diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-omap3beagle.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3beagle.c | 128 |
1 files changed, 45 insertions, 83 deletions
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index bc30ab092d1..3ff3a2c4b86 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -80,6 +80,12 @@ static u8 omap3_beagle_get_rev(void) return omap3_beagle_version; } +static struct gpio omap3_beagle_rev_gpios[] __initdata = { + { 171, GPIOF_IN, "rev_id_0" }, + { 172, GPIOF_IN, "rev_id_1" }, + { 173, GPIOF_IN, "rev_id_2" }, +}; + static void __init omap3_beagle_init_rev(void) { int ret; @@ -89,21 +95,13 @@ static void __init omap3_beagle_init_rev(void) omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP); omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP); - ret = gpio_request(171, "rev_id_0"); - if (ret < 0) - goto fail0; - - ret = gpio_request(172, "rev_id_1"); - if (ret < 0) - goto fail1; - - ret = gpio_request(173, "rev_id_2"); - if (ret < 0) - goto fail2; - - gpio_direction_input(171); - gpio_direction_input(172); - gpio_direction_input(173); + ret = gpio_request_array(omap3_beagle_rev_gpios, + ARRAY_SIZE(omap3_beagle_rev_gpios)); + if (ret < 0) { + printk(KERN_ERR "Unable to get revision detection GPIO pins\n"); + omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN; + return; + } beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1) | (gpio_get_value(173) << 2); @@ -129,18 +127,6 @@ static void __init omap3_beagle_init_rev(void) printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev); omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN; } - - return; - -fail2: - gpio_free(172); -fail1: - gpio_free(171); -fail0: - printk(KERN_ERR "Unable to get revision detection GPIO pins\n"); - omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN; - - return; } static struct mtd_partition omap3beagle_nand_partitions[] = { @@ -235,13 +221,10 @@ static void __init beagle_display_init(void) { int r; - r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset"); - if (r < 0) { + r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW, + "DVI reset"); + if (r < 0) printk(KERN_ERR "Unable to get DVI reset GPIO\n"); - return; - } - - gpio_direction_output(beagle_dvi_device.reset_gpio, 0); } #include "sdram-micron-mt46h32m32lf-6.h" @@ -268,7 +251,7 @@ static struct gpio_led gpio_leds[]; static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { - int r; + int r, usb_pwr_level; if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { mmc[0].gpio_wp = -EINVAL; @@ -287,66 +270,46 @@ static int beagle_twl_gpio_setup(struct device *dev, beagle_vmmc1_supply.dev = mmc[0].dev; beagle_vsim_supply.dev = mmc[0].dev; - /* REVISIT: need ehci-omap hooks for external VBUS - * power switch and overcurrent detect - */ - if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) { - r = gpio_request(gpio + 1, "EHCI_nOC"); - if (!r) { - r = gpio_direction_input(gpio + 1); - if (r) - gpio_free(gpio + 1); - } - if (r) - pr_err("%s: unable to configure EHCI_nOC\n", __func__); - } - /* * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active * high / others active low) - */ - gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR"); - if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) - gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1); - else - gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0); - - /* DVI reset GPIO is different between beagle revisions */ - if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) - beagle_dvi_device.reset_gpio = 129; - else - beagle_dvi_device.reset_gpio = 170; - - /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ - gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; - - /* - * gpio + 1 on Xm controls the TFP410's enable line (active low) - * gpio + 2 control varies depending on the board rev as follows: - * P7/P8 revisions(prototype): Camera EN - * A2+ revisions (production): LDO (supplies DVI, serial, led blocks) + * DVI reset GPIO is different between beagle revisions */ if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { - r = gpio_request(gpio + 1, "nDVI_PWR_EN"); - if (!r) { - r = gpio_direction_output(gpio + 1, 0); - if (r) - gpio_free(gpio + 1); - } + usb_pwr_level = GPIOF_OUT_INIT_HIGH; + beagle_dvi_device.reset_gpio = 129; + /* + * gpio + 1 on Xm controls the TFP410's enable line (active low) + * gpio + 2 control varies depending on the board rev as below: + * P7/P8 revisions(prototype): Camera EN + * A2+ revisions (production): LDO (DVI, serial, led blocks) + */ + r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW, + "nDVI_PWR_EN"); if (r) pr_err("%s: unable to configure nDVI_PWR_EN\n", __func__); - r = gpio_request(gpio + 2, "DVI_LDO_EN"); - if (!r) { - r = gpio_direction_output(gpio + 2, 1); - if (r) - gpio_free(gpio + 2); - } + r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH, + "DVI_LDO_EN"); if (r) pr_err("%s: unable to configure DVI_LDO_EN\n", __func__); + } else { + usb_pwr_level = GPIOF_OUT_INIT_LOW; + beagle_dvi_device.reset_gpio = 170; + /* + * REVISIT: need ehci-omap hooks for external VBUS + * power switch and overcurrent detect + */ + if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC")) + pr_err("%s: unable to configure EHCI_nOC\n", __func__); } + gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR"); + + /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ + gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + return 0; } @@ -608,9 +571,8 @@ static void __init omap3_beagle_init(void) omap_serial_init(); omap_mux_init_gpio(170, OMAP_PIN_INPUT); - gpio_request(170, "DVI_nPD"); /* REVISIT leave DVI powered down until it's needed ... */ - gpio_direction_output(170, true); + gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD"); usb_musb_init(NULL); usbhs_init(&usbhs_bdata); |