Pass sdrc timing values through board_sdrc_timings structure

Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings.  This saves about
90 bytes of space in SPL.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>

9 files changed, 120 insertions, 122 deletions

diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
index f6d9b97bb..e32bf118b 100644
--- a/arch/arm/cpu/armv7/omap3/sdrc.c
+++ b/arch/arm/cpu/armv7/omap3/sdrc.c
@@ -113,18 +113,18 @@ u32 get_sdr_cs_offset(u32 cs)
  *  - Test CS to make sure it's OK for use
  */
 static void write_sdrc_timings(u32 cs, struct sdrc_actim *sdrc_actim_base,
-		u32 mcfg, u32 ctrla, u32 ctrlb, u32 rfr_ctrl, u32 mr)
+			struct board_sdrc_timings *timings)
 {
 	/* Setup timings we got from the board. */
-	writel(mcfg, &sdrc_base->cs[cs].mcfg);
-	writel(ctrla, &sdrc_actim_base->ctrla);
-	writel(ctrlb, &sdrc_actim_base->ctrlb);
-	writel(rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
+	writel(timings->mcfg, &sdrc_base->cs[cs].mcfg);
+	writel(timings->ctrla, &sdrc_actim_base->ctrla);
+	writel(timings->ctrlb, &sdrc_actim_base->ctrlb);
+	writel(timings->rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
 	writel(CMD_NOP, &sdrc_base->cs[cs].manual);
 	writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
 	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
 	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-	writel(mr, &sdrc_base->cs[cs].mr);
+	writel(timings->mr, &sdrc_base->cs[cs].mr);
 
 	/*
 	 * Test ram in this bank
@@ -143,7 +143,7 @@ static void write_sdrc_timings(u32 cs, struct sdrc_actim *sdrc_actim_base,
 void do_sdrc_init(u32 cs, u32 early)
 {
 	struct sdrc_actim *sdrc_actim_base0, *sdrc_actim_base1;
-	u32 mcfg, ctrla, ctrlb, rfr_ctrl, mr;
+	struct board_sdrc_timings timings;
 
 	sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
 	sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
@@ -158,7 +158,7 @@ void do_sdrc_init(u32 cs, u32 early)
 	 * setup CS1.
 	 */
 #ifdef CONFIG_SPL_BUILD
-	get_board_mem_timings(&mcfg, &ctrla, &ctrlb, &rfr_ctrl, &mr);
+	get_board_mem_timings(&timings);
 #endif
 	if (early) {
 		/* reset sdrc controller */
@@ -177,11 +177,9 @@ void do_sdrc_init(u32 cs, u32 early)
 		writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
 		sdelay(0x20000);
 #ifdef CONFIG_SPL_BUILD
-		write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
-				rfr_ctrl, mr);
+		write_sdrc_timings(CS0, sdrc_actim_base0, &timings);
 		make_cs1_contiguous();
-		write_sdrc_timings(CS1, sdrc_actim_base1, mcfg, ctrla, ctrlb,
-				rfr_ctrl, mr);
+		write_sdrc_timings(CS1, sdrc_actim_base1, &timings);
 #endif
 
 	}
@@ -193,14 +191,12 @@ void do_sdrc_init(u32 cs, u32 early)
 	 * so we may be asked now to setup CS1.
 	 */
 	if (cs == CS1) {
-		mcfg = readl(&sdrc_base->cs[CS0].mcfg),
-		rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
-		ctrla = readl(&sdrc_actim_base0->ctrla),
-		ctrlb = readl(&sdrc_actim_base0->ctrlb);
-		mr = readl(&sdrc_base->cs[CS0].mr);
-		write_sdrc_timings(cs, sdrc_actim_base1, mcfg, ctrla, ctrlb,
-				rfr_ctrl, mr);
-
+		timings.mcfg = readl(&sdrc_base->cs[CS0].mcfg),
+		timings.rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
+		timings.ctrla = readl(&sdrc_actim_base0->ctrla);
+		timings.ctrlb = readl(&sdrc_actim_base0->ctrlb);
+		timings.mr = readl(&sdrc_base->cs[CS0].mr);
+		write_sdrc_timings(cs, sdrc_actim_base1, &timings);
 	}
 }
 
diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
index 9e52b12aa..d60f2addb 100644
--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
@@ -32,6 +32,15 @@ struct emu_hal_params {
 	u32 param1;
 };
 
