path: root/arch/arm/mach-omap2/board-omap3h1.c

/*
 * Copyright (C) 2014 Olio Devices, Inc.
 * Authors: Evan Wilson <evan@oliodevices.com>
 *			Mattis Fjallstrom <mattis@oliodevices.com>
 *
 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
 *
 * Modified from the original mach-omap/omap2/board-generic.c did by Paul
 * to support the OMAP2+ device tree boards with an unique board file.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/opp.h>
#include <linux/cpu.h>
#include <linux/mpu.h>
#include <linux/spi/spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>

#include <linux/usb/musb.h>
#include <linux/usb/phy.h>
#include <linux/usb/nop-usb-xceiv.h>

#include <linux/i2c/atmel_mxt_ts.h>
#include <linux/gpio.h>

#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/mfd/tps65910.h>

#include <linux/wakelock.h> /* used in interrupt, waking up.  */
#include <linux/debugfs.h>

#include <linux/led-lm3530.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>

#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include <linux/platform_data/serial-omap.h>
#include <linux/interrupt.h>

#include <linux/of_irq.h>
#include <linux/of_platform.h>


#include "common.h"
#include "omap_device.h"
#include "gpmc.h"
#include "soc.h"
#include "mux.h"
#include "pm.h"
#include "board-flash.h"
#include "common-board-devices.h"
#include "board-omap3h1.h"

#include "sdram-micron-mt29c8g96m-48.h"

#define NAND_CS 0

#define MPUIRQ_GPIO 31
#define ATMEL_MXT_GPIO 105
#define TPS_SYS_NIRQ 0
#define USB_IRQ 124
#define USB_CS 17

#define DEFAULT_RXDMA_POLLRATE		1	/* RX DMA polling rate (us) */
#define DEFAULT_RXDMA_BUFSIZE		4096	/* RX DMA buffer size */
#define DEFAULT_RXDMA_TIMEOUT		(3 * HZ)/* RX DMA timeout (jiffies) */

#if defined(CONFIG_MACH_OMAP3_H1_DVT1) || defined(CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
#define LCD_RESET_GPIO 94
#else 
#define LCD_RESET_GPIO 122
#endif

static struct of_device_id omap_dt_match_table[] __initdata = {
	{ .compatible = "olio,omap3-h1", },
	{ .compatible = "simple-bus", },
	{ .compatible = "ti,omap-infra", },
	{ }
};

static struct mtd_partition omap3h1_nand_partitions[] = {
	/* All the partition sizes are listed in terms of NAND block size */
	{
		.name		= "X-Loader",
		.offset		= 0,
		.size		= 4 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
		.size		= 15 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot Env",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
		.size		= 1 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "kernel",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
		.size		= 40 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "initramfs",
		.offset		= MTDPART_OFS_APPEND, 	/* Offset = 0xC80000 */
		.size		= 80 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "ramdisk",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x1180000 */
		.size		= 40 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "system",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x1680000 */
		.size		= 2000 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "userdata",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x11180000 */
		.size		= MTDPART_SIZ_FULL,
	},
};

static struct omap_dss_device omap3h1_lcd_device = {
	.type				= OMAP_DISPLAY_TYPE_DPI,
	.name				= "olio_h1_panel",
	.driver_name 		= "ili9342_panel",
	.phy.dpi.data_lines = 18,
	.reset_gpio			= LCD_RESET_GPIO,
};

static struct omap_dss_device *omap3h1_dss_devices[] = {
		&omap3h1_lcd_device,
};

static struct omap_dss_board_info omap3h1_dss_data = {
	.num_devices 	= 1,
	.devices = omap3h1_dss_devices,
	.default_device = &omap3h1_lcd_device,
};

static struct spi_board_info omap3h1_spi_board_info[] __initdata = {
	{
		.modalias		= "ili9342-spi",
		.bus_num		= 1,
		.chip_select 	= 1,
		.max_speed_hz 	= 375000,
		.platform_data	= &omap3h1_lcd_device,
		.mode			= SPI_MODE_0,
	}
};

static int __init omap3h1_spi_init(void) {
    spi_register_board_info(omap3h1_spi_board_info,
                            ARRAY_SIZE(omap3h1_spi_board_info));
    return 0;
}


/* 
 * int_config is interrupt config, INT_ENABLE register. To enable _all_ 
 * interrupts, set to 0x59. I think. --mfj
 * 
 * Level shifter seems to set power rail between two options - 1 means VDD.
 * (0 means VLogic, which I'm not sure what it is).
 */

