1 files changed, 123 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c
new file mode 100644
index 00000000000..0b7d3277821
--- /dev/null
+++ b/arch/arm/mach-at91/board-dt.c
@@ -0,0 +1,123 @@
+/*
+ *  Setup code for AT91SAM Evaluation Kits with Device Tree support
+ *
+ *  Covers: * AT91SAM9G45-EKES  board
+ *          * AT91SAM9M10-EKES  board
+ *          * AT91SAM9M10G45-EK board
+ *
+ *  Copyright (C) 2011 Atmel,
+ *                2011 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/system_rev.h>
+#include <mach/at91sam9_smc.h>
+
+#include <asm/setup.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+	/* Initialize processor: 12.000 MHz crystal */
+	at91_initialize(12000000);
+
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+/* det_pin is not connected */
+static struct atmel_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+	.rdy_pin	= AT91_PIN_PC8,
+	.enable_pin	= AT91_PIN_PC14,
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	ek_nand_data.bus_width_16 = board_have_nand_16bit();
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+static const struct of_device_id aic_of_match[] __initconst = {
+	{ .compatible = "atmel,at91rm9200-aic", },
+	{},
+};
+
+static void __init at91_dt_init_irq(void)
+{
+	irq_domain_generate_simple(aic_of_match, 0xfffff000, 0);
+	at91_init_irq_default();
+}
+
+static void __init at91_dt_device_init(void)
+{
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+
+	/* NAND */
+	ek_add_device_nand();
+}
+
+static const char *at91_dt_board_compat[] __initdata = {
+	"atmel,at91sam9m10g45ek",
+	"calao,usb-a9g20",
+	NULL
+};
+
+DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)")
+	/* Maintainer: Atmel */
+	.timer		= &at91sam926x_timer,
+	.map_io		= at91_map_io,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_dt_init_irq,
+	.init_machine	= at91_dt_device_init,
+	.dt_compat	= at91_dt_board_compat,
+MACHINE_END