+/* Board SDRC timing values */
+struct board_sdrc_timings {
+	u32 mcfg;
+	u32 ctrla;
+	u32 ctrlb;
+	u32 rfr_ctrl;
+	u32 mr;
+};
+
 void prcm_init(void);
 void per_clocks_enable(void);
 void ehci_clocks_enable(void);
@@ -39,8 +48,8 @@ void ehci_clocks_enable(void);
 void memif_init(void);
 void sdrc_init(void);
 void do_sdrc_init(u32, u32);
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr);
+
+void get_board_mem_timings(struct board_sdrc_timings *timings);
 void identify_nand_chip(int *mfr, int *id);
 void emif4_init(void);
 void gpmc_init(void);
diff --git a/board/corscience/tricorder/tricorder.c b/board/corscience/tricorder/tricorder.c
index aaff2e868..56fe49527 100644
--- a/board/corscience/tricorder/tricorder.c
+++ b/board/corscience/tricorder/tricorder.c
@@ -91,15 +91,14 @@ int board_mmc_init(bd_t *bis)
  * provides the timing values back to the function that configures
  * the memory.  We have either one or two banks of 128MB DDR.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-				u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
 	/* General SDRC config */
-	*mcfg = MICRON_V_MCFG_165(128 << 20);
-	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 
 	/* AC timings */
-	*ctrla = MICRON_V_ACTIMA_165;
-	*ctrlb = MICRON_V_ACTIMB_165;
-	*mr = MICRON_V_MR_165;
+	timings->ctrla = MICRON_V_ACTIMA_165;
+	timings->ctrlb = MICRON_V_ACTIMB_165;
+	timings->mr = MICRON_V_MR_165;
 }
diff --git a/board/isee/igep0020/igep0020.c b/board/isee/igep0020/igep0020.c
index a8257a300..a0f2aa3e4 100644
--- a/board/isee/igep0020/igep0020.c
+++ b/board/isee/igep0020/igep0020.c
@@ -72,27 +72,26 @@ void omap_rev_string(void)
  * Description: If we use SPL then there is no x-loader nor config header
  * so we have to setup the DDR timings ourself on both banks.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
-	*mr = MICRON_V_MR_165;
+	timings->mr = MICRON_V_MR_165;
 #ifdef CONFIG_BOOT_NAND
-	*mcfg = MICRON_V_MCFG_200(256 << 20);
-	*ctrla = MICRON_V_ACTIMA_200;
-	*ctrlb = MICRON_V_ACTIMB_200;
-	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+	timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+	timings->ctrla = MICRON_V_ACTIMA_200;
+	timings->ctrlb = MICRON_V_ACTIMB_200;
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 #else
 	if (get_cpu_family() == CPU_OMAP34XX) {
-		*mcfg = NUMONYX_V_MCFG_165(256 << 20);
-		*ctrla = NUMONYX_V_ACTIMA_165;
-		*ctrlb = NUMONYX_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
+		timings->ctrla = NUMONYX_V_ACTIMA_165;
+		timings->ctrlb = NUMONYX_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 
 	} else {
-		*mcfg = NUMONYX_V_MCFG_200(256 << 20);
-		*ctrla = NUMONYX_V_ACTIMA_200;
-		*ctrlb = NUMONYX_V_ACTIMB_200;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+		timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
+		timings->ctrla = NUMONYX_V_ACTIMA_200;
+		timings->ctrlb = NUMONYX_V_ACTIMB_200;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 	}
 #endif
 }
diff --git a/board/isee/igep0030/igep0030.c b/board/isee/igep0030/igep0030.c
index 107cb7f8e..a41e752b8 100644
--- a/board/isee/igep0030/igep0030.c
+++ b/board/isee/igep0030/igep0030.c
@@ -59,27 +59,26 @@ void omap_rev_string(void)
  * Description: If we use SPL then there is no x-loader nor config header
