diff options
| -rw-r--r-- | drivers/tty/serial/Kconfig | 13 | ||||
| -rw-r--r-- | drivers/tty/serial/Makefile | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/max3107.c | 1215 | ||||
| -rw-r--r-- | drivers/tty/serial/max3107.h | 441 | ||||
| -rw-r--r-- | drivers/tty/serial/max310x.c | 1259 | ||||
| -rw-r--r-- | include/linux/platform_data/max310x.h | 67 | ||||
| -rw-r--r-- | include/linux/serial_core.h | 4 |
7 files changed, 1339 insertions, 1662 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 00207865ec5..7b3d9de938e 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -257,12 +257,19 @@ config SERIAL_MAX3100 help MAX3100 chip support -config SERIAL_MAX3107 - tristate "MAX3107 support" +config SERIAL_MAX310X + bool "MAX310X support" depends on SPI select SERIAL_CORE + select REGMAP_SPI if SPI + default n help - MAX3107 chip support + This selects support for an advanced UART from Maxim (Dallas). + Supported ICs are MAX3107, MAX3108. + Each IC contains 128 words each of receive and transmit FIFO + that can be controlled through I2C or high-speed SPI. + + Say Y here if you want to support this ICs. config SERIAL_DZ bool "DECstation DZ serial driver" diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index 8a5df3804e5..2af9e5279da 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -28,7 +28,7 @@ obj-$(CONFIG_SERIAL_BFIN) += bfin_uart.o obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o obj-$(CONFIG_SERIAL_MAX3100) += max3100.o -obj-$(CONFIG_SERIAL_MAX3107) += max3107.o +obj-$(CONFIG_SERIAL_MAX310X) += max310x.o obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o obj-$(CONFIG_SERIAL_MUX) += mux.o obj-$(CONFIG_SERIAL_68328) += 68328serial.o diff --git a/drivers/tty/serial/max3107.c b/drivers/tty/serial/max3107.c deleted file mode 100644 index 17c7ba805d9..00000000000 --- a/drivers/tty/serial/max3107.c +++ /dev/null @@ -1,1215 +0,0 @@ -/* - * max3107.c - spi uart protocol driver for Maxim 3107 - * Based on max3100.c - * by Christian Pellegrin <chripell@evolware.org> - * and max3110.c - * by Feng Tang <feng.tang@intel.com> - * - * Copyright (C) Aavamobile 2009 - * - * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - * - */ - -#include <linux/delay.h> -#include <linux/device.h> -#include <linux/serial_core.h> -#include <linux/serial.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/gpio.h> -#include <linux/spi/spi.h> -#include <linux/freezer.h> -#include <linux/module.h> -#include "max3107.h" - -static const struct baud_table brg26_ext[] = { - { 300, MAX3107_BRG26_B300 }, - { 600, MAX3107_BRG26_B600 }, - { 1200, MAX3107_BRG26_B1200 }, - { 2400, MAX3107_BRG26_B2400 }, - { 4800, MAX3107_BRG26_B4800 }, - { 9600, MAX3107_BRG26_B9600 }, - { 19200, MAX3107_BRG26_B19200 }, - { 57600, MAX3107_BRG26_B57600 }, - { 115200, MAX3107_BRG26_B115200 }, - { 230400, MAX3107_BRG26_B230400 }, - { 460800, MAX3107_BRG26_B460800 }, - { 921600, MAX3107_BRG26_B921600 }, - { 0, 0 } -}; - -static const struct baud_table brg13_int[] = { - { 300, MAX3107_BRG13_IB300 }, - { 600, MAX3107_BRG13_IB600 }, - { 1200, MAX3107_BRG13_IB1200 }, - { 2400, MAX3107_BRG13_IB2400 }, - { 4800, MAX3107_BRG13_IB4800 }, - { 9600, MAX3107_BRG13_IB9600 }, - { 19200, MAX3107_BRG13_IB19200 }, - { 57600, MAX3107_BRG13_IB57600 }, - { 115200, MAX3107_BRG13_IB115200 }, - { 230400, MAX3107_BRG13_IB230400 }, - { 460800, MAX3107_BRG13_IB460800 }, - { 921600, MAX3107_BRG13_IB921600 }, - { 0, 0 } -}; - -static u32 get_new_brg(int baud, struct max3107_port *s) -{ - int i; - const struct baud_table *baud_tbl = s->baud_tbl; - - for (i = 0; i < 13; i++) { - if (baud == baud_tbl[i].baud) - return baud_tbl[i].new_brg; - } - - return 0; -} - -/* Perform SPI transfer for write/read of device register(s) */ -int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len) -{ - struct spi_message spi_msg; - struct spi_transfer spi_xfer; - - /* Initialize SPI ,message */ - spi_message_init(&spi_msg); - - /* Initialize SPI transfer */ - memset(&spi_xfer, 0, sizeof spi_xfer); - spi_xfer.len = len; - spi_xfer.tx_buf = tx; - spi_xfer.rx_buf = rx; - spi_xfer.speed_hz = MAX3107_SPI_SPEED; - - /* Add SPI transfer to SPI message */ - spi_message_add_tail(&spi_xfer, &spi_msg); - -#ifdef DBG_TRACE_SPI_DATA - { - int i; - pr_info("tx len %d:\n", spi_xfer.len); - for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) - pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]); - pr_info("\n"); - } -#endif - - /* Perform synchronous SPI transfer */ - if (spi_sync(s->spi, &spi_msg)) { - dev_err(&s->spi->dev, "spi_sync failure\n"); - return -EIO; - } - -#ifdef DBG_TRACE_SPI_DATA - if (spi_xfer.rx_buf) { - int i; - pr_info("rx len %d:\n", spi_xfer.len); - for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) - pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]); - pr_info("\n"); - } -#endif - return 0; -} -EXPORT_SYMBOL_GPL(max3107_rw); - -/* Puts received data to circular buffer */ -static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data, - int len) -{ - struct uart_port *port = &s->port; - struct tty_struct *tty; - - if (!port->state) - return; - - tty = port->state->port.tty; - if (!tty) - return; - - /* Insert received data */ - tty_insert_flip_string(tty, data, len); - /* Update RX counter */ - port->icount.rx += len; -} - -/* Handle data receiving */ -static void max3107_handlerx(struct max3107_port *s, u16 rxlvl) -{ - int i; - int j; - int len; /* SPI transfer buffer length */ - u16 *buf; - u8 *valid_str; - - if (!s->rx_enabled) - /* RX is disabled */ - return; - - if (rxlvl == 0) { - /* RX fifo is empty */ - return; - } else if (rxlvl >= MAX3107_RX_FIFO_SIZE) { - dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl); - /* Ensure sanity of RX level */ - rxlvl = MAX3107_RX_FIFO_SIZE; - } - if ((s->rxbuf == 0) || (s->rxstr == 0)) { - dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n"); - return; - } - buf = s->rxbuf; - valid_str = s->rxstr; - while (rxlvl) { - pr_debug("rxlvl %d\n", rxlvl); - /* Clear buffer */ - memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2)); - len = 0; - if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) { - /* First disable RX FIFO interrupt */ - pr_debug("Disabling RX INT\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT; - buf[0] |= s->irqen_reg; - len++; - } - /* Just increase the length by amount of words in FIFO since - * buffer was zeroed and SPI transfer of 0x0000 means reading - * from RX FIFO - */ - len += rxlvl; - /* Append RX level query */ - buf[len] = MAX3107_RXFIFOLVL_REG; - len++; - - /* Perform the SPI transfer */ - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) { - dev_err(&s->spi->dev, "SPI transfer for RX h failed\n"); - return; - } - - /* Skip RX FIFO interrupt disabling word if it was added */ - j = ((len - 1) - rxlvl); - /* Read received words */ - for (i = 0; i < rxlvl; i++, j++) - valid_str[i] = (u8)buf[j]; - put_data_to_circ_buf(s, valid_str, rxlvl); - /* Get new RX level */ - rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK); - } - - if (s->rx_enabled) { - /* RX still enabled, re-enable RX FIFO interrupt */ - pr_debug("Enabling RX INT\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; - buf[0] |= s->irqen_reg; - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n"); - } - - /* Push the received data to receivers */ - if (s->port.state->port.tty) - tty_flip_buffer_push(s->port.state->port.tty); -} - - -/* Handle data sending */ -static void max3107_handletx(struct max3107_port *s) -{ - struct circ_buf *xmit = &s->port.state->xmit; - int i; - unsigned long flags; - int len; /* SPI transfer buffer length */ - u16 *buf; - - if (!s->tx_fifo_empty) - /* Don't send more data before previous data is sent */ - return; - - if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port)) - /* No data to send or TX is stopped */ - return; - - if (!s->txbuf) { - dev_warn(&s->spi->dev, "Txbuf isn't ready\n"); - return; - } - buf = s->txbuf; - /* Get length of data pending in circular buffer */ - len = uart_circ_chars_pending(xmit); - if (len) { - /* Limit to size of TX FIFO */ - if (len > MAX3107_TX_FIFO_SIZE) - len = MAX3107_TX_FIFO_SIZE; - - pr_debug("txlen %d\n", len); - - /* Update TX counter */ - s->port.icount.tx += len; - - /* TX FIFO will no longer be empty */ - s->tx_fifo_empty = 0; - - i = 0; - if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) { - /* First disable TX empty interrupt */ - pr_debug("Disabling TE INT\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT; - buf[i] |= s->irqen_reg; - i++; - len++; - } - /* Add data to send */ - spin_lock_irqsave(&s->port.lock, flags); - for ( ; i < len ; i++) { - buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG); - buf[i] |= ((u16)xmit->buf[xmit->tail] & - MAX3107_SPI_TX_DATA_MASK); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - } - spin_unlock_irqrestore(&s->port.lock, flags); - if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) { - /* Enable TX empty interrupt */ - pr_debug("Enabling TE INT\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT; - buf[i] |= s->irqen_reg; - i++; - len++; - } - if (!s->tx_enabled) { - /* Enable TX */ - pr_debug("Enable TX\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT; - buf[i] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - s->tx_enabled = 1; - i++; - len++; - } - - /* Perform the SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, len*2)) { - dev_err(&s->spi->dev, - "SPI transfer TX handling failed\n"); - return; - } - } - - /* Indicate wake up if circular buffer is getting low on data */ - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&s->port); - -} - -/* Handle interrupts - * Also reads and returns current RX FIFO level - */ -static u16 handle_interrupt(struct max3107_port *s) -{ - u16 buf[4]; /* Buffer for SPI transfers */ - u8 irq_status; - u16 rx_level; - unsigned long flags; - - /* Read IRQ status register */ - buf[0] = MAX3107_IRQSTS_REG; - /* Read status IRQ status register */ - buf[1] = MAX3107_STS_IRQSTS_REG; - /* Read LSR IRQ status register */ - buf[2] = MAX3107_LSR_IRQSTS_REG; - /* Query RX level */ - buf[3] = MAX3107_RXFIFOLVL_REG; - - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) { - dev_err(&s->spi->dev, - "SPI transfer for INTR handling failed\n"); - return 0; - } - - irq_status = (u8)buf[0]; - pr_debug("IRQSTS %x\n", irq_status); - rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK); - - if (irq_status & MAX3107_IRQ_LSR_BIT) { - /* LSR interrupt */ - if (buf[2] & MAX3107_LSR_RXTO_BIT) - /* RX timeout interrupt, - * handled by normal RX handling - */ - pr_debug("RX TO INT\n"); - } - - if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) { - /* Tx empty interrupt, - * disable TX and set tx_fifo_empty flag - */ - pr_debug("TE INT, disabling