb_ehci *ehci) int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { - struct usb_ehci *ehci; + struct usb_ehci *ehci = NULL; const char *phy_type = NULL; size_t len; #ifdef CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -47,7 +47,18 @@ int ehci_hcd_init(int index, enum usb_init_type init, usb_phy[0] = '\0'; #endif - ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR; + switch (index) { + case 0: + ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR; + break; + case 1: + ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB2_ADDR; + break; + default: + printf("ERROR: wrong controller index!!\n"); + break; + }; + *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); *hcor = (struct ehci_hcor *)((uint32_t) *hccr + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); diff --git a/drivers/usb/host/ehci-mpc512x.c b/drivers/usb/host/ehci-mpc512x.c index a22109099..b320c4a4e 100644 --- a/drivers/usb/host/ehci-mpc512x.c +++ b/drivers/usb/host/ehci-mpc512x.c @@ -38,7 +38,7 @@ int ehci_hcd_init(int index, enum usb_init_type init, volatile struct usb_ehci *ehci; /* Hook the memory mapped registers for EHCI-Controller */ - ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR; + ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR; *hccr = (struct ehci_hccr *)((uint32_t)&(ehci->caplength)); *hcor = (struct ehci_hcor *)((uint32_t) *hccr + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); @@ -82,7 +82,7 @@ int ehci_hcd_stop(int index) int exit_status = 0; /* Reset the USB controller */ - ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR; + ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR; exit_status = reset_usb_controller(ehci); return exit_status; diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h index cce2288da..913e626b3 100644 --- a/include/configs/C29XPCIE.h +++ b/include/configs/C29XPCIE.h @@ -433,6 +433,8 @@ #define CONFIG_BAUDRATE 115200 +#define CONFIG_DEF_HWCONFIG fsl_ddr:ecc=on + #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=" __stringify(CONFIG_DEF_HWCONFIG) "\0" \ "netdev=eth0\0" \ diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h index 91ca480f4..f62fdf6bd 100644 --- a/include/configs/km/keymile-common.h +++ b/include/configs/km/keymile-common.h @@ -63,8 +63,6 @@ #define CONFIG_LOADS_ECHO #define CONFIG_SYS_LOADS_BAUD_CHANGE -#define CONFIG_SYS_I2C_INIT_BOARD - /* Support the IVM EEprom */ #define CONFIG_SYS_IVM_EEPROM_ADR 0x50 #define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400 @@ -80,8 +78,6 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME -#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) - /* UBI Support for all Keymile boards */ #define CONFIG_CMD_UBI #define CONFIG_RBTREE @@ -167,7 +163,7 @@ "add_default=" \ "setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off3" \ + ":${hostname}:${netdev}:off:" \ " console=" CONFIG_KM_CONSOLE_TTY ",${baudrate}" \ " mem=${kernelmem} init=${init}" \ CONFIG_KM_ECC_MODE \ diff --git a/include/configs/km/km-powerpc.h b/include/configs/km/km-powerpc.h index 8ee0ac6db..2cebb2bb0 100644 --- a/include/configs/km/km-powerpc.h +++ b/include/configs/km/km-powerpc.h @@ -17,6 +17,9 @@ #define CONFIG_CMD_DTT #define CONFIG_JFFS2_CMDLINE +/* standard km ethernet_present for piggy */ +#define CONFIG_KM_COMMON_ETH_INIT + /* EEprom support 24C08, 24C16, 24C64 */ #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE @@ -32,6 +35,9 @@ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +/* Reserve 4 MB for malloc */ +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + /****************************************************************************** * (PRAM usage) * ... ------------------------------------------------------- diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index e0368cb89..e74f85f60 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -54,6 +54,9 @@ #define CONFIG_ENV_SPI_MODE SPI_MODE_3 #endif +/* Reserve 4 MB for malloc */ +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + #include "asm/arch/config.h" #define CONFIG_SYS_TEXT_BASE 0x07d00000 /* code address before reloc */ @@ -161,6 +164,7 @@ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */ /* * UBI related stuff @@ -173,10 +177,9 @@ #undef CONFIG_I2C_MVTWSI #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_INIT_BOARD #define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */ -#if defined(CONFIG_SYS_I2C_SOFT) - #define CONFIG_SYS_NUM_I2C_BUSES 6 #define CONFIG_SYS_I2C_MAX_HOPS 1 #define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ @@ -211,7 +214,6 @@ int get_scl(void); #define CONFIG_SYS_I2C_SOFT_SLAVE 0x0 #define CONFIG_SYS_I2C_SOFT_SPEED 100000 -#endif /* EEprom support 24C128, 24C256 valid for environment eeprom */ #define CONFIG_SYS_I2C_MULTI_EEPROMS diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h new file mode 100644 