diff options
Diffstat (limited to 'drivers/net/ethernet/i825xx/3c523.c')
| -rw-r--r-- | drivers/net/ethernet/i825xx/3c523.c | 1312 |
1 files changed, 0 insertions, 1312 deletions
diff --git a/drivers/net/ethernet/i825xx/3c523.c b/drivers/net/ethernet/i825xx/3c523.c deleted file mode 100644 index 8451ecd4c1e..00000000000 --- a/drivers/net/ethernet/i825xx/3c523.c +++ /dev/null @@ -1,1312 +0,0 @@ -/* - net-3-driver for the 3c523 Etherlink/MC card (i82586 Ethernet chip) - - - This is an extension to the Linux operating system, and is covered by the - same GNU General Public License that covers that work. - - Copyright 1995, 1996 by Chris Beauregard (cpbeaure@undergrad.math.uwaterloo.ca) - - This is basically Michael Hipp's ni52 driver, with a new probing - algorithm and some minor changes to the 82586 CA and reset routines. - Thanks a lot Michael for a really clean i82586 implementation! Unless - otherwise documented in ni52.c, any bugs are mine. - - Contrary to the Ethernet-HOWTO, this isn't based on the 3c507 driver in - any way. The ni52 is a lot easier to modify. - - sources: - ni52.c - - Crynwr packet driver collection was a great reference for my first - attempt at this sucker. The 3c507 driver also helped, until I noticed - that ni52.c was a lot nicer. - - EtherLink/MC: Micro Channel Ethernet Adapter Technical Reference - Manual, courtesy of 3Com CardFacts, documents the 3c523-specific - stuff. Information on CardFacts is found in the Ethernet HOWTO. - Also see <a href="http://www.3com.com/"> - - Microprocessor Communications Support Chips, T.J. Byers, ISBN - 0-444-01224-9, has a section on the i82586. It tells you just enough - to know that you really don't want to learn how to program the chip. - - The original device probe code was stolen from ps2esdi.c - - Known Problems: - Since most of the code was stolen from ni52.c, you'll run across the - same bugs in the 0.62 version of ni52.c, plus maybe a few because of - the 3c523 idiosynchacies. The 3c523 has 16K of RAM though, so there - shouldn't be the overrun problem that the 8K ni52 has. - - This driver is for a 16K adapter. It should work fine on the 64K - adapters, but it will only use one of the 4 banks of RAM. Modifying - this for the 64K version would require a lot of heinous bank - switching, which I'm sure not interested in doing. If you try to - implement a bank switching version, you'll basically have to remember - what bank is enabled and do a switch every time you access a memory - location that's not current. You'll also have to remap pointers on - the driver side, because it only knows about 16K of the memory. - Anyone desperate or masochistic enough to try? - - It seems to be stable now when multiple transmit buffers are used. I - can't see any performance difference, but then I'm working on a 386SX. - - Multicast doesn't work. It doesn't even pretend to work. Don't use - it. Don't compile your kernel with multicast support. I don't know - why. - - Features: - This driver is useable as a loadable module. If you try to specify an - IRQ or a IO address (via insmod 3c523.o irq=xx io=0xyyy), it will - search the MCA slots until it finds a 3c523 with the specified - parameters. - - This driver does support multiple ethernet cards when used as a module - (up to MAX_3C523_CARDS, the default being 4) - - This has been tested with both BNC and TP versions, internal and - external transceivers. Haven't tested with the 64K version (that I - know of). - - History: - Jan 1st, 1996 - first public release - Feb 4th, 1996 - update to 1.3.59, incorporated multicast diffs from ni52.c - Feb 15th, 1996 - added shared irq support - Apr 1999 - added support for multiple cards when used as a module - added option to disable multicast as is causes problems - Ganesh Sittampalam <ganesh.sittampalam@magdalen.oxford.ac.uk> - Stuart Adamson <stuart.adamson@compsoc.net> - Nov 2001 - added support for ethtool (jgarzik) - - $Header: /fsys2/home/chrisb/linux-1.3.59-MCA/drivers/net/RCS/3c523.c,v 1.1 1996/02/05 01:53:46 chrisb Exp chrisb $ - */ - -#define DRV_NAME "3c523" -#define DRV_VERSION "17-Nov-2001" - -#include <linux/init.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/ioport.h> -#include <linux/skbuff.