diff options
79 files changed, 2053 insertions, 430 deletions
diff --git a/arch/arm/cpu/arm720t/tegra20/cpu.c b/arch/arm/cpu/arm720t/tegra20/cpu.c index 6d4d66bce..ddf8d979f 100644 --- a/arch/arm/cpu/arm720t/tegra20/cpu.c +++ b/arch/arm/cpu/arm720t/tegra20/cpu.c @@ -105,14 +105,14 @@ static void enable_cpu_clock(int enable) static int is_cpu_powered(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; return (readl(&pmc->pmc_pwrgate_status) & CPU_PWRED) ? 1 : 0; } static void remove_cpu_io_clamps(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; /* Remove the clamps on the CPU I/O signals */ @@ -126,7 +126,7 @@ static void remove_cpu_io_clamps(void) static void powerup_cpu(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; int timeout = IO_STABILIZATION_DELAY; @@ -157,7 +157,7 @@ static void powerup_cpu(void) static void enable_cpu_power_rail(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; reg = readl(&pmc->pmc_cntrl); diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c index b387ac27e..ecc26717c 100644 --- a/arch/arm/cpu/armv7/am33xx/board.c +++ b/arch/arm/cpu/armv7/am33xx/board.c @@ -37,7 +37,6 @@ DECLARE_GLOBAL_DATA_PTR; struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -struct gptimer *timer_base = (struct gptimer *)CONFIG_SYS_TIMERBASE; struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; static const struct gpio_bank gpio_bank_am33xx[4] = { @@ -119,22 +118,6 @@ static int read_eeprom(void) #define UART_SMART_IDLE_EN (0x1 << 0x3) #endif -#ifdef CONFIG_SPL_BUILD -/* Initialize timer */ -static void init_timer(void) -{ - /* Reset the Timer */ - writel(0x2, (&timer_base->tscir)); - - /* Wait until the reset is done */ - while (readl(&timer_base->tiocp_cfg) & 1) - ; - - /* Start the Timer */ - writel(0x1, (&timer_base->tclr)); -} -#endif - /* * Determine what type of DDR we have. */ @@ -183,9 +166,6 @@ void s_init(void) regVal |= UART_SMART_IDLE_EN; writel(regVal, &uart_base->uartsyscfg); - /* Initialize the Timer */ - init_timer(); - preloader_console_init(); /* Initalize the board header */ diff --git a/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c b/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c index 75cadb03e..925f8414c 100644 --- a/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c +++ b/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c @@ -46,7 +46,7 @@ static int do_enterrcm(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; puts("Entering RCM...\n"); udelay(50000); diff --git a/arch/arm/cpu/armv7/tegra20/usb.c b/arch/arm/cpu/armv7/tegra20/usb.c index 178bb130c..cac0918ff 100644 --- a/arch/arm/cpu/armv7/tegra20/usb.c +++ b/arch/arm/cpu/armv7/tegra20/usb.c @@ -137,24 +137,29 @@ static const u8 utmip_elastic_limit = 16; /* UTMIP High Speed Sync Start Delay */ static const u8 utmip_hs_sync_start_delay = 9; -/* Put the port into host mode (this only works for OTG ports) */ +/* Put the port into host mode */ static void set_host_mode(struct fdt_usb *config) { - if (config->dr_mode == DR_MODE_OTG) { - /* Check whether remote host from USB1 is driving VBus */ - if (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS) - return; + /* + * If we are an OTG port, check if remote host is driving VBus and + * bail out in this case. + */ + if (config->dr_mode == DR_MODE_OTG && + (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)) + return; - /* - * If not driving, we set the GPIO to enable VBUS. We assume - * that the pinmux is set up correctly for this. - */ - if (fdt_gpio_isvalid(&config->vbus_gpio)) { - fdtdec_setup_gpio(&config->vbus_gpio); - gpio_direction_output(config->vbus_gpio.gpio, 1); - debug("set_host_mode: GPIO %d high\n", - config->vbus_gpio.gpio); - } + /* + * If not driving, we set the GPIO to enable VBUS. We assume + * that the pinmux is set up correctly for this. + */ + if (fdt_gpio_isvalid(&config->vbus_gpio)) { + fdtdec_setup_gpio(&config->vbus_gpio); + gpio_direction_output(config->vbus_gpio.gpio, + (config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ? + 0 : 1); + debug("set_host_mode: GPIO %d %s\n", config->vbus_gpio.gpio, + (config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ? + "low" : "high"); } } diff --git a/arch/arm/cpu/tegra20-common/Makefile b/arch/arm/cpu/tegra20-common/Makefile index 43c96c686..9e91e5cb8 100644 --- a/arch/arm/cpu/tegra20-common/Makefile +++ b/arch/arm/cpu/tegra20-common/Makefile @@ -33,7 +33,7 @@ LIB = $(obj)lib$(SOC)-common.o SOBJS += lowlevel_init.o COBJS-y += ap20.o board.o clock.o funcmux.o pinmux.o sys_info.o timer.o -COBJS-$(CONFIG_TEGRA20_LP0) += warmboot.o crypto.o warmboot_avp.o +COBJS-$(CONFIG_TEGRA_LP0) += warmboot.o crypto.o warmboot_avp.o COBJS-$(CONFIG_TEGRA_CLOCK_SCALING) += emc.o COBJS-$(CONFIG_TEGRA_PMU) += pmu.o diff --git a/arch/arm/cpu/tegra20-common/ap20.c b/arch/arm/cpu/tegra20-common/ap20.c index 00588dae5..c0ca6eb37 100644 --- a/arch/arm/cpu/tegra20-common/ap20.c +++ b/arch/arm/cpu/tegra20-common/ap20.c @@ -32,7 +32,7 @@ int tegra_get_chip_type(void) { struct apb_misc_gp_ctlr *gp; - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; uint tegra_sku_id, rev; /* @@ -40,7 +40,7 @@ int tegra_get_chip_type(void) * APB_MISC + 0x804, and has value 0x20 for Tegra20, 0x30 for * Tegra30 */ - gp = (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + gp = (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; rev = (readl(&gp->hidrev) & HIDREV_CHIPID_MASK) >> HIDREV_CHIPID_SHIFT; tegra_sku_id = readl(&fuse->sku_info) & 0xff; @@ -101,7 +101,7 @@ static u32 get_odmdata(void) static void init_pmc_scratch(void) { - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 odmdata; int i; diff --git a/arch/arm/cpu/tegra20-common/board.c b/arch/arm/cpu/tegra20-common/board.c index 598023aba..8a8d3384a 100644 --- a/arch/arm/cpu/tegra20-common/board.c +++ b/arch/arm/cpu/tegra20-common/board.c @@ -47,7 +47,7 @@ enum { unsigned int query_sdram_size(void) { - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; reg = readl(&pmc->pmc_scratch20); @@ -81,11 +81,11 @@ int checkboard(void) #endif /* CONFIG_DISPLAY_BOARDINFO */ static int uart_configs[] = { -#if defined(CONFIG_TEGRA20_UARTA_UAA_UAB) +#if defined(CONFIG_TEGRA_UARTA_UAA_UAB) FUNCMUX_UART1_UAA_UAB, -#elif defined(CONFIG_TEGRA20_UARTA_GPU) +#elif defined(CONFIG_TEGRA_UARTA_GPU) FUNCMUX_UART1_GPU, -#elif defined(CONFIG_TEGRA20_UARTA_SDIO1) +#elif defined(CONFIG_TEGRA_UARTA_SDIO1) FUNCMUX_UART1_SDIO1, #else FUNCMUX_UART1_IRRX_IRTX, @@ -125,13 +125,13 @@ void board_init_uart_f(void) { int uart_ids = 0; /* bit mask of which UART ids to enable */ -#ifdef CONFIG_TEGRA20_ENABLE_UARTA +#ifdef CONFIG_TEGRA_ENABLE_UARTA uart_ids |= UARTA; #endif -#ifdef CONFIG_TEGRA20_ENABLE_UARTB +#ifdef CONFIG_TEGRA_ENABLE_UARTB uart_ids |= UARTB; #endif -#ifdef CONFIG_TEGRA20_ENABLE_UARTD +#ifdef CONFIG_TEGRA_ENABLE_UARTD uart_ids |= UARTD; #endif setup_uarts(uart_ids); diff --git a/arch/arm/cpu/tegra20-common/funcmux.c b/arch/arm/cpu/tegra20-common/funcmux.c index 8cfed645c..b2129adf2 100644 --- a/arch/arm/cpu/tegra20-common/funcmux.c +++ b/arch/arm/cpu/tegra20-common/funcmux.c @@ -234,6 +234,13 @@ int funcmux_select(enum periph_id id, int config) } break; + case PERIPH_ID_NDFLASH: + if (config == FUNCMUX_NDFLASH_ATC) { + pinmux_set_func(PINGRP_ATC, PMUX_FUNC_NAND); + pinmux_tristate_disable(PINGRP_ATC); + } + break; + default: debug("%s: invalid periph_id %d", __func__, id); return -1; diff --git a/arch/arm/cpu/tegra20-common/warmboot.c b/arch/arm/cpu/tegra20-common/warmboot.c index 809ea0133..6ce995ef0 100644 --- a/arch/arm/cpu/tegra20-common/warmboot.c +++ b/arch/arm/cpu/tegra20-common/warmboot.c @@ -39,7 +39,7 @@ DECLARE_GLOBAL_DATA_PTR; #ifndef CONFIG_TEGRA_CLOCK_SCALING -#error "You must enable CONFIG_TEGRA_CLOCK_SCALING to use CONFIG_TEGRA20_LP0" +#error "You must enable CONFIG_TEGRA_CLOCK_SCALING to use CONFIG_TEGRA_LP0" #endif /* @@ -139,9 +139,9 @@ int warmboot_save_sdram_params(void) u32 ram_code; struct sdram_params sdram; struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE; - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; struct emc_ctlr *emc = emc_get_controller(gd->fdt_blob); union scratch2_reg scratch2; union scratch4_reg scratch4; @@ -205,7 +205,7 @@ static u32 get_major_version(void) { u32 major_id; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; major_id = (readl(&gp->hidrev) & HIDREV_MAJORPREV_MASK) >> HIDREV_MAJORPREV_SHIFT; @@ -229,7 +229,7 @@ static int is_failure_analysis_mode(struct fuse_regs *fuse) static int ap20_is_odm_production_mode(void) { - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; if (!is_failure_analysis_mode(fuse) && is_odm_production_mode_fuse_set(fuse)) @@ -240,7 +240,7 @@ static int ap20_is_odm_production_mode(void) static int ap20_is_production_mode(void) { - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; if (get_major_version() == 0) return 1; @@ -257,7 +257,7 @@ static enum fuse_operating_mode fuse_get_operation_mode(void) { u32 chip_id; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; chip_id = (readl(&gp->hidrev) & HIDREV_CHIPID_MASK) >> HIDREV_CHIPID_SHIFT; diff --git a/arch/arm/cpu/tegra20-common/warmboot_avp.c b/arch/arm/cpu/tegra20-common/warmboot_avp.c index cd01908a4..80a5a15de 100644 --- a/arch/arm/cpu/tegra20-common/warmboot_avp.c +++ b/arch/arm/cpu/tegra20-common/warmboot_avp.c @@ -38,7 +38,7 @@ void wb_start(void) { struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE; - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; struct flow_ctlr *flow = (struct flow_ctlr *)NV_PA_FLOW_BASE; struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE; diff --git a/arch/arm/dts/tegra20.dtsi b/arch/arm/dts/tegra20.dtsi index f95be5813..d936b1e7e 100644 --- a/arch/arm/dts/tegra20.dtsi +++ b/arch/arm/dts/tegra20.dtsi @@ -204,4 +204,11 @@ compatible = "nvidia,tegra20-kbc"; reg = <0x7000e200 0x0078>; }; + + nand: nand-controller@70008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nvidia,tegra20-nand"; + reg = <0x70008000 0x100>; + }; }; diff --git a/arch/arm/include/asm/arch-omap3/dss.h b/arch/arm/include/asm/arch-omap3/dss.h index a830c43de..54add4b45 100644 --- a/arch/arm/include/asm/arch-omap3/dss.h +++ b/arch/arm/include/asm/arch-omap3/dss.h @@ -142,7 +142,6 @@ struct venc_regs { }; /* Few Register Offsets */ -#define FRAME_MODE_SHIFT 1 #define TFTSTN_SHIFT 3 #define DATALINES_SHIFT 8 @@ -182,6 +181,16 @@ struct panel_config { void *frame_buffer; }; +#define DSS_HBP(bp) (((bp) - 1) << 20) +#define DSS_HFP(fp) (((fp) - 1) << 8) +#define DSS_HSW(sw) ((sw) - 1) +#define DSS_VBP(bp) ((bp) << 20) +#define DSS_VFP(fp) ((fp) << 8) +#define DSS_VSW(sw) ((sw) - 1) + +#define PANEL_TIMING_H(bp, fp, sw) (DSS_HBP(bp) | DSS_HFP(fp) | DSS_HSW(sw)) +#define PANEL_TIMING_V(bp, fp, sw) (DSS_VBP(bp) | DSS_VFP(fp) | DSS_VSW(sw)) + /* Generic DSS Functions */ void omap3_dss_venc_config(const struct venc_regs *venc_cfg, u32 height, u32 width); diff --git a/arch/arm/include/asm/arch-omap3/mux.h b/arch/arm/include/asm/arch-omap3/mux.h index 71f183de8..6e92b23da 100644 --- a/arch/arm/include/asm/arch-omap3/mux.h +++ b/arch/arm/include/asm/arch-omap3/mux.h @@ -451,6 +451,11 @@ #define CONTROL_PADCONF_GPIO128 0x0A58 #define CONTROL_PADCONF_GPIO129 0x0A5A +/* AM/DM37xx specific: gpio_127, gpio_127 and gpio_129 require configuration + * of the extended drain cells */ +#define OMAP34XX_CTRL_WKUP_CTRL (OMAP34XX_CTRL_BASE + 0x0A5C) +#define OMAP34XX_CTRL_WKUP_CTRL_GPIO_IO_PWRDNZ (1<<6) + #define MUX_VAL(OFFSET,VALUE)\ writew((VALUE), OMAP34XX_CTRL_BASE + (OFFSET)); diff --git a/arch/arm/include/asm/arch-tegra20/ap20.h b/arch/arm/include/asm/arch-tegra20/ap20.h index c84d22f97..70d94c504 100644 --- a/arch/arm/include/asm/arch-tegra20/ap20.h +++ b/arch/arm/include/asm/arch-tegra20/ap20.h @@ -95,9 +95,6 @@ #define HALT_COP_EVENT_IRQ_1 (1 << 11) #define HALT_COP_EVENT_FIQ_1 (1 << 9) -/* Start up the tegra20 SOC */ -void tegra20_start(void); - /* This is the main entry into U-Boot, used by the Cortex-A9 */ extern void _start(void); diff --git a/arch/arm/include/asm/arch-tegra20/funcmux.h b/arch/arm/include/asm/arch-tegra20/funcmux.h index 258f7b641..bd511db85 100644 --- a/arch/arm/include/asm/arch-tegra20/funcmux.h +++ b/arch/arm/include/asm/arch-tegra20/funcmux.h @@ -57,6 +57,9 @@ enum { /* Serial Flash configs */ FUNCMUX_SPI1_GMC_GMD = 0, + + /* NAND flags */ + FUNCMUX_NDFLASH_ATC = 0, }; /** diff --git a/arch/arm/include/asm/arch-tegra20/mmc.h b/arch/arm/include/asm/arch-tegra20/mmc.h index 916a353a9..5c9504799 100644 --- a/arch/arm/include/asm/arch-tegra20/mmc.h +++ b/arch/arm/include/asm/arch-tegra20/mmc.h @@ -19,9 +19,9 @@ * MA 02111-1307 USA */ -#ifndef _TEGRA20_MMC_H_ -#define _TEGRA20_MMC_H_ +#ifndef _TEGRA_MMC_H_ +#define _TEGRA_MMC_H_ -int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio); +int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio); -#endif /* TEGRA20_MMC_H_ */ +#endif /* _TEGRA_MMC_H_ */ diff --git a/arch/arm/include/asm/arch-tegra20/sys_proto.h b/arch/arm/include/asm/arch-tegra20/sys_proto.h index 643d5424b..919aec7f7 100644 --- a/arch/arm/include/asm/arch-tegra20/sys_proto.h +++ b/arch/arm/include/asm/arch-tegra20/sys_proto.h @@ -24,12 +24,12 @@ #ifndef _SYS_PROTO_H_ #define _SYS_PROTO_H_ -struct tegra20_sysinfo { +struct tegra_sysinfo { char *board_string; }; void invalidate_dcache(void); -extern const struct tegra20_sysinfo sysinfo; +extern const struct tegra_sysinfo sysinfo; #endif