TX\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; - buf[0] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "SPI transfer TX dis failed\n"); - s->tx_enabled = 0; - s->tx_fifo_empty = 1; - } - - if (irq_status & MAX3107_IRQ_RXFIFO_BIT) - /* RX FIFO interrupt, - * handled by normal RX handling - */ - pr_debug("RFIFO INT\n"); - - /* Return RX level */ - return rx_level; -} - -/* Trigger work thread*/ -static void max3107_dowork(struct max3107_port *s) -{ - if (!work_pending(&s->work) && !freezing(current) && !s->suspended) - queue_work(s->workqueue, &s->work); - else - dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n"); -} - -/* Work thread */ -static void max3107_work(struct work_struct *w) -{ - struct max3107_port *s = container_of(w, struct max3107_port, work); - u16 rxlvl = 0; - int len; /* SPI transfer buffer length */ - u16 buf[5]; /* Buffer for SPI transfers */ - unsigned long flags; - - /* Start by reading current RX FIFO level */ - buf[0] = MAX3107_RXFIFOLVL_REG; - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { - dev_err(&s->spi->dev, "SPI transfer RX lev failed\n"); - rxlvl = 0; - } else { - rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK); - } - - do { - pr_debug("rxlvl %d\n", rxlvl); - - /* Handle RX */ - max3107_handlerx(s, rxlvl); - rxlvl = 0; - - if (s->handle_irq) { - /* Handle pending interrupts - * We also get new RX FIFO level since new data may - * have been received while pushing received data to - * receivers - */ - s->handle_irq = 0; - rxlvl = handle_interrupt(s); - } - - /* Handle TX */ - max3107_handletx(s); - - /* Handle configuration changes */ - len = 0; - spin_lock_irqsave(&s->data_lock, flags); - if (s->mode1_commit) { - pr_debug("mode1_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - buf[len++] |= s->mode1_reg; - s->mode1_commit = 0; - } - if (s->lcr_commit) { - pr_debug("lcr_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG); - buf[len++] |= s->lcr_reg; - s->lcr_commit = 0; - } - if (s->brg_commit) { - pr_debug("brg_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG); - buf[len++] |= ((s->brg_cfg >> 16) & - MAX3107_SPI_TX_DATA_MASK); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG); - buf[len++] |= ((s->brg_cfg >> 8) & - MAX3107_SPI_TX_DATA_MASK); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG); - buf[len++] |= ((s->brg_cfg) & 0xff); - s->brg_commit = 0; - } - spin_unlock_irqrestore(&s->data_lock, flags); - - if (len > 0) { - if (max3107_rw(s, (u8 *)buf, NULL, len * 2)) - dev_err(&s->spi->dev, - "SPI transfer config failed\n"); - } - - /* Reloop if interrupt handling indicated data in RX FIFO */ - } while (rxlvl); - -} - -/* Set sleep mode */ -static void max3107_set_sleep(struct max3107_port *s, int mode) -{ - u16 buf[1]; /* Buffer for SPI transfer */ - unsigned long flags; - pr_debug("enter, mode %d\n", mode); - - buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - switch (mode) { - case MAX3107_DISABLE_FORCED_SLEEP: - s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT; - break; - case MAX3107_ENABLE_FORCED_SLEEP: - s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT; - break; - case MAX3107_DISABLE_AUTOSLEEP: - s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT; - break; - case MAX3107_ENABLE_AUTOSLEEP: - s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT; - break; - default: - spin_unlock_irqrestore(&s->data_lock, flags); - dev_warn(&s->spi->dev, "invalid sleep mode\n"); - return; - } - buf[0] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n"); - - if (mode == MAX3107_DISABLE_AUTOSLEEP || - mode == MAX3107_DISABLE_FORCED_SLEEP) - msleep(MAX3107_WAKEUP_DELAY); -} - -/* Perform full register initialization */ -static void max3107_register_init(struct max3107_port *s) -{ - u16 buf[11]; /* Buffer for SPI transfers */ - - /* 1. Configure baud rate, 9600 as default */ - s->baud = 9600; - /* the below is default*/ - if (s->ext_clk) { - s->brg_cfg = MAX3107_BRG26_B9600; - s->baud_tbl = (struct baud_table *)brg26_ext; - } else { - s->brg_cfg = MAX3107_BRG13_IB9600; - s->baud_tbl = (struct baud_table *)brg13_int; - } - - if (s->pdata->init) - s->pdata->init(s); - - buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG) - | ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK); - buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG) - | ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK); - buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG) - | ((s->brg_cfg) & 0xff); - - /* 2. Configure LCR register, 8N1 mode by default */ - s->lcr_reg = MAX3107_LCR_WORD_LEN_8; - buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG) - | s->lcr_reg; - - /* 3. Configure MODE 1 register */ - s->mode1_reg = 0; - /* Enable IRQ pin */ - s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT; - /* Disable TX */ - s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; - s->tx_enabled = 0; - /* RX is enabled */ - s->rx_enabled = 1; - buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG) - | s->mode1_reg; - - /* 4. Configure MODE 2 register */ - buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); - if (s->loopback) { - /* Enable loopback */ - buf[5] |= MAX3107_MODE2_LOOPBACK_BIT; - } - /* Reset FIFOs */ - buf[5] |= MAX3107_MODE2_FIFORST_BIT; - s->tx_fifo_empty = 1; - - /* 5. Configure FIFO trigger level register */ - buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG); - /* RX FIFO trigger for 16 words, TX FIFO trigger not used */ - buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0)); - - /* 6. Configure flow control levels */ - buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG); - /* Flow control halt level 96, resume level 48 */ - buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96)); - - /* 7. Configure flow control */ - buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG); - /* Enable auto CTS and auto RTS flow control */ - buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT); - - /* 8. Configure RX timeout register */ - buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG); - /* Timeout after 48 character intervals */ - buf[9] |= 0x0030; - - /* 9. Configure LSR interrupt enable register */ - buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG); - /* Enable RX timeout interrupt */ - buf[10] |= MAX3107_LSR_RXTO_BIT; - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, 22)) - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - - /* 10. Clear IRQ status register by reading it */ - buf[0] = MAX3107_IRQSTS_REG; - - /* 11. Configure interrupt enable register */ - /* Enable LSR interrupt */ - s->irqen_reg = MAX3107_IRQ_LSR_BIT; - /* Enable RX FIFO interrupt */ - s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; - buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG) - | s->irqen_reg; - - /* 12. Clear FIFO reset that was set in step 6 */ - buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); - if (s->loopback) { - /* Keep loopback enabled */ - buf[2] |= MAX3107_MODE2_LOOPBACK_BIT; - } - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6)) - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - -} - -/* IRQ handler */ -static irqreturn_t max3107_irq(int irqno, void *dev_id) -{ - struct max3107_port *s = dev_id; - - if (irqno != s->spi->irq) { - /* Unexpected IRQ */ - return IRQ_NONE; - } - - /* Indicate irq */ - s->handle_irq = 1; - - /* Trigger work thread */ - max3107_dowork(s); - - return IRQ_HANDLED; -} - -/* HW suspension function - * - * Currently autosleep is used to decrease current consumption, alternative - * approach would be to set the chip to reset mode if UART is not being - * used but that would mess the GPIOs - * - */ -void max3107_hw_susp(struct max3107_port *s, int suspend) -{ - pr_debug("enter, suspend %d\n", suspend); - - if (suspend) { - /* Suspend requested, - * enable autosleep to decrease current consumption - */ - s->suspended = 1; - max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP); - } else { - /* Resume requested, - * disable autosleep - */ - s->suspended = 0; - max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP); - } -} -EXPORT_SYMBOL_GPL(max3107_hw_susp); - -/* Modem status IRQ enabling */ -static void max3107_enable_ms(struct uart_port *port) -{ - /* Modem status not supported */ -} - -/* Data send function */ -static void max3107_start_tx(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - /* Trigger work thread for sending data */ - max3107_dowork(s); -} - -/* Function for checking that there is no pending transfers */ -static unsigned int max3107_tx_empty(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - pr_debug("returning %d\n", - (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit))); - return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit); -} - -/* Function for stopping RX */ -static void max3107_stop_rx(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - unsigned long flags; - - /* Set RX disabled in MODE 1 register */ - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT; - s->mode1_commit = 1; - spin_unlock_irqrestore(&s->data_lock, flags); - /* Set RX disabled */ - s->rx_enabled = 0; - /* Trigger work thread for doing the actual configuration change */ - max3107_dowork(s); -} - -/* Function for returning control pin states */ -static unsigned int max3107_get_mctrl(struct uart_port *port) -{ - /* DCD and DSR are not wired and CTS/RTS is handled automatically - * so just indicate DSR and CAR asserted - */ - return TIOCM_DSR | TIOCM_CAR; -} - -/* Function for setting control pin states */ -static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - /* DCD and DSR are not wired and CTS/RTS is hadnled automatically - * so do nothing - */ -} - -/* Function for configuring UART parameters */ -static void max3107_set_termios(struct uart_port *port, - struct ktermios *termios, - struct ktermios *old) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - struct tty_struct *tty; - int baud; - u16 new_lcr = 0; - u32 new_brg = 0; - unsigned long flags; - - if (!port->state) - return; - - tty = port->state->port.tty; - if (!tty) - return; - - /* Get new LCR register values */ - /* Word size */ - if ((termios->c_cflag & CSIZE) == CS7) - new_lcr |= MAX3107_LCR_WORD_LEN_7; - else - new_lcr |= MAX3107_LCR_WORD_LEN_8; - - /* Parity */ - if (termios->c_cflag & PARENB) { - new_lcr |= MAX3107_LCR_PARITY_BIT; - if (!(termios->c_cflag & PARODD)) - new_lcr |= MAX3107_LCR_EVENPARITY_BIT; - } - - /* Stop bits */ - if (termios->c_cflag & CSTOPB) { - /* 2 stop bits */ - new_lcr |= MAX3107_LCR_STOPLEN_BIT; - } - - /* Mask termios capabilities we don't support */ - termios->c_cflag &= ~CMSPAR; - - /* Set status ignore mask */ - s->port.ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - s->port.ignore_status_mask |= MAX3107_ALL_ERRORS; - - /* Set low latency to immediately handle pushed data */ - s->port.state->port.tty->low_latency = 1; - - /* Get new baud rate generator configuration */ - baud = tty_get_baud_rate(tty); - - spin_lock_irqsave(&s->data_lock, flags); - new_brg = get_new_brg(baud, s); - /* if can't find the corrent config, use previous */ - if (!new_brg) { - baud = s->baud; - new_brg = s->brg_cfg; - } - spin_unlock_irqrestore(&s->data_lock, flags); - tty_termios_encode_baud_rate(termios, baud, baud); - s->baud = baud; - - /* Update timeout according to new baud rate */ - uart_update_timeout(port, termios->c_cflag, baud); - - spin_lock_irqsave(&s->data_lock, flags); - if (s->lcr_reg != new_lcr) { - s->lcr_reg = new_lcr; - s->lcr_commit = 1; - } - if (s->brg_cfg != new_brg) { - s->brg_cfg = new_brg; - s->brg_commit = 1; - } - spin_unlock_irqrestore(&s->data_lock, flags); - - /* Trigger work thread for doing the actual configuration change */ - max3107_dowork(s); -} - -/* Port shutdown function */ -static void max3107_shutdown(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - if (s->suspended && s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Free the interrupt */ - free_irq(s->spi->irq, s); - - if (s->workqueue) { - /* Flush and destroy work queue */ - flush_workqueue(s->workqueue); - destroy_workqueue(s->workqueue); - s->workqueue = NULL; - } - - /* Suspend HW */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 1); -} - -/* Port startup function */ -static int max3107_startup(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - /* Initialize work queue */ - s->workqueue = create_freezable_workqueue("max3107"); - if (!s->workqueue) { - dev_err(&s->spi->dev, "Workqueue creation failed\n"); - return -EBUSY; - } - INIT_WORK(&s->work, max3107_work); - - /* Setup IRQ */ - if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING, - "max3107", s)) { - dev_err(&s->spi->dev, "IRQ reguest failed\n"); - destroy_workqueue(s->workqueue); - s->workqueue = NULL; - return -EBUSY; - } - - /* Resume HW */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Init registers */ - max3107_register_init(s); - - return 0; -} - -/* Port type function */ -static const char *max3107_type(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - return s->spi->modalias; -} - -/* Port release function */ -static void max3107_release_port(struct uart_port *port) -{ - /* Do nothing */ -} - -/* Port request function */ -static int max3107_request_port(struct uart_port *port) -{ - /* Do nothing */ - return 0; -} - -/* Port config function */ -static void max3107_config_port(struct uart_port *port, int flags) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - s->port.type = PORT_MAX3107; -} - -/* Port verify function */ -static int max3107_verify_port(struct uart_port *port, - struct serial_struct *ser) -{ - if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3107) - return 0; - - return -EINVAL; -} - -/* Port stop TX function */ -static void max3107_stop_tx(struct uart_port *port) -{ - /* Do nothing */ -} - -/* Port break control function */ -static void max3107_break_ctl(struct uart_port *port, int break_state) -{ - /* We don't support break control, do nothing */ -} - - -/* Port functions */ -static struct uart_ops max3107_ops = { - .tx_empty = max3107_tx_empty, - .set_mctrl = max3107_set_mctrl, - .get_mctrl = max3107_get_mctrl, - .stop_tx = max3107_stop_tx, - .start_tx = max3107_start_tx, - .stop_rx = max3107_stop_rx, - .enable_ms = max3107_enable_ms, - .break_ctl = max3107_break_ctl, - .startup = max3107_startup, - .shutdown = max3107_shutdown, - .set_termios = max3107_set_termios, - .type = max3107_type, - .release_port = max3107_release_port, - .request_port = max3107_request_port, - .config_port = max3107_config_port, - .verify_port = max3107_verify_port, -}; - -/* UART driver data */ -static struct uart_driver max3107_uart_driver = { - .owner = THIS_MODULE, - .driver_name = "ttyMAX", - .dev_name = "ttyMAX", - .nr = 1, -}; - -static int driver_registered = 0; - - - -/* 'Generic' platform data */ -static struct max3107_plat generic_plat_data = { - .loopback = 0, - .ext_clk = 1, - .hw_suspend = max3107_hw_susp, - .polled_mode = 0, - .poll_time = 0, -}; - - -/*******************************************************************/ - -/** - * max3107_probe - SPI bus probe entry point - * @spi: the spi device - * - * SPI wants us to probe this device and if appropriate claim it. - * Perform any platform specific requirements and then initialise - * the device. - */ - -int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata) -{ - struct max3107_port *s; - u16 buf[2]; /* Buffer for SPI transfers */ - int retval; - - pr_info("enter max3107 probe\n"); - - /* Allocate port structure */ - s = kzalloc(sizeof(*s), GFP_KERNEL); - if (!s) { - pr_err("Allocating port structure failed\n"); - return -ENOMEM; - } - - s->pdata = pdata; - - /* SPI Rx buffer - * +2 for RX FIFO interrupt - * disabling and RX level query - */ - s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL); - if (!s->rxbuf) { - pr_err("Allocating RX buffer failed\n"); - retval = -ENOMEM; - goto err_free4; - } - s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL); - if (!s->rxstr) { - pr_err("Allocating RX buffer failed\n"); - retval = -ENOMEM; - goto err_free3; - } - /* SPI Tx buffer - * SPI transfer buffer - * +3 for TX FIFO empty - * interrupt disabling and - * enabling and TX enabling - */ - s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL); - if (!s->txbuf) { - pr_err("Allocating TX buffer failed\n"); - retval = -ENOMEM; - goto err_free2; - } - /* Initialize shared data lock */ - spin_lock_init(&s->data_lock); - - /* SPI intializations */ - dev_set_drvdata(&spi->dev, s); - spi->mode = SPI_MODE_0; - spi->dev.platform_data = pdata; - spi->bits_per_word = 16; - s->ext_clk = pdata->ext_clk; - s->loopback = pdata->loopback; - spi_setup(spi); - s->spi = spi; - - /* Check REV ID to ensure we are talking to what we expect */ - buf[0] = MAX3107_REVID_REG; - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { - dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n"); - retval = -EIO; - goto err_free1; - } - if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 && - (buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) { - dev_err(&s->spi->dev, "REVID %x does not match\n", - (buf[0] & MAX3107_SPI_RX_DATA_MASK)); - retval = -ENODEV; - goto err_free1; - } - - /* Disable all interrupts */ - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000); - buf[0] |= 0x0000; - - /* Configure clock source */ - buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG); - if (s->ext_clk) { - /* External clock */ - buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT; - } - - /* PLL bypass ON */ - buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT; - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, 4)) { - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - retval = -EIO; - goto err_free1; - } - - /* Register UART driver */ - if (!driver_registered) { - retval = uart_register_driver(&max3107_uart_driver); - if (retval) { - dev_err(&s->spi->dev, "Registering UART driver failed\n"); - goto err_free1; - } - driver_registered = 1; - } - - /* Initialize UART port data */ - s->port.fifosize = 128; - s->port.ops = &max3107_ops; - s->port.line = 0; - s->port.dev = &spi->dev; - s->port.uartclk = 9600; - s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; - s->port.irq = s->spi->irq; - s->port.type = PORT_MAX3107; - - /* Add UART port */ - retval = uart_add_one_port(&max3107_uart_driver, &s->port); - if (retval < 0) { - dev_err(&s->spi->dev, "Adding UART port failed\n"); - goto err_free1; - } - - if (pdata->configure) { - retval = pdata->configure(s); - if (retval < 0) - goto err_free1; - } - - /* Go to suspend mode */ - if (pdata->hw_suspend) - pdata->hw_suspend(s, 1); - - return 0; - -err_free1: - kfree(s->txbuf); -err_free2: - kfree(s->rxstr); -err_free3: - kfree(s->rxbuf); -err_free4: - kfree(s); - return retval; -} -EXPORT_SYMBOL_GPL(max3107_probe); - -/* Driver remove function */ -int max3107_remove(struct spi_device *spi) -{ - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_info("enter max3107 remove\n"); - - /* Remove port */ - if (uart_remove_one_port(&max3107_uart_driver, &s->port)) - dev_warn(&s->spi->dev, "Removing UART port failed\n"); - - - /* Free TxRx buffer */ - kfree(s->rxbuf); - kfree(s->rxstr); - kfree(s->txbuf); - - /* Free port structure */ - kfree(s); - - return 0; -} -EXPORT_SYMBOL_GPL(max3107_remove); - -/* Driver suspend function */ -int max3107_suspend(struct spi_device *spi, pm_message_t state) -{ -#ifdef CONFIG_PM - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_debug("enter suspend\n"); - - /* Suspend UART port */ - uart_suspend_port(&max3107_uart_driver, &s->port); - - /* Go to suspend mode */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 1); -#endif /* CONFIG_PM */ - return 0; -} -EXPORT_SYMBOL_GPL(max3107_suspend); - -/* Driver resume function */ -int max3107_resume(struct spi_device *spi) -{ -#ifdef CONFIG_PM - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_debug("enter resume\n"); - - /* Resume from suspend */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Resume UART port */ - uart_resume_port(&max3107_uart_driver, &s->port); -#endif /* CONFIG_PM */ - return 0; -} -EXPORT_SYMBOL_GPL(max3107_resume); - -static int max3107_probe_generic(struct spi_device *spi) -{ - return max3107_probe(spi, &generic_plat_data); -} - -/* Spi driver data */ -static struct spi_driver max3107_driver = { - .driver = { - .name = "max3107", - .owner = THIS_MODULE, - }, - .probe = max3107_probe_generic, - .remove = __devexit_p(max3107_remove), - .suspend = max3107_suspend, - .resume = max3107_resume, -}; - -/* Driver init function */ -static int __init max3107_init(void) -{ - pr_info("enter max3107 init\n"); - return spi_register_driver(&max3107_driver); -} - -/* Driver exit function */ -static void __exit max3107_exit(void) -{ - pr_info("enter max3107 exit\n"); - /* Unregister UART driver */ - if (driver_registered) - uart_unregister_driver(&max3107_uart_driver); - spi_unregister_driver(&max3107_driver); -} - -module_init(max3107_init); -module_exit(max3107_exit); - -MODULE_DESCRIPTION("MAX3107 driver"); -MODULE_AUTHOR("Aavamobile"); -MODULE_ALIAS("spi:max3107"); -MODULE_LICENSE("GPL v2"); diff --git a/drivers/tty/serial/max3107.h b/drivers/tty/serial/max3107.h deleted file mode 100644 index 8415fc723b9..00000000000 --- a/drivers/tty/serial/max3107.h +++ /dev/null @@ -1,441 +0,0 @@ -/* - * max3107.h - spi uart protocol driver header for Maxim 3107 - * - * Copyright (C) Aavamobile 2009 - * Based on serial_max3100.h by Christian Pellegrin - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef _MAX3107_H -#define _MAX3107_H - -/* Serial error status definitions */ -#define MAX3107_PARITY_ERROR 1 -#define MAX3107_FRAME_ERROR 2 -#define MAX3107_OVERRUN_ERROR 4 -#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \ - MAX3107_FRAME_ERROR | \ - MAX3107_OVERRUN_ERROR) - -/* GPIO definitions */ -#define MAX3107_GPIO_BASE 88 -#define MAX3107_GPIO_COUNT 4 - - -/* GPIO connected to chip's reset pin */ -#define MAX3107_RESET_GPIO 87 - - -/* Chip reset delay */ -#define MAX3107_RESET_DELAY 10 - -/* Chip wakeup delay */ -#define MAX3107_WAKEUP_DELAY 50 - - -/* Sleep mode definitions */ -#define MAX3107_DISABLE_FORCED_SLEEP 0 -#define MAX3107_ENABLE_FORCED_SLEEP 1 -#define MAX3107_DISABLE_AUTOSLEEP 2 -#define MAX3107_ENABLE_AUTOSLEEP 3 - - -/* Definitions for register access with SPI transfers - * - * SPI transfer format: - * - * Master to slave bits xzzzzzzzyyyyyyyy - * Slave to master bits aaaaaaaabbbbbbbb - * - * where: - * x = 0 for reads, 1 for writes - * z = register address - * y = new register value if write, 0 if read - * a = unspecified - * b = register value if read, unspecified if write - */ - -/* SPI speed */ -#define MAX3107_SPI_SPEED (3125000 * 2) - -/* Write bit */ -#define MAX3107_WRITE_BIT (1 << 15) - -/* SPI TX data mask */ -#define MAX3107_SPI_RX_DATA_MASK (0x00ff) - -/* SPI RX data mask */ -#define MAX3107_SPI_TX_DATA_MASK (0x00ff) - -/* Register access masks */ -#define MAX3107_RHR_REG (0x0000) /* RX FIFO */ -#define MAX3107_THR_REG (0x0000) /* TX FIFO */ -#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */ -#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */ -#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */ -#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */ -#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */ -#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */ -#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */ -#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */ -#define MAX3107_MODE1_REG (0x0900) /* MODE1 */ -#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */ -#define MAX3107_LCR_REG (0x0b00) /* LCR */ -#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */ -#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */ -#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */ -#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */ -#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */ -#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */ -#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */ -#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */ -#define MAX3107_XON1_REG (0x1400) /* XON1 character */ -#define MAX3107_XON2_REG (0x1500) /* XON2 character */ -#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */ -#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */ -#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */ -#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */ -#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */ -#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */ -#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */ -#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */ -#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */ -#define MAX3107_REVID_REG (0x1f00) /* Revision identification */ - -/* IRQ register bits */ -#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ -#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ -#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */ -#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ -#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ -#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ -#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ -#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ - -/* LSR register bits */ -#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */ -#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ -#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ -#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */ -#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */ -#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ -#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */ - -/* Special character register bits */ -#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ -#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ -#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ -#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ -#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */ -#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ -#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Status register bits */ -#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ -#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ -#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ -#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ -#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */ -#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ -#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ -#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* MODE1 register bits */ -#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ -#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ -#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ -#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ -#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ -#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ -#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ -#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ - -/* MODE2 register bits */ -#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */ -#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ -#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ -#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ -#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ -#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ -#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ -#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ - -/* LCR register bits */ -#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ -#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 - * - * Word length bits table: - * 00 -> 5 bit words - * 01 -> 6 bit words - * 10 -> 7 bit words - * 11 -> 8 bit words - */ -#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit - * - * STOP length bit table: - * 0 -> 1 stop bit - * 1 -> 1-1.5 stop bits if - * word length is 5, - * 2 stop bits otherwise - */ -#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ -#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ -#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ -#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ -#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */ -#define MAX3107_LCR_WORD_LEN_5 (0x0000) -#define MAX3107_LCR_WORD_LEN_6 (0x0001) -#define MAX3107_LCR_WORD_LEN_7 (0x0002) -#define MAX3107_LCR_WORD_LEN_8 (0x0003) - - -/* IRDA register bits */ -#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ -#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ -#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ -#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ -#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ -#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ -#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Flow control trigger level register masks */ -#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ -#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ -#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f) -#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4) - -/* FIFO interrupt trigger level register masks */ -#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */ -#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */ -#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f) -#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4) - -/* Flow control register bits */ -#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ -#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ -#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs - * are used in conjunction with - * XOFF2 for definition of - * special character */ -#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ -#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ -#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 - * - * SWFLOW bits 1 & 0 table: - * 00 -> no transmitter flow - * control - * 01 -> receiver compares - * XON2 and XOFF2 - * and controls - * transmitter - * 10 -> receiver compares - * XON1 and XOFF1 - * and controls - * transmitter - * 11 -> receiver compares - * XON1, XON2, XOFF1 and - * XOFF2 and controls - * transmitter - */ -#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ -#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 - * - * SWFLOW bits 3 & 2 table: - * 00 -> no received flow - * control - * 01 -> transmitter generates - * XON2 and XOFF2 - * 10 -> transmitter generates - * XON1 and XOFF1 - * 11 -> transmitter generates - * XON1, XON2, XOFF1 and - * XOFF2 - */ - -/* GPIO configuration register bits */ -#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ -#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ -#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ -#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ -#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ -#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ -#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ -#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ - -/* GPIO DATA register bits */ -#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ -#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ -#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ -#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ -#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ -#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ -#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ -#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ - -/* PLL configuration register masks */ -#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */ -#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */ - -/* Baud rate generator configuration register masks and bits */ -#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of - * Baud rate generator divisor - */ -#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ -#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ -#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Clock source register bits */ -#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */ -#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ -#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ -#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ -#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ -#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */ -#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ - - -/* HW definitions */ -#define MAX3107_RX_FIFO_SIZE 128 -#define MAX3107_TX_FIFO_SIZE 128 -#define MAX3107_REVID1 0x00a0 -#define MAX3107_REVID2 0x00a1 - - -/* Baud rate generator configuration values for external clock 13MHz */ -#define MAX3107_BRG13_B300 (0x0A9400 | 0x05) -#define MAX3107_BRG13_B600 (0x054A00 | 0x03) -#define MAX3107_BRG13_B1200 (0x02A500 | 0x01) -#define MAX3107_BRG13_B2400 (0x015200 | 0x09) -#define MAX3107_BRG13_B4800 (0x00A900 | 0x04) -#define MAX3107_BRG13_B9600 (0x005400 | 0x0A) -#define MAX3107_BRG13_B19200 (0x002A00 | 0x05) -#define MAX3107_BRG13_B38400 (0x001500 | 0x03) -#define MAX3107_BRG13_B57600 (0x000E00 | 0x02) -#define MAX3107_BRG13_B115200 (0x000700 | 0x01) -#define MAX3107_BRG13_B230400 (0x000300 | 0x08) -#define MAX3107_BRG13_B460800 (0x000100 | 0x0c) -#define MAX3107_BRG13_B921600 (0x000100 | 0x1c) - -/* Baud rate generator configuration values for external clock 26MHz */ -#define MAX3107_BRG26_B300 (0x152800 | 0x0A) -#define MAX3107_BRG26_B600 (0x0A9400 | 0x05) -#define MAX3107_BRG26_B1200 (0x054A00 | 0x03) -#define MAX3107_BRG26_B2400 (0x02A500 | 0x01) -#define MAX3107_BRG26_B4800 (0x015200 | 0x09) -#define MAX3107_BRG26_B9600 (0x00A900 | 0x04) -#define MAX3107_BRG26_B19200 (0x005400 | 0x0A) -#define MAX3107_BRG26_B38400 (0x002A00 | 0x05) -#define MAX3107_BRG26_B57600 (0x001C00 | 0x03) -#define MAX3107_BRG26_B115200 (0x000E00 | 0x02) -#define MAX3107_BRG26_B230400 (0x000700 | 0x01) -#define MAX3107_BRG26_B460800 (0x000300 | 0x08) -#define MAX3107_BRG26_B921600 (0x000100 | 0x0C) - -/* Baud rate generator configuration values for internal clock */ -#define MAX3107_BRG13_IB300 (0x008000 | 0x00) -#define MAX3107_BRG13_IB600 (0x004000 | 0x00) -#define MAX3107_BRG13_IB1200 (0x002000 | 0x00) -#define MAX3107_BRG13_IB2400 (0x001000 | 0x00) -#define MAX3107_BRG13_IB4800 (0x000800 | 0x00) -#define MAX3107_BRG13_IB9600 (0x000400 | 0x00) -#define MAX3107_BRG13_IB19200 (0x000200 | 0x00) -#define MAX3107_BRG13_IB38400 (0x000100 | 0x00) -#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B) -#define MAX3107_BRG13_IB115200 (0x000000 | 0x05) -#define MAX3107_BRG13_IB230400 (0x000000 | 0x03) -#define MAX3107_BRG13_IB460800 (0x000000 | 0x00) -#define MAX3107_BRG13_IB921600 (0x000000 | 0x00) - - -struct baud_table { - int baud; - u32 new_brg; -}; - -struct max3107_port { - /* UART port structure */ - struct uart_port port; - - /* SPI device structure */ - struct spi_device *spi; - -#if defined(CONFIG_GPIOLIB) - /* GPIO chip structure */ - struct gpio_chip chip; -#endif - - /* Workqueue that does all the magic */ - struct workqueue_struct *workqueue; - struct work_struct work; - - /* Lock for shared data */ - spinlock_t data_lock; - - /* Device configuration */ - int ext_clk; /* 1 if external clock used */ - int loopback; /* Current loopback mode state */ - int baud; /* Current baud rate */ - - /* State flags */ - int suspended; /* Indicates suspend mode */ - int tx_fifo_empty; /* Flag for TX FIFO state */ - int rx_enabled; /* Flag for receiver state */ - int tx_enabled; /* Flag for transmitter state */ - - u16 irqen_reg; /* Current IRQ enable register value */ - /* Shared data */ - u16 mode1_reg; /* Current mode1 register value*/ - int mode1_commit; /* Flag for setting new mode1 register value */ - u16 lcr_reg; /* Current LCR register value */ - int lcr_commit; /* Flag for setting new LCR register value */ - u32 brg_cfg; /* Current Baud rate generator config */ - int brg_commit; /* Flag for setting new baud rate generator - * config - */ - struct baud_table *baud_tbl; - int handle_irq; /* Indicates that IRQ should be handled */ - - /* Rx buffer and str*/ - u16 *rxbuf; - u8 *rxstr; - /* Tx buffer*/ - u16 *txbuf; - - struct max3107_plat *pdata; /* Platform data */ -}; - -/* Platform data structure */ -struct max3107_plat { - /* Loopback mode enable */ - int loopback; - /* External clock enable */ - int ext_clk; - /* Called during the register initialisation */ - void (*init)(struct max3107_port *s); - /* Called when the port is found and configured */ - int (*configure)(struct max3107_port *s); - /* HW suspend function */ - void (*hw_suspend) (struct max3107_port *s, int suspend); - /* Polling mode enable */ - int polled_mode; - /* Polling period if polling mode enabled */ - int poll_time; -}; - -extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len); -extern void max3107_hw_susp(struct max3107_port *s, int suspend); -extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata); -extern int max3107_remove(struct spi_device *spi); -extern int max3107_suspend(struct spi_device *spi, pm_message_t state); -extern int max3107_resume(struct spi_device *spi); - -#endif /* _LINUX_SERIAL_MAX3107_H */ diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c new file mode 100644 index 00000000000..534e44851b7 --- /dev/null +++ b/drivers/tty/serial/max310x.c @@ -0,0 +1,1259 @@ +/* + * Maxim (Dallas) MAX3107/8 serial driver + * + * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru> + * + * Based on max3100.c, by Christian Pellegrin <chripell@evolware.org> + * Based on max3110.c, by Feng Tang <feng.tang@intel.com> + * Based on max3107.c, by Aavamobile + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +/* TODO: MAX3109 support (Dual) */ +/* TODO: MAX14830 support (Quad) */ + +#include <linux/module.h> +#include <linux/device.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/regmap.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/platform_data/max310x.h> + +#define MAX310X_MAJOR 204 +#define MAX310X_MINOR 209 + +/* MAX310X register definitions */ +#define MAX310X_RHR_REG (0x00) /* RX FIFO */ +#define MAX310X_THR_REG (0x00) /* TX FIFO */ +#define MAX310X_IRQEN_REG (0x01) /* IRQ enable */ +#define MAX310X_IRQSTS_REG (0x02) /* IRQ status */ +#define MAX310X_LSR_IRQEN_REG (0x03) /* LSR IRQ enable */ +#define MAX310X_LSR_IRQSTS_REG (0x04) /* LSR IRQ status */ +#define MAX310X_SPCHR_IRQEN_REG (0x05) /* Special char IRQ enable */ +#define MAX310X_SPCHR_IRQSTS_REG (0x06) /* Special char IRQ status */ +#define MAX310X_STS_IRQEN_REG (0x07) /* Status IRQ enable */ +#define MAX310X_STS_IRQSTS_REG (0x08) /* Status IRQ status */ +#define MAX310X_MODE1_REG (0x09) /* MODE1 */ +#define MAX310X_MODE2_REG (0x0a) /* MODE2 */ +#define MAX310X_LCR_REG (0x0b) /* LCR */ +#define MAX310X_RXTO_REG (0x0c) /* RX timeout */ +#define MAX310X_HDPIXDELAY_REG (0x0d) /* Auto transceiver delays */ +#define MAX310X_IRDA_REG (0x0e) /* IRDA settings */ +#define MAX310X_FLOWLVL_REG (0x0f) /* Flow control levels */ +#define MAX310X_FIFOTRIGLVL_REG (0x10) /* FIFO IRQ trigger levels */ +#define MAX310X_TXFIFOLVL_REG (0x11) /* TX FIFO level */ +#define MAX310X_RXFIFOLVL_REG (0x12) /* RX FIFO level */ +#define MAX310X_FLOWCTRL_REG (0x13) /* Flow control */ +#define MAX310X_XON1_REG (0x14) /* XON1 character */ +#define MAX310X_XON2_REG (0x15) /* XON2 character */ +#define MAX310X_XOFF1_REG (0x16) /* XOFF1 character */ +#define MAX310X_XOFF2_REG (0x17) /* XOFF2 character */ +#define MAX310X_GPIOCFG_REG (0x18) /* GPIO config */ +#define MAX310X_GPIODATA_REG (0x19) /* GPIO data */ +#define MAX310X_PLLCFG_REG (0x1a) /* PLL config */ +#define MAX310X_BRGCFG_REG (0x1b) /* Baud rate generator conf */ +#define MAX310X_BRGDIVLSB_REG (0x1c) /* Baud rate divisor LSB */ +#define MAX310X_BRGDIVMSB_REG (0x1d) /* Baud rate divisor MSB */ +#define MAX310X_CLKSRC_REG (0x1e) /* Clock source */ +/* Only present in MAX3107 */ +#define MAX3107_REVID_REG (0x1f) /* Revision identification */ + +/* IRQ register bits */ +#define MAX310X_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ +#define MAX310X_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ +#define MAX310X_IRQ_STS_BIT (1 << 2) /* Status interrupt */ +#define MAX310X_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ +#define MAX310X_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ +#define MAX310X_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ +#define MAX310X_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ +#define MAX310X_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ + +/* LSR register bits */ +#define MAX310X_LSR_RXTO_BIT (1 << 0) /* RX timeout */ +#define MAX310X_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ +#define MAX310X_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ +#define MAX310X_LSR_FRERR_BIT (1 << 3) /* Frame error */ +#define MAX310X_LSR_RXBRK_BIT (1 << 4) /* RX break */ +#define MAX310X_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ +#define MAX310X_LSR_CTS_BIT (1 << 7) /* CTS pin state */ + +/* Special character register bits */ +#define MAX310X_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ +#define MAX310X_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ +#define MAX310X_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ +#define MAX310X_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ +#define MAX310X_SPCHR_BREAK_BIT (1 << 4) /* RX break */ +#define MAX310X_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ + +/* Status register bits */ +#define MAX310X_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ +#define MAX310X_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ +#define MAX310X_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ +#define MAX310X_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ +#define MAX310X_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ +#define MAX310X_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ + +/* MODE1 register bits */ +#define MAX310X_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ +#define MAX310X_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ +#define MAX310X_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ +#define MAX310X_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ +#define MAX310X_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ +#define MAX310X_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ +#define MAX310X_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ +#define MAX310X_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ + +/* MODE2 register bits */ +#define MAX310X_MODE2_RST_BIT (1 << 0) /* Chip reset */ +#define MAX310X_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ +#define MAX310X_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ +#define MAX310X_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ +#define MAX310X_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ +#define MAX310X_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ +#define MAX310X_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ +#define