summaryrefslogtreecommitdiff
path: root/arch
diff options
context:
space:
mode:
Diffstat (limited to 'arch')
-rw-r--r--arch/arm/boot/dts/omap3.dtsi9
-rw-r--r--arch/arm/boot/dts/omap3_h1.dts59
-rw-r--r--arch/arm/configs/omap3_h1_defconfig2
-rw-r--r--arch/arm/mach-omap2/Kconfig29
-rw-r--r--arch/arm/mach-omap2/board-omap3h1-bluetooth.c27
-rw-r--r--arch/arm/mach-omap2/board-omap3h1.c88
-rw-r--r--arch/arm/mach-omap2/serial.c1
7 files changed, 145 insertions, 70 deletions
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index f5ddf6aac1e..cae4e9725d0 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -13,12 +13,13 @@
/ {
compatible = "ti,omap3430", "ti,omap3";
interrupt-parent = <&intc>;
-
+/*
aliases {
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
};
+ */
cpus {
cpu@0 {
@@ -207,7 +208,7 @@
<&omap3_pmx_core 26 0xd9 1>,
<&omap3_pmx_core 28 0xc1 4>;
};
-
+/*
uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart1";
@@ -224,8 +225,8 @@
compatible = "ti,omap3-uart";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
- };
-
+ }; */
+
i2c1: i2c@48070000 {
compatible = "ti,omap3-i2c";
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/omap3_h1.dts b/arch/arm/boot/dts/omap3_h1.dts
index e570db34a7c..9111ebf872e 100644
--- a/arch/arm/boot/dts/omap3_h1.dts
+++ b/arch/arm/boot/dts/omap3_h1.dts
@@ -193,13 +193,21 @@
0x188 0x100 /* HSUSB0_DATA7, (OMAP_MUX_MODE0 | OMAP_PIN_INPUT) */
/* pin for controlling bluetooth chip, settings from uboot */
+ 0x1a8 0x004 /* CONTROL_PADCONF_MCSPI2_SIMO, (IDIS | PI | M4 ) */
0x1aa 0x004 /* CONTROL_PADCONF_MCSPI2_SOMI, (IDIS | PI | M4 ) */
/* BT_WAKE_GPIO - for waking up BT */
- /* OMAP_OFF_ENABLE and OMAP_OFF_PULL_EN for sleep modes. */
- 0x0da 0x1204 /* DSS_DATA23, (IDIS | PI | M4 ) */
+ /* OMAP_OFF_ENABLE, OMAP_OFF_PULL_EN, OMAP_OFF_OUTENABLE for sleep modes. */
+ 0x0da 0x1604 /* DSS_DATA23, (IDIS | PI | M4 ) */
+ /* UART3 pins */
+ 0x16e 0x4100 /* RX, input, off wake up */
+ 0x170 0x000 /* TX, output */
+
+ /* BT_HOST_WAKE */
+ /*0x9f4 0x4104 */ /* JTAG_EMU0 , (OMAP_MUX_MODE4 | OMAP_PIN_INPUT | OMAP_WAKEUPENABLE) */
/* Accelerometer interrupt */
+
/* I've tried configuring this both in the wkup pinmux (below) and here,
but this location makes it not function as an interrupt... ??? */
/* 0x9f6 0x4104 */ /* JTAG_EMU1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT |
@@ -213,29 +221,15 @@
0x18c 0x118 /* I2C1_SCA, MODE0 | INPUT_PULLUP */
>;
};
-
+
+ /*
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
- 0x18e 0x118 /* I2C2_SCL, MODE0 | INPUT_PULLUP */
- 0x190 0x118 /* I2C2_SDA, MODE0 | INPUT_PULLUP */
- >;
- };
-
- uart1_pins: pinmux_uart1_pins {
- pinctrl-single,pins = <
- /* uart1 */
- 0x152 0x118 /* UART1_RX, MODEO | (uboot: ien, pullup, m0 */
- 0x146 0x000 /* UART1_TX, MODE0 | OUTPUT, MODE0 */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- /* uart3 */
- 0x16e 0x4118 /* UART3_RX, MODEO | INPUT_PULLUP | OFFWAKEUP*/
- 0x170 0x000 /* UART3_TX, MODE0 | OUTPUT */
- >;
- };
+ 0x18e 0x118 */ /* I2C2_SCL, MODE0 | INPUT_PULLUP */
+ /* 0x190 0x118 */ /* I2C2_SDA, MODE0 | INPUT_PULLUP */
+ /* >; */
+ /* }; */
+
};
&omap3_pmx_wkup { /* pinmux@0x48002a00 */
@@ -248,11 +242,12 @@
0x018 0x000 /* SYS_OFF_MODE, MODE0 */
0x01a 0x10c /* SYS_CLKOUT1, MODE4 | INPUT_PULLDOWN */
/* Wakeup from Bluetooth */
- /* 0x024 0x4104 */ /* JTAG_EMU0, OMAP_MUX_MODE4 | OMAP_PIN_INPUT |