  * so we have to setup the DDR timings ourself on both banks.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-			   u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
-	*mr = MICRON_V_MR_165;
+	timings->mr = MICRON_V_MR_165;
 #ifdef CONFIG_BOOT_NAND
-	*mcfg = MICRON_V_MCFG_200(256 << 20);
-	*ctrla = MICRON_V_ACTIMA_200;
-	*ctrlb = MICRON_V_ACTIMB_200;
-	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+	timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+	timings->ctrla = MICRON_V_ACTIMA_200;
+	timings->ctrlb = MICRON_V_ACTIMB_200;
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 #else
 	if (get_cpu_family() == CPU_OMAP34XX) {
-		*mcfg = NUMONYX_V_MCFG_165(256 << 20);
-		*ctrla = NUMONYX_V_ACTIMA_165;
-		*ctrlb = NUMONYX_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
+		timings->ctrla = NUMONYX_V_ACTIMA_165;
+		timings->ctrlb = NUMONYX_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 
 	} else {
-		*mcfg = NUMONYX_V_MCFG_200(256 << 20);
-		*ctrla = NUMONYX_V_ACTIMA_200;
-		*ctrlb = NUMONYX_V_ACTIMB_200;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+		timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
+		timings->ctrla = NUMONYX_V_ACTIMA_200;
+		timings->ctrlb = NUMONYX_V_ACTIMB_200;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 	}
 #endif
 }
diff --git a/board/overo/overo.c b/board/overo/overo.c
index c6d50a07a..fdf46a2aa 100644
--- a/board/overo/overo.c
+++ b/board/overo/overo.c
@@ -147,34 +147,33 @@ int get_board_revision(void)
  * Description: If we use SPL then there is no x-loader nor config header
  * so we have to setup the DDR timings ourself on both banks.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
-	*mr = MICRON_V_MR_165;
+	timings->mr = MICRON_V_MR_165;
 	switch (get_board_revision()) {
 	case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */
-		*mcfg = MICRON_V_MCFG_165(128 << 20);
-		*ctrla = MICRON_V_ACTIMA_165;
-		*ctrlb = MICRON_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 		break;
 	case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
-		*mcfg = MICRON_V_MCFG_165(256 << 20);
-		*ctrla = MICRON_V_ACTIMA_165;
-		*ctrlb = MICRON_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = MICRON_V_MCFG_165(256 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 		break;
 	case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */
-		*mcfg = HYNIX_V_MCFG_165(256 << 20);
-		*ctrla = HYNIX_V_ACTIMA_165;
-		*ctrlb = HYNIX_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = HYNIX_V_MCFG_165(256 << 20);
+		timings->ctrla = HYNIX_V_ACTIMA_165;
+		timings->ctrlb = HYNIX_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 		break;
 	default:
-		*mcfg = MICRON_V_MCFG_165(128 << 20);
-		*ctrla = MICRON_V_ACTIMA_165;
-		*ctrlb = MICRON_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 	}
 }
 #endif
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 6175e1d1a..4adf9827c 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -139,8 +139,7 @@ static int get_board_revision(void)
  * Description: If we use SPL then there is no x-loader nor config header
  * so we have to setup the DDR timings ourself on both banks.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
 	int pop_mfr, pop_id;
 