MAX310X_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ + +/* LCR register bits */ +#define MAX310X_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ +#define MAX310X_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 + * + * Word length bits table: + * 00 -> 5 bit words + * 01 -> 6 bit words + * 10 -> 7 bit words + * 11 -> 8 bit words + */ +#define MAX310X_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit + * + * STOP length bit table: + * 0 -> 1 stop bit + * 1 -> 1-1.5 stop bits if + * word length is 5, + * 2 stop bits otherwise + */ +#define MAX310X_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ +#define MAX310X_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ +#define MAX310X_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ +#define MAX310X_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ +#define MAX310X_LCR_RTS_BIT (1 << 7) /* RTS pin control */ +#define MAX310X_LCR_WORD_LEN_5 (0x00) +#define MAX310X_LCR_WORD_LEN_6 (0x01) +#define MAX310X_LCR_WORD_LEN_7 (0x02) +#define MAX310X_LCR_WORD_LEN_8 (0x03) + +/* IRDA register bits */ +#define MAX310X_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ +#define MAX310X_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ +#define MAX310X_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ +#define MAX310X_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ +#define MAX310X_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ +#define MAX310X_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ + +/* Flow control trigger level register masks */ +#define MAX310X_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ +#define MAX310X_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ +#define MAX310X_FLOWLVL_HALT(words) ((words / 8) & 0x0f) +#define MAX310X_FLOWLVL_RES(words) (((words / 8) & 0x0f) << 4) + +/* FIFO interrupt trigger level register masks */ +#define MAX310X_FIFOTRIGLVL_TX_MASK (0x0f) /* TX FIFO trigger level */ +#define MAX310X_FIFOTRIGLVL_RX_MASK (0xf0) /* RX FIFO trigger level */ +#define MAX310X_FIFOTRIGLVL_TX(words) ((words / 8) & 0x0f) +#define MAX310X_FIFOTRIGLVL_RX(words) (((words / 8) & 0x0f) << 4) + +/* Flow control register bits */ +#define MAX310X_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ +#define MAX310X_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ +#define MAX310X_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs + * are used in conjunction with + * XOFF2 for definition of + * special character */ +#define MAX310X_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ +#define MAX310X_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ +#define MAX310X_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 + * + * SWFLOW bits 1 & 0 table: + * 00 -> no transmitter flow + * control + * 01 -> receiver compares + * XON2 and XOFF2 + * and controls + * transmitter + * 10 -> receiver compares + * XON1 and XOFF1 + * and controls + * transmitter + * 11 -> receiver compares + * XON1, XON2, XOFF1 and + * XOFF2 and controls + * transmitter + */ +#define MAX310X_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ +#define MAX310X_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 + * + * SWFLOW bits 3 & 2 table: + * 00 -> no received flow + * control + * 01 -> transmitter generates + * XON2 and XOFF2 + * 10 -> transmitter generates + * XON1 and XOFF1 + * 11 -> transmitter generates + * XON1, XON2, XOFF1 and + * XOFF2 + */ + +/* GPIO configuration register bits */ +#define MAX310X_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ +#define MAX310X_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ +#define MAX310X_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ +#define MAX310X_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ +#define MAX310X_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ +#define MAX310X_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ +#define MAX310X_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ +#define MAX310X_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ + +/* GPIO DATA register bits */ +#define MAX310X_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ +#define MAX310X_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ +#define MAX310X_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ +#define MAX310X_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ +#define MAX310X_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ +#define MAX310X_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ +#define MAX310X_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ +#define MAX310X_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ + +/* PLL configuration register masks */ +#define MAX310X_PLLCFG_PREDIV_MASK (0x3f) /* PLL predivision value */ +#define MAX310X_PLLCFG_PLLFACTOR_MASK (0xc0) /* PLL multiplication factor */ + +/* Baud rate generator configuration register bits */ +#define MAX310X_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ +#define MAX310X_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ + +/* Clock source register bits */ +#define MAX310X_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ +#define MAX310X_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ +#define MAX310X_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ +#define MAX310X_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ +#define MAX310X_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ + +/* Misc definitions */ +#define MAX310X_FIFO_SIZE (128) + +/* MAX3107 specific */ +#define MAX3107_REV_ID (0xa0) +#define MAX3107_REV_MASK (0xfe) + +/* IRQ status bits definitions */ +#define MAX310X_IRQ_TX (MAX310X_IRQ_TXFIFO_BIT | \ + MAX310X_IRQ_TXEMPTY_BIT) +#define MAX310X_IRQ_RX (MAX310X_IRQ_RXFIFO_BIT | \ + MAX310X_IRQ_RXEMPTY_BIT) + +/* Supported chip types */ +enum { + MAX310X_TYPE_MAX3107 = 3107, + MAX310X_TYPE_MAX3108 = 3108, +}; + +struct max310x_port { + struct uart_driver uart; + struct uart_port port; + + const char *name; + int uartclk; + + unsigned int nr_gpio; +#ifdef CONFIG_GPIOLIB + struct gpio_chip gpio; +#endif + + struct regmap *regmap; + struct regmap_config regcfg; + + struct workqueue_struct *wq; + struct work_struct tx_work; + + struct mutex max310x_mutex; + + struct max310x_pdata *pdata; +}; + +static bool max3107_8_reg_writeable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_IRQSTS_REG: + case MAX310X_LSR_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + case MAX310X_TXFIFOLVL_REG: + case MAX310X_RXFIFOLVL_REG: + case MAX3107_REVID_REG: /* Only available on MAX3107 */ + return false; + default: + break; + } + + return true; +} + +static bool max310x_reg_volatile(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_RHR_REG: + case MAX310X_IRQSTS_REG: + case MAX310X_LSR_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + case MAX310X_TXFIFOLVL_REG: + case MAX310X_RXFIFOLVL_REG: + case MAX310X_GPIODATA_REG: + return true; + default: + break; + } + + return false; +} + +static bool max310x_reg_precious(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_RHR_REG: + case MAX310X_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + return true; + default: + break; + } + + return false; +} + +static void max310x_set_baud(struct max310x_port *s, int baud) +{ + unsigned int mode = 0, div = s->uartclk / baud; + + if (!(div / 16)) { + /* Mode x2 */ + mode = MAX310X_BRGCFG_2XMODE_BIT; + div = (s->uartclk * 2) / baud; + } + + if (!(div / 16)) { + /* Mode x4 */ + mode = MAX310X_BRGCFG_4XMODE_BIT; + div = (s->uartclk * 4) / baud; + } + + regmap_write(s->regmap, MAX310X_BRGDIVMSB_REG, + ((div / 16) >> 8) & 0xff); + regmap_write(s->regmap, MAX310X_BRGDIVLSB_REG, (div / 16) & 0xff); + regmap_write(s->regmap, MAX310X_BRGCFG_REG, (div % 16) | mode); +} + +static void max310x_wait_pll(struct max310x_port *s) +{ + int tryes = 1000; + + /* Wait for PLL only if crystal is used */ + if (!(s->pdata->driver_flags & MAX310X_EXT_CLK)) { + unsigned int sts = 0; + + while (tryes--) { + regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &sts); + if (sts & MAX310X_STS_CLKREADY_BIT) + break; + } + } +} + +static int __devinit max310x_update_best_err(unsigned long f, long *besterr) +{ + /* Use baudrate 115200 for calculate error */ + long err = f % (115200 * 16); + + if ((*besterr < 0) || (*besterr > err)) { + *besterr = err; + return 0; + } + + return 1; +} + +static int __devinit max310x_set_ref_clk(struct max310x_port *s) +{ + unsigned int div, clksrc, pllcfg = 0; + long besterr = -1; + unsigned long fdiv, fmul, bestfreq = s->pdata->frequency; + + /* First, update error without PLL */ + max310x_update_best_err(s->pdata->frequency, &besterr); + + /* Try all possible PLL dividers */ + for (div = 1; (div <= 63) && besterr; div++) { + fdiv = DIV_ROUND_CLOSEST(s->pdata->frequency, div); + + /* Try multiplier 6 */ + fmul = fdiv * 6; + if ((fdiv >= 500000) && (fdiv <= 800000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (0 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 48 */ + fmul = fdiv * 48; + if ((fdiv >= 850000) && (fdiv <= 1200000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (1 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 96 */ + fmul = fdiv * 96; + if ((fdiv >= 425000) && (fdiv <= 1000000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (2 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 144 */ + fmul = fdiv * 144; + if ((fdiv >= 390000) && (fdiv <= 667000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (3 << 6) | div; + bestfreq = fmul; + } + } + + /* Configure clock source */ + if (s->pdata->driver_flags & MAX310X_EXT_CLK) + clksrc = MAX310X_CLKSRC_EXTCLK_BIT; + else + clksrc = MAX310X_CLKSRC_CRYST_BIT; + + /* Configure PLL */ + if (pllcfg) { + clksrc |= MAX310X_CLKSRC_PLL_BIT; + regmap_write(s->regmap, MAX310X_PLLCFG_REG, pllcfg); + } else + clksrc |= MAX310X_CLKSRC_PLLBYP_BIT; + + regmap_write(s->regmap, MAX310X_CLKSRC_REG, clksrc); + + if (pllcfg) + max310x_wait_pll(s); + + dev_dbg(s->port.dev, "Reference clock set to %lu Hz\n", bestfreq); + + return (int)bestfreq; +} + +static void max310x_handle_rx(struct max310x_port *s, unsigned int rxlen) +{ + unsigned int sts = 0, ch = 0, flag; + struct tty_struct *tty = tty_port_tty_get(&s->port.state->port); + + if (!tty) + return; + + if (unlikely(rxlen >= MAX310X_FIFO_SIZE)) { + dev_warn(s->port.dev, "Possible RX FIFO overrun %d\n", rxlen); + /* Ensure sanity of RX level */ + rxlen = MAX310X_FIFO_SIZE; + } + + dev_dbg(s->port.dev, "RX Len = %u\n", rxlen); + + while (rxlen--) { + regmap_read(s->regmap, MAX310X_RHR_REG, &ch); + regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &sts); + + sts &= MAX310X_LSR_RXPAR_BIT | MAX310X_LSR_FRERR_BIT | + MAX310X_LSR_RXOVR_BIT | MAX310X_LSR_RXBRK_BIT; + + s->port.icount.rx++; + flag = TTY_NORMAL; + + if (unlikely(sts)) { + if (sts & MAX310X_LSR_RXBRK_BIT) { + s->port.icount.brk++; + if (uart_handle_break(&s->port)) + continue; + } else if (sts & MAX310X_LSR_RXPAR_BIT) + s->port.icount.parity++; + else if (sts & MAX310X_LSR_FRERR_BIT) + s->port.icount.frame++; + else if (sts & MAX310X_LSR_RXOVR_BIT) + s->port.icount.overrun++; + + sts &= s->port.read_status_mask; + if (sts & MAX310X_LSR_RXBRK_BIT) + flag = TTY_BREAK; + else if (sts & MAX310X_LSR_RXPAR_BIT) + flag = TTY_PARITY; + else if (sts & MAX310X_LSR_FRERR_BIT) + flag = TTY_FRAME; + else if (sts & MAX310X_LSR_RXOVR_BIT) + flag = TTY_OVERRUN; + } + + if (uart_handle_sysrq_char(s->port, ch)) + continue; + + if (sts & s->port.ignore_status_mask) + continue; + + uart_insert_char(&s->port, sts, MAX310X_LSR_RXOVR_BIT, + ch, flag); + } + + tty_flip_buffer_push(tty); + + tty_kref_put(tty); +} + +static void max310x_handle_tx(struct max310x_port *s) +{ + struct circ_buf *xmit = &s->port.state->xmit; + unsigned int txlen = 0, to_send; + + if (unlikely(s->port.x_char)) { + regmap_write(s->regmap, MAX310X_THR_REG, s->port.x_char); + s->port.icount.tx++; + s->port.x_char = 0; + return; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port)) + return; + + /* Get length of data pending in circular buffer */ + to_send = uart_circ_chars_pending(xmit); + if (likely(to_send)) { + /* Limit to size of TX FIFO */ + regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &txlen); + txlen = MAX310X_FIFO_SIZE - txlen; + to_send = (to_send > txlen) ? txlen : to_send; + + dev_dbg(s->port.dev, "TX Len = %u\n", to_send); + + /* Add data to send */ + s->port.icount.tx += to_send; + while (to_send--) { + regmap_write(s->regmap, MAX310X_THR_REG, + xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + }; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&s->port); +} + +static irqreturn_t max310x_ist(int irq, void *dev_id) +{ + struct max310x_port *s = (struct max310x_port *)dev_id; + unsigned int ists = 0, lsr = 0, rxlen = 0; + + mutex_lock(&s->max310x_mutex); + + for (;;) { + /* Read IRQ status & RX FIFO level */ + regmap_read(s->regmap, MAX310X_IRQSTS_REG, &ists); + regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &lsr); + regmap_read(s->regmap, MAX310X_RXFIFOLVL_REG, &rxlen); + if (!ists && !(lsr & MAX310X_LSR_RXTO_BIT) && !rxlen) + break; + + dev_dbg(s->port.dev, "IRQ status: 0x%02x\n", ists); + + if (rxlen) + max310x_handle_rx(s, rxlen); + if (ists & MAX310X_IRQ_TX) + max310x_handle_tx(s); + if (ists & MAX310X_IRQ_CTS_BIT) + uart_handle_cts_change(&s->port, + !!(lsr & MAX310X_LSR_CTS_BIT)); + } + + mutex_unlock(&s->max310x_mutex); + + return IRQ_HANDLED; +} + +static void max310x_wq_proc(struct work_struct *ws) +{ + struct max310x_port *s = container_of(ws, struct max310x_port, tx_work); + + mutex_lock(&s->max310x_mutex); + max310x_handle_tx(s); + mutex_unlock(&s->max310x_mutex); +} + +static void max310x_start_tx(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + queue_work(s->wq, &s->tx_work); +} + +static void max310x_stop_tx(struct uart_port *port) +{ + /* Do nothing */ +} + +static void max310x_stop_rx(struct uart_port *port) +{ + /* Do nothing */ +} + +static unsigned int max310x_tx_empty(struct uart_port *port) +{ + unsigned int val = 0; + struct max310x_port *s = container_of(port, struct max310x_port, port); + + mutex_lock(&s->max310x_mutex); + regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &val); + mutex_unlock(&s->max310x_mutex); + + return val ? 0 : TIOCSER_TEMT; +} + +static void max310x_enable_ms(struct uart_port *port) +{ + /* Modem status not supported */ +} + +static unsigned int max310x_get_mctrl(struct uart_port *port) +{ + /* DCD and DSR are not wired and CTS/RTS is handled automatically + * so just indicate DSR and CAR asserted + */ + return TIOCM_DSR | TIOCM_CAR; +} + +static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + /* DCD and DSR are not wired and CTS/RTS is hadnled automatically + * so do nothing + */ +} + +static void max310x_break_ctl(struct uart_port *port, int break_state) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + mutex_lock(&s->max310x_mutex); + regmap_update_bits(s->regmap, MAX310X_LCR_REG, + MAX310X_LCR_TXBREAK_BIT, + break_state ? MAX310X_LCR_TXBREAK_BIT : 0); + mutex_unlock(&s->max310x_mutex); +} + +static void max310x_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + unsigned int lcr, flow = 0; + int baud; + + mutex_lock(&s->max310x_mutex); + + /* Mask termios capabilities we don't support */ + termios->c_cflag &= ~CMSPAR; + termios->c_iflag &= ~IXANY; + + /* Word size */ + switch (termios->c_cflag & CSIZE) { + case CS5: + lcr = MAX310X_LCR_WORD_LEN_5; + break; + case CS6: + lcr = MAX310X_LCR_WORD_LEN_6; + break; + case CS7: + lcr = MAX310X_LCR_WORD_LEN_7; + break; + case CS8: + default: + lcr = MAX310X_LCR_WORD_LEN_8; + break; + } + + /* Parity */ + if (termios->c_cflag & PARENB) { + lcr |= MAX310X_LCR_PARITY_BIT; + if (!(termios->c_cflag & PARODD)) + lcr |= MAX310X_LCR_EVENPARITY_BIT; + } + + /* Stop bits */ + if (termios->c_cflag & CSTOPB) + lcr |= MAX310X_LCR_STOPLEN_BIT; /* 2 stops */ + + /* Update LCR register */ + regmap_write(s->regmap, MAX310X_LCR_REG, lcr); + + /* Set read status mask */ + port->read_status_mask = MAX310X_LSR_RXOVR_BIT; + if (termios->c_iflag & INPCK) + port->read_status_mask |= MAX310X_LSR_RXPAR_BIT | + MAX310X_LSR_FRERR_BIT; + if (termios->c_iflag & (BRKINT | PARMRK)) + port->read_status_mask |= MAX310X_LSR_RXBRK_BIT; + + /* Set status ignore mask */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNBRK) + port->ignore_status_mask |= MAX310X_LSR_RXBRK_BIT; + if (!(termios->c_cflag & CREAD)) + port->ignore_status_mask |= MAX310X_LSR_RXPAR_BIT | + MAX310X_LSR_RXOVR_BIT | + MAX310X_LSR_FRERR_BIT | + MAX310X_LSR_RXBRK_BIT; + + /* Configure flow control */ + regmap_write(s->regmap, MAX310X_XON1_REG, termios->c_cc[VSTART]); + regmap_write(s->regmap, MAX310X_XOFF1_REG, termios->c_cc[VSTOP]); + if (termios->c_cflag & CRTSCTS) + flow |= MAX310X_FLOWCTRL_AUTOCTS_BIT | + MAX310X_FLOWCTRL_AUTORTS_BIT; + if (termios->c_iflag & IXON) + flow |= MAX310X_FLOWCTRL_SWFLOW3_BIT | + MAX310X_FLOWCTRL_SWFLOWEN_BIT; + if (termios->c_iflag & IXOFF) + flow |= MAX310X_FLOWCTRL_SWFLOW1_BIT | + MAX310X_FLOWCTRL_SWFLOWEN_BIT; + regmap_write(s->regmap, MAX310X_FLOWCTRL_REG, flow); + + /* Get baud rate generator configuration */ + baud = uart_get_baud_rate(port, termios, old, + port->uartclk / 16 / 0xffff, + port->uartclk / 4); + + /* Setup baudrate generator */ + max310x_set_baud(s, baud); + + /* Update timeout according to new baud rate */ + uart_update_timeout(port, termios->c_cflag, baud); + + mutex_unlock(&s->max310x_mutex); +} + +static int max310x_startup(struct uart_port *port) +{ + unsigned int val, line = port->line; + struct max310x_port *s = container_of(port, struct max310x_port, port); + + if (s->pdata->suspend) + s->pdata->suspend(0); + + mutex_lock(&s->max310x_mutex); + + /* Configure baud rate, 9600 as default */ + max310x_set_baud(s, 9600); + + /* Configure LCR register, 8N1 mode by default */ + val = MAX310X_LCR_WORD_LEN_8; + regmap_write(s->regmap, MAX310X_LCR_REG, val); + + /* Configure MODE1 register */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_TRNSCVCTRL_BIT, + (s->pdata->uart_flags[line] & MAX310X_AUTO_DIR_CTRL) + ? MAX310X_MODE1_TRNSCVCTRL_BIT : 0); + + /* Configure MODE2 register */ + val = MAX310X_MODE2_RXEMPTINV_BIT; + if (s->pdata->uart_flags[line] & MAX310X_LOOPBACK) + val |= MAX310X_MODE2_LOOPBACK_BIT; + if (s->pdata->uart_flags[line] & MAX310X_ECHO_SUPRESS) + val |= MAX310X_MODE2_ECHOSUPR_BIT; + + /* Reset FIFOs */ + val |= MAX310X_MODE2_FIFORST_BIT; + regmap_write(s->regmap, MAX310X_MODE2_REG, val); + + /* Configure FIFO trigger level register */ + /* RX FIFO trigger for 16 words, TX FIFO trigger for 64 words */ + val = MAX310X_FIFOTRIGLVL_RX(16) | MAX310X_FIFOTRIGLVL_TX(64); + regmap_write(s->regmap, MAX310X_FIFOTRIGLVL_REG, val); + + /* Configure flow control levels */ + /* Flow control halt level 96, resume level 48 */ + val = MAX310X_FLOWLVL_RES(48) | MAX310X_FLOWLVL_HALT(96); + regmap_write(s->regmap, MAX310X_FLOWLVL_REG, val); + + /* Clear timeout register */ + regmap_write(s->regmap, MAX310X_RXTO_REG, 0); + + /* Configure LSR interrupt enable register */ + /* Enable RX timeout interrupt */ + val = MAX310X_LSR_RXTO_BIT; + regmap_write(s->regmap, MAX310X_LSR_IRQEN_REG, val); + + /* Clear FIFO reset */ + regmap_update_bits(s->regmap, MAX310X_MODE2_REG, + MAX310X_MODE2_FIFORST_BIT, 0); + + /* Clear IRQ status register by reading it */ + regmap_read(s->regmap, MAX310X_IRQSTS_REG, &val); + + /* Configure interrupt enable register */ + /* Enable CTS change interrupt */ + val = MAX310X_IRQ_CTS_BIT; + /* Enable RX, TX interrupts */ + val |= MAX310X_IRQ_RX | MAX310X_IRQ_TX; + regmap_write(s->regmap, MAX310X_IRQEN_REG, val); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} + +static void max310x_shutdown(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + /* Disable all interrupts */ + mutex_lock(&s->max310x_mutex); + regmap_write(s->regmap, MAX310X_IRQEN_REG, 0); + mutex_unlock(&s->max310x_mutex); + + if (s->pdata->suspend) + s->pdata->suspend(1); +} + +static const char *max310x_type(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + return (port->type == PORT_MAX310X) ? s->name : NULL; +} + +static int max310x_request_port(struct uart_port *port) +{ + /* Do nothing */ + return 0; +} + +static void max310x_release_port(struct uart_port *port) +{ + /* Do nothing */ +} + +static void max310x_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) + port->type = PORT_MAX310X; +} + +static int max310x_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if ((ser->type == PORT_UNKNOWN) || (ser->type == PORT_MAX310X)) + return 0; + if (ser->irq == port->irq) + return 0; + + return -EINVAL; +} + +static struct uart_ops max310x_ops = { + .tx_empty = max310x_tx_empty, + .set_mctrl = max310x_set_mctrl, + .get_mctrl = max310x_get_mctrl, + .stop_tx = max310x_stop_tx, + .start_tx = max310x_start_tx, + .stop_rx = max310x_stop_rx, + .enable_ms = max310x_enable_ms, + .break_ctl = max310x_break_ctl, + .startup = max310x_startup, + .shutdown = max310x_shutdown, + .set_termios = max310x_set_termios, + .type = max310x_type, + .request_port = max310x_request_port, + .release_port = max310x_release_port, + .config_port = max310x_config_port, + .verify_port = max310x_verify_port, +}; + +static int max310x_suspend(struct spi_device *spi, pm_message_t state) +{ + int ret; + struct max310x_port *s = dev_get_drvdata(&spi->dev); + + dev_dbg(&spi->dev, "Suspend\n"); + + ret = uart_suspend_port(&s->uart, &s->port); + + mutex_lock(&s->max310x_mutex); + + /* Enable sleep mode */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_FORCESLEEP_BIT, + MAX310X_MODE1_FORCESLEEP_BIT); + + mutex_unlock(&s->max310x_mutex); + + if (s->pdata->suspend) + s->pdata->suspend(1); + + return ret; +} + +static int max310x_resume(struct spi_device *spi) +{ + struct max310x_port *s = dev_get_drvdata(&spi->dev); + + dev_dbg(&spi->dev, "Resume\n"); + + if (s->pdata->suspend) + s->pdata->suspend(0); + + mutex_lock(&s->max310x_mutex); + + /* Disable sleep mode */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_FORCESLEEP_BIT, + 0); + + max310x_wait_pll(s); + + mutex_unlock(&s->max310x_mutex); + + return uart_resume_port(&s->uart, &s->port); +} + +#ifdef CONFIG_GPIOLIB +static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + unsigned int val = 0; + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + regmap_read(s->regmap, MAX310X_GPIODATA_REG, &val); + mutex_unlock(&s->max310x_mutex); + + return !!