#ifndef CONFIG_MACH_OMAP3_H1_PV2 
static struct mpu_platform_data mpu_data = {
	.int_config  = 0x00,
	.level_shifter = 1,
	.orientation = {  0, -1,  0,
					 -1,  0,  0,
					  0,  0,  1 },
};
#endif

static struct lm3530_platform_data omap3h1_backlight_platform_data = {
	.mode = LM3530_BL_MODE_MANUAL,
	//.als_input_mode = LM3530_INPUT_ALS1,
	.max_current = LM3530_FS_CURR_29mA,
	//.pwm_pol_hi = true,
	//.als_avrg_time = LM3530_ALS_AVRG_TIME_512ms,
	.brt_ramp_law = 0,
	.brt_ramp_fall = LM3530_RAMP_TIME_1s, /* LM3530_RAMP_TIME_1s, */
	.brt_ramp_rise = LM3530_RAMP_TIME_1s, /* LM3530_RAMP_TIME_1s, */
	//.als1_resistor_sel = LM3530_ALS_IMPD_13_53kOhm,
	//.als2_resistor_sel = LM3530_ALS_IMPD_Z,
	//.als_vmin = 730,	    /* mV */
	//.als_vmax = 10a20,	/* mV */
	.brt_val = 0x64,	/* initial brightness */
};



static struct mxt_platform_data mxt_data = {
    .irqflags	= IRQF_TRIGGER_FALLING,
}; 


static struct platform_device bcm20702_bluetooth_device = {
	.name = "bcm20702_bluetooth",
	.id   = -1,
};

static struct platform_device omap3h1_dmic_codec = {
		.name = "dmic-codec",
		.id = -1,
};

/* --------------------------------------------------------------------------- */
/* USB settings 
 */



static struct omap_musb_board_data musb_board_data = {
	.interface_type		= MUSB_INTERFACE_ULPI,
	.mode   			= MUSB_OTG,
	.power	    		= 100,
};

static struct nop_usb_xceiv_platform_data nop_plat_data = {
   .type     = USB_PHY_TYPE_USB2,
   .clk_rate = 60000000, /* 60 MHz */
   .needs_vcc = 1,
   .needs_reset = 0,
};

static struct platform_device nop_phy_device = {
  .name = "nop_usb_xceiv",
  .id   = -1,
  .dev  = {
      .platform_data = &nop_plat_data,
  },
};


/* static struct usbhs_omap_platform_data usbhs_bdata __initdata = { */
/* 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, */
/* }; */




/* ====================================================================== */


static struct i2c_board_info __initdata omap3h1_i2c1_board_info[] = {
         {
         },
#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
};
static struct i2c_board_info __initdata omap3h1_i2c2_board_info[] = {
#endif
    {
#ifdef CONFIG_MACH_OMAP3_H1_PV2
        I2C_BOARD_INFO("lsm6ds3", 0x6a),
#else
        I2C_BOARD_INFO("mpu6515", 0x68),
        .platform_data = &mpu_data,
#endif
    },
    { 
        /* Backlight */
        I2C_BOARD_INFO("lm3530-led", 0x38),
        .platform_data = &omap3h1_backlight_platform_data,
    },
    {
        I2C_BOARD_INFO("mXT224", 0x4a),
        .platform_data = &mxt_data,
    },
    {
        I2C_BOARD_INFO("cm3391", 0x10),
    },
#ifdef CONFIG_MACH_OMAP3_H1_EVT1
};
static struct i2c_board_info __initdata omap3h1_i2c3_board_info[] = {
#endif
    {
        I2C_BOARD_INFO("bq274xx", 0x55),
    },
};


/***************************************************************************
 * omap_uart data 
 */

/* Some notes:
		.dma_enabled	= false,
		.dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
		.dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
		.dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
		.autosuspend_timeout = DEFAULT_AUTOSUSPEND_DELAY, ( -1 or X ms. )
        
        .wakelock_timeout - for minnow, this is 150 (BT) or 50 (M4 debug).
              Can be left out.

        .DTR_* -> can be left out. I can't find anyone using it.

        int			    DTR_gpio;
        int			    DTR_inverted;
        int			    DTR_present;
        bool			wakeup_capable;
        
        bool			open_close_pm; - Minnow uses this for c55 only
        unsigned int	rx_trig;  Minnow, BT & debug only
*/

static struct omap_uart_port_info omap_uart_ports[] = {
    {
        .dma_enabled = false,	/* To specify DMA Mode */
        .dma_rx_buf_size  = DEFAULT_RXDMA_BUFSIZE,
        .dma_rx_timeout   = DEFAULT_RXDMA_TIMEOUT,
        .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
        .autosuspend_timeout = 1000,
        .wakelock_timeout = 150,
        .wake_peer = bcm_bt_lpm_exit_lpm_locked,
        .wakeup_capable = true,
    },
    {
        .dma_enabled = false,	/* To specify DMA Mode */
        .dma_rx_buf_size  = DEFAULT_RXDMA_BUFSIZE,
        .dma_rx_timeout   = DEFAULT_RXDMA_TIMEOUT,
        .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
        .autosuspend_timeout = 0,
        .wakeup_capable = false,
    },
    {
        .dma_enabled = false,	/* To specify DMA Mode */
        .dma_rx_buf_size  = DEFAULT_RXDMA_BUFSIZE,
        .dma_rx_timeout   = DEFAULT_RXDMA_TIMEOUT,
        .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
        .autosuspend_timeout = -1,
        .wakeup_capable = true,
    },
    {
        .dma_enabled = false,	/* To specify DMA Mode */
        .dma_rx_buf_size  = DEFAULT_RXDMA_BUFSIZE,
        .dma_rx_timeout   = DEFAULT_RXDMA_TIMEOUT,
        .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
        .autosuspend_timeout = 0,
        .wakeup_capable = false,
    },
};