index 000000000..2d5320b5c --- /dev/null +++ b/include/configs/km/kmp204x-common.h @@ -0,0 +1,450 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_KMP204X_H +#define _CONFIG_KMP204X_H + +#define CONFIG_PHYS_64BIT +#define CONFIG_PPC_P2041 + +#define CONFIG_SYS_TEXT_BASE 0xfff80000 + +#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" + +#define CONFIG_NAND_ECC_BCH + +/* common KM defines */ +#include "keymile-common.h" + +#define CONFIG_SYS_RAMBOOT +#define CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_SYS_DPAA_RMAN /* RMan */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +/* Environment in SPI Flash */ +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 20000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ +#define CONFIG_ENV_SIZE 0x004000 /* 16K env */ +#define CONFIG_ENV_SECT_SIZE 0x010000 +#define CONFIG_ENV_OFFSET_REDUND 0x110000 +#define CONFIG_ENV_TOTAL_SIZE 0x020000 + +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00800000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE +#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ + CONFIG_RAMBOOT_TEXT_BASE) +#define CONFIG_SYS_L3_SIZE (1024 << 10) +#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 + +/****************************************************************************** + * (PRAM usage) + * ... ------------------------------------------------------- + * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM + * ... |<------------------- pram -------------------------->| + * ... ------------------------------------------------------- + * @END_OF_RAM: + * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose + * @CONFIG_KM_PHRAM: address for /var + * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) + * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM + */ + +/* size of rootfs in RAM */ +#define CONFIG_KM_ROOTFSSIZE 0x0 +/* pseudo-non volatile RAM [hex] */ +#define CONFIG_KM_PNVRAM 0x80000 +/* physical RAM MTD size [hex] */ +#define CONFIG_KM_PHRAM 0x100000 +/* resereved pram area at the end of memroy [hex] */ +#define CONFIG_KM_RESERVED_PRAM 0x0 +/* enable protected RAM */ +#define CONFIG_PRAM 0 + +#define CONFIG_KM_CRAMFS_ADDR 0x2000000 +#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ +#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ + +#define CONFIG_BOOTCOUNT_LIMIT + +/* + * Local Bus Definitions + */ + +/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) + +/* Nand Flash */ +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull + +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#define CONFIG_BCH + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ + | OR_FCM_BCTLD /* LBCTL not ass */ \ + | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ + | OR_FCM_RST /* 1 clk read setup */ \ + | OR_FCM_PGS /* Large page size */ \ + | OR_FCM_CST) /* 0.25 command setup */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ + +/* QRIO FPGA */ +#define CONFIG_SYS_QRIO_BASE 0xfb000000 +#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull + +#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ + | OR_GPCM_BCTLD /* no LCTL assert */ \ + | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ + +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R +#define CONFIG_LAST_STAGE_INIT + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +#define CONFIG_KM_CONSOLE_TTY "ttyS0" + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ + } + +#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 10 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 10 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +/* Default address of microcode for the Linux Fman driver + * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) + * ucode is stored after env, so we got 0x120000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x120000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) + +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ + +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION + +/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_PHYLIB /* recommended PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC5" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * additionnal command line configuration. + */ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET + +/* we don't need flash support */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_FLASH_CFI_MTD +#undef CONFIG_JFFS2_CMDLINE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#define __USB_PHY_TYPE utmi + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV "km-common=empty\0" +#endif + +#ifndef MTDIDS_DEFAULT +# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" +#endif /* MTDIDS_DEFAULT */ + +#ifndef MTDPARTS_DEFAULT +# define MTDPARTS_DEFAULT "mtdparts=" \ + "fsl_elbc_nand:" \ + "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" +#endif /* MTDPARTS_DEFAULT */ + +/* architecture specific default bootargs */ +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" + +/* FIXME: FDT_ADDR is unspecified */ +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ + "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ + "update=" \ + "sf probe 0;sf erase 0 +${filesize};" \ + "sf write ${load_addr_r} 0 ${filesize};\0" \ + "" + +#define CONFIG_HW_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ + "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ + "usb_dr_mode=host\0" + +#define CONFIG_KM_NEW_ENV \ + "newenv=sf probe 0;" \ + "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ + __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" + +/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ +#ifndef CONFIG_KM_DEF_ARCH +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + CONFIG_KM_DEF_ARCH \ + CONFIG_KM_NEW_ENV \ + CONFIG_HW_ENV_SETTINGS \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#endif /* _CONFIG_KMP204X_H */ diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h index 986c65f1e..029c34828 100644 --- a/include/configs/km82xx.h +++ b/include/configs/km82xx.h @@ -227,6 +227,7 @@ /* enable I2C and select the hardware/software driver */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_INIT_BOARD #define CONFIG_SYS_NUM_I2C_BUSES 3 #define CONFIG_SYS_I2C_MAX_HOPS 1 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 @@ -237,6 +238,7 @@ {0, {{I2C_MUX_PCA9542, 0x70, 1} } } } #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_I2C_ABORT /* * Software (bit-bang) I2C driver configuration diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h new file mode 100644 index 000000000..4158c8dd0 --- /dev/null +++ b/include/configs/kmp204x.h @@ -0,0 +1,68 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* KMLION1 */ +#if defined(CONFIG_KMLION1) +#define CONFIG_HOSTNAME kmlion1 +#define CONFIG_KM_BOARD_NAME "kmlion1" + +#else +#error ("Board not supported") +#endif + +#define CONFIG_KMP204X + +#include "km/kmp204x-common.h" + +#if defined(CONFIG_KMLION1) +/* App1 Local bus */ +#define CONFIG_SYS_LBAPP1_BASE 0xD0000000 +#define CONFIG_SYS_LBAPP1_BASE_PHYS 0xFD0000000ull + +#define CONFIG_SYS_LBAPP1_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP1_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_LBAPP1_OR_PRELIM (OR_AM_256MB /* length 256MB */ \ + | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \ + | OR_GPCM_CSNT /* LCS 1/4 clk before */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ +/* Local bus app1 Base Address */ +#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_LBAPP1_BR_PRELIM +/* Local bus app1 Options */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_LBAPP1_OR_PRELIM + +/* App2 Local bus */ +#define CONFIG_SYS_LBAPP2_BASE 0xE0000000 +#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull + +#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \ + | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \ + | OR_GPCM_CSNT /* LCS 1/4 clk before */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ +/* Local bus app2 Base Address */ +#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM +/* Local bus app2 Options */ +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM +#endif + +#endif /* __CONFIG_H */ diff --git a/include/fm_eth.h b/include/fm_eth.h index 114bb8cf2..5a4fb70df 100644 --- a/include/fm_eth.h +++ b/include/fm_eth.h @@ -149,6 +149,7 @@ void fm_info_set_phy_address(enum fm_port port, int address); int fm_info_get_phy_address(enum fm_port port); void fm_info_set_mdio(enum fm_port port, struct mii_dev *bus); void fm_disable_port(enum fm_port port); +void fm_enable_port(enum fm_port port); void set_sgmii_phy(struct mii_dev *bus, enum fm_port base_port, unsigned int port_num, int phy_base_addr); int is_qsgmii_riser_card(struct mii_dev *bus, int phy_base_addr, diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h index 9e106fc42..734305b9d 100644 --- a/include/usb/ehci-fsl.h +++ b/include/usb/ehci-fsl.h @@ -149,11 +149,18 @@ #define MPC83XX_SCCR_USB_DRCM_10 0x00200000 #if defined(CONFIG_MPC83xx) -#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC83xx_USB_ADDR +#define CONFIG_SYS_FSL_USB1_ADDR CONFIG_SYS_MPC83xx_USB1_ADDR +#if defined(CONFIG_MPC834x) +#define CONFIG_SYS_FSL_USB2_ADDR CONFIG_SYS_MPC83xx_USB2_ADDR +#else +#define CONFIG_SYS_FSL_USB2_ADDR 0 +#endif #elif defined(CONFIG_MPC85xx) -#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC85xx_USB_ADDR +#define CONFIG_SYS_FSL_USB1_ADDR CONFIG_SYS_MPC85xx_USB1_ADDR +#define CONFIG_SYS_FSL_USB2_ADDR CONFIG_SYS_MPC85xx_USB2_ADDR #elif defined(CONFIG_MPC512X) -#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC512x_USB_ADDR +#define CONFIG_SYS_FSL_USB1_ADDR CONFIG_SYS_MPC512x_USB1_ADDR +#define CONFIG_SYS_FSL_USB2_ADDR 0 #endif /* |