diff options
| -rw-r--r-- | README | 6 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu.c | 4 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc8xxx/ddr/Makefile | 13 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc8xxx/ddr/ddr.h | 7 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc8xxx/ddr/main.c | 12 |
5 files changed, 39 insertions, 3 deletions
@@ -2948,6 +2948,12 @@ Low Level (hardware related) configuration options: one, specify here. Note that the value must resolve to something your driver can deal with. +- CONFIG_SYS_DDR_RAW_TIMING + Get DDR timing information from other than SPD. Common with + soldered DDR chips onboard without SPD. DDR raw timing + parameters are extracted from datasheet and hard-coded into + header files or board specific files. + - CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3. diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index f863f4aad..53f088791 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -336,7 +336,9 @@ phys_size_t initdram(int board_type) } #endif -#if defined(CONFIG_SPD_EEPROM) || defined(CONFIG_DDR_SPD) +#if defined(CONFIG_SPD_EEPROM) || \ + defined(CONFIG_DDR_SPD) || \ + defined(CONFIG_SYS_DDR_RAW_TIMING) dram_size = fsl_ddr_sdram(); #else dram_size = fixed_sdram(); diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/Makefile b/arch/powerpc/cpu/mpc8xxx/ddr/Makefile index 4a5a78558..d1b4c4b47 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/Makefile +++ b/arch/powerpc/cpu/mpc8xxx/ddr/Makefile @@ -12,15 +12,24 @@ LIB = $(obj)libddr.o COBJS-$(CONFIG_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \ lc_common_dimm_params.o -COBJS-$(CONFIG_FSL_DDR1) += ddr1_dimm_params.o COBJS-$(CONFIG_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \ lc_common_dimm_params.o -COBJS-$(CONFIG_FSL_DDR2) += ddr2_dimm_params.o COBJS-$(CONFIG_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \ lc_common_dimm_params.o +ifdef CONFIG_DDR_SPD +SPD := y +endif +ifdef CONFIG_SPD_EEPROM +SPD := y +endif +ifdef SPD +COBJS-$(CONFIG_FSL_DDR1) += ddr1_dimm_params.o +COBJS-$(CONFIG_FSL_DDR2) += ddr2_dimm_params.o COBJS-$(CONFIG_FSL_DDR3) += ddr3_dimm_params.o +endif + SRCS := $(START:.o=.S) $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y)) diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h b/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h index 1e866fe03..f59aa33b2 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h +++ b/arch/powerpc/cpu/mpc8xxx/ddr/ddr.h @@ -14,6 +14,7 @@ #include "common_timing_params.h" +#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM) /* * Bind the main DDR setup driver's generic names * to this specific DDR technology. @@ -25,6 +26,7 @@ compute_dimm_parameters(const generic_spd_eeprom_t *spd, { return ddr_compute_dimm_parameters(spd, pdimm, dimm_number); } +#endif /* * Data Structures @@ -80,4 +82,9 @@ extern void check_interleaving_options(fsl_ddr_info_t *pinfo); extern unsigned int mclk_to_picos(unsigned int mclk); extern unsigned int get_memory_clk_period_ps(void); extern unsigned int picos_to_mclk(unsigned int picos); + +/* board specific function */ +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number); #endif diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/main.c b/arch/powerpc/cpu/mpc8xxx/ddr/main.c index 62a73ddf4..3c49fa97c 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/main.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/main.c @@ -325,6 +325,7 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, switch (start_step) { case STEP_GET_SPD: +#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM) /* STEP 1: Gather all DIMM SPD data */ for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { fsl_ddr_get_spd(pinfo->spd_installed_dimms[i], i); @@ -356,6 +357,17 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, } } +#else + case STEP_COMPUTE_DIMM_PARMS: + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + dimm_params_t *pdimm = + &(pinfo->dimm_params[i][j]); + fsl_ddr_get_dimm_params(pdimm, i, j); + } + } + debug("Filling dimm parameters from board specific file\n"); +#endif case STEP_COMPUTE_COMMON_PARMS: /* * STEP 3: Compute a common set of timing parameters |