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <linux/mca-legacy.h> -#include <linux/ethtool.h> -#include <linux/bitops.h> -#include <linux/jiffies.h> - -#include <asm/uaccess.h> -#include <asm/processor.h> -#include <asm/io.h> - -#include "3c523.h" - -/*************************************************************************/ -#define DEBUG /* debug on */ -#define SYSBUSVAL 0 /* 1 = 8 Bit, 0 = 16 bit - 3c523 only does 16 bit */ -#undef ELMC_MULTICAST /* Disable multicast support as it is somewhat seriously broken at the moment */ - -#define make32(ptr16) (p->memtop + (short) (ptr16) ) -#define make24(ptr32) ((char *) (ptr32) - p->base) -#define make16(ptr32) ((unsigned short) ((unsigned long) (ptr32) - (unsigned long) p->memtop )) - -/*************************************************************************/ -/* - Tables to which we can map values in the configuration registers. - */ -static int irq_table[] __initdata = { - 12, 7, 3, 9 -}; - -static int csr_table[] __initdata = { - 0x300, 0x1300, 0x2300, 0x3300 -}; - -static int shm_table[] __initdata = { - 0x0c0000, 0x0c8000, 0x0d0000, 0x0d8000 -}; - -/******************* how to calculate the buffers ***************************** - - - * IMPORTANT NOTE: if you configure only one NUM_XMIT_BUFFS, the driver works - * --------------- in a different (more stable?) mode. Only in this mode it's - * possible to configure the driver with 'NO_NOPCOMMANDS' - -sizeof(scp)=12; sizeof(scb)=16; sizeof(iscp)=8; -sizeof(scp)+sizeof(iscp)+sizeof(scb) = 36 = INIT -sizeof(rfd) = 24; sizeof(rbd) = 12; -sizeof(tbd) = 8; sizeof(transmit_cmd) = 16; -sizeof(nop_cmd) = 8; - - * if you don't know the driver, better do not change this values: */ - -#define RECV_BUFF_SIZE 1524 /* slightly oversized */ -#define XMIT_BUFF_SIZE 1524 /* slightly oversized */ -#define NUM_XMIT_BUFFS 1 /* config for both, 8K and 16K shmem */ -#define NUM_RECV_BUFFS_8 4 /* config for 8K shared mem */ -#define NUM_RECV_BUFFS_16 9 /* config for 16K shared mem */ - -#if (NUM_XMIT_BUFFS == 1) -#define NO_NOPCOMMANDS /* only possible with NUM_XMIT_BUFFS=1 */ -#endif - -/**************************************************************************/ - -#define DELAY(x) { mdelay(32 * x); } - -/* a much shorter delay: */ -#define DELAY_16(); { udelay(16) ; } - -/* wait for command with timeout: */ -#define WAIT_4_SCB_CMD() { int i; \ - for(i=0;i<1024;i++) { \ - if(!p->scb->cmd) break; \ - DELAY_16(); \ - if(i == 1023) { \ - pr_warning("%s:%d: scb_cmd timed out .. resetting i82586\n",\ - dev->name,__LINE__); \ - elmc_id_reset586(); } } } - -static irqreturn_t elmc_interrupt(int irq, void *dev_id); -static int elmc_open(struct net_device *dev); -static int elmc_close(struct net_device *dev); -static netdev_tx_t elmc_send_packet(struct sk_buff *, struct net_device *); -static struct net_device_stats *elmc_get_stats(struct net_device *dev); -static void elmc_timeout(struct net_device *dev); -#ifdef ELMC_MULTICAST -static void set_multicast_list(struct net_device *dev); -#endif -static const struct ethtool_ops netdev_ethtool_ops; - -/* helper-functions */ -static int init586(struct net_device *dev); -static int check586(struct net_device *dev, unsigned long where, unsigned size); -static void alloc586(struct net_device *dev); -static void startrecv586(struct net_device *dev); -static void *alloc_rfa(struct net_device *dev, void *ptr); -static void elmc_rcv_int(struct net_device *dev); -static void elmc_xmt_int(struct net_device *dev); -static void elmc_rnr_int(struct net_device *dev); - -struct priv { - unsigned long base; - char *memtop; - unsigned long mapped_start; /* Start of ioremap */ - volatile struct rfd_struct *rfd_last, *rfd_top, *rfd_first; - volatile struct scp_struct *scp; /* volatile is important */ - volatile struct iscp_struct *iscp; /* volatile is important */ - volatile struct scb_struct *scb; /* volatile is important */ - volatile struct tbd_struct *xmit_buffs[NUM_XMIT_BUFFS]; -#if (NUM_XMIT_BUFFS == 1) - volatile struct transmit_cmd_struct *xmit_cmds[2]; - volatile struct nop_cmd_struct *nop_cmds[2]; -#else - volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS]; - volatile struct nop_cmd_struct *nop_cmds[NUM_XMIT_BUFFS]; -#endif - volatile int nop_point, num_recv_buffs; - volatile char *xmit_cbuffs[NUM_XMIT_BUFFS]; - volatile int xmit_count, xmit_last; - volatile int slot; -}; - -#define elmc_attn586() {elmc_do_attn586(dev->base_addr,ELMC_CTRL_INTE);} -#define elmc_reset586() {elmc_do_reset586(dev->base_addr,ELMC_CTRL_INTE);} - -/* with interrupts disabled - this will clear the interrupt bit in the - 3c523 control register, and won't put it back. This effectively - disables interrupts on the card. */ -#define elmc_id_attn586() {elmc_do_attn586(dev->base_addr,0);} -#define elmc_id_reset586() {elmc_do_reset586(dev->base_addr,0);} - -/*************************************************************************/ -/* - Do a Channel Attention on the 3c523. This is extremely board dependent. - */ -static void elmc_do_attn586(int ioaddr, int ints) -{ - /* the 3c523 requires a minimum of 500 ns. The delays here might be - a little too large, and hence they may cut the performance of the - card slightly. If someone who knows a little more about Linux - timing would care to play with these, I'd appreciate it. */ - - /* this bit masking stuff is crap. I'd rather have separate - registers with strobe triggers for each of these functions. <sigh> - Ya take what ya got. */ - - outb(ELMC_CTRL_RST | 0x3 | ELMC_CTRL_CA | ints, ioaddr + ELMC_CTRL); - DELAY_16(); /* > 500 ns */ - outb(ELMC_CTRL_RST | 0x3 | ints, ioaddr + ELMC_CTRL); -} - -/*************************************************************************/ -/* - Reset the 82586 on the 3c523. Also very board dependent. - */ -static void elmc_do_reset586(int ioaddr, int ints) -{ - /* toggle the RST bit low then high */ - outb(0x3 | ELMC_CTRL_LBK, ioaddr + ELMC_CTRL); - DELAY_16(); /* > 500 ns */ - outb(ELMC_CTRL_RST | ELMC_CTRL_LBK | 0x3, ioaddr + ELMC_CTRL); - - elmc_do_attn586(ioaddr, ints); -} - -/********************************************** - * close device - */ - -static int elmc_close(struct net_device *dev) -{ - netif_stop_queue(dev); - elmc_id_reset586(); /* the hard way to stop the receiver */ - free_irq(dev->irq, dev); - return 0; -} - -/********************************************** - * open device - */ - -static int elmc_open(struct net_device *dev) -{ - int ret; - - elmc_id_attn586(); /* disable interrupts */ - - ret = request_irq(dev->irq, elmc_interrupt, IRQF_SHARED, - dev->name, dev); - if (ret) { - pr_err("%s: couldn't get irq %d\n", dev->name, dev->irq); - elmc_id_reset586(); - return ret; - } - alloc586(dev); - init586(dev); - startrecv586(dev); - netif_start_queue(dev); - return 0; /* most done by init */ -} - -/********************************************** - * Check to see if there's an 82586 out there. - */ - -static int __init check586(struct net_device *dev, unsigned long where, unsigned size) -{ - struct priv *p = netdev_priv(dev); - char *iscp_addrs[2]; - int i = 0; - - p->base = (unsigned long) isa_bus_to_virt((unsigned long)where) + size - 0x01000000; - p->memtop = isa_bus_to_virt((unsigned long)where) + size; - p->scp = (struct scp_struct *)(p->base + SCP_DEFAULT_ADDRESS); - memset((char *) p->scp, 0, sizeof(struct scp_struct)); - p->scp->sysbus = SYSBUSVAL; /* 1 = 8Bit-Bus, 0 = 16 Bit */ - - iscp_addrs[0] = isa_bus_to_virt((unsigned long)where); - iscp_addrs[1] = (char *) p->scp - sizeof(struct iscp_struct); - - for (i = 0; i < 2; i++) { - p->iscp = (struct iscp_struct *) iscp_addrs[i]; - memset((char *) p->iscp, 0, sizeof(struct iscp_struct)); - - p->scp->iscp = make24(p->iscp); - p->iscp->busy = 1; - - elmc_id_reset586(); - - /* reset586 does an implicit CA */ - - /* apparently, you sometimes have to kick the 82586 twice... */ - elmc_id_attn586(); - DELAY(1); - - if (p->iscp->busy) { /* i82586 clears 'busy' after successful init */ - return 0; - } - } - return 1; -} - -/****************************************************************** - * set iscp at the right place, called by elmc_probe and open586. - */ - -static void alloc586(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - elmc_id_reset586(); - DELAY(2); - - p->scp = (struct scp_struct *) (p->base + SCP_DEFAULT_ADDRESS); - p->scb = (struct scb_struct *) isa_bus_to_virt(dev->mem_start); - p->iscp = (struct iscp_struct *) ((char *) p->scp - sizeof(struct iscp_struct)); - - memset((char *) p->iscp, 0, sizeof(struct iscp_struct)); - memset((char *) p->scp, 0, sizeof(struct scp_struct)); - - p->scp->iscp = make24(p->iscp); - p->scp->sysbus = SYSBUSVAL; - p->iscp->scb_offset = make16(p->scb); - - p->iscp->busy = 1; - elmc_id_reset586(); - elmc_id_attn586(); - - DELAY(2); - - if (p->iscp->busy) - pr_err("%s: Init-Problems (alloc).\n", dev->name); - - memset((char *) p->scb, 0, sizeof(struct scb_struct)); -} - -/*****************************************************************/ - -static int elmc_getinfo(char *buf, int slot, void *d) -{ - int len = 0; - struct net_device *dev = d; - - if (dev == NULL) - return len; - - len += sprintf(buf + len, "Revision: 0x%x\n", - inb(dev->base_addr + ELMC_REVISION) & 0xf); - len += sprintf(buf + len, "IRQ: %d\n", dev->irq); - len += sprintf(buf + len, "IO Address: %#lx-%#lx\n", dev->base_addr, - dev->base_addr + ELMC_IO_EXTENT); - len += sprintf(buf + len, "Memory: %#lx-%#lx\n", dev->mem_start, - dev->mem_end - 1); - len += sprintf(buf + len, "Transceiver: %s\n", dev->if_port ? - "External" : "Internal"); - len += sprintf(buf + len, "Device: %s\n", dev->name); - len += sprintf(buf + len, "Hardware Address: %pM\n", - dev->dev_addr); - - return len; -} /* elmc_getinfo() */ - -static const struct net_device_ops netdev_ops = { - .ndo_open = elmc_open, - .ndo_stop = elmc_close, - .ndo_get_stats = elmc_get_stats, - .ndo_start_xmit = elmc_send_packet, - .ndo_tx_timeout = elmc_timeout, -#ifdef ELMC_MULTICAST - .ndo_set_rx_mode = set_multicast_list, -#endif - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -/*****************************************************************/ - -static int __init do_elmc_probe(struct net_device *dev) -{ - static int slot; - int base_addr = dev->base_addr; - int irq = dev->irq; - u_char status = 0; - u_char revision = 0; - int i = 0; - unsigned int size = 0; - int retval; - struct priv *pr = netdev_priv(dev); - - if (MCA_bus == 0) { - return -ENODEV; - } - /* search through the slots for the 3c523. */ - slot = mca_find_adapter(ELMC_MCA_ID, 