((val >> 4) & (1 << offset)); +} + +static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ? + 1 << offset : 0); + mutex_unlock(&s->max310x_mutex); +} + +static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + + regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset, 0); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} + +static int max310x_gpio_direction_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + + regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset, + 1 << offset); + regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ? + 1 << offset : 0); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} +#endif + +/* Generic platform data */ +static struct max310x_pdata generic_plat_data = { + .driver_flags = MAX310X_EXT_CLK, + .uart_flags[0] = MAX310X_ECHO_SUPRESS, + .frequency = 26000000, +}; + +static int __devinit max310x_probe(struct spi_device *spi) +{ + struct max310x_port *s; + struct device *dev = &spi->dev; + int chiptype = spi_get_device_id(spi)->driver_data; + struct max310x_pdata *pdata = dev->platform_data; + unsigned int val = 0; + int ret; + + /* Check for IRQ */ + if (spi->irq <= 0) { + dev_err(dev, "No IRQ specified\n"); + return -ENOTSUPP; + } + + /* Alloc port structure */ + s = devm_kzalloc(dev, sizeof(struct max310x_port), GFP_KERNEL); + if (!s) { + dev_err(dev, "Error allocating port structure\n"); + return -ENOMEM; + } + dev_set_drvdata(dev, s); + + if (!pdata) { + dev_warn(dev, "No platform data supplied, using defaults\n"); + pdata = &generic_plat_data; + } + s->pdata = pdata; + + /* Individual chip settings */ + switch (chiptype) { + case MAX310X_TYPE_MAX3107: + s->name = "MAX3107"; + s->nr_gpio = 4; + s->uart.nr = 1; + s->regcfg.max_register = 0x1f; + break; + case MAX310X_TYPE_MAX3108: + s->name = "MAX3108"; + s->nr_gpio = 4; + s->uart.nr = 1; + s->regcfg.max_register = 0x1e; + break; + default: + dev_err(dev, "Unsupported chip type %i\n", chiptype); + return -ENOTSUPP; + } + + /* Check input frequency */ + if ((pdata->driver_flags & MAX310X_EXT_CLK) && + ((pdata->frequency < 500000) || (pdata->frequency > 35000000))) + goto err_freq; + /* Check frequency for quartz */ + if (!(pdata->driver_flags & MAX310X_EXT_CLK) && + ((pdata->frequency < 1000000) || (pdata->frequency > 4000000))) + goto err_freq; + + mutex_init(&s->max310x_mutex); + + /* Setup SPI bus */ + spi->mode = SPI_MODE_0; + spi->bits_per_word = 8; + spi->max_speed_hz = 26000000; + spi_setup(spi); + + /* Setup regmap */ + s->regcfg.reg_bits = 8; + s->regcfg.val_bits = 8; + s->regcfg.read_flag_mask = 0x00; + s->regcfg.write_flag_mask = 0x80; + s->regcfg.cache_type = REGCACHE_RBTREE; + s->regcfg.writeable_reg = max3107_8_reg_writeable; + s->regcfg.volatile_reg = max310x_reg_volatile; + s->regcfg.precious_reg = max310x_reg_precious; + s->regmap = devm_regmap_init_spi(spi, &s->regcfg); + if (IS_ERR(s->regmap)) { + ret = PTR_ERR(s->regmap); + dev_err(dev, "Failed to initialize register map\n"); + goto err_out; + } + + /* Reset chip & check SPI function */ + ret = regmap_write(s->regmap, MAX310X_MODE2_REG, MAX310X_MODE2_RST_BIT); + if (ret) { + dev_err(dev, "SPI transfer failed\n"); + goto err_out; + } + /* Clear chip reset */ + regmap_write(s->regmap, MAX310X_MODE2_REG, 0); + + switch (chiptype) { + case MAX310X_TYPE_MAX3107: + /* Check REV ID to ensure we are talking to what we expect */ + regmap_read(s->regmap, MAX3107_REVID_REG, &val); + if (((val & MAX3107_REV_MASK) != MAX3107_REV_ID)) { + dev_err(dev, "%s ID 0x%02x does not match\n", + s->name, val); + ret = -ENODEV; + goto err_out; + } + break; + case MAX310X_TYPE_MAX3108: + /* MAX3108 have not REV ID register, we just check default value + * from clocksource register to make sure everything works. + */ + regmap_read(s->regmap, MAX310X_CLKSRC_REG, &val); + if (val != (MAX310X_CLKSRC_EXTCLK_BIT | + MAX310X_CLKSRC_PLLBYP_BIT)) { + dev_err(dev, "%s not present\n", s->name); + ret = -ENODEV; + goto err_out; + } + break; + } + + /* Board specific configure */ + if (pdata->init) + pdata->init(); + if (pdata->suspend) + pdata->suspend(0); + + /* Calculate referecne clock */ + s->uartclk = max310x_set_ref_clk(s); + + /* Disable all interrupts */ + regmap_write(s->regmap, MAX310X_IRQEN_REG, 0); + + /* Setup MODE1 register */ + val = MAX310X_MODE1_IRQSEL_BIT; /* Enable IRQ pin */ + if (pdata->driver_flags & MAX310X_AUTOSLEEP) + val = MAX310X_MODE1_AUTOSLEEP_BIT; + regmap_write(s->regmap, MAX310X_MODE1_REG, val); + + /* Setup interrupt */ + ret = devm_request_threaded_irq(dev, spi->irq, NULL, max310x_ist, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + dev_name(dev), s); + if (ret) { + dev_err(dev, "Unable to reguest IRQ %i\n", spi->irq); + goto err_out; + } + + /* Register UART driver */ + s->uart.owner = THIS_MODULE; + s->uart.driver_name = dev_name(dev); + s->uart.dev_name = "ttyMAX"; + s->uart.major = MAX310X_MAJOR; + s->uart.minor = MAX310X_MINOR; + ret = uart_register_driver(&s->uart); + if (ret) { + dev_err(dev, "Registering UART driver failed\n"); + goto err_out; + } + + /* Initialize workqueue for start TX */ + s->wq = create_freezable_workqueue(dev_name(dev)); + INIT_WORK(&s->tx_work, max310x_wq_proc); + + /* Initialize UART port data */ + s->port.line = 0; + s->port.dev = dev; + s->port.irq = spi->irq; + s->port.type = PORT_MAX310X; + s->port.fifosize = MAX310X_FIFO_SIZE; + s->port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE; + s->port.iotype = UPIO_PORT; + s->port.membase = (void __iomem *)0xffffffff; /* Bogus value */ + s->port.uartclk = s->uartclk; + s->port.ops = &max310x_ops; + uart_add_one_port(&s->uart, &s->port); + +#ifdef CONFIG_GPIOLIB + /* Setup GPIO cotroller */ + if (pdata->gpio_base) { + s->gpio.owner = THIS_MODULE; + s->gpio.dev = dev; + s->gpio.label = dev_name(dev); + s->gpio.direction_input = max310x_gpio_direction_input; + s->gpio.get = max310x_gpio_get; + s->gpio.direction_output= max310x_gpio_direction_output; + s->gpio.set = max310x_gpio_set; + s->gpio.base = pdata->gpio_base; + s->gpio.ngpio = s->nr_gpio; + if (gpiochip_add(&s->gpio)) { + /* Indicate that we should not call gpiochip_remove */ + s->gpio.base = 0; + } + } else + dev_info(dev, "GPIO support not enabled\n"); +#endif + + /* Go to suspend mode */ + if (pdata->suspend) + pdata->suspend(1); + + return 0; + +err_freq: + dev_err(dev, "Frequency parameter incorrect\n"); + ret = -EINVAL; + +err_out: + dev_set_drvdata(dev, NULL); + devm_kfree(dev, s); + + return ret; +} + +static int __devexit max310x_remove(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct max310x_port *s = dev_get_drvdata(dev); + + dev_dbg(dev, "Removing port\n"); + + devm_free_irq(dev, s->port.irq, s); + + destroy_workqueue(s->wq); + + uart_remove_one_port(&s->uart, &s->port); + + uart_unregister_driver(&s->uart); + +#ifdef CONFIG_GPIOLIB + if (s->pdata->gpio_base) + gpiochip_remove(&s->gpio); +#endif + + dev_set_drvdata(dev, NULL); + + if (s->pdata->suspend) + s->pdata->suspend(1); + if (s->pdata->exit) + s->pdata->exit(); + + devm_kfree(dev, s); + + return 0; +} + +static const struct spi_device_id max310x_id_table[] = { + { "max3107", MAX310X_TYPE_MAX3107 }, + { "max3108", MAX310X_TYPE_MAX3108 }, +}; +MODULE_DEVICE_TABLE(spi, max310x_id_table); + +static struct spi_driver max310x_driver = { + .driver = { + .name = "max310x", + .owner = THIS_MODULE, + }, + .probe = max310x_probe, + .remove = __devexit_p(max310x_remove), + .suspend = max310x_suspend, + .resume = max310x_resume, + .id_table = max310x_id_table, +}; +module_spi_driver(max310x_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>"); +MODULE_DESCRIPTION("MAX310X serial driver"); diff --git a/include/linux/platform_data/max310x.h b/include/linux/platform_data/max310x.h new file mode 100644 index 00000000000..91648bf5fc5 --- /dev/null +++ b/include/linux/platform_data/max310x.h @@ -0,0 +1,67 @@ +/* + * Maxim (Dallas) MAX3107/8 serial driver + * + * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru> + * + * Based on max3100.c, by Christian Pellegrin <chripell@evolware.org> + * Based on max3110.c, by Feng Tang <feng.tang@intel.com> + * Based on max3107.c, by Aavamobile + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef _MAX310X_H_ +#define _MAX310X_H_ + +/* + * Example board initialization data: + * + * static struct max310x_pdata max3107_pdata = { + * .driver_flags = MAX310X_EXT_CLK, + * .uart_flags[0] = MAX310X_ECHO_SUPRESS | MAX310X_AUTO_DIR_CTRL, + * .frequency = 3686400, + * .gpio_base = -1, + * }; + * + * static struct spi_board_info spi_device_max3107[] = { + * { + * .modalias = "max3107", + * .irq = IRQ_EINT3, + * .bus_num = 1, + * .chip_select = 1, + * .platform_data = &max3107_pdata, + * }, + * }; + */ + +#define MAX310X_MAX_UARTS 1 + +/* MAX310X platform data structure */ +struct max310x_pdata { + /* Flags global to driver */ + const u8 driver_flags:2; +#define MAX310X_EXT_CLK (0x00000001) /* External clock enable */ +#define MAX310X_AUTOSLEEP (0x00000002) /* Enable AutoSleep mode */ + /* Flags global to UART port */ + const u8 uart_flags[MAX310X_MAX_UARTS]; +#define MAX310X_LOOPBACK (0x00000001) /* Loopback mode enable */ +#define MAX310X_ECHO_SUPRESS (0x00000002) /* Enable echo supress */ +#define MAX310X_AUTO_DIR_CTRL (0x00000004) /* Enable Auto direction + * control (RS-485) + */ + /* Frequency (extrenal clock or crystal) */ + const int frequency; + /* GPIO base number (can be negative) */ + const int gpio_base; + /* Called during startup */ + void (*init)(void); + /* Called before finish */ + void (*exit)(void); + /* Suspend callback */ + void (*suspend)(int do_suspend); +}; + +#endif diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 0253c2022e5..7cf0b68bbe9 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -193,8 +193,8 @@ /* SH-SCI */ #define PORT_SCIFB 93 -/* MAX3107 */ -#define PORT_MAX3107 94 +/* MAX310X */ +#define PORT_MAX310X 94 /* High Speed UART for Medfield */ #define PORT_MFD 95 |