summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/cpu/pxa/cpu.c229
-rw-r--r--arch/arm/cpu/pxa/start.S344
2 files changed, 359 insertions, 214 deletions
diff --git a/arch/arm/cpu/pxa/cpu.c b/arch/arm/cpu/pxa/cpu.c
index 330d013c6..3ea34582e 100644
--- a/arch/arm/cpu/pxa/cpu.c
+++ b/arch/arm/cpu/pxa/cpu.c
@@ -30,11 +30,11 @@
* CPU specific code
*/
-#include <asm/arch/pxa-regs.h>
#include <asm/io.h>
#include <asm/system.h>
#include <command.h>
#include <common.h>
+#include <asm/arch/pxa-regs.h>
static void cache_flush(void);
@@ -91,3 +91,230 @@ void set_GPIO_mode(int gpio_mode)
writel(val, GAFR(gpio));
}
#endif /* CONFIG_CPU_MONAHANS */
+
+void pxa_wait_ticks(int ticks)
+{
+ writel(0, OSCR);
+ while (readl(OSCR) < ticks)
+ asm volatile("":::"memory");
+}
+
+inline void writelrb(uint32_t val, uint32_t addr)
+{
+ writel(val, addr);
+ asm volatile("":::"memory");
+ readl(addr);
+ asm volatile("":::"memory");
+}
+
+void pxa_dram_init(void)
+{
+ uint32_t tmp;
+ int i;
+ /*
+ * 1) Initialize Asynchronous static memory controller
+ */
+
+ writelrb(CONFIG_SYS_MSC0_VAL, MSC0);
+ writelrb(CONFIG_SYS_MSC1_VAL, MSC1);
+ writelrb(CONFIG_SYS_MSC2_VAL, MSC2);
+ /*
+ * 2) Initialize Card Interface
+ */
+
+ /* MECR: Memory Expansion Card Register */
+ writelrb(CONFIG_SYS_MECR_VAL, MECR);
+ /* MCMEM0: Card Interface slot 0 timing */
+ writelrb(CONFIG_SYS_MCMEM0_VAL, MCMEM0);
+ /* MCMEM1: Card Interface slot 1 timing */
+ writelrb(CONFIG_SYS_MCMEM1_VAL, MCMEM1);
+ /* MCATT0: Card Interface Attribute Space Timing, slot 0 */
+ writelrb(CONFIG_SYS_MCATT0_VAL, MCATT0);
+ /* MCATT1: Card Interface Attribute Space Timing, slot 1 */
+ writelrb(CONFIG_SYS_MCATT1_VAL, MCATT1);
+ /* MCIO0: Card Interface I/O Space Timing, slot 0 */
+ writelrb(CONFIG_SYS_MCIO0_VAL, MCIO0);
+ /* MCIO1: Card Interface I/O Space Timing, slot 1 */
+ writelrb(CONFIG_SYS_MCIO1_VAL, MCIO1);
+
+ /*
+ * 3) Configure Fly-By DMA register
+ */
+
+ writelrb(CONFIG_SYS_FLYCNFG_VAL, FLYCNFG);
+
+ /*
+ * 4) Initialize Timing for Sync Memory (SDCLK0)
+ */
+
+ /*
+ * Before accessing MDREFR we need a valid DRI field, so we set
+ * this to power on defaults + DRI field.
+ */
+
+ /* Read current MDREFR config and zero out DRI */
+ tmp = readl(MDREFR) & ~0xfff;
+ /* Add user-specified DRI */
+ tmp |= CONFIG_SYS_MDREFR_VAL & 0xfff;
+ /* Configure important bits */
+ tmp |= MDREFR_K0RUN | MDREFR_SLFRSH;
+ tmp &= ~(MDREFR_APD | MDREFR_E1PIN);
+
+ /* Write MDREFR back */
+ writelrb(tmp, MDREFR);
+
+ /*
+ * 5) Initialize Synchronous Static Memory (Flash/Peripherals)
+ */
+
+ /* Initialize SXCNFG register. Assert the enable bits.
+ *
+ * Write SXMRS to cause an MRS command to all enabled banks of
+ * synchronous static memory. Note that SXLCR need not be written
+ * at this time.