0); - while (slot != -1) { - status = mca_read_stored_pos(slot, 2); - - dev->irq=irq_table[(status & ELMC_STATUS_IRQ_SELECT) >> 6]; - dev->base_addr=csr_table[(status & ELMC_STATUS_CSR_SELECT) >> 1]; - - /* - If we're trying to match a specified irq or IO address, - we'll reject a match unless it's what we're looking for. - Also reject it if the card is already in use. - */ - - if ((irq && irq != dev->irq) || - (base_addr && base_addr != dev->base_addr)) { - slot = mca_find_adapter(ELMC_MCA_ID, slot + 1); - continue; - } - if (!request_region(dev->base_addr, ELMC_IO_EXTENT, DRV_NAME)) { - slot = mca_find_adapter(ELMC_MCA_ID, slot + 1); - continue; - } - - /* found what we're looking for... */ - break; - } - - /* we didn't find any 3c523 in the slots we checked for */ - if (slot == MCA_NOTFOUND) - return (base_addr || irq) ? -ENXIO : -ENODEV; - - mca_set_adapter_name(slot, "3Com 3c523 Etherlink/MC"); - mca_set_adapter_procfn(slot, (MCA_ProcFn) elmc_getinfo, dev); - - /* if we get this far, adapter has been found - carry on */ - pr_info("%s: 3c523 adapter found in slot %d\n", dev->name, slot + 1); - - /* Now we extract configuration info from the card. - The 3c523 provides information in two of the POS registers, but - the second one is only needed if we want to tell the card what IRQ - to use. I suspect that whoever sets the thing up initially would - prefer we don't screw with those things. - - Note that we read the status info when we found the card... - - See 3c523.h for more details. - */ - - /* revision is stored in the first 4 bits of the revision register */ - revision = inb(dev->base_addr + ELMC_REVISION) & 0xf; - - /* according to docs, we read the interrupt and write it back to - the IRQ select register, since the POST might not configure the IRQ - properly. */ - switch (dev->irq) { - case 3: - mca_write_pos(slot, 3, 0x04); - break; - case 7: - mca_write_pos(slot, 3, 0x02); - break; - case 9: - mca_write_pos(slot, 3, 0x08); - break; - case 12: - mca_write_pos(slot, 3, 0x01); - break; - } - - pr->slot = slot; - - pr_info("%s: 3Com 3c523 Rev 0x%x at %#lx\n", dev->name, (int) revision, - dev->base_addr); - - /* Determine if we're using the on-board transceiver (i.e. coax) or - an external one. The information is pretty much useless, but I - guess it's worth brownie points. */ - dev->if_port = (status & ELMC_STATUS_DISABLE_THIN); - - /* The 3c523 has a 24K chunk of memory. The first 16K is the - shared memory, while the last 8K is for the EtherStart BIOS ROM. - Which we don't care much about here. We'll just tell Linux that - we're using 16K. MCA won't permit address space conflicts caused - by not mapping the other 8K. */ - dev->mem_start = shm_table[(status & ELMC_STATUS_MEMORY_SELECT) >> 3]; - - /* We're using MCA, so it's a given that the information about memory - size is correct. The Crynwr drivers do something like this. */ - - elmc_id_reset586(); /* seems like a good idea before checking it... */ - - size = 0x4000; /* check for 16K mem */ - if (!check586(dev, dev->mem_start, size)) { - pr_err("%s: memprobe, Can't find memory at 0x%lx!\n", dev->name, - dev->mem_start); - retval = -ENODEV; - goto err_out; - } - dev->mem_end = dev->mem_start + size; /* set mem_end showed by 'ifconfig' */ - - pr->memtop = isa_bus_to_virt(dev->mem_start) + size; - pr->base = (unsigned long) isa_bus_to_virt(dev->mem_start) + size - 0x01000000; - alloc586(dev); - - elmc_id_reset586(); /* make sure it doesn't generate spurious ints */ - - /* set number of receive-buffs according to memsize */ - pr->num_recv_buffs = NUM_RECV_BUFFS_16; - - /* dump all the assorted information */ - pr_info("%s: IRQ %d, %sternal xcvr, memory %#lx-%#lx.\n", dev->name, - dev->irq, dev->if_port ? "ex" : "in", - dev->mem_start, dev->mem_end - 1); - - /* The hardware address for the 3c523 is stored in the first six - bytes of the IO address. */ - for (i = 0; i < 6; i++) - dev->dev_addr[i] = inb(dev->base_addr + i); - - pr_info("%s: hardware address %pM\n", - dev->name, dev->dev_addr); - - dev->netdev_ops = &netdev_ops; - dev->watchdog_timeo = HZ; - dev->ethtool_ops = &netdev_ethtool_ops; - - /* note that we haven't actually requested the IRQ from the kernel. - That gets done in elmc_open(). I'm not sure that's such a good idea, - but it works, so I'll go with it. */ - -#ifndef ELMC_MULTICAST - dev->flags&=~IFF_MULTICAST; /* Multicast doesn't work */ -#endif - - retval = register_netdev(dev); - if (retval) - goto err_out; - - return 0; -err_out: - mca_set_adapter_procfn(slot, NULL, NULL); - release_region(dev->base_addr, ELMC_IO_EXTENT); - return retval; -} - -#ifdef MODULE -static void cleanup_card(struct net_device *dev) -{ - mca_set_adapter_procfn(((struct priv *)netdev_priv(dev))->slot, - NULL, NULL); - release_region(dev->base_addr, ELMC_IO_EXTENT); -} -#else -struct net_device * __init elmc_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct priv)); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = do_elmc_probe(dev); - if (err) - goto out; - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -/********************************************** - * init the chip (elmc-interrupt should be disabled?!) - * needs a correct 'allocated' memory - */ - -static int init586(struct net_device *dev) -{ - void *ptr; - unsigned long s; - int i, result = 0; - struct priv *p = netdev_priv(dev); - volatile struct configure_cmd_struct *cfg_cmd; - volatile struct iasetup_cmd_struct *ias_cmd; - volatile struct tdr_cmd_struct *tdr_cmd; - volatile struct mcsetup_cmd_struct *mc_cmd; - struct netdev_hw_addr *ha; - int num_addrs = netdev_mc_count(dev); - - ptr = (void *) ((char *) p->scb + sizeof(struct scb_struct)); - - cfg_cmd = (struct configure_cmd_struct *) ptr; /* configure-command */ - cfg_cmd->cmd_status = 0; - cfg_cmd->cmd_cmd = CMD_CONFIGURE | CMD_LAST; - cfg_cmd->cmd_link = 0xffff; - - cfg_cmd->byte_cnt = 0x0a; /* number of cfg bytes */ - cfg_cmd->fifo = 0x08; /* fifo-limit (8=tx:32/rx:64) */ - cfg_cmd->sav_bf = 0x40; /* hold or discard bad recv frames (bit 7) */ - cfg_cmd->adr_len = 0x2e; /* addr_len |!src_insert |pre-len |loopback */ - cfg_cmd->priority = 0x00; - cfg_cmd->ifs = 0x60; - cfg_cmd->time_low = 0x00; - cfg_cmd->time_high = 0xf2; - cfg_cmd->promisc = 0; - if (dev->flags & (IFF_ALLMULTI | IFF_PROMISC)) - cfg_cmd->promisc = 1; - cfg_cmd->carr_coll = 0x00; - - p->scb->cbl_offset = make16(cfg_cmd); - - p->scb->cmd = CUC_START; /* cmd.-unit start */ - elmc_id_attn586(); - - s = jiffies; /* warning: only active with interrupts on !! */ - while (!(cfg_cmd->cmd_status & STAT_COMPL)) { - if (time_after(jiffies, s + 30*HZ/100)) - break; - } - - if ((cfg_cmd->cmd_status & (STAT_OK | STAT_COMPL)) != (STAT_COMPL | STAT_OK)) { - pr_warning("%s (elmc): configure command failed: %x\n", dev->name, cfg_cmd->cmd_status); - return 1; - } - /* - * individual address setup - */ - ias_cmd = (struct iasetup_cmd_struct *) ptr; - - ias_cmd->cmd_status = 0; - ias_cmd->cmd_cmd = CMD_IASETUP | CMD_LAST; - ias_cmd->cmd_link = 0xffff; - - memcpy((char *) &ias_cmd->iaddr, (char *) dev->dev_addr, ETH_ALEN); - - p->scb->cbl_offset = make16(ias_cmd); - - p->scb->cmd = CUC_START; /* cmd.-unit start */ - elmc_id_attn586(); - - s = jiffies; - while (!(ias_cmd->cmd_status & STAT_COMPL)) { - if (time_after(jiffies, s + 30*HZ/100)) - break; - } - - if ((ias_cmd->cmd_status & (STAT_OK | STAT_COMPL)) != (STAT_OK | STAT_COMPL)) { - pr_warning("%s (elmc): individual address setup command failed: %04x\n", - dev->name, ias_cmd->cmd_status); - return 1; - } - /* - * TDR, wire check .. e.g. no resistor e.t.c - */ - tdr_cmd = (struct tdr_cmd_struct *) ptr; - - tdr_cmd->cmd_status = 0; - tdr_cmd->cmd_cmd = CMD_TDR | CMD_LAST; - tdr_cmd->cmd_link = 0xffff; - tdr_cmd->status = 0; - - p->scb->cbl_offset = make16(tdr_cmd); - - p->scb->cmd = CUC_START; /* cmd.-unit start */ - elmc_attn586(); - - s = jiffies; - while (!(tdr_cmd->cmd_status & STAT_COMPL)) { - if (time_after(jiffies, s + 30*HZ/100)) { - pr_warning("%s: %d Problems while running the TDR.\n", dev->name, __LINE__); - result = 1; - break; - } - } - - if (!result) { - DELAY(2); /* wait for result */ - result = tdr_cmd->status; - - p->scb->cmd = p->scb->status & STAT_MASK; - elmc_id_attn586(); /* ack the interrupts */ - - if (result & TDR_LNK_OK) { - /* empty */ - } else if (result & TDR_XCVR_PRB) { - pr_warning("%s: TDR: Transceiver problem!\n", dev->name); - } else if (result & TDR_ET_OPN) { - pr_warning("%s: TDR: No correct termination %d clocks away.\n", dev->name, result & TDR_TIMEMASK); - } else if (result & TDR_ET_SRT) { - if (result & TDR_TIMEMASK) /* time == 0 -> strange :-) */ - pr_warning("%s: TDR: Detected a short circuit %d clocks away.\n", dev->name, result & TDR_TIMEMASK); - } else { - pr_warning("%s: TDR: Unknown status %04x\n", dev->name, result); - } - } - /* - * ack interrupts - */ - p->scb->cmd = p->scb->status & STAT_MASK; - elmc_id_attn586(); - - /* - * alloc nop/xmit-cmds - */ -#if (NUM_XMIT_BUFFS == 1) - for (i = 0; i < 2; i++) { - p->nop_cmds[i] = (struct nop_cmd_struct *) ptr; - p->nop_cmds[i]->cmd_cmd = CMD_NOP; - p->nop_cmds[i]->cmd_status = 0; - p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i])); - ptr = (char *) ptr + sizeof(struct nop_cmd_struct); - } - p->xmit_cmds[0] = (struct transmit_cmd_struct *) ptr; /* transmit cmd/buff 0 */ - ptr = (char *) ptr + sizeof(struct transmit_cmd_struct); -#else - for (i = 0; i < NUM_XMIT_BUFFS; i++) { - p->nop_cmds[i] = (struct nop_cmd_struct *) ptr; - p->nop_cmds[i]->cmd_cmd = CMD_NOP; - p->nop_cmds[i]->cmd_status = 0; - p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i])); - ptr = (char *) ptr + sizeof(struct nop_cmd_struct); - p->xmit_cmds[i] = (struct transmit_cmd_struct *) ptr; /*transmit cmd/buff 0 */ - ptr = (char *) ptr + sizeof(struct transmit_cmd_struct); - } -#endif - - ptr = alloc_rfa(dev, (void *) ptr); /* init receive-frame-area */ - - /* - * Multicast setup - */ - - if (num_addrs) { - /* I don't understand this: do we really need memory after the init? */ - int len = ((char *) p->iscp - (char *) ptr - 8) / 6; - if (len <= 0) { - pr_err("%s: Ooooops, no memory for MC-Setup!