diff --git a/arch/arm/include/asm/arch-tegra20/tegra20.h b/arch/arm/include/asm/arch-tegra20/tegra20.h index 6750754ba..c9485a1c8 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra20.h +++ b/arch/arm/include/asm/arch-tegra20/tegra20.h @@ -33,21 +33,22 @@ #define NV_PA_GPIO_BASE 0x6000D000 #define NV_PA_EVP_BASE 0x6000F000 #define NV_PA_APB_MISC_BASE 0x70000000 -#define TEGRA20_APB_MISC_GP_BASE (NV_PA_APB_MISC_BASE + 0x0800) +#define NV_PA_APB_MISC_GP_BASE (NV_PA_APB_MISC_BASE + 0x0800) #define NV_PA_APB_UARTA_BASE (NV_PA_APB_MISC_BASE + 0x6000) #define NV_PA_APB_UARTB_BASE (NV_PA_APB_MISC_BASE + 0x6040) #define NV_PA_APB_UARTC_BASE (NV_PA_APB_MISC_BASE + 0x6200) #define NV_PA_APB_UARTD_BASE (NV_PA_APB_MISC_BASE + 0x6300) #define NV_PA_APB_UARTE_BASE (NV_PA_APB_MISC_BASE + 0x6400) -#define TEGRA20_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) -#define TEGRA20_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) -#define TEGRA20_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) +#define NV_PA_NAND_BASE (NV_PA_APB_MISC_BASE + 0x8000) +#define NV_PA_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) +#define NV_PA_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) +#define NV_PA_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) #define NV_PA_CSITE_BASE 0x70040000 #define TEGRA_USB1_BASE 0xC5000000 #define TEGRA_USB3_BASE 0xC5008000 #define TEGRA_USB_ADDR_MASK 0xFFFFC000 -#define TEGRA20_SDRC_CS0 NV_PA_SDRAM_BASE +#define NV_PA_SDRC_CS0 NV_PA_SDRAM_BASE #define LOW_LEVEL_SRAM_STACK 0x4000FFFC #define EARLY_AVP_STACK (NV_PA_SDRAM_BASE + 0x20000) #define EARLY_CPU_STACK (EARLY_AVP_STACK - 4096) @@ -85,7 +86,7 @@ enum { }; #else /* __ASSEMBLY__ */ -#define PRM_RSTCTRL TEGRA20_PMC_BASE +#define PRM_RSTCTRL NV_PA_PMC_BASE #endif #endif /* TEGRA20_H */ diff --git a/drivers/mmc/tegra_mmc.h b/arch/arm/include/asm/arch-tegra20/tegra_mmc.h index b1f256419..dd746cae0 100644 --- a/drivers/mmc/tegra_mmc.h +++ b/arch/arm/include/asm/arch-tegra20/tegra_mmc.h @@ -22,13 +22,13 @@ #ifndef __TEGRA_MMC_H_ #define __TEGRA_MMC_H_ -#define TEGRA20_SDMMC1_BASE 0xC8000000 -#define TEGRA20_SDMMC2_BASE 0xC8000200 -#define TEGRA20_SDMMC3_BASE 0xC8000400 -#define TEGRA20_SDMMC4_BASE 0xC8000600 +#define TEGRA_SDMMC1_BASE 0xC8000000 +#define TEGRA_SDMMC2_BASE 0xC8000200 +#define TEGRA_SDMMC3_BASE 0xC8000400 +#define TEGRA_SDMMC4_BASE 0xC8000600 #ifndef __ASSEMBLY__ -struct tegra20_mmc { +struct tegra_mmc { unsigned int sysad; /* _SYSTEM_ADDRESS_0 */ unsigned short blksize; /* _BLOCK_SIZE_BLOCK_COUNT_0 15:00 */ unsigned short blkcnt; /* _BLOCK_SIZE_BLOCK_COUNT_0 31:16 */ @@ -118,7 +118,7 @@ struct tegra20_mmc { #define TEGRA_MMC_NORINTSIGEN_XFER_COMPLETE (1 << 1) struct mmc_host { - struct tegra20_mmc *reg; + struct tegra_mmc *reg; unsigned int version; /* SDHCI spec. version */ unsigned int clock; /* Current clock (MHz) */ unsigned int base; /* Base address, SDMMC1/2/3/4 */ diff --git a/arch/arm/include/asm/arch-tegra20/tegra_spi.h b/arch/arm/include/asm/arch-tegra20/tegra_spi.h index 8978beacc..d53a93ff5 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra_spi.h +++ b/arch/arm/include/asm/arch-tegra20/tegra_spi.h @@ -70,6 +70,6 @@ struct spi_tegra { #define SPI_STAT_CUR_BLKCNT (1 << 15) #define SPI_TIMEOUT 1000 -#define TEGRA20_SPI_MAX_FREQ 52000000 +#define TEGRA_SPI_MAX_FREQ 52000000 #endif /* _TEGRA_SPI_H_ */ diff --git a/arch/arm/include/asm/arch-tegra20/timer.h b/arch/arm/include/asm/arch-tegra20/timer.h index 43f7ab4ef..fdb99a73e 100644 --- a/arch/arm/include/asm/arch-tegra20/timer.h +++ b/arch/arm/include/asm/arch-tegra20/timer.h @@ -21,8 +21,8 @@ /* Tegra20 timer functions */ -#ifndef _TEGRA20_TIMER_H -#define _TEGRA20_TIMER_H +#ifndef _TEGRA_TIMER_H +#define _TEGRA_TIMER_H /* returns the current monotonic timer value in microseconds */ unsigned long timer_get_us(void); diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c index f1951e883..109a1ac75 100644 --- a/arch/arm/lib/board.c +++ b/arch/arm/lib/board.c @@ -241,6 +241,9 @@ init_fnc_t *init_sequence[] = { fdtdec_check_fdt, #endif timer_init, /* initialize timer */ +#ifdef CONFIG_BOARD_POSTCLK_INIT + board_postclk_init, +#endif #ifdef CONFIG_FSL_ESDHC get_clocks, #endif diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c index 776226fcb..e98244b5e 100644 --- a/board/BuS/eb_cpux9k2/cpux9k2.c +++ b/board/BuS/eb_cpux9k2/cpux9k2.c @@ -267,9 +267,9 @@ int drv_video_init(void) display_height = 256; printf("%ld x %ld pixel matrix\n", display_width, display_height); - /* RWH = 7 | RWS =7 | TDF = 15 | NWS = 0x7F */ - csr = AT91_SMC_CSR_RWHOLD(7) | AT91_SMC_CSR_RWSETUP(7) | - AT91_SMC_CSR_TDF(15) | AT91_SMC_CSR_NWS(127) | + /* RWH = 2 | RWS =2 | TDF = 4 | NWS = 0x6 */ + csr = AT91_SMC_CSR_RWHOLD(2) | AT91_SMC_CSR_RWSETUP(2) | + AT91_SMC_CSR_TDF(4) | AT91_SMC_CSR_NWS(6) | AT91_SMC_CSR_ACSS_STANDARD | AT91_SMC_CSR_DBW_16 | AT91_SMC_CSR_BAT_16 | AT91_SMC_CSR_WSEN; writel(csr, &mc->smc.csr[2]); diff --git a/board/avionic-design/common/tamonten.c b/board/avionic-design/common/tamonten.c index a0a4d1d07..93f12ea4f 100644 --- a/board/avionic-design/common/tamonten.c +++ b/board/avionic-design/common/tamonten.c @@ -78,7 +78,7 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0, SD slot, with 4-bit bus */ - tegra20_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); + tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); return 0; } diff --git a/board/avionic-design/dts/tegra20-tec.dts b/board/avionic-design/dts/tegra20-tec.dts index 9faebd8bc..bb3851b57 100644 --- a/board/avionic-design/dts/tegra20-tec.dts +++ b/board/avionic-design/dts/tegra20-tec.dts @@ -55,4 +55,15 @@ usb@c5004000 { status = "disabled"; }; + + nand-controller@70008000 { + nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */ + nvidia,width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; + }; }; diff --git a/board/compal/paz00/paz00.c b/board/compal/paz00/paz00.c index cd684f292..0f8f16701 100644 --- a/board/compal/paz00/paz00.c +++ b/board/compal/paz00/paz00.c @@ -70,11 +70,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init eMMC\n"); /* init dev 0, eMMC chip, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, -1, -1); + tegra_mmc_init(0, 4, -1, -1); debug("board_mmc_init: init SD slot\n"); /* init dev 3, SD slot, with 4-bit bus */ - tegra20_mmc_init(3, 4, GPIO_PV1, GPIO_PV5); + tegra_mmc_init(3, 4, GPIO_PV1, GPIO_PV5); return 0; } diff --git a/board/compulab/trimslice/trimslice.c b/board/compulab/trimslice/trimslice.c index 5dae15b96..893cca8c1 100644 --- a/board/compulab/trimslice/trimslice.c +++ b/board/compulab/trimslice/trimslice.c @@ -69,10 +69,10 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0 (SDMMC4), (micro-SD slot) with 4-bit bus */ - tegra20_mmc_init(0, 4, -1, GPIO_PP1); + tegra_mmc_init(0, 4, -1, GPIO_PP1); /* init dev 3 (SDMMC1), (SD slot) with 4-bit bus */ - tegra20_mmc_init(3, 4, -1, -1); + tegra_mmc_init(3, 4, -1, -1); return 0; } diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c index 7ab20408e..afe832a52 100644 --- a/board/nvidia/common/board.c +++ b/board/nvidia/common/board.c @@ -45,8 +45,8 @@ DECLARE_GLOBAL_DATA_PTR; -const struct tegra20_sysinfo sysinfo = { - CONFIG_TEGRA20_BOARD_STRING +const struct tegra_sysinfo sysinfo = { + CONFIG_TEGRA_BOARD_STRING }; #ifndef CONFIG_SPL_BUILD @@ -79,7 +79,7 @@ void pin_mux_spi(void) __attribute__((weak, alias("__pin_mux_spi"))); static void power_det_init(void) { #if defined(CONFIG_TEGRA20) - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; /* turn off power detects */ writel(0, &pmc->pmc_pwr_det_latch); @@ -132,7 +132,7 @@ int board_init(void) board_usb_init(gd->fdt_blob); #endif -#ifdef CONFIG_TEGRA20_LP0 +#ifdef CONFIG_TEGRA_LP0 /* save Sdram params to PMC 2, 4, and 24 for WB0 */ warmboot_save_sdram_params(); diff --git a/board/nvidia/dts/tegra20-harmony.dts b/board/nvidia/dts/tegra20-harmony.dts index c35195430..ca5facb7f 100644 --- a/board/nvidia/dts/tegra20-harmony.dts +++ b/board/nvidia/dts/tegra20-harmony.dts @@ -54,4 +54,14 @@ usb@c5004000 { status = "disabled"; }; + + nand-controller@70008000 { + nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */ + nvidia,width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; + }; }; diff --git a/board/nvidia/dts/tegra20-seaboard.dts b/board/nvidia/dts/tegra20-seaboard.dts index 335253953..25a63a05d 100644 --- a/board/nvidia/dts/tegra20-seaboard.dts +++ b/board/nvidia/dts/tegra20-seaboard.dts @@ -153,4 +153,14 @@ 0x1f04008a>; linux,fn-keymap = <0x05040002>; }; + + nand-controller@70008000 { + nvidia,wp-gpios = <&gpio 59 0>; /* PH3 */ + nvidia,width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; + }; }; diff --git a/board/nvidia/harmony/Makefile b/board/nvidia/harmony/Makefile index b6efa1c29..88b9dcf03 100644 --- a/board/nvidia/harmony/Makefile +++ b/board/nvidia/harmony/Makefile @@ -24,10 +24,6 @@ include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - LIB = $(obj)lib$(BOARD).o COBJS := $(BOARD).o diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c index 44977c78d..b4a811dc5 100644 --- a/board/nvidia/harmony/harmony.c +++ b/board/nvidia/harmony/harmony.c @@ -73,11 +73,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init SD slot J26\n"); /* init dev 0, SD slot J26, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); + tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); debug("board_mmc_init: init SD slot J5\n"); /* init dev 2, SD slot J5, with 4-bit bus */ - tegra20_mmc_init(2, 4, GPIO_PT3, GPIO_PI5); + tegra_mmc_init(2, 4, GPIO_PT3, GPIO_PI5); return 0; } diff --git a/board/nvidia/seaboard/Makefile b/board/nvidia/seaboard/Makefile index b6efa1c29..88b9dcf03 100644 --- a/board/nvidia/seaboard/Makefile +++ b/board/nvidia/seaboard/Makefile @@ -24,10 +24,6 @@ include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - LIB = $(obj)lib$(BOARD).o COBJS := $(BOARD).o diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c index 3298a6b3a..667f60a9b 100644 --- a/board/nvidia/seaboard/seaboard.c +++ b/board/nvidia/seaboard/seaboard.c @@ -81,11 +81,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init eMMC\n"); /* init dev 0, eMMC chip, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, -1, -1); + tegra_mmc_init(0, 4, -1, -1); debug("board_mmc_init: init SD slot\n"); /* init dev 1, SD slot, with 4-bit bus */ - tegra20_mmc_init(1, 4, GPIO_PI6, GPIO_PI5); + tegra_mmc_init(1, 4, GPIO_PI6, GPIO_PI5); return 0; } diff --git a/board/nvidia/ventana/Makefile b/board/nvidia/ventana/Makefile index e3b743553..147d0bcf9 100644 --- a/board/nvidia/ventana/Makefile +++ b/board/nvidia/ventana/Makefile @@ -24,9 +24,7 @@ include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common $(obj)../seaboard) -endif +$(shell mkdir -p $(obj)../seaboard) LIB = $(obj)lib$(BOARD).o diff --git a/board/nvidia/whistler/Makefile b/board/nvidia/whistler/Makefile index a910577f2..913f1cea4 100644 --- a/board/nvidia/whistler/Makefile +++ b/board/nvidia/whistler/Makefile @@ -24,10 +24,6 @@ include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - LIB = $(obj)lib$(BOARD).o COBJS := $(BOARD).o diff --git a/board/nvidia/whistler/whistler.c b/board/nvidia/whistler/whistler.c index c0a114d66..598b2e5ce 100644 --- a/board/nvidia/whistler/whistler.c +++ b/board/nvidia/whistler/whistler.c @@ -81,10 +81,10 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */ - tegra20_mmc_init(0, 8, -1, -1); + tegra_mmc_init(0, 8, -1, -1); /* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */ - tegra20_mmc_init(1, 8, -1, -1); + tegra_mmc_init(1, 8, -1, -1); return 0; } diff --git a/board/taskit/stamp9g20/stamp9g20.c b/board/taskit/stamp9g20/stamp9g20.c index 5e07bf8d4..06df0af06 100644 --- a/board/taskit/stamp9g20/stamp9g20.c +++ b/board/taskit/stamp9g20/stamp9g20.c @@ -159,15 +159,28 @@ int board_early_init_f(void) return 0; } -int board_init(void) +int board_postclk_init(void) { - /* Adress of boot parameters */ - gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + /* + * Initialize the serial interface here, because be need a running + * timer to set PC9 to high and wait for some time to enable the + * level converter of the RS232 interface on the PortuxG20 board. + */ - /* Enable the serial interface */ +#ifdef CONFIG_PORTUXG20 at91_set_gpio_output(AT91_PIN_PC9, 1); + mdelay(1); +#endif at91_seriald_hw_init(); + return 0; +} + +int board_init(void) +{ + /* Adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + stamp9G20_nand_hw_init(); #ifdef CONFIG_MACB stamp9G20_macb_hw_init(); diff --git a/board/technexion/twister/twister.c b/board/technexion/twister/twister.c index c2b10ac1e..7429e934f 100644 --- a/board/technexion/twister/twister.c +++ b/board/technexion/twister/twister.c @@ -100,8 +100,18 @@ int board_init(void) int misc_init_r(void) { + char *eth_addr; + dieid_num_r(); + eth_addr = getenv("ethaddr"); + if (eth_addr) + return 0; + +#ifndef CONFIG_SPL_BUILD + TAM3517_READ_MAC_FROM_EEPROM; +#endif + return 0; } diff --git a/board/teejet/mt_ventoux/mt_ventoux.c b/board/teejet/mt_ventoux/mt_ventoux.c index 9fbaedd79..b8ad4471f 100644 --- a/board/teejet/mt_ventoux/mt_ventoux.c +++ b/board/teejet/mt_ventoux/mt_ventoux.c @@ -21,13 +21,17 @@ #include <common.h> #include <netdev.h> +#include <malloc.h> #include <fpga.h> +#include <video_fb.h> #include <asm/io.h> #include <asm/arch/mem.h> #include <asm/arch/mux.h> #include <asm/arch/sys_proto.h> #include <asm/omap_gpio.h> #include <asm/arch/mmc_host_def.h> +#include <asm/arch/dss.h> +#include <asm/arch/clocks.h> #include <i2c.h> #include <spartan3.h> #include <asm/gpio.h> @@ -39,6 +43,9 @@ DECLARE_GLOBAL_DATA_PTR; +#define BUZZER 140 +#define SPEAKER 141 + #ifndef CONFIG_FPGA #error "The Teejet mt_ventoux must have CONFIG_FPGA enabled" #endif @@ -50,6 +57,42 @@ DECLARE_GLOBAL_DATA_PTR; #define FPGA_INIT 119 #define FPGA_DONE 154 +#define LCD_PWR 138 +#define LCD_PON_PIN 139 + +#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) +static struct { + u32 xres; + u32 yres; +} panel_resolution[] = { + { 480, 272 }, + { 800, 480 } +}; + +static struct panel_config lcd_cfg[] = { + { + .timing_h = PANEL_TIMING_H(4, 8, 41), + .timing_v = PANEL_TIMING_V(2, 4, 10), + .pol_freq = 0x00000000, /* Pol Freq */ + .divisor = 0x0001000d, /* 33Mhz Pixel Clock */ + .panel_type = 0x01, /* TFT */ + .data_lines = 0x03, /* 24 Bit RGB */ + .load_mode = 0x02, /* Frame Mode */ + .panel_color = 0, + }, + { + .timing_h = PANEL_TIMING_H(20, 192, 4), + .timing_v = PANEL_TIMING_V(2, 20, 10), + .pol_freq = 0x00004000, /* Pol Freq */ + .divisor = 0x0001000E, /* 36Mhz Pixel Clock */ + .panel_type = 0x01, /* TFT */ + .data_lines = 0x03, /* 24 Bit RGB */ + .load_mode = 0x02, /* Frame Mode */ + .panel_color = 0, + } +}; +#endif + /* Timing definitions for FPGA */ static const u32 gpmc_fpga[] = { FPGA_GPMC_CONFIG1, @@ -193,6 +236,33 @@ int board_init(void) mt_ventoux_init_fpga(); + /* GPIO_140: speaker #mute */ + MUX_VAL(CP(MCBSP3_DX), (IEN | PTU | EN | M4)) + /* GPIO_141: Buzz Hi */ + MUX_VAL(CP(MCBSP3_DR), (IEN | PTU | EN | M4)) + + /* Turning off the buzzer */ + gpio_request(BUZZER, "BUZZER_MUTE"); + gpio_request(SPEAKER, "SPEAKER"); + gpio_direction_output(BUZZER, 0); + gpio_direction_output(SPEAKER, 0); + + return 0; +} + +int misc_init_r(void) +{ + char *eth_addr; + + dieid_num_r(); + + eth_addr = getenv("ethaddr"); + if (eth_addr) + return 0; + +#ifndef CONFIG_SPL_BUILD + TAM3517_READ_MAC_FROM_EEPROM; +#endif return 0; } @@ -224,3 +294,46 @@ int board_mmc_init(bd_t *bis) return omap_mmc_init(0, 0, 0); } #endif + +#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) +int board_video_init(void) +{ + struct prcm *prcm_base = (struct prcm *)PRCM_BASE; + struct panel_config *panel = &lcd_cfg[0]; + char *s; + u32 index = 0; + + void *fb; + + fb = (void *)0x88000000; + + s = getenv("panel"); + if (s) { + index = simple_strtoul(s, NULL, 10); + if (index < ARRAY_SIZE(lcd_cfg)) + panel = &lcd_cfg[index]; + else + return 0; + } + + panel->frame_buffer = fb; + printf("Panel: %dx%d\n", panel_resolution[index].xres, + panel_resolution[index].yres); + panel->lcd_size = (panel_resolution[index].yres - 1) << 16 | + (panel_resolution[index].xres - 1); + + gpio_request(LCD_PWR, "LCD Power"); + gpio_request(LCD_PON_PIN, "LCD Pon"); + gpio_direction_output(LCD_PWR, 0); + gpio_direction_output(LCD_PON_PIN, 1); + + + setbits_le32(&prcm_base->fclken_dss, FCK_DSS_ON); + setbits_le32(&prcm_base->iclken_dss, ICK_DSS_ON); + + omap3_dss_panel_config(panel); + omap3_dss_enable(); + + return 0; +} +#endif diff --git a/board/teejet/mt_ventoux/mt_ventoux.h b/board/teejet/mt_ventoux/mt_ventoux.h index 9b2e43ec6..1cd7ec2ab 100644 --- a/board/teejet/mt_ventoux/mt_ventoux.h +++ b/board/teejet/mt_ventoux/mt_ventoux.h @@ -142,7 +142,8 @@ const omap3_sysinfo sysinfo = { /*GPIO_62: FPGA_RESET */ \ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M4)) \ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M4)) \ - MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/ \ + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) \ + /* GPIO_64*/ \ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M4)) \ /* DSS */\ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) \ @@ -174,26 +175,6 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) \ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) \ /* CAMERA */\ - MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) \ - MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) \ - MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) \ - MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\ - MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) \ - MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\ - MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) \ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) \ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) \ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) \ @@ -209,6 +190,7 @@ const omap3_sysinfo sysinfo = { /* GPIO_126: CardDetect */\ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M4)) \ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M4)) \ + /*GPIO_128 */ \ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M4)) \ \ MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M0)) /*MMC2_CLK*/\ @@ -221,7 +203,7 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(MMC2_DAT5), (IDIS | PTU | EN | M4)) \ MUX_VAL(CP(MMC2_DAT6), (IDIS | PTU | EN | M4)) \ /* GPIO_138: LCD_ENVD */\ - MUX_VAL(CP(MMC2_DAT7), (IDIS | PTU | EN | M4)) \ + MUX_VAL(CP(MMC2_DAT7), (IDIS | PTD | EN | M4)) \ /* GPIO_139: LCD_PON */\ /* McBSP */\ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \ @@ -241,16 +223,12 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(MCBSP2_DX), (IEN | PTD | EN | M4)) \ /* GPIO_119: FPGA_INIT */ \ \ - MUX_VAL(CP(MCBSP3_DX), (IEN | PTU | EN | M4)) \ - /* GPIO_140: speaker #mute */\ - MUX_VAL(CP(MCBSP3_DR), (IEN | PTU | EN | M4)) \ - /* GPIO_141: Buzz Hi */\ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTU | EN | M4)) \ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTU | EN | M4)) \ \ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M4)) \ /*GPIO_152: Ignition Sense */ \ - MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) \ + MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M4)) \ /*GPIO_153: Power Button Sense */ \ MUX_VAL(CP(MCBSP4_DX), (IEN | PTU | DIS | M4)) \ /* GPIO_154: FPGA_DONE */ \ @@ -264,10 +242,14 @@ const omap3_sysinfo sysinfo = { /* GPIO_150: USB status 1 */\ \ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) \ - MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) \ - MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) \ - MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M2)) \ + /* gpt9_pwm */\ + MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M2)) \ + /* gpt10_pwm */\ + MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M2)) \ + /* gpt8_pwm */\ + MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M2)) \ + /* gpt11_pwm */\ \ MUX_VAL(CP(UART3_CTS_RCTX), (IDIS | PTD | DIS | M4)) \ /*GPIO_163 : TS_PENIRQ*/ \ @@ -299,22 +281,24 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M4)) \ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) \ /* CCDC */\ - MUX_VAL(CP(CCDC_PCLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_PCLK), (IEN | PTU | EN | M4)) \ + /* GPIO94 */\ MUX_VAL(CP(CCDC_FIELD), (IEN | PTD | DIS | M4)) \ /* GPIO95: #Enable Output */\ - MUX_VAL(CP(CCDC_HD), (IEN | PTU | EN | M0)) \ - MUX_VAL(CP(CCDC_VD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_HD), (IEN | PTU | EN | M4)) \ + MUX_VAL(CP(CCDC_VD), (IEN | PTU | EN | M4)) \ MUX_VAL(CP(CCDC_WEN), (IEN | PTD | DIS | M4)) \ /* GPIO 99: #SOM_PWR_OFF */\ - MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | DIS | M4)) \ MUX_VAL(CP(CCDC_DATA1), (IEN | PTD | DIS | M4)) \ /* GPIO_100: #power out */\ - MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | DIS | M4)) \ + MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | DIS | M4)) \ + /* GPIO_102 */\ + MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | DIS | M4)) \ + MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | DIS | M4)) \ + MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | DIS | M4)) \ + MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | DIS | M4)) \ /* RMII */\ MUX_VAL(CP(RMII_MDIO_DATA), (IEN | M0)) \ MUX_VAL(CP(RMII_MDIO_CLK), (M0)) \ @@ -363,7 +347,8 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(SYS_BOOT8), (IEN | PTD | EN | M0)) \ \ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) \ - MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKOUT1), (IDIS | PTD | DIS | M4)) \ + /* gpio_10 */\ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) \ /* JTAG */\ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) \ @@ -387,12 +372,15 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | EN | M3)) \ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)) \ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)) \ - MUX_VAL(CP(ETK_D10_ES2), (IEN | PTU | EN | M4)) \ + MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | EN | M4)) \ + /* gpio_24 */\ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTD | DIS | M4)) \ - MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M3)) \ + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M4)) \ + /* gpio_26 */\ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)) \ - MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)) \ - MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M3)) \ + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M4)) \ + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M4)) \ + /* gpio_29 */\ /* Die to Die */\ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) \ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) \ diff --git a/boards.cfg b/boards.cfg index 72e780344..613d6b292 100644 --- a/boards.cfg +++ b/boards.cfg @@ -60,7 +60,8 @@ integratorcp_cm920t arm arm920t integrator armltd a320evb arm arm920t - faraday a320 at91rm9200ek arm arm920t at91rm9200ek atmel at91 at91rm9200ek at91rm9200ek_ram arm arm920t at91rm9200ek atmel at91 at91rm9200ek:RAMBOOT -eb_cpux9k2 arm arm920t - BuS at91 +eb_cpux9k2 arm arm920t eb_cpux9k2 BuS at91 eb_cpux9k2 +eb_cpux9k2_ram arm arm920t eb_cpux9k2 BuS at91 eb_cpux9k2:RAMBOOT cpuat91 arm arm920t cpuat91 eukrea at91 cpuat91 cpuat91_ram arm arm920t cpuat91 eukrea at91 cpuat91:RAMBOOT mx1ads arm arm920t - - imx diff --git a/common/cmd_nand.c b/common/cmd_nand.c index a91ccf4df..4367f5a0f 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -48,8 +48,8 @@ static int nand_dump(nand_info_t *nand, ulong off, int only_oob, int repeat) last = off; - datbuf = malloc(nand->writesize); - oobbuf = malloc(nand->oobsize); + datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize); + oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize); if (!datbuf || !oobbuf) { puts("No memory for page buffer\n"); return 1; diff --git a/common/env_mmc.c b/common/env_mmc.c index be2f2be20..a2ff90bf4 100644 --- a/common/env_mmc.c +++ b/common/env_mmc.c @@ -75,9 +75,28 @@ static int init_mmc_for_env(struct mmc *mmc) return -1; } +#ifdef CONFIG_SYS_MMC_ENV_PART + if (CONFIG_SYS_MMC_ENV_PART != mmc->part_num) { + if (mmc_switch_part(CONFIG_SYS_MMC_ENV_DEV, + CONFIG_SYS_MMC_ENV_PART)) { + puts("MMC partition switch failed\n"); + return -1; + } + } +#endif + return 0; } +static void fini_mmc_for_env(struct mmc *mmc) +{ +#ifdef CONFIG_SYS_MMC_ENV_PART + if (CONFIG_SYS_MMC_ENV_PART != mmc->part_num) + mmc_switch_part(CONFIG_SYS_MMC_ENV_DEV, + mmc->part_num); +#endif +} + #ifdef CONFIG_CMD_SAVEENV static inline int write_env(struct mmc *mmc, unsigned long size, unsigned long offset, const void *buffer) @@ -100,26 +119,38 @@ int saveenv(void) char *res; struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV); u32 offset; + int ret; - if (init_mmc_for_env(mmc) || mmc_get_env_addr(mmc, &offset)) + if (init_mmc_for_env(mmc)) return 1; + if (mmc_get_env_addr(mmc, &offset)) { + ret = 1; + goto fini; + } + res = (char *)&env_new->data; len = hexport_r(&env_htab, '\0', &res, ENV_SIZE, 0, NULL); if (len < 0) { error("Cannot export environment: errno = %d\n", errno); - return 1; + ret = 1; + goto fini; } env_new->crc = crc32(0, &env_new->data[0], ENV_SIZE); printf("Writing to MMC(%d)... ", CONFIG_SYS_MMC_ENV_DEV); if (write_env(mmc, CONFIG_ENV_SIZE, offset, (u_char *)env_new)) { puts("failed\n"); - return 1; + ret = 1; + goto fini; } puts("done\n"); - return 0; + ret = 0; + +fini: + fini_mmc_for_env(mmc); + return ret; } #endif /* CONFIG_CMD_SAVEENV */ @@ -143,13 +174,30 @@ void env_relocate_spec(void) ALLOC_CACHE_ALIGN_BUFFER(char, buf, CONFIG_ENV_SIZE); struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV); u32 offset; + int ret; - if (init_mmc_for_env(mmc) || mmc_get_env_addr(mmc, &offset)) - return set_default_env(NULL); + if (init_mmc_for_env(mmc)) { + ret = 1; + goto err; + } - if (read_env(mmc, CONFIG_ENV_SIZE, offset, buf)) - return set_default_env(NULL); + if (mmc_get_env_addr(mmc, &offset)) { + ret = 1; + goto fini; + } + + if (read_env(mmc, CONFIG_ENV_SIZE, offset, buf)) { + ret = 1; + goto fini; + } env_import(buf, 1); + ret = 0; + +fini: + fini_mmc_for_env(mmc); +err: + if (ret) + set_default_env(NULL); #endif } diff --git a/doc/device-tree-bindings/nand/nvidia,tegra20-nand.txt b/doc/device-tree-bindings/nand/nvidia,tegra20-nand.txt new file mode 100644 index 000000000..86ae4082d --- /dev/null +++ b/doc/device-tree-bindings/nand/nvidia,tegra20-nand.txt @@ -0,0 +1,53 @@ +NAND Flash +---------- + +(there isn't yet a generic binding in Linux, so this describes what is in +U-Boot. There should not be Linux-specific or U-Boot specific binding, just +a binding that describes this hardware. But agreeing a binding in Linux in +the absence of a driver may be beyond my powers.) + +The