+ */
+ writelrb(CONFIG_SYS_SXCNFG_VAL, SXCNFG);
+
+ /*
+ * 6) Initialize SDRAM
+ */
+
+ writelrb(CONFIG_SYS_MDREFR_VAL & ~MDREFR_SLFRSH, MDREFR);
+ writelrb(CONFIG_SYS_MDREFR_VAL | MDREFR_E1PIN, MDREFR);
+
+ /*
+ * 7) Write MDCNFG with MDCNFG:DEx deasserted (set to 0), to configure
+ * but not enable each SDRAM partition pair.
+ */
+
+ writelrb(CONFIG_SYS_MDCNFG_VAL &
+ ~(MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3), MDCNFG);
+ /* Wait for the clock to the SDRAMs to stabilize, 100..200 usec. */
+ pxa_wait_ticks(0x300);
+
+ /*
+ * 8) Trigger a number (usually 8) refresh cycles by attempting
+ * non-burst read or write accesses to disabled SDRAM, as commonly
+ * specified in the power up sequence documented in SDRAM data
+ * sheets. The address(es) used for this purpose must not be
+ * cacheable.
+ */
+ for (i = 9; i >= 0; i--) {
+ writel(i, 0xa0000000);
+ asm volatile("":::"memory");
+ }
+ /*
+ * 9) Write MDCNFG with enable bits asserted (MDCNFG:DEx set to 1).
+ */
+
+ tmp = CONFIG_SYS_MDCNFG_VAL &
+ (MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3);
+ tmp |= readl(MDCNFG);
+ writelrb(tmp, MDCNFG);
+
+ /*
+ * 10) Write MDMRS.
+ */
+
+ writelrb(CONFIG_SYS_MDMRS_VAL, MDMRS);
+
+ /*
+ * 11) Enable APD
+ */
+
+ if (CONFIG_SYS_MDREFR_VAL & MDREFR_APD) {
+ tmp = readl(MDREFR);
+ tmp |= MDREFR_APD;
+ writelrb(tmp, MDREFR);
+ }
+}
+
+void pxa_gpio_setup(void)
+{
+ writel(CONFIG_SYS_GPSR0_VAL, GPSR0);
+ writel(CONFIG_SYS_GPSR1_VAL, GPSR1);
+ writel(CONFIG_SYS_GPSR2_VAL, GPSR2);
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ writel(CONFIG_SYS_GPSR3_VAL, GPSR3);
+#endif
+
+ writel(CONFIG_SYS_GPCR0_VAL, GPCR0);
+ writel(CONFIG_SYS_GPCR1_VAL, GPCR1);
+ writel(CONFIG_SYS_GPCR2_VAL, GPCR2);
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ writel(CONFIG_SYS_GPCR3_VAL, GPCR3);
+#endif
+
+ writel(CONFIG_SYS_GPDR0_VAL, GPDR0);
+ writel(CONFIG_SYS_GPDR1_VAL, GPDR1);
+ writel(CONFIG_SYS_GPDR2_VAL, GPDR2);
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ writel(CONFIG_SYS_GPDR3_VAL, GPDR3);
+#endif
+
+ writel(CONFIG_SYS_GAFR0_L_VAL, GAFR0_L);
+ writel(CONFIG_SYS_GAFR0_U_VAL, GAFR0_U);
+ writel(CONFIG_SYS_GAFR1_L_VAL, GAFR1_L);
+ writel(CONFIG_SYS_GAFR1_U_VAL, GAFR1_U);
+ writel(CONFIG_SYS_GAFR2_L_VAL, GAFR2_L);
+ writel(CONFIG_SYS_GAFR2_U_VAL, GAFR2_U);
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ writel(CONFIG_SYS_GAFR3_L_VAL, GAFR3_L);
+ writel(CONFIG_SYS_GAFR3_U_VAL, GAFR3_U);
+#endif
+
+ writel(CONFIG_SYS_PSSR_VAL, PSSR);
+}
+
+void pxa_interrupt_setup(void)
+{
+ writel(0, ICLR);
+ writel(0, ICMR);
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ writel(0, ICLR2);
+ writel(0, ICMR2);
+#endif
+}
+
+void pxa_clock_setup(void)
+{
+#ifndef CONFIG_CPU_MONAHANS
+ writel(CONFIG_SYS_CKEN, CKEN);
+ writel(CONFIG_SYS_CCCR, CCCR);
+ asm volatile("mcr p14, 0, %0, c6, c0, 0"::"r"(2));
+#else
+/* Set CKENA/CKENB/ACCR for MH */
+#endif
+
+ /* enable the 32Khz oscillator for RTC and PowerManager */
+ writel(OSCC_OON, OSCC);
+ while(!(readl(OSCC) & OSCC_OOK))
+ asm volatile("":::"memory");
+}
+
+void pxa_wakeup(void)
+{
+ uint32_t rcsr;
+
+ rcsr = readl(RCSR);
+ writel(rcsr & (RCSR_GPR | RCSR_SMR | RCSR_WDR | RCSR_HWR), RCSR);
+
+ /* Wakeup */
+ if (rcsr & RCSR_SMR) {
+ writel(PSSR_PH, PSSR);
+ pxa_dram_init();
