summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/mtd/nand/omap2.c161
1 files changed, 62 insertions, 99 deletions
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 86ce48b2c47..b6a08b23853 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -139,6 +139,7 @@
#define BCH_ECC_SIZE0 0x0 /* ecc_size0 = 0, no oob protection */
#define BCH_ECC_SIZE1 0x20 /* ecc_size1 = 32 */
+#define BADBLOCK_MARKER_LENGTH 2
#define OMAP_ECC_BCH8_POLYNOMIAL 0x201b
#ifdef CONFIG_MTD_NAND_OMAP_BCH
@@ -149,17 +150,6 @@ static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10};
/* oob info generated runtime depending on ecc algorithm and layout selected */
static struct nand_ecclayout omap_oobinfo;
-/* Define some generic bad / good block scan pattern which are used
- * while scanning a device for factory marked good / bad blocks
- */
-static uint8_t scan_ff_pattern[] = { 0xff };
-static struct nand_bbt_descr bb_descrip_flashbased = {
- .options = NAND_BBT_SCANALLPAGES,
- .offs = 0,
- .len = 1,
- .pattern = scan_ff_pattern,
-};
-
struct omap_nand_info {
struct nand_hw_control controller;
@@ -184,7 +174,6 @@ struct omap_nand_info {
struct gpmc_nand_regs reg;
/* fields specific for BCHx_HW ECC scheme */
struct bch_control *bch;
- struct nand_ecclayout ecclayout;
bool is_elm_used;
struct device *elm_dev;
struct device_node *of_node;
@@ -1686,65 +1675,8 @@ static void omap3_free_bch(struct mtd_info *mtd)
}
}
-/**
- * omap3_init_bch_tail - Build an oob layout for BCH ECC correction.
- * @mtd: MTD device structure
- */
-static int omap3_init_bch_tail(struct mtd_info *mtd)
-{
- int i, steps, offset;
- struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
- mtd);
- struct nand_ecclayout *layout = &info->ecclayout;
-
- /* build oob layout */
- steps = mtd->writesize/info->nand.ecc.size;
- layout->eccbytes = steps*info->nand.ecc.bytes;
-
- /* do not bother creating special oob layouts for small page devices */
- if (mtd->oobsize < 64) {
- pr_err("BCH ecc is not supported on small page devices\n");
- goto fail;
- }
-
- /* reserve 2 bytes for bad block marker */
- if (layout->eccbytes+2 > mtd->oobsize) {
- pr_err("no oob layout available for oobsize %d eccbytes %u\n",
- mtd->oobsize, layout->eccbytes);
- goto fail;
- }
-
- /* ECC layout compatible with RBL for BCH8 */
- if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE))
- offset = 2;
- else
- offset = mtd->oobsize - layout->eccbytes;
-
- /* put ecc bytes at oob tail */
- for (i = 0; i < layout->eccbytes; i++)
- layout->eccpos[i] = offset + i;
-
- if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE))
- layout->oobfree[0].offset = 2 + layout->eccbytes * steps;
- else
- layout->oobfree[0].offset = 2;
-
- layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes;
- info->nand.ecc.layout = layout;
-
- if (!(info->nand.options & NAND_BUSWIDTH_16))
- info->nand.badblock_pattern = &bb_descrip_flashbased;
- return 0;
-fail:
- omap3_free_bch(mtd);
- return -1;
-}
-
#else
-static int omap3_init_bch_tail(struct mtd_info *mtd)
-{
- return -1;
-}
+
static void omap3_free_bch(struct mtd_info *mtd)
{
}
@@ -1756,8 +1688,9 @@ static int omap_nand_probe(struct platform_device *pdev)
struct omap_nand_platform_data *pdata;
struct mtd_info *mtd;
struct nand_chip *nand_chip;
+ struct nand_ecclayout *ecclayout;
int err;
- int i, offset;
+ int i;
dma_cap_mask_t mask;
unsigned sig;
struct resource *res;
@@ -1840,6 +1773,13 @@ static int omap_nand_probe(struct platform_device *pdev)
goto out_release_mem_region;
}
+ /* check for small page devices */
+ if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
+ pr_err("small page devices are not supported\n");
+ err = -EINVAL;
+ goto out_release_mem_region;
+ }
+
/* re-populate low-level callbacks based on xfer modes */
switch (pdata->xfer_type) {
case NAND_OMAP_PREFETCH_POLLED:
@@ -1931,6 +1871,8 @@ static int omap_nand_probe(struct platform_device *pdev)
}
/* populate MTD interface based on ECC scheme */
+ nand_chip->ecc.layout = &omap_oobinfo;
+ ecclayout = &omap_oobinfo;
switch (pdata->ecc_opt) {
case OMAP_ECC_HAM1_CODE_HW:
pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n");
@@ -1941,6 +1883,16 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->ecc.calculate = omap_calculate_ecc;
nand_chip->ecc.hwctl = omap_enable_hwecc;