+ 0x024 0x4104 /* JTAG_EMU0, OMAP_MUX_MODE4 | OMAP_PIN_INPUT |
OMAP_PIN_OFF_WAKEUPENABLE */
/* Accelerometer interrupt */
0x026 0x410C /* JTAG_EMU1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT |
OMAP_PIN_OFF_WAKEUPENABLE */
+
>;
};
};
@@ -439,19 +434,3 @@
};
-
-&uart1 {
- pinctrl-0 = <&uart1_pins>;
- pinctrl-names = "default";
-};
-
-&uart2 {
- status = "disabled";
-};
-
-&uart3 {
- pinctrl-0 = <&uart3_pins>;
- pinctrl-names = "default";
- autosuspend-delay = <(-1)>; /* -1 = infinity. Negative value needs parens */
- wakeup-capable;
-};
diff --git a/arch/arm/configs/omap3_h1_defconfig b/arch/arm/configs/omap3_h1_defconfig
index 7ecf2b83edb..e50a5475d7b 100644
--- a/arch/arm/configs/omap3_h1_defconfig
+++ b/arch/arm/configs/omap3_h1_defconfig
@@ -935,7 +935,7 @@ CONFIG_FIB_RULES=y
# CONFIG_WIMAX is not set
CONFIG_RFKILL=y
# CONFIG_RFKILL_PM is not set
-CONFIG_RFKILL_INPUT=y
+# CONFIG_RFKILL_INPUT is not set
# CONFIG_RFKILL_REGULATOR is not set
CONFIG_RFKILL_GPIO=y
# CONFIG_RFKILL_WL18XX is not set
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index c3fdbc0f08a..2793feafaae 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -216,7 +216,7 @@ config MACH_OMAP3_H1
choice
prompt "Olio H1B build version"
- default MACH_OMAP3_H1_EVT2
+ default MACH_OMAP3_H1_PV2
config MACH_OMAP3_H1_EVT1
bool "EVT1 Build of the H1 board"
@@ -231,9 +231,32 @@ config MACH_OMAP3_H1_DVT1
depends on MACH_OMAP3_H1
config MACH_OMAP3_H1_DVT2
- bool "DVT2 Build of the H1 board"
- depends on MACH_OMAP3_H1
+ bool "DVT2 Build of the H1 board"
+ depends on MACH_OMAP3_H1
+
+config MACH_OMAP3_H1_PV
+ bool "PV Build of the H1 board"
+ depends on MACH_OMAP3_H1
+endchoice
+
+choice
+ prompt "Olio H1B PV build version"
+
+config MACH_OMAP3_H1_PV1
+ bool "PV Board with Invensense accelerometer."
+ depends on MACH_OMAP3_H1_PV
+ help
+ This is our first PV board, with Invensense accelerometer. Hopefully
+ it'll be extinct soon. Don't forget to add the invensense driver to
+ the kernel as well.
+config MACH_OMAP3_H1_PV2
+ bool "PV Board with ST accelerometer."
+ depends on MACH_OMAP3_H1_PV
+ help
+ This is the better PV board, with a more capable accelerometer from ST.
+ Might be our last board! Don't forget to configure the accelerometer in
+ the kernel as well.
endchoice
config MACH_DEVKIT8000
diff --git a/arch/arm/mach-omap2/board-omap3h1-bluetooth.c b/arch/arm/mach-omap2/board-omap3h1-bluetooth.c
index 323ec99ac6b..84108a79258 100644
--- a/arch/arm/mach-omap2/board-omap3h1-bluetooth.c
+++ b/arch/arm/mach-omap2/board-omap3h1-bluetooth.c
@@ -36,16 +36,19 @@
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <asm/mach-types.h>
+#include <linux/platform_data/serial-omap.h>
#include "serial.h"
#include "board-omap3h1.h"
#include <linux/regulator/driver.h>
static void update_host_wake_locked(int);
+#define BT_RESET_GPIO 179
#define BT_REG_GPIO 180
#define BT_RESET_GPIO 179
#define BT_WAKE_GPIO 93
#define BT_HOST_WAKE_GPIO 11
+#define UART_PORT 1
static struct rfkill *bt_rfkill;
static struct regulator *clk32ksys_reg;
@@ -76,13 +79,14 @@ static int bcm20702_bt_rfkill_set_power(void *data, bool blocked)
gpio_set_value(BT_RESET_GPIO, 1);
gpio_set_value(BT_REG_GPIO, 1);
+ gpio_set_value(BT_RESET_GPIO, 1);
} else {
// Chip won't toggle host_wake after reset. Make sure
// we don't hold the wake_lock until chip wakes up again.