+ icache_disable();
+ dcache_disable();
+ asm volatile("mov pc, %0"::"r"(readl(PSSR)));
+ }
+}
+
+int arch_cpu_init(void)
+{
+ pxa_gpio_setup();
+// pxa_wait_ticks(0x8000);
+ pxa_wakeup();
+ pxa_interrupt_setup();
+ pxa_clock_setup();
+ return 0;
+}
diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S
index 9c5023bae..684e44e83 100644
--- a/arch/arm/cpu/pxa/start.S
+++ b/arch/arm/cpu/pxa/start.S
@@ -31,6 +31,14 @@
#include <config.h>
#include <version.h>
#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+/* takes care the CP15 update has taken place */
+.macro CPWAIT reg
+mrc p15,0,\reg,c2,c0,0
+mov \reg,\reg
+sub pc,pc,#4
+.endm
.globl _start
_start: b reset
@@ -86,11 +94,9 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
.globl _armboot_start
_armboot_start:
.word _start
-#endif
/*
* These are defined in the board-specific linker script.
@@ -115,7 +121,7 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif /* CONFIG_USE_IRQ */
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
+#ifndef CONFIG_PRELOADER
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -159,12 +165,84 @@ reset:
msr cpsr,r0
/*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
+ * Enable MMU to use DCache as DRAM
*/
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
+ /* Domain access -- enable for all CPs */
+ ldr r0, =0x0000ffff
+ mcr p15, 0, r0, c3, c0, 0
+
+ /* Point TTBR to MMU table */
+ ldr r0, =mmu_table
+ adr r2, _start
+ orr r0, r2
+ mcr p15, 0, r0, c2, c0, 0
+
+/* !!! Hereby, check if the code is running from SRAM !!! */
+/* If the code is running from SRAM, alias SRAM to 0x0 to simulate NOR. The code
+ * is linked to 0x0 too, so this makes things easier. */
+ cmp r2, #0x5c000000
+
+ ldreq r1, [r0]
+ orreq r1, r2
+ streq r1, [r0]
+
+ /* Kick in MMU, ICache, DCache, BTB */
+ mrc p15, 0, r0, c1, c0, 0
+ bic r0, #0x1b00
+ bic r0, #0x0087
+ orr r0, #0x1800
+ orr r0, #0x0005
+ mcr p15, 0, r0, c1, c0, 0
+ CPWAIT r0
+
+ /* Unlock Icache, Dcache */
+ mcr p15, 0, r0, c9, c1, 1
+ mcr p15, 0, r0, c9, c2, 1
+
+ /* Flush Icache, Dcache, BTB */
+ mcr p15, 0, r0, c7, c7, 0
+
+ /* Unlock I-TLB, D-TLB */
+ mcr p15, 0, r0, c10, c4, 1
+ mcr p15, 0, r0, c10, c8, 1
+
+ /* Flush TLB */
+ mcr p15, 0, r0, c8, c7, 0
+ /* Allocate 4096 bytes of Dcache as RAM */
+
+ /* Drain pending loads and stores */
+ mcr p15, 0, r0, c7, c10, 4
+
+ mov r4, #0x00
+ mov r5, #0x00
+ mov r2, #0x01
+ mcr p15, 0, r0, c9, c2, 0
+ CPWAIT r0
+
+ /* 128 lines reserved (128 x 32bytes = 4096 bytes total) */
+ mov r0, #128
+ mov r1, #0xa0000000
+alloc:
+ mcr p15, 0, r1, c7, c2, 5
+ /* Drain pending loads and stores */
+ mcr p15, 0, r0, c7, c10, 4
+ strd r4, [r1], #8
+ strd r4, [r1], #8
+ strd r4, [r1], #8
+ strd r4, [r1], #8
+ subs r0, #0x01
+ bne alloc
+ /* Drain pending loads and stores */
+ mcr p15, 0, r0, c7, c10, 4
+ mov r2, #0x00
+ mcr p15, 0, r2, c9, c2, 0
+ CPWAIT r0
+
+ /* Jump to 0x0 ( + offset) if running from SRAM */
+ adr r0, zerojmp
+ bic r0, #0x5c000000
+ mov pc, r0
+zerojmp:
/* Set stackpointer in internal RAM to call board_init_f */
call_board_init_f:
@@ -201,11 +279,13 @@ stack_setup:
beq clear_bss
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
+ stmfd sp!, {r0-r12}
copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r6!, {r9-r10} /* copy to target address [r1] */