device node for a NAND flash device is as follows: + +Required properties : + - compatible : Should be "manufacturer,device", "nand-flash" + +This node should sit inside its controller. + + +Nvidia NAND Controller +---------------------- + +The device node for a NAND flash controller is as follows: + +Optional properties: + +nvidia,wp-gpios : GPIO of write-protect line, three cells in the format: + phandle, parameter, flags +nvidia,nand-width : bus width of the NAND device in bits + + - nvidia,nand-timing : Timing parameters for the NAND. Each is in ns. + Order is: MAX_TRP_TREA, TWB, Max(tCS, tCH, tALS, tALH), + TWHR, Max(tCS, tCH, tALS, tALH), TWH, TWP, TRH, TADL + + MAX_TRP_TREA is: + non-EDO mode: Max(tRP, tREA) + 6ns + EDO mode: tRP timing + +The 'reg' property should provide the chip select used by the flash chip. + + +Example +------- + +nand-controller@0x70008000 { + compatible = "nvidia,tegra20-nand"; + #address-cells = <1>; + #size-cells = <0>; + nvidia,wp-gpios = <&gpio 59 0>; /* PH3 */ + nvidia,nand-width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; +}; diff --git a/drivers/gpio/tegra_gpio.c b/drivers/gpio/tegra_gpio.c index 8cfcf8283..747f4cf92 100644 --- a/drivers/gpio/tegra_gpio.c +++ b/drivers/gpio/tegra_gpio.c @@ -34,10 +34,10 @@ #include <asm/gpio.h> enum { - TEGRA20_CMD_INFO, - TEGRA20_CMD_PORT, - TEGRA20_CMD_OUTPUT, - TEGRA20_CMD_INPUT, + TEGRA_CMD_INFO, + TEGRA_CMD_PORT, + TEGRA_CMD_OUTPUT, + TEGRA_CMD_INPUT, }; static struct gpio_names { diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c index b4eb49127..e3be14e3c 100644 --- a/drivers/i2c/tegra_i2c.c +++ b/drivers/i2c/tegra_i2c.c @@ -262,7 +262,7 @@ exit: return error; } -static int tegra20_i2c_write_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_write_data(u32 addr, u8 *data, u32 len) { int error; struct i2c_trans_info trans_info; @@ -275,12 +275,12 @@ static int tegra20_i2c_write_data(u32 addr, u8 *data, u32 len) error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); if (error) - debug("tegra20_i2c_write_data: Error (%d) !!!\n", error); + debug("tegra_i2c_write_data: Error (%d) !!!\n", error); return error; } -static int tegra20_i2c_read_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_read_data(u32 addr, u8 *data, u32 len) { int error; struct i2c_trans_info trans_info; @@ -293,7 +293,7 @@ static int tegra20_i2c_read_data(u32 addr, u8 *data, u32 len) error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); if (error) - debug("tegra20_i2c_read_data: Error (%d) !!!\n", error); + debug("tegra_i2c_read_data: Error (%d) !!!\n", error); return error; } @@ -438,7 +438,7 @@ int i2c_write_data(uchar chip, uchar *buffer, int len) debug("\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra20_i2c_write_data(chip << 1, buffer, len); + rc = tegra_i2c_write_data(chip << 1, buffer, len); if (rc) debug("i2c_write_data(): rc=%d\n", rc); @@ -452,7 +452,7 @@ int i2c_read_data(uchar chip, uchar *buffer, int len) debug("inside i2c_read_data():\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra20_i2c_read_data(chip << 1, buffer, len); + rc = tegra_i2c_read_data(chip << 1, buffer, len); if (rc) { debug("i2c_read_data(): rc=%d\n", rc); return rc; diff --git a/drivers/input/Makefile b/drivers/input/Makefile index 68c6a16bc..0805e8667 100644 --- a/drivers/input/Makefile +++ b/drivers/input/Makefile @@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)libinput.o COBJS-$(CONFIG_I8042_KBD) += i8042.o -COBJS-$(CONFIG_TEGRA20_KEYBOARD) += tegra-kbc.o +COBJS-$(CONFIG_TEGRA_KEYBOARD) += tegra-kbc.o ifdef CONFIG_PS2KBD COBJS-y += keyboard.o pc_keyb.o COBJS-$(CONFIG_PS2MULT) += ps2mult.o ps2ser.o diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index c1c286298..551d6a918 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -1162,7 +1162,8 @@ int mmc_startup(struct mmc *mmc) } /* store the partition info of emmc */ - if (ext_csd[EXT_CSD_PARTITIONING_SUPPORT] & PART_SUPPORT) + if ((ext_csd[EXT_CSD_PARTITIONING_SUPPORT] & PART_SUPPORT) || + ext_csd[EXT_CSD_BOOT_MULT]) mmc->part_config = ext_csd[EXT_CSD_PART_CONF]; } diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c index ddfa7279c..ca8fad865 100644 --- a/drivers/mmc/tegra_mmc.c +++ b/drivers/mmc/tegra_mmc.c @@ -25,7 +25,7 @@ #include <asm/io.h> #include <asm/arch/clk_rst.h> #include <asm/arch/clock.h> -#include "tegra_mmc.h" +#include <asm/arch/tegra_mmc.h> /* support 4 mmc hosts */ struct mmc mmc_dev[4]; @@ -39,31 +39,31 @@ struct mmc_host mmc_host[4]; * @param host Structure to fill in (base, reg, mmc_id) * @param dev_index Device index (0-3) */ -static void tegra20_get_setup(struct mmc_host *host, int dev_index) +static void tegra_get_setup(struct mmc_host *host, int dev_index) { - debug("tegra20_get_base_mmc: dev_index = %d\n", dev_index); + debug("tegra_get_setup: dev_index = %d\n", dev_index); switch (dev_index) { case 1: - host->base = TEGRA20_SDMMC3_BASE; + host->base = TEGRA_SDMMC3_BASE; host->mmc_id = PERIPH_ID_SDMMC3; break; case 2: - host->base = TEGRA20_SDMMC2_BASE; + host->base = TEGRA_SDMMC2_BASE; host->mmc_id = PERIPH_ID_SDMMC2; break; case 3: - host->base = TEGRA20_SDMMC1_BASE; + host->base = TEGRA_SDMMC1_BASE; host->mmc_id = PERIPH_ID_SDMMC1; break; case 0: default: - host->base = TEGRA20_SDMMC4_BASE; + host->base = TEGRA_SDMMC4_BASE; host->mmc_id = PERIPH_ID_SDMMC4; break; } - host->reg = (struct tegra20_mmc *)host->base; + host->reg = (struct tegra_mmc *)host->base; } static void mmc_prepare_data(struct mmc_host *host, struct mmc_data *data) @@ -345,7 +345,7 @@ static void mmc_change_clock(struct mmc_host *host, uint clock) debug(" mmc_change_clock called\n"); /* - * Change Tegra20 SDMMCx clock divisor here. Source is 216MHz, + * Change Tegra SDMMCx clock divisor here. Source is 216MHz, * PLLP_OUT0 */ if (clock == 0) @@ -494,11 +494,11 @@ static int mmc_core_init(struct mmc *mmc) return 0; } -int tegra20_mmc_getcd(struct mmc *mmc) +int tegra_mmc_getcd(struct mmc *mmc) { struct mmc_host *host = (struct mmc_host *)mmc->priv; - debug("tegra20_mmc_getcd called\n"); + debug("tegra_mmc_getcd called\n"); if (host->cd_gpio >= 0) return !gpio_get_value(host->cd_gpio); @@ -506,13 +506,13 @@ int tegra20_mmc_getcd(struct mmc *mmc) return 1; } -int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) +int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) { struct mmc_host *host; char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */ struct mmc *mmc; - debug(" tegra20_mmc_init: index %d, bus width %d " + debug(" tegra_mmc_init: index %d, bus width %d " "pwr_gpio %d cd_gpio %d\n", dev_index, bus_width, pwr_gpio, cd_gpio); @@ -521,7 +521,7 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) host->clock = 0; host->pwr_gpio = pwr_gpio; host->cd_gpio = cd_gpio; - tegra20_get_setup(host, dev_index); + tegra_get_setup(host, dev_index); clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000); @@ -539,12 +539,12 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) mmc = &mmc_dev[dev_index]; - sprintf(mmc->name, "Tegra20 SD/MMC"); + sprintf(mmc->name, "Tegra SD/MMC"); mmc->priv = host; mmc->send_cmd = mmc_send_cmd; mmc->set_ios = mmc_set_ios; mmc->init = mmc_core_init; - mmc->getcd = tegra20_mmc_getcd; + mmc->getcd = tegra_mmc_getcd; mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; if (bus_width == 8) @@ -559,7 +559,7 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) * max freq is highest HS eMMC clock as per the SD/MMC spec * (actually 52MHz) * Both of these are the closest equivalents w/216MHz source - * clock and Tegra20 SDMMC divisors. + * clock and Tegra SDMMC divisors. */ mmc->f_min = 375000; mmc->f_max = 48000000; diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 29dc20ef5..beb99cacb 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -62,6 +62,7 @@ COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o COBJS-$(CONFIG_NAND_SPEAR) += spr_nand.o +COBJS-$(CONFIG_TEGRA_NAND) += tegra_nand.o COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o COBJS-$(CONFIG_NAND_PLAT) += nand_plat.o endif diff --git a/drivers/mtd/nand/mxs_nand.c b/drivers/mtd/nand/mxs_nand.c index bf9414fef..4701be846 100644 --- a/drivers/mtd/nand/mxs_nand.c +++ b/drivers/mtd/nand/mxs_nand.c @@ -25,10 +25,10 @@ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ +#include <common.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/types.h> -#include <common.h> #include <malloc.h> #include <asm/errno.h> #include <asm/io.h> diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index bfd668fa0..891af1f2e 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2936,7 +2936,8 @@ int nand_scan_tail(struct mtd_info *mtd) struct nand_chip *chip = mtd->priv; if (!(chip->options & NAND_OWN_BUFFERS)) - chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL); + chip->buffers = memalign(ARCH_DMA_MINALIGN, + sizeof(*chip->buffers)); if (!chip->buffers) return -ENOMEM; diff --git a/drivers/mtd/nand/tegra_nand.c b/drivers/mtd/nand/tegra_nand.c new file mode 100644 index 000000000..8c1de3445 --- /dev/null +++ b/drivers/mtd/nand/tegra_nand.c @@ -0,0 +1,1026 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * (C) Copyright 2011 NVIDIA Corporation <www.nvidia.com> + * (C) Copyright 2006 Detlev Zundel, dzu@denx.de + * (C) Copyright 2006 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <nand.h> +#include <asm/arch/clk_rst.h> +#include <asm/arch/clock.h> +#include <asm/arch/funcmux.h> +#include <asm/arch/gpio.h> +#include <asm/errno.h> +#include <asm-generic/gpio.h> +#include <fdtdec.h> +#include "tegra_nand.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define NAND_CMD_TIMEOUT_MS 10 + +#define SKIPPED_SPARE_BYTES 4 + +/* ECC bytes to be generated for tag data */ +#define TAG_ECC_BYTES 4 + +/* 64 byte oob block info for large page (== 2KB) device + * + * OOB flash layout for Tegra with Reed-Solomon 4 symbol correct ECC: + * Skipped bytes(4) + * Main area Ecc(36) + * Tag data(20) + * Tag data Ecc(4) + * + * Yaffs2 will use 16 tag bytes. + */ +static struct nand_ecclayout eccoob = { + .eccbytes = 36, + .eccpos = { + 4, 5, 6, 7, 8, 9, 10, 11, 12, + 13, 14, 15, 16, 17, 18, 19, 20, 21, + 22, 23, 24, 25, 26, 27, 28, 29, 30, + 31, 32, 33, 34, 35, 36, 37, 38, 39, + }, + .oobavail = 20, + .oobfree = { + { + .offset = 40, + .length = 20, + }, + } +}; + +enum { + ECC_OK, + ECC_TAG_ERROR = 1 << 0, + ECC_DATA_ERROR = 1 << 1 +}; + +/* Timing parameters */ +enum { + FDT_NAND_MAX_TRP_TREA, + FDT_NAND_TWB, + FDT_NAND_MAX_TCR_TAR_TRR, + FDT_NAND_TWHR, + FDT_NAND_MAX_TCS_TCH_TALS_TALH, + FDT_NAND_TWH, + FDT_NAND_TWP, + FDT_NAND_TRH, + FDT_NAND_TADL, + + FDT_NAND_TIMING_COUNT +}; + +/* Information about an attached NAND chip */ +struct fdt_nand { + struct nand_ctlr *reg; + int enabled; /* 1 to enable, 0 to disable */ + struct fdt_gpio_state wp_gpio; /* write-protect GPIO */ + s32 width; /* bit width, normally 8 */ + u32 timing[FDT_NAND_TIMING_COUNT]; +}; + +struct nand_drv { + struct nand_ctlr *reg; + + /* + * When running in PIO mode to get READ ID bytes from register + * RESP_0, we need this variable as an index to know which byte in + * register RESP_0 should be read. + * Because common code in nand_base.c invokes read_byte function two + * times for NAND_CMD_READID. + * And our controller returns 4 bytes at once in register RESP_0. + */ + int pio_byte_index; + struct fdt_nand config; +}; + +static struct nand_drv nand_ctrl; +static struct mtd_info *our_mtd; +static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; + +#ifdef CONFIG_SYS_DCACHE_OFF +static inline void dma_prepare(void *start, unsigned long length, + int is_writing) +{ +} +#else +/** + * Prepare for a DMA transaction + * + * For a write we flush out our data. For a read we invalidate, since we + * need to do this before we read from the buffer after the DMA has + * completed, so may as well do it now. + * + * @param start Start address for DMA buffer (should be cache-aligned) + * @param length Length of DMA buffer in bytes + * @param is_writing 0 if reading, non-zero if writing + */ +static void dma_prepare(void *start, unsigned long length, int is_writing) +{ + unsigned long addr = (unsigned long)start; + + length = ALIGN(length, ARCH_DMA_MINALIGN); + if (is_writing) + flush_dcache_range(addr, addr + length); + else + invalidate_dcache_range(addr, addr + length); +} +#endif + +/** + * Wait for command completion + * + * @param reg nand_ctlr structure + * @return + * 1 - Command completed + * 0 - Timeout + */ +static int nand_waitfor_cmd_completion(struct nand_ctlr *reg) +{ + u32 reg_val; + int running; + int i; + + for (i = 0; i < NAND_CMD_TIMEOUT_MS * 1000; i++) { + if ((readl(®->command) & CMD_GO) || + !(readl(®->status) & STATUS_RBSY0) || + !