update_host_wake_locked(0);
-
- gpio_set_value(BT_RESET_GPIO, 0);
+
+ gpio_set_value(BT_RESET_GPIO, 0);
gpio_set_value(BT_REG_GPIO, 0);
if (clk32ksys_reg && bt_enabled)
regulator_disable(clk32ksys_reg);
@@ -104,13 +108,13 @@ static void set_wake_locked(int wake)
if (!wake)
wake_unlock(&bt_lpm.wake_lock);
- //if (!wake_uart_enabled && wake)
- //omap_uart_enable(2);
+ if (!wake_uart_enabled && wake)
+ omap_serial_ext_uart_enable(UART_PORT);
gpio_set_value(BT_WAKE_GPIO, wake);
- //if (wake_uart_enabled && !wake)
- //omap_uart_disable(2);
+ if (wake_uart_enabled && !wake)
+ omap_serial_ext_uart_disable(UART_PORT);
wake_uart_enabled = wake;
}
@@ -146,11 +150,11 @@ static void update_host_wake_locked(int host_wake)
if (host_wake) {
wake_lock(&bt_lpm.wake_lock);
if (!host_wake_uart_enabled) {
- //omap_uart_enable(2);
+ omap_serial_ext_uart_enable(UART_PORT);
}
} else {
if (host_wake_uart_enabled) {
- //omap_uart_disable(2);
+ omap_serial_ext_uart_disable(UART_PORT);
}
// Take a timed wakelock, so that upper layers can take it.
// The chipset deasserts the hostwake lock, when there is no
@@ -259,15 +263,16 @@ static int bcm20702_bluetooth_probe(struct platform_device *pdev)
int rc = 0;
int ret = 0;
- rc = gpio_request(BT_RESET_GPIO, "bcm20702_nreset_gpip");
+ rc = gpio_request(BT_RESET_GPIO, "bcm20702_nreset_gpip");
+
if (unlikely(rc)) {
return rc;
}
rc = gpio_request(BT_REG_GPIO, "bcm20702_nshutdown_gpio");
if (unlikely(rc)) {
- gpio_free(BT_RESET_GPIO);
- return rc;
+ gpio_free(BT_RESET_GPIO);
+ return rc;
}
clk32ksys_reg = regulator_get(0, "clk32ksys");
diff --git a/arch/arm/mach-omap2/board-omap3h1.c b/arch/arm/mach-omap2/board-omap3h1.c
index 05dadc33c0f..0d3214c4150 100644
--- a/arch/arm/mach-omap2/board-omap3h1.c
+++ b/arch/arm/mach-omap2/board-omap3h1.c
@@ -82,7 +82,7 @@
#define DEFAULT_RXDMA_BUFSIZE 4096 /* RX DMA buffer size */
#define DEFAULT_RXDMA_TIMEOUT (3 * HZ)/* RX DMA timeout (jiffies) */
-#if defined(CONFIG_MACH_OMAP3_H1_DVT1) || defined(CONFIG_MACH_OMAP3_H1_DVT2)
+#if defined(CONFIG_MACH_OMAP3_H1_DVT1) || defined(CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
#define LCD_RESET_GPIO 94
#else
#define LCD_RESET_GPIO 122
@@ -185,6 +185,7 @@ static int __init omap3h1_spi_init(void) {
* (0 means VLogic, which I'm not sure what it is).
*/
+#ifndef CONFIG_MACH_OMAP3_H1_PV2
static struct mpu_platform_data mpu_data = {
.int_config = 0x00,
.level_shifter = 1,
@@ -192,6 +193,7 @@ static struct mpu_platform_data mpu_data = {
-1, 0, 0,
0, 0, 1 },
};
+#endif
static struct lm3530_platform_data omap3h1_backlight_platform_data = {
.mode = LM3530_BL_MODE_MANUAL,
@@ -267,16 +269,17 @@ static struct platform_device nop_phy_device = {
static struct i2c_board_info __initdata omap3h1_i2c1_board_info[] = {
{
},
-#ifdef CONFIG_MACH_OMAP3_H1_DVT2
+#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
};
static struct i2c_board_info __initdata omap3h1_i2c2_board_info[] = {
#endif
{
+#ifdef CONFIG_MACH_OMAP3_H1_PV2
+ I2C_BOARD_INFO("lsm6ds3", 0x6a),
+#else
I2C_BOARD_INFO("mpu6515", 0x68),
- // This is needed for the interrupt wake. IH_GPIO_BASE changed in 3.10
- // .irq = (IH_GPIO_BASE + MPUIRQ_GPIO),
- .irq = 0,
.platform_data = &mpu_data,
+#endif
},
{
/* Backlight */
@@ -299,6 +302,70 @@ static struct i2c_board_info __initdata omap3h1_i2c3_board_info[] = {
},
};
+
+/***************************************************************************
+ * omap_uart data
+ */
+
+/* Some notes:
+ .dma_enabled = false,
+ .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+ .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+ .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+ .autosuspend_timeout = DEFAULT_AUTOSUSPEND_DELAY, ( -1 or X ms. )
+
+ .wakelock_timeout - for minnow, this is 150 (BT) or 50 (M4 debug).