+ ldmia r0!, {r3-r5, r7-r11} /* copy from source address [r0] */
+ stmia r6!, {r3-r5, r7-r11} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
+ ldmfd sp!, {r0-r12}
#ifndef CONFIG_PRELOADER
/* fix got entries */
@@ -274,218 +354,28 @@ _board_init_r: .word board_init_r
/****************************************************************************/
/* */
-/* the actual reset code */
+/* the actual reset code for OneNAND IPL */
/* */
/****************************************************************************/
+#ifndef CONFIG_PXA27X
+#error OneNAND IPL is not supported on PXA25x and 26x due to lack of SRAM
+#endif
+
reset:
- mrs r0,cpsr /* set the CPU to SVC32 mode */
- bic r0,r0,#0x1f /* (superviser mode, M=10011) */
+ /* Set CPU to SVC32 mode */
+ mrs r0,cpsr
+ bic r0,r0,#0x1f
orr r0,r0,#0x13
msr cpsr,r0
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from RAM!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit /* we do sys-critical inits */
-#endif /* !CONFIG_SKIP_LOWLEVEL_INIT */
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
-#ifndef CONFIG_PRELOADER
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-#endif
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* !CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
-#ifdef CONFIG_PRELOADER
- sub sp, r0, #128 /* leave 32 words for abort-stack */
-#else
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif /* CONFIG_USE_IRQ */
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-#endif
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-#ifndef CONFIG_PRELOADER
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-#endif
-
- ldr pc, _start_armboot
-
-#ifdef CONFIG_ONENAND_IPL
-_start_armboot: .word start_oneboot
-#else
-_start_armboot: .word start_armboot
-#endif
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
-/****************************************************************************/
-/* */
-/* CPU_init_critical registers */
-/* */
-/* - setup important registers */
-/* - setup memory timing */
-/* */
-/****************************************************************************/
-/* mk@tbd: Fix this! */
-#undef RCSR
-#undef ICMR
-#undef OSMR3
-#undef OSCR
-#undef OWER
-#undef OIER
-#undef CCCR
-
-/* Interrupt-Controller base address */
-IC_BASE: .word 0x40d00000
-#define ICMR 0x04
-
-/* Reset-Controller */
-RST_BASE: .word 0x40f00030
-#define RCSR 0x00
-
-/* Operating System Timer */
-OSTIMER_BASE: .word 0x40a00000
-#define OSMR3 0x0C
-#define OSCR 0x10
-#define OWER 0x18
-#define OIER 0x1C
-
-/* Clock Manager Registers */
-#ifdef CONFIG_CPU_MONAHANS
-# ifndef CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
-# error "You have to define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO!!"
-# endif /* !CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO */
-# ifndef CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
-# define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO 0x1
-# endif /* !CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO */
-#else /* !CONFIG_CPU_MONAHANS */
-#ifdef CONFIG_SYS_CPUSPEED
-CC_BASE: .word 0x41300000
-#define CCCR 0x00
-cpuspeed: .word CONFIG_SYS_CPUSPEED
-#else /* !CONFIG_SYS_CPUSPEED */
-#error "You have to define CONFIG_SYS_CPUSPEED!!"