\n", dev->name); - } else { - if (len < num_addrs) { - num_addrs = len; - pr_warning("%s: Sorry, can only apply %d MC-Address(es).\n", - dev->name, num_addrs); - } - mc_cmd = (struct mcsetup_cmd_struct *) ptr; - mc_cmd->cmd_status = 0; - mc_cmd->cmd_cmd = CMD_MCSETUP | CMD_LAST; - mc_cmd->cmd_link = 0xffff; - mc_cmd->mc_cnt = num_addrs * 6; - i = 0; - netdev_for_each_mc_addr(ha, dev) - memcpy((char *) mc_cmd->mc_list[i++], - ha->addr, 6); - p->scb->cbl_offset = make16(mc_cmd); - p->scb->cmd = CUC_START; - elmc_id_attn586(); - s = jiffies; - while (!(mc_cmd->cmd_status & STAT_COMPL)) { - if (time_after(jiffies, s + 30*HZ/100)) - break; - } - if (!(mc_cmd->cmd_status & STAT_COMPL)) { - pr_warning("%s: Can't apply multicast-address-list.\n", dev->name); - } - } - } - /* - * alloc xmit-buffs / init xmit_cmds - */ - for (i = 0; i < NUM_XMIT_BUFFS; i++) { - p->xmit_cbuffs[i] = (char *) ptr; /* char-buffs */ - ptr = (char *) ptr + XMIT_BUFF_SIZE; - p->xmit_buffs[i] = (struct tbd_struct *) ptr; /* TBD */ - ptr = (char *) ptr + sizeof(struct tbd_struct); - if ((void *) ptr > (void *) p->iscp) { - pr_err("%s: not enough shared-mem for your configuration!\n", dev->name); - return 1; - } - memset((char *) (p->xmit_cmds[i]), 0, sizeof(struct transmit_cmd_struct)); - memset((char *) (p->xmit_buffs[i]), 0, sizeof(struct tbd_struct)); - p->xmit_cmds[i]->cmd_status = STAT_COMPL; - p->xmit_cmds[i]->cmd_cmd = CMD_XMIT | CMD_INT; - p->xmit_cmds[i]->tbd_offset = make16((p->xmit_buffs[i])); - p->xmit_buffs[i]->next = 0xffff; - p->xmit_buffs[i]->buffer = make24((p->xmit_cbuffs[i])); - } - - p->xmit_count = 0; - p->xmit_last = 0; -#ifndef NO_NOPCOMMANDS - p->nop_point = 0; -#endif - - /* - * 'start transmitter' (nop-loop) - */ -#ifndef NO_NOPCOMMANDS - p->scb->cbl_offset = make16(p->nop_cmds[0]); - p->scb->cmd = CUC_START; - elmc_id_attn586(); - WAIT_4_SCB_CMD(); -#else - p->xmit_cmds[0]->cmd_link = 0xffff; - p->xmit_cmds[0]->cmd_cmd = CMD_XMIT | CMD_LAST | CMD_INT; -#endif - - return 0; -} - -/****************************************************** - * This is a helper routine for elmc_rnr_int() and init586(). - * It sets up the Receive Frame Area (RFA). - */ - -static void *alloc_rfa(struct net_device *dev, void *ptr) -{ - volatile struct rfd_struct *rfd = (struct rfd_struct *) ptr; - volatile struct rbd_struct *rbd; - int i; - struct priv *p = netdev_priv(dev); - - memset((char *) rfd, 0, sizeof(struct rfd_struct) * p->num_recv_buffs); - p->rfd_first = rfd; - - for (i = 0; i < p->num_recv_buffs; i++) { - rfd[i].next = make16(rfd + (i + 1) % p->num_recv_buffs); - } - rfd[p->num_recv_buffs - 1].last = RFD_SUSP; /* RU suspend */ - - ptr = (void *) (rfd + p->num_recv_buffs); - - rbd = (struct rbd_struct *) ptr; - ptr = (void *) (rbd + p->num_recv_buffs); - - /* clr descriptors */ - memset((char *) rbd, 0, sizeof(struct rbd_struct) * p->num_recv_buffs); - - for (i = 0; i < p->num_recv_buffs; i++) { - rbd[i].next = make16((rbd + (i + 1) % p->num_recv_buffs)); - rbd[i].size = RECV_BUFF_SIZE; - rbd[i].buffer = make24(ptr); - ptr = (char *) ptr + RECV_BUFF_SIZE; - } - - p->rfd_top = p->rfd_first; - p->rfd_last = p->rfd_first + p->num_recv_buffs - 1; - - p->scb->rfa_offset = make16(p->rfd_first); - p->rfd_first->rbd_offset = make16(rbd); - - return ptr; -} - - -/************************************************** - * Interrupt Handler ... - */ - -static irqreturn_t -elmc_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - unsigned short stat; - struct priv *p; - - if (!netif_running(dev)) { - /* The 3c523 has this habit of generating interrupts during the - reset. I'm not sure if the ni52 has this same problem, but it's - really annoying if we haven't finished initializing it. I was - hoping all the elmc_id_* commands would disable this, but I - might have missed a few. */ - - elmc_id_attn586(); /* ack inter. and disable any more */ - return IRQ_HANDLED; - } else if (!(ELMC_CTRL_INT & inb(dev->base_addr + ELMC_CTRL))) { - /* wasn't this device */ - return IRQ_NONE; - } - /* reading ELMC_CTRL also clears the INT bit. */ - - p = netdev_priv(dev); - - while ((stat = p->scb->status & STAT_MASK)) - { - p->scb->cmd = stat; - elmc_attn586(); /* ack inter. */ - - if (stat & STAT_CX) { - /* command with I-bit set complete */ - elmc_xmt_int(dev); - } - if (stat & STAT_FR) { - /* received a frame */ - elmc_rcv_int(dev); - } -#ifndef NO_NOPCOMMANDS - if (stat & STAT_CNA) { - /* CU went 'not ready' */ - if (netif_running(dev)) { - pr_warning("%s: oops! CU has left active state. stat: %04x/%04x.