(readl(®->isr) & ISR_IS_CMD_DONE)) { + udelay(1); + continue; + } + reg_val = readl(®->dma_mst_ctrl); + /* + * If DMA_MST_CTRL_EN_A_ENABLE or DMA_MST_CTRL_EN_B_ENABLE + * is set, that means DMA engine is running. + * + * Then we have to wait until DMA_MST_CTRL_IS_DMA_DONE + * is cleared, indicating DMA transfer completion. + */ + running = reg_val & (DMA_MST_CTRL_EN_A_ENABLE | + DMA_MST_CTRL_EN_B_ENABLE); + if (!running || (reg_val & DMA_MST_CTRL_IS_DMA_DONE)) + return 1; + udelay(1); + } + return 0; +} + +/** + * Read one byte from the chip + * + * @param mtd MTD device structure + * @return data byte + * + * Read function for 8bit bus-width + */ +static uint8_t read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + u32 dword_read; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + /* In PIO mode, only 4 bytes can be transferred with single CMD_GO. */ + if (info->pio_byte_index > 3) { + info->pio_byte_index = 0; + writel(CMD_GO | CMD_PIO + | CMD_RX | CMD_CE0, + &info->reg->command); + if (!nand_waitfor_cmd_completion(info->reg)) + printf("Command timeout\n"); + } + + dword_read = readl(&info->reg->resp); + dword_read = dword_read >> (8 * info->pio_byte_index); + info->pio_byte_index++; + return (uint8_t)dword_read; +} + +/** + * Check NAND status to see if it is ready or not + * + * @param mtd MTD device structure + * @return + * 1 - ready + * 0 - not ready + */ +static int nand_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + int reg_val; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + reg_val = readl(&info->reg->status); + if (reg_val & STATUS_RBSY0) + return 1; + else + return 0; +} + +/* Dummy implementation: we don't support multiple chips */ +static void nand_select_chip(struct mtd_info *mtd, int chipnr) +{ + switch (chipnr) { + case -1: + case 0: + break; + + default: + BUG(); + } +} + +/** + * Clear all interrupt status bits + * + * @param reg nand_ctlr structure + */ +static void nand_clear_interrupt_status(struct nand_ctlr *reg) +{ + u32 reg_val; + + /* Clear interrupt status */ + reg_val = readl(®->isr); + writel(reg_val, ®->isr); +} + +/** + * Send command to NAND device + * + * @param mtd MTD device structure + * @param command the command to be sent + * @param column the column address for this command, -1 if none + * @param page_addr the page address for this command, -1 if none + */ +static void nand_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + /* + * Write out the command to the device. + * + * Only command NAND_CMD_RESET or NAND_CMD_READID will come + * here before mtd->writesize is initialized. + */ + + /* Emulate NAND_CMD_READOOB */ + if (command == NAND_CMD_READOOB) { + assert(mtd->writesize != 0); + column += mtd->writesize; + command = NAND_CMD_READ0; + } + + /* Adjust columns for 16 bit bus-width */ + if (column != -1 && (chip->options & NAND_BUSWIDTH_16)) + column >>= 1; + + nand_clear_interrupt_status(info->reg); + + /* Stop DMA engine, clear DMA completion status */ + writel(DMA_MST_CTRL_EN_A_DISABLE + | DMA_MST_CTRL_EN_B_DISABLE + | DMA_MST_CTRL_IS_DMA_DONE, + &info->reg->dma_mst_ctrl); + + /* + * Program and erase have their own busy handlers + * status and sequential in needs no delay + */ + switch (command) { + case NAND_CMD_READID: + writel(NAND_CMD_READID, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_ALE | CMD_PIO + | CMD_RX | + ((4 - 1) << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0, + &info->reg->command); + info->pio_byte_index = 0; + break; + case NAND_CMD_READ0: + writel(NAND_CMD_READ0, &info->reg->cmd_reg1); + writel(NAND_CMD_READSTART, &info->reg->cmd_reg2); + writel((page_addr << 16) | (column & 0xFFFF), + &info->reg->addr_reg1); + writel(page_addr >> 16, &info->reg->addr_reg2); + return; + case NAND_CMD_SEQIN: + writel(NAND_CMD_SEQIN, &info->reg->cmd_reg1); + writel(NAND_CMD_PAGEPROG, &info->reg->cmd_reg2); + writel((page_addr << 16) | (column & 0xFFFF), + &info->reg->addr_reg1); + writel(page_addr >> 16, + &info->reg->addr_reg2); + return; + case NAND_CMD_PAGEPROG: + return; + case NAND_CMD_ERASE1: + writel(NAND_CMD_ERASE1, &info->reg->cmd_reg1); + writel(NAND_CMD_ERASE2, &info->reg->cmd_reg2); + writel(page_addr, &info->reg->addr_reg1); + writel(CMD_GO | CMD_CLE | CMD_ALE | + CMD_SEC_CMD | CMD_CE0 | CMD_ALE_BYTES3, + &info->reg->command); + break; + case NAND_CMD_ERASE2: + return; + case NAND_CMD_STATUS: + writel(NAND_CMD_STATUS, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_PIO | CMD_RX + | ((1 - 0) << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0, + &info->reg->command); + info->pio_byte_index = 0; + break; + case NAND_CMD_RESET: + writel(NAND_CMD_RESET, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_CE0, + &info->reg->command); + break; + case NAND_CMD_RNDOUT: + default: + printf("%s: Unsupported command %d\n", __func__, command); + return; + } + if (!nand_waitfor_cmd_completion(info->reg)) + printf("Command 0x%02X timeout\n", command); +} + +/** + * Check whether the pointed buffer are all 0xff (blank). + * + * @param buf data buffer for blank check + * @param len length of the buffer in byte + * @return + * 1 - blank + * 0 - non-blank + */ +static int blank_check(u8 *buf, int len) +{ + int i; + + for (i = 0; i < len; i++) + if (buf[i] != 0xFF) + return 0; + return 1; +} + +/** + * After a DMA transfer for read, we call this function to see whether there + * is any uncorrectable error on the pointed data buffer or oob buffer. + * + * @param reg nand_ctlr structure + * @param databuf data buffer + * @param a_len data buffer length + * @param oobbuf oob buffer + * @param b_len oob buffer length + * @return + * ECC_OK - no ECC error or correctable ECC error + * ECC_TAG_ERROR - uncorrectable tag ECC error + * ECC_DATA_ERROR - uncorrectable data ECC error + * ECC_DATA_ERROR + ECC_TAG_ERROR - uncorrectable data+tag ECC error + */ +static int check_ecc_error(struct nand_ctlr *reg, u8 *databuf, + int a_len, u8 *oobbuf, int b_len) +{ + int return_val = ECC_OK; + u32 reg_val; + + if (!(readl(®->isr) & ISR_IS_ECC_ERR)) + return ECC_OK; + + /* + * Area A is used for the data block (databuf). Area B is used for + * the spare block (oobbuf) + */ + reg_val = readl(®->dec_status); + if ((reg_val & DEC_STATUS_A_ECC_FAIL) && databuf) { + reg_val = readl(®->bch_dec_status_buf); + /* + * If uncorrectable error occurs on data area, then see whether + * they are all FF. If all are FF, it's a blank page. + * Not error. + */ + if ((reg_val & BCH_DEC_STATUS_FAIL_SEC_FLAG_MASK) && + !blank_check(databuf, a_len)) + return_val |= ECC_DATA_ERROR; + } + + if ((reg_val & DEC_STATUS_B_ECC_FAIL) && oobbuf) { + reg_val = readl(®->bch_dec_status_buf); + /* + * If uncorrectable error occurs on tag area, then see whether + * they are all FF. If all are FF, it's a blank page. + * Not error. + */ + if ((reg_val & BCH_DEC_STATUS_FAIL_TAG_MASK) && + !blank_check(oobbuf, b_len)) + return_val |= ECC_TAG_ERROR; + } + + return return_val; +} + +/** + * Set GO bit to send command to device + * + * @param reg nand_ctlr structure + */ +static void start_command(struct nand_ctlr *reg) +{ + u32 reg_val; + + reg_val = readl(®->command); + reg_val |= CMD_GO; + writel(reg_val, ®->command); +} + +/** + * Clear command GO bit, DMA GO bit, and DMA completion status + * + * @param reg nand_ctlr structure + */ +static void stop_command(struct nand_ctlr *reg) +{ + /* Stop command */ + writel(0, ®->command); + + /* Stop DMA engine and clear DMA completion status */ + writel(DMA_MST_CTRL_GO_DISABLE + | DMA_MST_CTRL_IS_DMA_DONE, + ®->dma_mst_ctrl); +} + +/** + * Set up NAND bus width and page size + * + * @param info nand_info structure + * @param *reg_val address of reg_val + * @return 0 if ok, -1 on error + */ +static int set_bus_width_page_size(struct fdt_nand *config, + u32 *reg_val) +{ + if (config->width == 8) + *reg_val = CFG_BUS_WIDTH_8BIT; + else if (config->width == 16) + *reg_val = CFG_BUS_WIDTH_16BIT; + else { + debug("%s: Unsupported bus width %d\n", __func__, + config->width); + return -1; + } + + if (our_mtd->writesize == 512) + *reg_val |= CFG_PAGE_SIZE_512; + else if (our_mtd->writesize == 2048) + *reg_val |= CFG_PAGE_SIZE_2048; + else if (our_mtd->writesize == 4096) + *reg_val |= CFG_PAGE_SIZE_4096; + else { + debug("%s: Unsupported page size %d\n", __func__, + our_mtd->writesize); + return -1; + } + + return 0; +} + +/** + * Page read/write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + * @param page page number + * @param with_ecc 1 to enable ECC, 0 to disable ECC + * @param is_writing 0 for read, 1 for write + * @return 0 when successfully completed + * -EIO when command timeout + */ +static int nand_rw_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int page, int with_ecc, int is_writing) +{ + u32 reg_val; + int tag_size; + struct nand_oobfree *free = chip->ecc.layout->oobfree; + /* 4*128=512 (byte) is the value that our HW can support. */ + ALLOC_CACHE_ALIGN_BUFFER(u32, tag_buf, 128); + char *tag_ptr; + struct nand_drv *info; + struct fdt_nand *config; + + if ((uintptr_t)buf & 0x03) { + printf("buf %p has to be 4-byte aligned\n", buf); + return -EINVAL; + } + + info = (struct nand_drv *)chip->priv; + config = &info->config; + if (set_bus_width_page_size(config, ®_val)) + return -EINVAL; + + /* Need to be 4-byte aligned */ + tag_ptr = (char *)tag_buf; + + stop_command(info->reg); + + writel((1 << chip->page_shift) - 1, &info->reg->dma_cfg_a); + writel(virt_to_phys(buf), &info->reg->data_block_ptr); + + if (with_ecc) { + writel(virt_to_phys(tag_ptr), &info->reg->tag_ptr); + if (is_writing) + memcpy(tag_ptr, chip->oob_poi + free->offset, + chip->ecc.layout->oobavail + + TAG_ECC_BYTES); + } else { + writel(virt_to_phys(chip->oob_poi), &info->reg->tag_ptr); + } + + /* Set ECC selection, configure ECC settings */ + if (with_ecc) { + tag_size = chip->ecc.layout->oobavail + TAG_ECC_BYTES; + reg_val |= (CFG_SKIP_SPARE_SEL_4 + | CFG_SKIP_SPARE_ENABLE + | CFG_HW_ECC_CORRECTION_ENABLE + | CFG_ECC_EN_TAG_DISABLE + | CFG_HW_ECC_SEL_RS + | CFG_HW_ECC_ENABLE + | CFG_TVAL4 + | (tag_size - 1)); + + if (!is_writing) + tag_size += SKIPPED_SPARE_BYTES; + dma_prepare(tag_ptr, tag_size, is_writing); + } else { + tag_size = mtd->oobsize; + reg_val |= (CFG_SKIP_SPARE_DISABLE + | CFG_HW_ECC_CORRECTION_DISABLE + | CFG_ECC_EN_TAG_DISABLE + | CFG_HW_ECC_DISABLE + | (tag_size - 1)); + dma_prepare(chip->oob_poi, tag_size, is_writing); + } + writel(reg_val, &info->reg->config); + + dma_prepare(buf, 1 << chip->page_shift, is_writing); + + writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config); + + writel(tag_size - 1, &info->reg->dma_cfg_b); + + nand_clear_interrupt_status(info->reg); + + reg_val = CMD_CLE | CMD_ALE + | CMD_SEC_CMD + | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT) + | CMD_A_VALID + | CMD_B_VALID + | (CMD_TRANS_SIZE_PAGE << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0; + if (!is_writing) + reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX); + else + reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX); + writel(reg_val, &info->reg->command); + + /* Setup DMA engine */ + reg_val = DMA_MST_CTRL_GO_ENABLE + | DMA_MST_CTRL_BURST_8WORDS + | DMA_MST_CTRL_EN_A_ENABLE + | DMA_MST_CTRL_EN_B_ENABLE; + + if (!is_writing) + reg_val |= DMA_MST_CTRL_DIR_READ; + else + reg_val |= DMA_MST_CTRL_DIR_WRITE; + + writel(reg_val, &info->reg->dma_mst_ctrl); + + start_command(info->reg); + + if (!nand_waitfor_cmd_completion(info->reg)) { + if (!is_writing) + printf("Read Page 0x%X timeout ", page); + else + printf("Write Page 0x%X timeout ", page); + if (with_ecc) + printf("with ECC"); + else + printf("without ECC"); + printf("\n"); + return -EIO; + } + + if (with_ecc && !is_writing) { + memcpy(chip->oob_poi, tag_ptr, + SKIPPED_SPARE_BYTES); + memcpy(chip->oob_poi + free->offset, + tag_ptr + SKIPPED_SPARE_BYTES, + chip->ecc.layout->oobavail); + reg_val = (u32)check_ecc_error(info->reg, (u8 *)buf, + 1 << chip->page_shift, + (u8 *)(tag_ptr + SKIPPED_SPARE_BYTES), + chip->ecc.layout->oobavail); + if (reg_val & ECC_TAG_ERROR) + printf("Read Page 0x%X tag ECC error\n", page); + if (reg_val & ECC_DATA_ERROR) + printf("Read Page 0x%X data ECC error\n", + page); + if (reg_val & (ECC_DATA_ERROR | ECC_TAG_ERROR)) + return -EIO; + } + return 0; +} + +/** + * Hardware ecc based page read function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf buffer to store read data + * @param page page number to read + * @return 0 when successfully completed + * -EIO when command timeout + */ +static int nand_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int page) +{ + return nand_rw_page(mtd, chip, buf, page, 1, 0); +} + +/** + * Hardware ecc based page write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + */ +static void nand_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf) +{ + int page; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + page = (readl(&info->reg->addr_reg1) >> 16) | + (readl(&info->reg->addr_reg2) << 16); + + nand_rw_page(mtd, chip, (uint8_t *)buf, page, 1, 1); +} + + +/** + * Read raw page data without ecc + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf buffer to store read data + * @param page page number to read + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int page) +{ + return nand_rw_page(mtd, chip, buf, page, 0, 0); +} + +/** + * Raw page write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + */ +static void nand_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf) +{ + int page; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + page = (readl(&info->reg->addr_reg1) >> 16) | + (readl(&info->reg->addr_reg2) << 16); + + nand_rw_page(mtd, chip, (uint8_t *)buf, page, 0, 1); +} + +/** + * OOB data read/write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to read + * @param with_ecc 1 to enable ECC, 0 to disable ECC + * @param is_writing 0 for read, 1 for write + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_rw_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page, int with_ecc, int is_writing) +{ + u32 reg_val; + int tag_size; + struct nand_oobfree *free = chip->ecc.layout->oobfree; + struct nand_drv *info; + + if (((int)chip->oob_poi) & 0x03) + return -EINVAL; + info = (struct nand_drv *)chip->priv; + if (set_bus_width_page_size(&info->config, ®_val)) + return -EINVAL; + + stop_command(info->reg); + + writel(virt_to_phys(chip->oob_poi), &info->reg->tag_ptr); + + /* Set ECC selection */ + tag_size = mtd->oobsize; + if (with_ecc) + reg_val |= CFG_ECC_EN_TAG_ENABLE; + else + reg_val |= (CFG_ECC_EN_TAG_DISABLE); + + reg_val |= ((tag_size - 1) | + CFG_SKIP_SPARE_DISABLE | + CFG_HW_ECC_CORRECTION_DISABLE | + CFG_HW_ECC_DISABLE); + writel(reg_val, &info->reg->config); + + dma_prepare(chip->oob_poi, tag_size, is_writing); + + writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config); + + if (is_writing && with_ecc) + tag_size -= TAG_ECC_BYTES; + + writel(tag_size - 1, &info->reg->dma_cfg_b); + + nand_clear_interrupt_status(info->reg); + + reg_val = CMD_CLE | CMD_ALE + | CMD_SEC_CMD + | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT) + | CMD_B_VALID + | CMD_CE0; + if (!is_writing) + reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX); + else + reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX); + writel(reg_val, &info->reg->command); + + /* Setup DMA engine */ + reg_val = DMA_MST_CTRL_GO_ENABLE + | DMA_MST_CTRL_BURST_8WORDS + | DMA_MST_CTRL_EN_B_ENABLE; + if (!is_writing) + reg_val |= DMA_MST_CTRL_DIR_READ; + else + reg_val |= DMA_MST_CTRL_DIR_WRITE; + + writel(reg_val, &info->reg->dma_mst_ctrl); + + start_command(info->reg); + + if (!nand_waitfor_cmd_completion(info->reg)) { + if (!is_writing) + printf("Read OOB of Page 0x%X timeout\n", page); + else + printf("Write OOB of Page 0x%X timeout\n", page); + return -EIO; + } + + if (with_ecc && !is_writing) { + reg_val = (u32)check_ecc_error(info->reg, 0, 0, + (u8 *)(chip->oob_poi + free->offset), + chip->ecc.layout->oobavail); + if (reg_val & ECC_TAG_ERROR) + printf("Read OOB of Page 0x%X tag ECC error\n", page); + } + return 0; +} + +/** + * OOB data read function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to read + * @param sndcmd flag whether to issue read command or not + * @return 1 - issue read command next time + * 0 - not to issue + */ +static int nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page, int sndcmd) +{ + if (sndcmd) { + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + sndcmd = 0; + } + nand_rw_oob(mtd, chip, page, 0, 0); + return sndcmd; +} + +/** + * OOB data write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to write + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + + return nand_rw_oob(mtd, chip, page, 0, 1); +} + +/** + * Set up NAND memory timings according to the provided parameters + * + * @param timing Timing parameters + * @param reg NAND controller register address + */ +static void setup_timing(unsigned timing[FDT_NAND_TIMING_COUNT], + struct nand_ctlr *reg) +{ + u32 reg_val, clk_rate, clk_period, time_val; + + clk_rate = (u32)clock_get_periph_rate(PERIPH_ID_NDFLASH, + CLOCK_ID_PERIPH) / 1000000; + clk_period = 1000 / clk_rate; + reg_val = ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) << + TIMING_TRP_RESP_CNT_SHIFT) & TIMING_TRP_RESP_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWB] / clk_period) << + TIMING_TWB_CNT_SHIFT) & TIMING_TWB_CNT_MASK; + time_val = timing[FDT_NAND_MAX_TCR_TAR_TRR] / clk_period; + if (time_val > 2) + reg_val |= ((time_val - 2) << TIMING_TCR_TAR_TRR_CNT_SHIFT) & + TIMING_TCR_TAR_TRR_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWHR] / clk_period) << + TIMING_TWHR_CNT_SHIFT) & TIMING_TWHR_CNT_MASK; + time_val = timing[FDT_NAND_MAX_TCS_TCH_TALS_TALH] / clk_period; + if (time_val > 1) + reg_val |= ((time_val - 1) << TIMING_TCS_CNT_SHIFT) & + TIMING_TCS_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWH] / clk_period) << + TIMING_TWH_CNT_SHIFT) & TIMING_TWH_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWP] / clk_period) << + TIMING_TWP_CNT_SHIFT) & TIMING_TWP_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TRH] / clk_period) << + TIMING_TRH_CNT_SHIFT) & TIMING_TRH_CNT_MASK; + reg_val |= ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) << + TIMING_TRP_CNT_SHIFT) & TIMING_TRP_CNT_MASK; + writel(reg_val, ®->timing); + + reg_val = 0; + time_val = timing[FDT_NAND_TADL] / clk_period; + if (time_val > 2) + reg_val = (time_val - 2) & TIMING2_TADL_CNT_MASK; + writel(reg_val, ®->timing2); +} + +/** + * Decode NAND parameters from the device tree + * + * @param blob Device tree blob + * @param node Node containing "nand-flash" compatble node + * @return 0 if ok, -ve on error (FDT_ERR_...) + */ +static int fdt_decode_nand(const void *blob, int node, struct fdt_nand *config) +{ + int err; + + config->reg = (struct nand_ctlr *)fdtdec_get_addr(blob, node, "reg"); + config->enabled = fdtdec_get_is_enabled(blob, node); + config->width = fdtdec_get_int(blob, node, "nvidia,nand-width", 8); + err = fdtdec_decode_gpio(blob, node, "nvidia,wp-gpios", + &config->wp_gpio); + if (err) + return err; + err = fdtdec_get_int_array(blob, node, "nvidia,timing", + config->timing, FDT_NAND_TIMING_COUNT); + if (err < 0) + return err; + + /* Now look up the controller and decode that */ + node = fdt_next_node(blob, node, NULL); + if (node < 0) + return node; + + return 0; +} + +/** + * Board-specific NAND initialization + * + * @param nand nand chip info structure + * @return 0, after initialized, -1 on error + */ +int tegra_nand_init(struct nand_chip *nand, int devnum) +{ + struct nand_drv *info = &nand_ctrl; + struct fdt_nand *config = &info->config; + int node, ret; + + node = fdtdec_next_compatible(gd->fdt_blob, 0, + COMPAT_NVIDIA_TEGRA20_NAND); + if (node < 0) + return -1; + if (fdt_decode_nand(gd->fdt_blob, node, config)) { + printf("Could not decode nand-flash in device tree\n"); + return -1; + } + if (!config->enabled) + return -1; + info->reg = config->reg; + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.layout = &eccoob; + + nand->options = LP_OPTIONS; + nand->cmdfunc = nand_command; + nand->read_byte = read_byte; + nand->ecc.read_page = nand_read_page_hwecc; + nand->ecc.write_page = nand_write_page_hwecc; + nand->ecc.read_page_raw = nand_read_page_raw; + nand->ecc.write_page_raw = nand_write_page_raw; + nand->ecc.read_oob = nand_read_oob; + nand->ecc.write_oob = nand_write_oob; + nand->select_chip = nand_select_chip; + nand->dev_ready = nand_dev_ready; + nand->priv = &nand_ctrl; + + /* Adjust controller clock rate */ + clock_start_periph_pll(PERIPH_ID_NDFLASH, CLOCK_ID_PERIPH, 52000000); + + /* Adjust timing for NAND device */ + setup_timing(config->timing, info->reg); + + funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_DEFAULT); + fdtdec_setup_gpio(&config->wp_gpio); + gpio_direction_output(config->wp_gpio.gpio, 1); + + our_mtd = &nand_info[devnum]; + our_mtd->priv = nand; + ret = nand_scan_ident(our_mtd, CONFIG_SYS_NAND_MAX_CHIPS, NULL); + if (ret) + return ret; + + nand->ecc.size = our_mtd->writesize; + nand->ecc.bytes = our_mtd->oobsize; + + ret = nand_scan_tail(our_mtd); + if (ret) + return ret; + + ret = nand_register(devnum); + if (ret) + return ret; + + return 0; +} + +void board_nand_init(void) +{ + struct nand_chip *nand = &nand_chip[0]; + + if (tegra_nand_init(nand, 0)) + puts("Tegra NAND init failed\n"); +} diff --git a/drivers/mtd/nand/tegra_nand.h b/drivers/mtd/nand/tegra_nand.h new file mode 100644 index 000000000..7e74be75f --- /dev/null +++ b/drivers/mtd/nand/tegra_nand.h @@ -0,0 +1,257 @@ +/* + * (C) Copyright 2011 NVIDIA Corporation <www.nvidia.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* register offset */ +#define COMMAND_0 0x00 +#define CMD_GO (1 << 31) +#define CMD_CLE (1 << 30) +#define CMD_ALE (1 << 29) +#define CMD_PIO (1 << 28) +#define CMD_TX (1 << 27) +#define CMD_RX (1 << 26) +#define CMD_SEC_CMD (1 << 25) +#define CMD_AFT_DAT_MASK (1 << 24) +#define CMD_AFT_DAT_DISABLE 0 +#define CMD_AFT_DAT_ENABLE (1 << 24) +#define CMD_TRANS_SIZE_SHIFT 20 +#define CMD_TRANS_SIZE_PAGE 8 +#define CMD_A_VALID (1 << 19) +#define CMD_B_VALID (1 << 18) +#define CMD_RD_STATUS_CHK (1 << 17) +#define CMD_R_BSY_CHK (1 << 16) +#define CMD_CE7 (1 << 15) +#define CMD_CE6 (1 << 14) +#define CMD_CE5 (1 << 13) +#define CMD_CE4 (1 << 12) +#define CMD_CE3 (1 << 11) +#define CMD_CE2 (1 << 10) +#define CMD_CE1 (1 << 9) +#define CMD_CE0 (1 << 8) +#define CMD_CLE_BYTE_SIZE_SHIFT 4 +enum { + CMD_CLE_BYTES1 = 0, + CMD_CLE_BYTES2, + CMD_CLE_BYTES3, + CMD_CLE_BYTES4, +}; +#define CMD_ALE_BYTE_SIZE_SHIFT 0 +enum { + CMD_ALE_BYTES1 = 0, + CMD_ALE_BYTES2, + CMD_ALE_BYTES3, + CMD_ALE_BYTES4, + CMD_ALE_BYTES5, + CMD_ALE_BYTES6, + CMD_ALE_BYTES7, + CMD_ALE_BYTES8 +}; + +#define STATUS_0 0x04 +#define STATUS_RBSY0 (1 << 8) + +#define ISR_0 0x08 +#define ISR_IS_CMD_DONE (1 << 5) +#define ISR_IS_ECC_ERR (1 << 4) + +#define IER_0 0x0C + +#define CFG_0 0x10 +#define CFG_HW_ECC_MASK (1 << 31) +#define CFG_HW_ECC_DISABLE 0 +#define CFG_HW_ECC_ENABLE (1 << 31) +#define CFG_HW_ECC_SEL_MASK (1 << 30) +#define CFG_HW_ECC_SEL_HAMMING 0 +#define CFG_HW_ECC_SEL_RS (1 << 30) +#define CFG_HW_ECC_CORRECTION_MASK (1 << 29) +#define CFG_HW_ECC_CORRECTION_DISABLE 0 +#define CFG_HW_ECC_CORRECTION_ENABLE (1 << 29) +#define CFG_PIPELINE_EN_MASK (1 << 28) +#define CFG_PIPELINE_EN_DISABLE 0 +#define CFG_PIPELINE_EN_ENABLE (1 << 28) +#define CFG_ECC_EN_TAG_MASK (1 << 27) +#define CFG_ECC_EN_TAG_DISABLE 0 +#define CFG_ECC_EN_TAG_ENABLE (1 << 27) +#define CFG_TVALUE_MASK (3 << 24) +enum { + CFG_TVAL4 = 0 << 24, + CFG_TVAL6 = 1 << 24, + CFG_TVAL8 = 2 << 24 +}; +#define CFG_SKIP_SPARE_MASK (1 << 23) +#define CFG_SKIP_SPARE_DISABLE 0 +#define CFG_SKIP_SPARE_ENABLE (1 << 23) +#define CFG_COM_BSY_MASK (1 << 22) +#define CFG_COM_BSY_DISABLE 0 +#define CFG_COM_BSY_ENABLE (1 << 22) +#define CFG_BUS_WIDTH_MASK (1 << 21) +#define CFG_BUS_WIDTH_8BIT 0 +#define CFG_BUS_WIDTH_16BIT (1 << 21) +#define CFG_LPDDR1_MODE_MASK (1 << 20) +#define CFG_LPDDR1_MODE_DISABLE 0 +#define CFG_LPDDR1_MODE_ENABLE (1 << 20) +#define CFG_EDO_MODE_MASK (1 << 19) +#define CFG_EDO_MODE_DISABLE 0 +#define CFG_EDO_MODE_ENABLE (1 << 19) +#define CFG_PAGE_SIZE_SEL_MASK (7 << 16) +enum { + CFG_PAGE_SIZE_256 = 0 << 16, + CFG_PAGE_SIZE_512 = 1 << 16, + CFG_PAGE_SIZE_1024 = 2 << 16, + CFG_PAGE_SIZE_2048 = 3 << 16, + CFG_PAGE_SIZE_4096 = 4 << 16 +}; +#define CFG_SKIP_SPARE_SEL_MASK (3 << 14) +enum { + CFG_SKIP_SPARE_SEL_4 = 0 << 14, + CFG_SKIP_SPARE_SEL_8 = 1 << 14, + CFG_SKIP_SPARE_SEL_12 = 2 << 14, + CFG_SKIP_SPARE_SEL_16 = 3 << 14 +}; +#define CFG_TAG_BYTE_SIZE_MASK 0x1FF + +#define TIMING_0 0x14 +#define TIMING_TRP_RESP_CNT_SHIFT 28 +#define TIMING_TRP_RESP_CNT_MASK (0xf << TIMING_TRP_RESP_CNT_SHIFT) +#define TIMING_TWB_CNT_SHIFT 24 +#define TIMING_TWB_CNT_MASK (0xf << TIMING_TWB_CNT_SHIFT) +#define TIMING_TCR_TAR_TRR_CNT_SHIFT 20 +#define TIMING_TCR_TAR_TRR_CNT_MASK (0xf << TIMING_TCR_TAR_TRR_CNT_SHIFT) +#define TIMING_TWHR_CNT_SHIFT 16 +#define TIMING_TWHR_CNT_MASK (0xf << TIMING_TWHR_CNT_SHIFT) +#define TIMING_TCS_CNT_SHIFT 14 +#define TIMING_TCS_CNT_MASK (3 << TIMING_TCS_CNT_SHIFT) +#define TIMING_TWH_CNT_SHIFT 12 +#define TIMING_TWH_CNT_MASK (3 << TIMING_TWH_CNT_SHIFT) +#define TIMING_TWP_CNT_SHIFT 8 +#define TIMING_TWP_CNT_MASK (0xf << TIMING_TWP_CNT_SHIFT) +#define TIMING_TRH_CNT_SHIFT 4 +#define TIMING_TRH_CNT_MASK (3 << TIMING_TRH_CNT_SHIFT) +#define TIMING_TRP_CNT_SHIFT 0 +#define TIMING_TRP_CNT_MASK (0xf << TIMING_TRP_CNT_SHIFT) + +#define RESP_0 0x18 + +#define TIMING2_0 0x1C +#define TIMING2_TADL_CNT_SHIFT 0 +#define TIMING2_TADL_CNT_MASK (0xf << TIMING2_TADL_CNT_SHIFT) + +#define CMD_REG1_0 0x20 +#define CMD_REG2_0 0x24 +#define ADDR_REG1_0 0x28 +#define ADDR_REG2_0 0x2C + +#define DMA_MST_CTRL_0 0x30 +#define DMA_MST_CTRL_GO_MASK (1 << 31) +#define DMA_MST_CTRL_GO_DISABLE 0 +#define DMA_MST_CTRL_GO_ENABLE (1 << 31) +#define DMA_MST_CTRL_DIR_MASK (1 << 30) +#define DMA_MST_CTRL_DIR_READ 0 +#define DMA_MST_CTRL_DIR_WRITE (1 << 30) +#define DMA_MST_CTRL_PERF_EN_MASK (1 << 29) +#define DMA_MST_CTRL_PERF_EN_DISABLE 0 +#define DMA_MST_CTRL_PERF_EN_ENABLE (1 << 29) +#define DMA_MST_CTRL_REUSE_BUFFER_MASK (1 << 27) +#define DMA_MST_CTRL_REUSE_BUFFER_DISABLE 0 +#define DMA_MST_CTRL_REUSE_BUFFER_ENABLE (1 << 27) +#define DMA_MST_CTRL_BURST_SIZE_SHIFT 24 +#define DMA_MST_CTRL_BURST_SIZE_MASK (7 << DMA_MST_CTRL_BURST_SIZE_SHIFT) +enum { + DMA_MST_CTRL_BURST_1WORDS = 2 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_4WORDS = 3 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_8WORDS = 4 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_16WORDS = 5 << DMA_MST_CTRL_BURST_SIZE_SHIFT +}; +#define DMA_MST_CTRL_IS_DMA_DONE (1 << 20) +#define DMA_MST_CTRL_EN_A_MASK (1 << 2) +#define DMA_MST_CTRL_EN_A_DISABLE 0 +#define DMA_MST_CTRL_EN_A_ENABLE (1 << 2) +#define DMA_MST_CTRL_EN_B_MASK (1 << 1) +#define DMA_MST_CTRL_EN_B_DISABLE 0 +#define DMA_MST_CTRL_EN_B_ENABLE (1 << 1) + +#define DMA_CFG_A_0 0x34 +#define DMA_CFG_B_0 0x38 +#define FIFO_CTRL_0 0x3C +#define DATA_BLOCK_PTR_0 0x40 +#define TAG_PTR_0 0x44 +#define ECC_PTR_0 0x48 + +#define DEC_STATUS_0 0x4C +#define DEC_STATUS_A_ECC_FAIL (1 << 1) +#define DEC_STATUS_B_ECC_FAIL (1 << 0) + +#define BCH_CONFIG_0 0xCC +#define BCH_CONFIG_BCH_TVALUE_SHIFT 4 +#define BCH_CONFIG_BCH_TVALUE_MASK (3 << BCH_CONFIG_BCH_TVALUE_SHIFT) +enum { + BCH_CONFIG_BCH_TVAL4 = 0 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL8 = 1 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL14 = 2 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL16 = 3 << BCH_CONFIG_BCH_TVALUE_SHIFT +}; +#define BCH_CONFIG_BCH_ECC_MASK (1 << 0) +#define BCH_CONFIG_BCH_ECC_DISABLE 0 +#define BCH_CONFIG_BCH_ECC_ENABLE (1 << 0) + +#define BCH_DEC_RESULT_0 0xD0 +#define BCH_DEC_RESULT_CORRFAIL_ERR_MASK (1 << 8) +#define BCH_DEC_RESULT_PAGE_COUNT_MASK 0xFF + +#define BCH_DEC_STATUS_BUF_0 0xD4 +#define BCH_DEC_STATUS_FAIL_SEC_FLAG_MASK 0xFF000000 +#define BCH_DEC_STATUS_CORR_SEC_FLAG_MASK 0x00FF0000 +#define BCH_DEC_STATUS_FAIL_TAG_MASK (1 << 14) +#define BCH_DEC_STATUS_CORR_TAG_MASK (1 << 13) +#define BCH_DEC_STATUS_MAX_CORR_CNT_MASK (0x1f << 8) +#define BCH_DEC_STATUS_PAGE_NUMBER_MASK 0xFF + +#define LP_OPTIONS (NAND_NO_READRDY | NAND_NO_AUTOINCR) + +struct nand_ctlr { + u32 command; /* offset 00h */ + u32 status; /* offset 04h */ + u32 isr; /* offset 08h */ + u32 ier; /* offset 0Ch */ + u32 config; /* offset 10h */ + u32 timing; /* offset 14h */ + u32 resp; /* offset 18h */ + u32 timing2; /* offset 1Ch */ + u32 cmd_reg1; /* offset 20h */ + u32 cmd_reg2; /* offset 24h */ + u32 addr_reg1; /* offset 28h */ + u32 addr_reg2; /* offset 2Ch */ + u32 dma_mst_ctrl; /* offset 30h */ + u32 dma_cfg_a; /* offset 34h */ + u32 dma_cfg_b; /* offset 38h */ + u32 fifo_ctrl; /* offset 3Ch */ + u32 data_block_ptr; /* offset 40h */ + u32 tag_ptr; /* offset 44h */ + u32 resv1; /* offset 48h */ + u32 dec_status; /* offset 4Ch */ + u32 hwstatus_cmd; /* offset 50h */ + u32 hwstatus_mask; /* offset 54h */ + u32 resv2[29]; + u32 bch_config; /* offset CCh */ + u32 bch_dec_result; /* offset D0h */ + u32 bch_dec_status_buf; + /* offset D4h */ +}; diff --git a/drivers/spi/tegra_spi.c b/drivers/spi/tegra_spi.c index 2355e022b..18b00b2ca 100644 --- a/drivers/spi/tegra_spi.c +++ b/drivers/spi/tegra_spi.c @@ -72,9 +72,9 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, return NULL; } - if (max_hz > TEGRA20_SPI_MAX_FREQ) { + if (max_hz > TEGRA_SPI_MAX_FREQ) { printf("SPI error: unsupported frequency %d Hz. Max frequency" - " is %d Hz\n", max_hz, TEGRA20_SPI_MAX_FREQ); + " is %d Hz\n", max_hz, TEGRA_SPI_MAX_FREQ); return NULL; } @@ -86,7 +86,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, spi->slave.bus = bus; spi->slave.cs = cs; spi->freq = max_hz; - spi->regs = (struct spi_tegra *)TEGRA20_SPI_BASE; + spi->regs = (struct spi_tegra *)NV_PA_SPI_BASE; spi->mode = mode; return &spi->slave; diff --git a/drivers/video/omap3_dss.c b/drivers/video/omap3_dss.c index 6686718b0..b1424bfd0 100644 --- a/drivers/video/omap3_dss.c +++ b/drivers/video/omap3_dss.c @@ -112,7 +112,7 @@ void omap3_dss_panel_config(const struct panel_config *panel_cfg) writel(panel_cfg->pol_freq, &dispc->pol_freq); writel(panel_cfg->divisor, &dispc->divisor); writel(panel_cfg->lcd_size, &dispc->size_lcd); - writel(panel_cfg->load_mode << FRAME_MODE_SHIFT, &dispc->config); + writel(panel_cfg->load_mode << LOADMODE_SHIFT, &dispc->config); writel(panel_cfg->panel_type << TFTSTN_SHIFT | panel_cfg->data_lines << DATALINES_SHIFT, &dispc->control); writel(panel_cfg->panel_color, &dispc->default_color0); @@ -121,7 +121,6 @@ void omap3_dss_panel_config(const struct panel_config *panel_cfg) if (!panel_cfg->frame_buffer) return; - writel(panel_cfg->load_mode << LOADMODE_SHIFT, &dispc->config); writel(8 << GFX_FORMAT_SHIFT | GFX_ENABLE, &dispc->gfx_attributes); writel(1, &dispc->gfx_row_inc); writel(1, &dispc->gfx_pixel_inc); diff --git a/include/configs/eb_cpux9k2.h b/include/configs/eb_cpux9k2.h index d4104de5f..9371ec31f 100644 --- a/include/configs/eb_cpux9k2.h +++ b/include/configs/eb_cpux9k2.h @@ -44,7 +44,12 @@ #define MACH_TYPE_EB_CPUX9K2 1977 #define CONFIG_MACH_TYPE MACH_TYPE_EB_CPUX9K2 /*--------------------------------------------------------------------------*/ -#define CONFIG_SYS_TEXT_BASE 0x00000000 +#ifndef CONFIG_RAMBOOT +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#else +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_TEXT_BASE 0x21f00000 +#endif #define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */ #define CONFIG_SYS_BOOT_SIZE 0x00 /* 0 KBytes */ diff --git a/include/configs/harmony.h b/include/configs/harmony.h index d0555c163..e407ff4ca 100644 --- a/include/configs/harmony.h +++ b/include/configs/harmony.h @@ -34,15 +34,15 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Harmony) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Harmony" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Harmony" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: keyboard satellite board UART, default */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE -#ifdef CONFIG_TEGRA20_ENABLE_UARTA +#ifdef CONFIG_TEGRA_ENABLE_UARTA /* UARTA: debug board UART */ #define CONFIG_SYS_NS16550_COM2 NV_PA_APB_UARTA_BASE #endif @@ -62,8 +62,15 @@ #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT -/* Environment not stored */ -#define CONFIG_ENV_IS_NOWHERE +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE + +/* Environment in NAND (which is 512M), aligned to start of last sector */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sector size */ /* USB Host support */ #define CONFIG_USB_EHCI @@ -80,6 +87,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/integrator-common.h b/include/configs/integrator-common.h new file mode 100644 index 000000000..564b418fa --- /dev/null +++ b/include/configs/integrator-common.h @@ -0,0 +1,103 @@ +/* + * (C) Copyright 2012 + * Linaro + * Linus Walleij <linus.walleij@linaro.org> + * Common ARM Integrator configuration settings + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#define CONFIG_INTEGRATOR + +#define CONFIG_SYS_TEXT_BASE 0x01000000 +#define CONFIG_SYS_MEMTEST_START 0x100000 +#define CONFIG_SYS_MEMTEST_END 0x10000000 +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */ +#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */ + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */ + +/* + * There are various dependencies on the core module (CM) fitted + * Users should refer to their CM user guide + */ +#include "armcoremodule.h" + +/* + * Initialize and remap the core module, use SPD to detect memory size + * If CONFIG_SKIP_LOWLEVEL_INIT is not defined & + * the core module has a CM_INIT register + * then the U-Boot initialisation code will + * e.g. ARM Boot Monitor or pre-loader is repeated once + * (to re-initialise any existing CM_INIT settings to safe values). + * + * This is usually not the desired behaviour since the platform + * will either reboot into the ARM monitor (or pre-loader) + * or continuously cycle thru it without U-Boot running, + * depending upon the setting of Integrator/CP switch S2-4. + * + * However it may be needed if Integrator/CP switch S2-1 + * is set OFF to boot direct into U-Boot. + * In that case comment out the line below. + */ +#define CONFIG_CM_INIT +#define CONFIG_CM_REMAP +#define CONFIG_CM_SPD_DETECT + +/* + * The ARM boot monitor initializes the board. + * However, the default U-Boot code also performs the initialization. + * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT + * - see documentation supplied with board for details of how to choose the + * image to run at reset/power up + * e.g. whether the ARM Boot Monitor runs before U-Boot + */ +/* #define CONFIG_SKIP_LOWLEVEL_INIT */ + +/* + * The ARM boot monitor does not relocate U-Boot. + * However, the default U-Boot code performs the relocation check, + * and may relocate the code if the memory map is changed. + * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT + */ +/* #define SKIP_CONFIG_RELOCATE_UBOOT */ + + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET diff --git a/include/configs/integratorap.h b/include/configs/integratorap.h index 2770c82b5..c6907b512 100644 --- a/include/configs/integratorap.h +++ b/include/configs/integratorap.h @@ -31,32 +31,11 @@ #ifndef __CONFIG_H #define __CONFIG_H -#define CONFIG_INTEGRATOR +#include "integrator-common.h" + +/* Integrator/AP-specific configuration */ #define CONFIG_ARCH_INTEGRATOR -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SYS_TEXT_BASE 0x01000000 -#define CONFIG_SYS_MEMTEST_START 0x100000 -#define CONFIG_SYS_MEMTEST_END 0x10000000 -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_HZ_CLOCK 24000000 /* Timer 1 is clocked at 24Mhz */ -#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */ - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */ - -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_CM_INIT 1 -#define CONFIG_CM_REMAP 1 -#define CONFIG_CM_SPD_DETECT - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* * PL010 Configuration @@ -90,29 +69,7 @@ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT "Integrator-AP # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_FLASH_BASE 0x24000000 diff --git a/include/configs/integratorcp.h b/include/configs/integratorcp.h index d5043df6f..ca02a6f1d 100644 --- a/include/configs/integratorcp.h +++ b/include/configs/integratorcp.h @@ -31,32 +31,11 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* Integrator-specific configuration */ -#define CONFIG_INTEGRATOR -#define CONFIG_ARCH_CINTEGRATOR -#define CONFIG_CM_INIT -#define CONFIG_CM_REMAP -#define CONFIG_CM_SPD_DETECT +#include "integrator-common.h" -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SYS_TEXT_BASE 0x01000000 -#define CONFIG_SYS_MEMTEST_START 0x100000 -#define CONFIG_SYS_MEMTEST_END 0x10000000 -#define CONFIG_SYS_HZ 1000 +/* Integrator CP-specific configuration */ +#define CONFIG_ARCH_CINTEGRATOR #define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer 1 is clocked at 1Mhz */ -#define CONFIG_SYS_TIMERBASE 0x13000100 - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */ - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* * Hardware drivers @@ -66,9 +45,7 @@ #define CONFIG_SMC91111_BASE 0xC8000000 #undef CONFIG_SMC91111_EXT_PHY -/* - * NS16550 Configuration - */ +/* PL011 configuration */ #define CONFIG_PL011_SERIAL #define CONFIG_PL011_CLOCK 14745600 #define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, (void *)CONFIG_SYS_SERIAL1 } @@ -77,16 +54,6 @@ #define CONFIG_SYS_SERIAL0 0x16000000 #define CONFIG_SYS_SERIAL1 0x17000000 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* * Command line configuration. */ @@ -102,32 +69,10 @@ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "Integrator-CP # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/ -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- +/* * FLASH and environment organization - * Top varies according to amount fitted * Reserve top 4 blocks of flash * - ARM Boot Monitor @@ -136,7 +81,6 @@ * - U-Boot environment * * Base is always 0x24000000 - */ #define CONFIG_SYS_FLASH_BASE 0x24000000 #define CONFIG_SYS_FLASH_CFI 1 @@ -178,53 +122,4 @@ #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */ #define CONFIG_ENV_SIZE 8192 /* 8KB */ -/* - * The ARM boot monitor initializes the board. - * However, the default U-Boot code also performs the initialization. - * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT - * - see documentation supplied with board for details of how to choose the - * image to run at reset/power up - * e.g. whether the ARM Boot Monitor runs before U-Boot - -#define CONFIG_SKIP_LOWLEVEL_INIT - - */ - -/* - * The ARM boot monitor does not relocate U-Boot. - * However, the default U-Boot code performs the relocation check, - * and may relocate the code if the memory map is changed. - * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT - -#define SKIP_CONFIG_RELOCATE_UBOOT - - */ -/*----------------------------------------------------------------------- - * There are various dependencies on the core module (CM) fitted - * Users should refer to their CM user guide - * - when porting adjust u-boot/Makefile accordingly - * to define the necessary CONFIG_ s for the CM involved - * see e.g. cp_926ejs_config - */ - -#include "armcoremodule.h" - -/* - * If CONFIG_SKIP_LOWLEVEL_INIT is not defined & - * the core module has a CM_INIT register - * then the U-Boot initialisation code will - * e.g. ARM Boot Monitor or pre-loader is repeated once - * (to re-initialise any existing CM_INIT settings to safe values). - * - * This is usually not the desired behaviour since the platform - * will either reboot into the ARM monitor (or pre-loader) - * or continuously cycle thru it without U-Boot running, - * depending upon the setting of Integrator/CP switch S2-4. - * - * However it may be needed if Integrator/CP switch S2-1 - * is set OFF to boot direct into U-Boot. - * In that case comment out the line below. -#undef CONFIG_CM_INIT - */ - #endif /* __CONFIG_H */ diff --git a/include/configs/medcom.h b/include/configs/medcom.h index bce03a49f..678b36b6c 100644 --- a/include/configs/medcom.h +++ b/include/configs/medcom.h @@ -35,11 +35,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Medcom) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Medcom" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Medcom" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F @@ -78,6 +78,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/mt_ventoux.h b/include/configs/mt_ventoux.h index 5db6d5766..8d35943fa 100644 --- a/include/configs/mt_ventoux.h +++ b/include/configs/mt_ventoux.h @@ -2,6 +2,9 @@ * Copyright (C) 2011 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. * + * + * Configuration settings for the Teejet mt_ventoux board. + * * Copyright (C) 2009 TechNexion Ltd. * * This program is free software; you can redistribute it and/or modify @@ -24,6 +27,10 @@ #include "tam3517-common.h" +#undef CONFIG_SYS_MALLOC_LEN +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ + 6 * 1024 * 1024) + #define MACH_TYPE_AM3517_MT_VENTOUX 3832 #define CONFIG_MACH_TYPE MACH_TYPE_AM3517_MT_VENTOUX @@ -31,6 +38,7 @@ #define CONFIG_BOOTFILE "uImage" #define CONFIG_AUTO_COMPLETE +#define CONFIG_OMAP3_GPIO_4 #define CONFIG_HOSTNAME mt_ventoux /* @@ -62,6 +70,15 @@ #define CONFIG_FPGA_DELAY() udelay(1) #define CONFIG_SYS_FPGA_PROG_FEEDBACK +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_CMD_BMP +#define CONFIG_VIDEO_OMAP3 /* DSS Support */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + #define CONFIG_EXTRA_ENV_SETTINGS CONFIG_TAM3517_SETTINGS \ "bootcmd=run net_nfs\0" diff --git a/include/configs/paz00.h b/include/configs/paz00.h index 0eb9f3b60..24cda4839 100644 --- a/include/configs/paz00.h +++ b/include/configs/paz00.h @@ -27,11 +27,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Paz00) MOD # " -#define CONFIG_TEGRA20_BOARD_STRING "Compal Paz00" +#define CONFIG_TEGRA_BOARD_STRING "Compal Paz00" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA +#define CONFIG_TEGRA_ENABLE_UARTA #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_PAZ00 @@ -51,8 +51,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 1024 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((1024 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI @@ -68,6 +69,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/plutux.h b/include/configs/plutux.h index 42291d4e2..65b42edc2 100644 --- a/include/configs/plutux.h +++ b/include/configs/plutux.h @@ -35,11 +35,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Plutux) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Plutux" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Plutux" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F @@ -78,6 +78,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index afc4a855b..de19e38de 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -27,7 +27,7 @@ #include <asm/sizes.h> /* LP0 suspend / resume */ -#define CONFIG_TEGRA20_LP0 +#define CONFIG_TEGRA_LP0 #define CONFIG_AES #define CONFIG_TEGRA_PMU #define CONFIG_TPS6586X_POWER @@ -42,11 +42,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (SeaBoard) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Seaboard" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Seaboard" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE /* On Seaboard: GPIO_PI3 = Port I = 8, bit = 3 */ @@ -77,8 +77,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 512 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((512 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI @@ -95,14 +96,23 @@ #define CONFIG_CMD_DHCP /* Enable keyboard */ -#define CONFIG_TEGRA20_KEYBOARD +#define CONFIG_TEGRA_KEYBOARD #define CONFIG_KEYBOARD -#undef TEGRA20_DEVICE_SETTINGS -#define TEGRA20_DEVICE_SETTINGS "stdin=serial,tegra-kbc\0" \ - "stdout=serial\0" \ - "stderr=serial\0" +#undef TEGRA_DEVICE_SETTINGS +#define TEGRA_DEVICE_SETTINGS "stdin=serial,tegra-kbc\0" \ + "stdout=serial\0" \ + "stderr=serial\0" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND + +/* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +/* Somewhat oddly, the NAND base address must be a config option */ +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE #endif /* __CONFIG_H */ diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h index a2a0156a6..a881eef30 100644 --- a/include/configs/stamp9g20.h +++ b/include/configs/stamp9g20.h @@ -59,6 +59,7 @@ #define CONFIG_INITRD_TAG /* pass initrd param to kernel */ #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ #define CONFIG_BOARD_EARLY_INIT_f /* call board_early_init_f() */ +#define CONFIG_BOARD_POSTCLK_INIT /* call board_postclk_init() */ #define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */ /* setting board specific options */ diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 375265d47..a13fd9376 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -124,6 +124,7 @@ #define CONFIG_CMD_NAND /* NAND support */ #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FLASH /* only NAND on the SOM */ #undef CONFIG_CMD_IMLS @@ -134,6 +135,9 @@ #define CONFIG_SYS_I2C_SLAVE 1 #define CONFIG_SYS_I2C_BUS 0 #define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CONFIG_DRIVER_OMAP34XX_I2C @@ -347,4 +351,66 @@ "fi;" \ "else echo U-Boot not downloaded..exiting;fi\0" \ + +/* + * this is common code for all TAM3517 boards. + * MAC address is stored from manufacturer in + * I2C EEPROM + */ +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) + +/* + * The I2C EEPROM on the TAM3517 contains + * mac address and production data + */ +struct tam3517_module_info { + char customer[48]; + char product[48]; + + /* + * bit 0~47 : sequence number + * bit 48~55 : week of year, from 0. + * bit 56~63 : year + */ + unsigned long long sequence_number; + + /* + * bit 0~7 : revision fixed + * bit 8~15 : revision major + * bit 16~31 : TNxxx + */ + unsigned int revision; + unsigned char eth_addr[4][8]; + unsigned char _rev[100]; +}; + +#define TAM3517_READ_MAC_FROM_EEPROM \ +do { \ + struct tam3517_module_info info;\ + char buf[80], ethname[20]; \ + int i; \ + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \ + if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ + (void *)&info, sizeof(info))) \ + break; \ + memset(buf, 0, sizeof(buf)); \ + for (i = 0 ; i < ARRAY_SIZE(info.eth_addr); i++) { \ + sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ + info.eth_addr[i][5], \ + info.eth_addr[i][4], \ + info.eth_addr[i][3], \ + info.eth_addr[i][2], \ + info.eth_addr[i][1], \ + info.eth_addr[i][0]); \ + \ + if (i) \ + sprintf(ethname, "eth%daddr", i); \ + else \ + sprintf(ethname, "ethaddr"); \ + printf("Setting %s from EEPROM with %s\n", ethname, buf);\ + setenv(ethname, buf); \ + } \ +} while (0) +#endif + #endif /* __TAM3517_H */ diff --git a/include/configs/tec.h b/include/configs/tec.h index 9b3f88dff..d5da3c7a8 100644 --- a/include/configs/tec.h +++ b/include/configs/tec.h @@ -35,24 +35,32 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (TEC) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Tamonten Evaluation Carrier" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten Evaluation Carrier" #define CONFIG_SYS_BOARD_ODMDATA 0x2b0d8011 /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ENV_IS_NOWHERE - /* SD/MMC */ #define CONFIG_MMC #define CONFIG_GENERIC_MMC #define CONFIG_TEGRA_MMC #define CONFIG_CMD_MMC +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE + +/* Environment in NAND, aligned to start of last sector */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */ + /* USB host support */ #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA @@ -79,6 +87,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/tegra20-common-post.h b/include/configs/tegra-common-post.h index 42f270f7b..168b64be5 100644 --- a/include/configs/tegra20-common-post.h +++ b/include/configs/tegra-common-post.h @@ -21,8 +21,8 @@ * MA 02111-1307 USA */ -#ifndef __TEGRA20_COMMON_POST_H -#define __TEGRA20_COMMON_POST_H +#ifndef __TEGRA_COMMON_POST_H +#define __TEGRA_COMMON_POST_H #ifdef CONFIG_BOOTCOMMAND @@ -141,7 +141,7 @@ #endif #define CONFIG_EXTRA_ENV_SETTINGS \ - TEGRA20_DEVICE_SETTINGS \ + TEGRA_DEVICE_SETTINGS \ "fdt_load=0x01000000\0" \ "fdt_high=01100000\0" \ BOOTCMDS_COMMON @@ -174,8 +174,8 @@ #ifdef CONFIG_GENERIC_MMC #undef CONFIG_GENERIC_MMC #endif -#ifdef CONFIG_TEGRA20_MMC -#undef CONFIG_TEGRA20_MMC +#ifdef CONFIG_TEGRA_MMC +#undef CONFIG_TEGRA_MMC #endif #ifdef CONFIG_CMD_MMC #undef CONFIG_CMD_MMC @@ -211,4 +211,4 @@ #endif /* CONFIG_SPL_BUILD */ -#endif /* __TEGRA20_COMMON_POST_H */ +#endif /* __TEGRA_COMMON_POST_H */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 4c02f2054..098cdb446 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -54,7 +54,7 @@ #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_OF_LIBFDT /* enable passing of devicetree */ -#ifdef CONFIG_TEGRA20_LP0 +#ifdef CONFIG_TEGRA_LP0 #define TEGRA_LP0_ADDR 0x1C406000 #define TEGRA_LP0_SIZE 0x2000 #define TEGRA_LP0_VEC \ @@ -132,9 +132,9 @@ /* Environment information, boards can override if required */ #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define TEGRA20_DEVICE_SETTINGS "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" +#define TEGRA_DEVICE_SETTINGS "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" #define CONFIG_LOADADDR 0x408000 /* def. location for kernel */ #define CONFIG_BOOTDELAY 2 /* -1 to disable auto boot */ @@ -157,7 +157,7 @@ /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) -#define CONFIG_SYS_MEMTEST_START (TEGRA20_SDRC_CS0 + 0x600000) +#define CONFIG_SYS_MEMTEST_START (NV_PA_SDRC_CS0 + 0x600000) #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000) #define CONFIG_SYS_LOAD_ADDR (0xA00800) /* default */ @@ -169,7 +169,7 @@ * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 TEGRA20_SDRC_CS0 +#define PHYS_SDRAM_1 NV_PA_SDRC_CS0 #define PHYS_SDRAM_1_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_TEXT_BASE 0x0010c000 @@ -201,4 +201,6 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/tegra20/u-boot-spl.lds" +#define CONFIG_SYS_NAND_SELF_INIT + #endif /* __TEGRA20_COMMON_H */ diff --git a/include/configs/trimslice.h b/include/configs/trimslice.h index b3c524981..a46890c09 100644 --- a/include/configs/trimslice.h +++ b/include/configs/trimslice.h @@ -34,12 +34,12 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (TrimSlice) # " -#define CONFIG_TEGRA20_BOARD_STRING "Compulab Trimslice" +#define CONFIG_TEGRA_BOARD_STRING "Compulab Trimslice" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA -#define CONFIG_TEGRA20_UARTA_GPU +#define CONFIG_TEGRA_ENABLE_UARTA +#define CONFIG_TEGRA_UARTA_GPU #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_TRIMSLICE @@ -94,6 +94,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/ventana.h b/include/configs/ventana.h index 25ec2ebfe..7d3a54f74 100644 --- a/include/configs/ventana.h +++ b/include/configs/ventana.h @@ -34,11 +34,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Ventana) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Ventana" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Ventana" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_MACH_TYPE MACH_TYPE_VENTANA @@ -58,8 +58,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 1024 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((1024 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI @@ -75,6 +76,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/whistler.h b/include/configs/whistler.h index b747d0e2b..6c565bae1 100644 --- a/include/configs/whistler.h +++ b/include/configs/whistler.h @@ -34,12 +34,12 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Whistler) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Whistler" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Whistler" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA -#define CONFIG_TEGRA20_UARTA_UAA_UAB +#define CONFIG_TEGRA_ENABLE_UARTA +#define CONFIG_TEGRA_UARTA_UAA_UAB #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_WHISTLER @@ -72,8 +72,9 @@ * particular card is standard practice as far as I know. */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 512 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((512 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI @@ -89,6 +90,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/fdtdec.h b/include/fdtdec.h index a8f783ffd..474a4b90e 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -63,6 +63,7 @@ enum fdt_compat_id { COMPAT_NVIDIA_TEGRA20_EMC, /* Tegra20 memory controller */ COMPAT_NVIDIA_TEGRA20_EMC_TABLE, /* Tegra20 memory timing table */ COMPAT_NVIDIA_TEGRA20_KBC, /* Tegra20 Keyboard */ + COMPAT_NVIDIA_TEGRA20_NAND, /* Tegra2 NAND controller */ COMPAT_COUNT, }; diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 82704de08..dc839e715 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -391,9 +391,10 @@ struct nand_ecc_ctrl { * consecutive order. */ struct nand_buffers { - uint8_t ecccalc[NAND_MAX_OOBSIZE]; - uint8_t ecccode[NAND_MAX_OOBSIZE]; - uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; + uint8_t ecccalc[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t ecccode[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t databuf[ALIGN(NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE, + ARCH_DMA_MINALIGN)]; }; /** diff --git a/include/mmc.h b/include/mmc.h index 7546b4a6c..b63b2c32a 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -160,6 +160,7 @@ #define EXT_CSD_CARD_TYPE 196 /* RO */ #define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */ #define EXT_CSD_HC_ERASE_GRP_SIZE 224 /* RO */ +#define EXT_CSD_BOOT_MULT 226 /* RO */ /* * EXT_CSD field definitions diff --git a/lib/fdtdec.c b/lib/fdtdec.c index af17ac1b7..69c63db4b 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -42,6 +42,7 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(NVIDIA_TEGRA20_EMC, "nvidia,tegra20-emc"), COMPAT(NVIDIA_TEGRA20_EMC_TABLE, "nvidia,tegra20-emc-table"), COMPAT(NVIDIA_TEGRA20_KBC, "nvidia,tegra20-kbc"), + COMPAT(NVIDIA_TEGRA20_NAND, "nvidia,tegra20-nand"), }; const char *fdtdec_get_compatible(enum fdt_compat_id id) |