diff options
| -rw-r--r-- | arch/arm/cpu/arm1176/start.S | 91 |
1 files changed, 1 insertions, 90 deletions
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S index a7cf728ff..1fc1da071 100644 --- a/arch/arm/cpu/arm1176/start.S +++ b/arch/arm/cpu/arm1176/start.S @@ -33,11 +33,8 @@ #include <asm-offsets.h> #include <config.h> #include <version.h> -#ifdef CONFIG_ENABLE_MMU -#include <asm/proc/domain.h> -#endif -#if !defined(CONFIG_ENABLE_MMU) && !defined(CONFIG_SYS_PHY_UBOOT_BASE) +#ifndef CONFIG_SYS_PHY_UBOOT_BASE #define CONFIG_SYS_PHY_UBOOT_BASE CONFIG_SYS_UBOOT_BASE #endif @@ -105,14 +102,6 @@ _TEXT_BASE: #endif /* - * Below variable is very important because we use MMU in U-Boot. - * Without it, we cannot run code correctly before MMU is ON. - * by scsuh. - */ -_TEXT_PHY_BASE: - .word CONFIG_SYS_PHY_UBOOT_BASE - -/* * These are defined in the board-specific linker script. * Subtracting _start from them lets the linker put their * relative position in the executable instead of leaving @@ -298,44 +287,6 @@ fixnext: blo fixloop #endif -#ifdef CONFIG_ENABLE_MMU -enable_mmu: - /* enable domain access */ - ldr r5, =0x0000ffff - mcr p15, 0, r5, c3, c0, 0 /* load domain access register */ - - /* Set the TTB register */ - ldr r0, _mmu_table_base - ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE - ldr r2, =0xfff00000 - bic r0, r0, r2 - orr r1, r0, r1 - mcr p15, 0, r1, c2, c0, 0 - - /* Enable the MMU */ - mrc p15, 0, r0, c1, c0, 0 - orr r0, r0, #1 /* Set CR_M to enable MMU */ - - /* Prepare to enable the MMU */ - adr r1, skip_hw_init - and r1, r1, #0x3fc - ldr r2, _TEXT_BASE - ldr r3, =0xfff00000 - and r2, r2, r3 - orr r2, r2, r1 - b mmu_enable - - .align 5 - /* Run in a single cache-line */ -mmu_enable: - - mcr p15, 0, r0, c1, c0, 0 - nop - nop - mov pc, r2 -skip_hw_init: -#endif - relocate_done: bx lr @@ -347,11 +298,6 @@ _rel_dyn_end_ofs: _dynsym_start_ofs: .word __dynsym_start - _start -#ifdef CONFIG_ENABLE_MMU -_mmu_table_base: - .word mmu_table -#endif - .globl c_runtime_cpu_setup c_runtime_cpu_setup: @@ -359,41 +305,6 @@ c_runtime_cpu_setup: #ifndef CONFIG_SPL_BUILD /* - * we assume that cache operation is done before. (eg. cleanup_before_linux()) - * actually, we don't need to do anything about cache if not use d-cache in - * U-Boot. So, in this function we clean only MMU. by scsuh - * - * void theLastJump(void *kernel, int arch_num, uint boot_params); - */ -#ifdef CONFIG_ENABLE_MMU - .globl theLastJump -theLastJump: - mov r9, r0 - ldr r3, =0xfff00000 - ldr r4, _TEXT_PHY_BASE - adr r5, phy_last_jump - bic r5, r5, r3 - orr r5, r5, r4 - mov pc, r5 -phy_last_jump: - /* - * disable MMU stuff - */ - mrc p15, 0, r0, c1, c0, 0 - bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */ - bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */ - orr r0, r0, #0x00000002 /* set bit 2 (A) Align */ - orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */ - mcr p15, 0, r0, c1, c0, 0 - - mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ - - mov r0, #0 - mov pc, r9 -#endif - - -/* ************************************************************************* * * Interrupt handling |