\n", - dev->name, (int) stat, (int) p->scb->status); - } - } -#endif - - if (stat & STAT_RNR) { - /* RU went 'not ready' */ - - if (p->scb->status & RU_SUSPEND) { - /* special case: RU_SUSPEND */ - - WAIT_4_SCB_CMD(); - p->scb->cmd = RUC_RESUME; - elmc_attn586(); - } else { - pr_warning("%s: Receiver-Unit went 'NOT READY': %04x/%04x.\n", - dev->name, (int) stat, (int) p->scb->status); - elmc_rnr_int(dev); - } - } - WAIT_4_SCB_CMD(); /* wait for ack. (elmc_xmt_int can be faster than ack!!) */ - if (p->scb->cmd) { /* timed out? */ - break; - } - } - return IRQ_HANDLED; -} - -/******************************************************* - * receive-interrupt - */ - -static void elmc_rcv_int(struct net_device *dev) -{ - int status; - unsigned short totlen; - struct sk_buff *skb; - struct rbd_struct *rbd; - struct priv *p = netdev_priv(dev); - - for (; (status = p->rfd_top->status) & STAT_COMPL;) { - rbd = (struct rbd_struct *) make32(p->rfd_top->rbd_offset); - - if (status & STAT_OK) { /* frame received without error? */ - if ((totlen = rbd->status) & RBD_LAST) { /* the first and the last buffer? */ - totlen &= RBD_MASK; /* length of this frame */ - rbd->status = 0; - skb = netdev_alloc_skb(dev, totlen + 2); - if (skb != NULL) { - skb_reserve(skb, 2); /* 16 byte alignment */ - skb_put(skb,totlen); - skb_copy_to_linear_data(skb, (char *) p->base+(unsigned long) rbd->buffer,totlen); - skb->protocol = eth_type_trans(skb, dev); - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += totlen; - } else { - dev->stats.rx_dropped++; - } - } else { - pr_warning("%s: received oversized frame.\n", dev->name); - dev->stats.rx_dropped++; - } - } else { /* frame !(ok), only with 'save-bad-frames' */ - pr_warning("%s: oops! rfd-error-status: %04x\n", dev->name, status); - dev->stats.rx_errors++; - } - p->rfd_top->status = 0; - p->rfd_top->last = RFD_SUSP; - p->rfd_last->last = 0; /* delete RU_SUSP */ - p->rfd_last = p->rfd_top; - p->rfd_top = (struct rfd_struct *) make32(p->rfd_top->next); /* step to next RFD */ - } -} - -/********************************************************** - * handle 'Receiver went not ready'. - */ - -static void elmc_rnr_int(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - dev->stats.rx_errors++; - - WAIT_4_SCB_CMD(); /* wait for the last cmd */ - p->scb->cmd = RUC_ABORT; /* usually the RU is in the 'no resource'-state .. abort it now. */ - elmc_attn586(); - WAIT_4_SCB_CMD(); /* wait for accept cmd. */ - - alloc_rfa(dev, (char *) p->rfd_first); - startrecv586(dev); /* restart RU */ - - pr_warning("%s: Receive-Unit restarted. Status: %04x\n", dev->name, p->scb->status); - -} - -/********************************************************** - * handle xmit - interrupt - */ - -static void elmc_xmt_int(struct net_device *dev) -{ - int status; - struct priv *p = netdev_priv(dev); - - status = p->xmit_cmds[p->xmit_last]->cmd_status; - if (!(status & STAT_COMPL)) { - pr_warning("%s: strange .. xmit-int without a 'COMPLETE'\n", dev->name); - } - if (status & STAT_OK) { - dev->stats.tx_packets++; - dev->stats.collisions += (status & TCMD_MAXCOLLMASK); - } else { - dev->stats.tx_errors++; - if (status & TCMD_LATECOLL) { - pr_warning("%s: late collision detected.\n", dev->name); - dev->stats.collisions++; - } else if (status & TCMD_NOCARRIER) { - dev->stats.tx_carrier_errors++; - pr_warning("%s: no carrier detected.\n", dev->name); - } else if (status & TCMD_LOSTCTS) { - pr_warning("%s: loss of CTS detected.\n", dev->name); - } else if (status & TCMD_UNDERRUN) { - dev->stats.tx_fifo_errors++; - pr_warning("%s: DMA underrun detected.\n", dev->name); - } else if (status & TCMD_MAXCOLL) { - pr_warning("%s: Max. collisions exceeded.\n", dev->name); - dev->stats.collisions += 16; - } - } - -#if (NUM_XMIT_BUFFS != 1) - if ((++p->xmit_last) == NUM_XMIT_BUFFS) { - p->xmit_last = 0; - } -#endif - - netif_wake_queue(dev); -} - -/*********************************************************** - * (re)start the receiver - */ - -static void startrecv586(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - p->scb->rfa_offset = make16(p->rfd_first); - p->scb->cmd = RUC_START; - elmc_attn586(); /* start cmd. */ - WAIT_4_SCB_CMD(); /* wait for accept cmd. (no timeout!!) */ -} - -/****************************************************** - * timeout - */ - -static void elmc_timeout(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - /* COMMAND-UNIT active? */ - if (p->scb->status & CU_ACTIVE) { - pr_debug("%s: strange ... timeout with CU active?!?