nand_chip->ecc.correct = omap_correct_data;
+ /* define ECC layout */
+ ecclayout->eccbytes = nand_chip->ecc.bytes *
+ (mtd->writesize /
+ nand_chip->ecc.size);
+ if (nand_chip->options & NAND_BUSWIDTH_16)
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ else
+ ecclayout->eccpos[0] = 1;
+ ecclayout->oobfree->offset = ecclayout->eccpos[0] +
+ ecclayout->eccbytes;
break;
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
@@ -1953,6 +1905,13 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->ecc.hwctl = omap3_enable_hwecc_bch;
nand_chip->ecc.correct = omap3_correct_data_bch;
nand_chip->ecc.calculate = omap3_calculate_ecc_bch4;
+ /* define ECC layout */
+ ecclayout->eccbytes = nand_chip->ecc.bytes *
+ (mtd->writesize /
+ nand_chip->ecc.size);
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree->offset = ecclayout->eccpos[0] +
+ ecclayout->eccbytes;
/* software bch library is used for locating errors */
info->bch = init_bch(nand_chip->ecc.bytes,
nand_chip->ecc.strength,
@@ -1981,6 +1940,13 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->ecc.calculate = omap3_calculate_ecc_bch;
nand_chip->ecc.read_page = omap_read_page_bch;
nand_chip->ecc.write_page = omap_write_page_bch;
+ /* define ECC layout */
+ ecclayout->eccbytes = nand_chip->ecc.bytes *
+ (mtd->writesize /
+ nand_chip->ecc.size);
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree->offset = ecclayout->eccpos[0] +
+ ecclayout->eccbytes;
/* This ECC scheme requires ELM H/W block */
if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) {
pr_err("nand: error: could not initialize ELM\n");
@@ -2004,6 +1970,13 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->ecc.hwctl = omap3_enable_hwecc_bch;
nand_chip->ecc.correct = omap3_correct_data_bch;
nand_chip->ecc.calculate = omap3_calculate_ecc_bch8;
+ /* define ECC layout */
+ ecclayout->eccbytes = nand_chip->ecc.bytes *
+ (mtd->writesize /
+ nand_chip->ecc.size);
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree->offset = ecclayout->eccpos[0] +
+ ecclayout->eccbytes;
/* software bch library is used for locating errors */
info->bch = init_bch(nand_chip->ecc.bytes,
nand_chip->ecc.strength,
@@ -2038,6 +2011,13 @@ static int omap_nand_probe(struct platform_device *pdev)
pr_err("nand: error: could not initialize ELM\n");
goto out_release_mem_region;
}
+ /* define ECC layout */
+ ecclayout->eccbytes = nand_chip->ecc.bytes *
+ (mtd->writesize /
+ nand_chip->ecc.size);
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree->offset = ecclayout->eccpos[0] +
+ ecclayout->eccbytes;
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
@@ -2051,34 +2031,17 @@ static int omap_nand_probe(struct platform_device *pdev)
goto out_release_mem_region;
}
- /* rom code layout */
- if (pdata->ecc_opt == OMAP_ECC_HAM1_CODE_HW) {
-
- if (nand_chip->options & NAND_BUSWIDTH_16) {
- offset = 2;
- } else {
- offset = 1;
- nand_chip->badblock_pattern = &bb_descrip_flashbased;
- }
- omap_oobinfo.eccbytes = 3 * (mtd->writesize / 512);
- for (i = 0; i < omap_oobinfo.eccbytes; i++)
- omap_oobinfo.eccpos[i] = i+offset;
-
- omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes;
- omap_oobinfo.oobfree->length = mtd->oobsize -
- (offset + omap_oobinfo.eccbytes);
-
- nand_chip->ecc.layout = &omap_oobinfo;
- } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) ||
- (pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW) ||
- (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW_DETECTION_SW) ||
- (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) {
- /* build OOB layout for BCH ECC correction */
- err = omap3_init_bch_tail(mtd);
- if (err) {
- err = -EINVAL;
- goto out_release_mem_region;
- }
+ /* populate remaining ECC layout data */
+ ecclayout->oobfree->length = mtd->oobsize - (BADBLOCK_MARKER_LENGTH +
+ ecclayout->eccbytes);
+ for (i = 1; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = ecclayout->eccpos[0] + i;
+ /* check if NAND device's OOB is enough to store ECC signatures */
+ if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) {
+ pr_err("not enough OOB bytes required = %d, available=%d\n",
+ ecclayout->eccbytes, mtd->oobsize);
+ err = -EINVAL;
+ goto out_release_mem_region;
}
/* second phase scan */
generated by cgit v1.2.3-70-g09d2 (git 2.51.2) at 2025-11-04 05:11:23 +0000