/***************************************************************************
 * omap3_h1_i2c_init - init the i2c buses 
 *
 */

static int __init omap3_h1_i2c_init(void)
{
    int acc_irq;

    /* In Linux 3.10 we need to request an IRQ through 
     * gpio_to_irq. This means it can't be set at compile time, and
     * must be done at runtime. In other words, here.
     */
    
    gpio_request_one(ATMEL_MXT_GPIO, GPIOF_IN, "atmel_mxt_ts CHG");
	gpio_request_one(MPUIRQ_GPIO, GPIOF_IN, "Accl IRQ pin");

    acc_irq = gpio_to_irq(MPUIRQ_GPIO);

#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
	omap3h1_i2c2_board_info[2].irq = gpio_to_irq(ATMEL_MXT_GPIO);
    omap3h1_i2c2_board_info[0].irq = acc_irq;
#else
	omap3h1_i2c1_board_info[3].irq = gpio_to_irq(ATMEL_MXT_GPIO);
    omap3h1_i2c1_board_info[1].irq = acc_irq;
#endif

	gpio_request_one(USB_CS, GPIOF_OUT_INIT_HIGH, "USB on");
    
    /* Register buses */

	// omap_register_i2c_bus(1, 400, omap3h1_i2c1_board_info, ARRAY_SIZE(omap3h1_i2c1_board_info));
#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
	omap_register_i2c_bus(2, 400, omap3h1_i2c2_board_info, ARRAY_SIZE(omap3h1_i2c2_board_info));
#else
	omap_register_i2c_bus(2, 400, NULL, 0);
#endif
#ifdef CONFIG_MACH_OMAP3_H1_EVT1
	omap_register_i2c_bus(3, 400, omap3h1_i2c3_board_info, ARRAY_SIZE(omap3h1_i2c3_board_info));
#else
	omap_register_i2c_bus(3, 400, NULL, 0);
#endif
	return 0;
}


static struct platform_device *omap3h1_devices[] __initdata = {
        &bcm20702_bluetooth_device,
        &nop_phy_device,
		&omap3h1_dmic_codec,
};

static void __init omap3_h1_init(void)
{
    /* Read what we can from the device tree */

    of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);

	board_nand_init(omap3h1_nand_partitions,
                    ARRAY_SIZE(omap3h1_nand_partitions), NAND_CS,
                    NAND_BUSWIDTH_16, NULL);

	omap_sdrc_init(mt29c8g96_sdrc_params, mt29c8g96_sdrc_params);
	
    omap3_h1_i2c_init();

	platform_add_devices(omap3h1_devices, ARRAY_SIZE(omap3h1_devices));

	omap3h1_spi_init();

	omap_serial_board_init(omap_uart_ports);

    omap_display_init(&omap3h1_dss_data);

	usb_bind_phy("musb-hdrc.0.auto", 0, "nop_usb_xceiv"); /* "tusb-usb-h1" */

	usb_musb_init(&musb_board_data);
}

static const char *omap3_h1_boards_compat[] __initdata = {
	"olio,omap3-h1",
	NULL,
};

DT_MACHINE_START(OMAP3_H1, "Olio OMAP3 H1 (Flattened Device Tree)")
    .atag_offset = 0x100,
	.reserve	= omap_reserve,
	.map_io		= omap3_map_io,
	.init_early	= omap3630_init_early,
	/* .init_irq		= omap3_init_irq, */
    .init_irq	= omap_intc_of_init,
	.handle_irq	= omap3_intc_handle_irq,
	.init_machine	= omap3_h1_init,
	.init_late	= omap3630_init_late,
    .init_time  = omap3_sync32k_timer_init,
	/* .init_time	= omap3_secure_sync32k_timer_init, */
	.dt_compat	= omap3_h1_boards_compat,
	.restart	= omap3xxx_restart,
MACHINE_END

#if 0 /* removing ... for now */
MACHINE_START(OMAP3_H1, "Olio OMAP3 H1 Board")
	.atag_offset	= 0x100,
	.reserve		= omap_reserve,
	.map_io			= omap3_map_io,
	.init_early		= omap3630_init_early,
	.init_irq		= omap3_init_irq,
	.handle_irq		= omap3_intc_handle_irq,
	.init_machine	= omap3_h1_init,
	.init_late		= omap3630_init_late,
    .init_time      = omap3_sync32k_timer_init,
	/* .init_time		= omap3_secure_sync32k_timer_init, */
	/* .dt_compat		= omap3_h1_boards_compat, */
	.restart		= omap3xxx_restart,
MACHINE_END
#endif