@@ -151,29 +150,29 @@ void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
 	 */
 	identify_nand_chip(&pop_mfr, &pop_id);
 
-	*mr = MICRON_V_MR_165;
+	timings->mr = MICRON_V_MR_165;
 	switch (get_board_revision()) {
 	case REVISION_C4:
 		if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
 			/* 512MB DDR */
-			*mcfg = NUMONYX_V_MCFG_165(512 << 20);
-			*ctrla = NUMONYX_V_ACTIMA_165;
-			*ctrlb = NUMONYX_V_ACTIMB_165;
-			*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+			timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+			timings->ctrla = NUMONYX_V_ACTIMA_165;
+			timings->ctrlb = NUMONYX_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 			break;
 		} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xba) {
 			/* Beagleboard Rev C4, 512MB Nand/256MB DDR*/
-			*mcfg = MICRON_V_MCFG_165(128 << 20);
-			*ctrla = MICRON_V_ACTIMA_165;
-			*ctrlb = MICRON_V_ACTIMB_165;
-			*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+			timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_165;
+			timings->ctrlb = MICRON_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 			break;
 		} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
 			/* Beagleboard Rev C5, 256MB DDR */
-			*mcfg = MICRON_V_MCFG_200(256 << 20);
-			*ctrla = MICRON_V_ACTIMA_200;
-			*ctrlb = MICRON_V_ACTIMB_200;
-			*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+			timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_200;
+			timings->ctrlb = MICRON_V_ACTIMB_200;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 			break;
 		}
 	case REVISION_XM_A:
@@ -181,24 +180,24 @@ void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
 	case REVISION_XM_C:
 		if (pop_mfr == 0) {
 			/* 256MB DDR */
-			*mcfg = MICRON_V_MCFG_200(256 << 20);
-			*ctrla = MICRON_V_ACTIMA_200;
-			*ctrlb = MICRON_V_ACTIMB_200;
-			*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+			timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_200;
+			timings->ctrlb = MICRON_V_ACTIMB_200;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 		} else {
 			/* 512MB DDR */
-			*mcfg = NUMONYX_V_MCFG_165(512 << 20);
-			*ctrla = NUMONYX_V_ACTIMA_165;
-			*ctrlb = NUMONYX_V_ACTIMB_165;
-			*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+			timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+			timings->ctrla = NUMONYX_V_ACTIMA_165;
+			timings->ctrlb = NUMONYX_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 		}
 		break;
 	default:
 		/* Assume 128MB and Micron/165MHz timings to be safe */
-		*mcfg = MICRON_V_MCFG_165(128 << 20);
-		*ctrla = MICRON_V_ACTIMA_165;
-		*ctrlb = MICRON_V_ACTIMB_165;
-		*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 	}
 }
 #endif
diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c
index 61fc7b553..8a3aa0c5b 100644
--- a/board/ti/evm/evm.c
+++ b/board/ti/evm/evm.c
@@ -128,8 +128,7 @@ int board_init(void)
  * provides the timing values back to the function that configures
  * the memory.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
 	int pop_mfr, pop_id;
 
@@ -142,17 +141,17 @@ void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
 
 	if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) {
 		/* 256MB DDR */
-		*mcfg = HYNIX_V_MCFG_200(256 << 20);
-		*ctrla = HYNIX_V_ACTIMA_200;
-		*ctrlb = HYNIX_V_ACTIMB_200;
+		timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
+		timings->ctrla = HYNIX_V_ACTIMA_200;
+		timings->ctrlb = HYNIX_V_ACTIMB_200;
 	} else {
 		/* 128MB DDR */
-		*mcfg = MICRON_V_MCFG_165(128 << 20);
-		*ctrla = MICRON_V_ACTIMA_165;
-		*ctrlb = MICRON_V_ACTIMB_165;
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
 	}
-	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
-	*mr = MICRON_V_MR_165;
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	timings->mr = MICRON_V_MR_165;
 }
 #endif
 
diff --git a/board/timll/devkit8000/devkit8000.c b/board/timll/devkit8000/devkit8000.c
index 35f5e15fc..85685ee7c 100644
--- a/board/timll/devkit8000/devkit8000.c
+++ b/board/timll/devkit8000/devkit8000.c
@@ -188,16 +188,15 @@ int spl_start_uboot(void)
  * provides the timing values back to the function that configures
  * the memory.  We have either one or two banks of 128MB DDR.
  */
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
-		u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
 	/* General SDRC config */
-	*mcfg = MICRON_V_MCFG_165(128 << 20);
-	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 
 	/* AC timings */
-	*ctrla = MICRON_V_ACTIMA_165;
-	*ctrlb = MICRON_V_ACTIMB_165;
+	timings->ctrla = MICRON_V_ACTIMA_165;
+	timings->ctrlb = MICRON_V_ACTIMB_165;
 
-	*mr = MICRON_V_MR_165;
+	timings->mr = MICRON_V_MR_165;
 }