\n", dev->name); - pr_debug("%s: X0: %04x N0: %04x N1: %04x %d\n", dev->name, - (int)p->xmit_cmds[0]->cmd_status, - (int)p->nop_cmds[0]->cmd_status, - (int)p->nop_cmds[1]->cmd_status, (int)p->nop_point); - p->scb->cmd = CUC_ABORT; - elmc_attn586(); - WAIT_4_SCB_CMD(); - p->scb->cbl_offset = make16(p->nop_cmds[p->nop_point]); - p->scb->cmd = CUC_START; - elmc_attn586(); - WAIT_4_SCB_CMD(); - netif_wake_queue(dev); - } else { - pr_debug("%s: xmitter timed out, try to restart! stat: %04x\n", - dev->name, p->scb->status); - pr_debug("%s: command-stats: %04x %04x\n", dev->name, - p->xmit_cmds[0]->cmd_status, p->xmit_cmds[1]->cmd_status); - elmc_close(dev); - elmc_open(dev); - } -} - -/****************************************************** - * send frame - */ - -static netdev_tx_t elmc_send_packet(struct sk_buff *skb, struct net_device *dev) -{ - int len; - int i; -#ifndef NO_NOPCOMMANDS - int next_nop; -#endif - struct priv *p = netdev_priv(dev); - - netif_stop_queue(dev); - - len = (ETH_ZLEN < skb->len) ? skb->len : ETH_ZLEN; - - if (len != skb->len) - memset((char *) p->xmit_cbuffs[p->xmit_count], 0, ETH_ZLEN); - skb_copy_from_linear_data(skb, (char *) p->xmit_cbuffs[p->xmit_count], skb->len); - -#if (NUM_XMIT_BUFFS == 1) -#ifdef NO_NOPCOMMANDS - p->xmit_buffs[0]->size = TBD_LAST | len; - for (i = 0; i < 16; i++) { - p->scb->cbl_offset = make16(p->xmit_cmds[0]); - p->scb->cmd = CUC_START; - p->xmit_cmds[0]->cmd_status = 0; - elmc_attn586(); - if (!i) { - dev_kfree_skb(skb); - } - WAIT_4_SCB_CMD(); - if ((p->scb->status & CU_ACTIVE)) { /* test it, because CU sometimes doesn't start immediately */ - break; - } - if (p->xmit_cmds[0]->cmd_status) { - break; - } - if (i == 15) { - pr_warning("%s: Can't start transmit-command.\n", dev->name); - } - } -#else - next_nop = (p->nop_point + 1) & 0x1; - p->xmit_buffs[0]->size = TBD_LAST | len; - - p->xmit_cmds[0]->cmd_link = p->nop_cmds[next_nop]->cmd_link - = make16((p->nop_cmds[next_nop])); - p->xmit_cmds[0]->cmd_status = p->nop_cmds[next_nop]->cmd_status = 0; - - p->nop_cmds[p->nop_point]->cmd_link = make16((p->xmit_cmds[0])); - p->nop_point = next_nop; - dev_kfree_skb(skb); -#endif -#else - p->xmit_buffs[p->xmit_count]->size = TBD_LAST | len; - if ((next_nop = p->xmit_count + 1) == NUM_XMIT_BUFFS) { - next_nop = 0; - } - p->xmit_cmds[p->xmit_count]->cmd_status = 0; - p->xmit_cmds[p->xmit_count]->cmd_link = p->nop_cmds[next_nop]->cmd_link - = make16((p->nop_cmds[next_nop])); - p->nop_cmds[next_nop]->cmd_status = 0; - p->nop_cmds[p->xmit_count]->cmd_link = make16((p->xmit_cmds[p->xmit_count])); - p->xmit_count = next_nop; - if (p->xmit_count != p->xmit_last) - netif_wake_queue(dev); - dev_kfree_skb(skb); -#endif - return NETDEV_TX_OK; -} - -/******************************************* - * Someone wanna have the statistics - */ - -static struct net_device_stats *elmc_get_stats(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - unsigned short crc, aln, rsc, ovrn; - - crc = p->scb->crc_errs; /* get error-statistic from the ni82586 */ - p->scb->crc_errs -= crc; - aln = p->scb->aln_errs; - p->scb->aln_errs -= aln; - rsc = p->scb->rsc_errs; - p->scb->rsc_errs -= rsc; - ovrn = p->scb->ovrn_errs; - p->scb->ovrn_errs -= ovrn; - - dev->stats.rx_crc_errors += crc; - dev->stats.rx_fifo_errors += ovrn; - dev->stats.rx_frame_errors += aln; - dev->stats.rx_dropped += rsc; - - return &dev->stats; -} - -/******************************************************** - * Set MC list .. - */ - -#ifdef ELMC_MULTICAST -static void set_multicast_list(struct net_device *dev) -{ - if (!dev->start) { - /* without a running interface, promiscuous doesn't work */ - return; - } - dev->start = 0; - alloc586(dev); - init586(dev); - startrecv586(dev); - dev->start = 1; -} -#endif - -static void netdev_get_drvinfo(struct net_device *dev, - struct ethtool_drvinfo *info) -{ - strcpy(info->driver, DRV_NAME); - strcpy(info->version, DRV_VERSION); - sprintf(info->bus_info, "MCA 0x%lx", dev->base_addr); -} - -static const struct ethtool_ops netdev_ethtool_ops = { - .get_drvinfo = netdev_get_drvinfo, -}; - -#ifdef MODULE - -/* Increase if needed ;) */ -#define MAX_3C523_CARDS 4 - -static struct net_device *dev_elmc[MAX_3C523_CARDS]; -static int irq[MAX_3C523_CARDS]; -static int io[MAX_3C523_CARDS]; -module_param_array(irq, int, NULL, 0); -module_param_array(io, int, NULL, 0); -MODULE_PARM_DESC(io, "EtherLink/MC I/O base address(es)"); -MODULE_PARM_DESC(irq, "EtherLink/MC IRQ number(s)"); -MODULE_LICENSE("GPL"); - -int __init init_module(void) -{ - int this_dev,found = 0; - - /* Loop until we either can't find any more cards, or we have MAX_3C523_CARDS */ - for(this_dev=0; this_dev<MAX_3C523_CARDS; this_dev++) { - struct net_device *dev = alloc_etherdev(sizeof(struct priv)); - if (!dev) - break; - dev->irq=irq[this_dev]; - dev->base_addr=io[this_dev]; - if (do_elmc_probe(dev) == 0) { - dev_elmc[this_dev] = dev; - found++; - continue; - } - free_netdev(dev); - if (io[this_dev]==0) - break; - pr_warning("3c523.c: No 3c523 card found at io=%#x\n",io[this_dev]); - } - - if(found==0) { - if (io[0]==0) - pr_notice("3c523.c: No 3c523 cards found\n"); - return -ENXIO; - } else return 0; -} - -void __exit cleanup_module(void) -{ - int this_dev; - for (this_dev=0; this_dev<MAX_3C523_CARDS; this_dev++) { - struct net_device *dev = dev_elmc[this_dev]; - if (dev) { - unregister_netdev(dev); - cleanup_card(dev); - free_netdev(dev); - } - } -} - -#endif /* MODULE */ |