+ Can be left out.
+
+ .DTR_* -> can be left out. I can't find anyone using it.
+
+ int DTR_gpio;
+ int DTR_inverted;
+ int DTR_present;
+ bool wakeup_capable;
+
+ bool open_close_pm; - Minnow uses this for c55 only
+ unsigned int rx_trig; Minnow, BT & debug only
+*/
+
+static struct omap_uart_port_info omap_uart_ports[] = {
+ {
+ .dma_enabled = false, /* To specify DMA Mode */
+ .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+ .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+ .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+ .autosuspend_timeout = 1000,
+ .wakelock_timeout = 150,
+ .wake_peer = bcm_bt_lpm_exit_lpm_locked,
+ .wakeup_capable = true,
+ },
+ {
+ .dma_enabled = false, /* To specify DMA Mode */
+ .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+ .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+ .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+ .autosuspend_timeout = 0,
+ .wakeup_capable = false,
+ },
+ {
+ .dma_enabled = false, /* To specify DMA Mode */
+ .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+ .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+ .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+ .autosuspend_timeout = -1,
+ .wakeup_capable = true,
+ },
+ {
+ .dma_enabled = false, /* To specify DMA Mode */
+ .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+ .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+ .dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+ .autosuspend_timeout = 0,
+ .wakeup_capable = false,
+ },
+};
+
+
/***************************************************************************
* omap3_h1_i2c_init - init the i2c buses
*
@@ -314,16 +381,13 @@ static int __init omap3_h1_i2c_init(void)
*/
gpio_request_one(ATMEL_MXT_GPIO, GPIOF_IN, "atmel_mxt_ts CHG");
- gpio_request_one(MPUIRQ_GPIO, GPIOF_IN, "mpu6515 IRQ pin");
+ gpio_request_one(MPUIRQ_GPIO, GPIOF_IN, "Accl IRQ pin");
acc_irq = gpio_to_irq(MPUIRQ_GPIO);
-#ifdef CONFIG_MACH_OMAP3_H1_DVT2
+#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
omap3h1_i2c2_board_info[2].irq = gpio_to_irq(ATMEL_MXT_GPIO);
omap3h1_i2c2_board_info[0].irq = acc_irq;
-
- // ((struct tps65910_board *) (omap3h1_i2c1_board_info[0].platform_data))->irq =
- // gpio_to_irq (TPS_SYS_NIRQ);
#else
omap3h1_i2c1_board_info[3].irq = gpio_to_irq(ATMEL_MXT_GPIO);
omap3h1_i2c1_board_info[1].irq = acc_irq;
@@ -334,7 +398,7 @@ static int __init omap3_h1_i2c_init(void)
/* Register buses */
// omap_register_i2c_bus(1, 400, omap3h1_i2c1_board_info, ARRAY_SIZE(omap3h1_i2c1_board_info));
-#ifdef CONFIG_MACH_OMAP3_H1_DVT2
+#if defined (CONFIG_MACH_OMAP3_H1_DVT2) || defined (CONFIG_MACH_OMAP3_H1_PV)
omap_register_i2c_bus(2, 400, omap3h1_i2c2_board_info, ARRAY_SIZE(omap3h1_i2c2_board_info));
#else
omap_register_i2c_bus(2, 400, NULL, 0);
@@ -372,6 +436,8 @@ static void __init omap3_h1_init(void)
omap3h1_spi_init();
+ omap_serial_board_init(omap_uart_ports);
+
omap_display_init(&omap3h1_dss_data);
usb_bind_phy("musb-hdrc.0.auto", 0, "nop_usb_xceiv"); /* "tusb-usb-h1" */
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index b570d93cbb7..b1f3fb1d396 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -301,6 +301,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
omap_up.dma_rx_timeout = info->dma_rx_timeout;
omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
omap_up.autosuspend_timeout = info->autosuspend_timeout;
+ omap_up.wake_peer = info->wake_peer;
omap_up.DTR_gpio = info->DTR_gpio;
omap_up.DTR_inverted = info->DTR_inverted;
omap_up.DTR_present = info->DTR_present;
generated by cgit v1.2.3-70-g09d2 (git 2.51.2) at 2025-11-02 01:32:37 +0000