-#endif /* CONFIG_SYS_CPUSPEED */
-#endif /* CONFIG_CPU_MONAHANS */
-
- /* takes care the CP15 update has taken place */
- .macro CPWAIT reg
- mrc p15,0,\reg,c2,c0,0
- mov \reg,\reg
- sub pc,pc,#4
- .endm
-
-cpu_init_crit:
-
- /* mask all IRQs */
-#ifndef CONFIG_CPU_MONAHANS
- ldr r0, IC_BASE
- mov r1, #0x00
- str r1, [r0, #ICMR]
-#else /* CONFIG_CPU_MONAHANS */
- /* Step 1 - Enable CP6 permission */
- mrc p15, 0, r1, c15, c1, 0 @ read CPAR
- orr r1, r1, #0x40
- mcr p15, 0, r1, c15, c1, 0
- CPWAIT r1
-
- /* Step 2 - Mask ICMR & ICMR2 */
- mov r1, #0
- mcr p6, 0, r1, c1, c0, 0 @ ICMR
- mcr p6, 0, r1, c7, c0, 0 @ ICMR2
+ /* Point stack at the end of SRAM and leave 32 words for abort-stack */
+ ldr sp, =0x5c03ff80
- /* turn off all clocks but the ones we will definitly require */
- ldr r1, =CKENA
- ldr r2, =(CKENA_22_FFUART | CKENA_10_SRAM | CKENA_9_SMC | CKENA_8_DMC)
- str r2, [r1]
- ldr r1, =CKENB
- ldr r2, =(CKENB_6_IRQ)
- str r2, [r1]
-#endif /* !CONFIG_CPU_MONAHANS */
+ /* Start OneNAND IPL */
+ ldr pc, =start_oneboot
- /* set clock speed */
-#ifdef CONFIG_CPU_MONAHANS
- ldr r0, =ACCR
- ldr r1, =(((CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO<<8) & ACCR_XN_MASK) | (CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO & ACCR_XL_MASK))
- str r1, [r0]
-#else /* !CONFIG_CPU_MONAHANS */
-#ifdef CONFIG_SYS_CPUSPEED
- ldr r0, CC_BASE
- ldr r1, cpuspeed
- str r1, [r0, #CCCR]
- mov r0, #2
- mcr p14, 0, r0, c6, c0, 0
-
-setspeed_done:
-
-#endif /* CONFIG_SYS_CPUSPEED */
-#endif /* CONFIG_CPU_MONAHANS */
-
- /*
- * before relocating, we have to setup RAM timing
- * because memory timing is board-dependend, you will
- * find a lowlevel_init.S in your board directory.
- */
- mov ip, lr
- bl lowlevel_init
- mov lr, ip
-
- /* Memory interfaces are working. Disable MMU and enable I-cache. */
- /* mk: hmm, this is not in the monahans docs, leave it now but
- * check here if it doesn't work :-) */
-
- ldr r0, =0x2001 /* enable access to all coproc. */
- mcr p15, 0, r0, c15, c1, 0
- CPWAIT r0
-
- mcr p15, 0, r0, c7, c10, 4 /* drain the write & fill buffers */
- CPWAIT r0
-
- mcr p15, 0, r0, c7, c7, 0 /* flush Icache, Dcache and BTB */
- CPWAIT r0
-
- mcr p15, 0, r0, c8, c7, 0 /* flush instuction and data TLBs */
- CPWAIT r0
-
- /* Enable the Icache */
-/*
- mrc p15, 0, r0, c1, c0, 0
- orr r0, r0, #0x1800
- mcr p15, 0, r0, c1, c0, 0
- CPWAIT
-*/
- mov pc, lr
+#endif /* #if !defined(CONFIG_ONENAND_IPL) */
#ifndef CONFIG_PRELOADER
/****************************************************************************/
@@ -676,6 +566,12 @@ fiq:
/* perform a watchdog timeout for a soft reset. */
/* */
/****************************************************************************/
+/* Operating System Timer */
+OSTIMER_BASE: .word 0x40a00000
+#define OSMR3 0x0C
+#define OSCR 0x10
+#define OWER 0x18
+#define OIER 0x1C
.align 5
.globl reset_cpu
@@ -703,3 +599,25 @@ reset_cpu:
reset_endless:
b reset_endless
+
+#ifndef CONFIG_PRELOADER
+.section .mmudata, "a"
+ .align 14
+ .globl mmu_table
+mmu_table:
+ /* 0x00000000 - 0xa0000000 : 1:1, uncached mapping */
+ .set __base, 0
+ .rept 0xa00
+ .word (__base << 20) | 0xc12
+ .set __base, __base + 1
+ .endr
+
+ /* 0xa0000000 - 0xa0100000 : 1:1, cached mapping */
+ .word (0xa00 << 20) | 0x1c1e
+
+ .set __base, 0xa01
+ .rept 0x1000 - 0xa01
+ .word (__base << 20) | 0xc12
+ .set __base, __base + 1
+ .endr
+#endif
generated by cgit v1.2.3-70-g09d2 (git 2.51.2) at 2025-10-31 05:42:15 +0000